Search NASA⌕ Search

SEARCH · Search NASA

Results for “sample average approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

129 I, 99 Tc, and U Distribution Coefficients of Subsurface Sediments Collected from the Proposed Site of the Environmental Management Disposal Facility

Performance Assessment calculations were completed in 2020 to evaluate the Environmental Management Disposal Facility (EMDF), a proposed new low-level radioactive waste (LLW) disposal facility on the U.S. Department of Energy’s Oak Ridge Reservation (ORR). Among the large number of input parameters needed for such calculations, are distribution coefficients (K d values; radionuclide concentration solid: liquid ratio) that provide a measure of the tendency of radionuclides to bind to sediments. The objective of this study was to measure K d values of three radionuclides that may pose a disproportionately large amount of risk, U, iodine-129 ( 129 I) and technetium-99 ( 99 Tc). The average 129 I K d value for the 14 geological materials recovered from the proposed EMDF site was 37.8 mL/g and ranged from 0.45 to 140.9 mL/g. These values were consistent, but somewhat larger than previous measurements made with ORR sediments and were about an order of magnitude greater than those used in previous EMDF PA calculations. The median 99 Tc K d value was 365.7 mL/g, much greater than previously reported using ORR geological materials. Five of the 14 tested geological materials sorbed large quantities of 99 Tc, suggesting that the weakly sorbing 99 Tc(VII) species had been reduced to the sparingly soluble 99 Tc(IV) species. The five strongly sorbing sediments had apparent 99 Tc solubility values of approximately <10 -8 mol/L. The median U K d value was 5,726 mL/g. All of the tested geological materials had large K d values, ranging from 625 to >10,208 mL/g. Among the sediment samples that exhibited strong U binding, the apparent solubility value was approximately <10 -9 mol/L. Based on sediment properties and general ORR geological considerations, it was proposed that much of the 129 I and 99 Tc retention could be attributed to the site materials exhibiting low pH (average pH = 4.94), and/or the elevated levels of iron oxides, manganese oxides, and natural organic matter. Similarly, the extremely high U binding measured in these sediments may also be attributed to the low conditions of carbonates, which can complex and therefore solubilize uranyl in these tests due to the low pH, and also the relatively high concentrations of iron and organic coatings on these samples. An implication of this study is that the areas of the EMDF subsurface environment may have natural properties for attenuating 129 I, 99 Tc, and U movement, and potentially other radionuclides, thereby possibly reducing risk posed by burial of LLW at this site.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hopping crossover and high-temperature superspin glass behavior in Ni films deposited on MoS 2

Realizing the potential of MoS 2 and other two-dimensional semiconductors in spintronic devices requires a fundamental understanding of their interaction with ferromagnetic metals. We have investigated the transport and magnetic properties of thin Ni films grown on single-crystal MoS 2 substrates. The Ni is found to have a granular morphology with an average grain size of approximately 2 nm. Like previously investigated granular Ni/insulator composites below the percolation threshold, transport is found to proceed via hopping. However, our Ni/MoS 2 sample exhibits a dual crossover: activated hopping to 𝑇−1/2 variable-range hopping at a higher temperature and then a transition to power-law behavior at a lower temperature. The magnetoresistance was used as a novel probe for uncovering superspin-glass-like behavior above room temperature in the Ni/MoS 2 nanostructure, which also exhibits a collective ferromagnetic state at very low temperatures, reminiscent of superferromagnetism.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Wood Decomposition: Understanding Processes Regulating Carbon Transfer to Soil Carbon Pools Using FACE Wood at Multiple Scales

Dead wood comprises approximately 20% of forest biomass. While it is widely recognized for its role in ecosystem functions relative to habitat and nutrient cycling, there are considerable uncertainties associated with its role in the forest carbon (C) cycle. The principal uncertainty is whether dead wood contributes to the soil C pool. With little supporting evidence, the presumption is that C in wood is respired back to the atmosphere through decomposition processes. The inability to attribute forest soil C to its source components has been a barrier to addressing this important forest carbon cycle question. The U.S. Dept. of Energy’s Free Air CO 2 Enrichment (FACE) experiment produced wood that has a distinct δ 13 C signature that can be used to trace its fate through organic matter decomposition processes. Using two hardwood species (aspen, birch) from the Rhinelander FACE site and pine from the Duke FACE site, the FACE Wood Decomposition Experiment (FWDE) was established in 2011 to provide the foundation for addressing wood decomposition and its associated processes at the continental scale. Plots were installed on nine experimental forests representing a range in bioclimatic forest conditions within the continental U.S. Each identical plot has logs of the three species incubating on the soil surface and pine logs suspended in the air, representing standing dead wood. Abiotic conditions are monitored continuously, and soil and forest conditions characterized. Logs on the sites have been measured every two years to assess decay. This project was initiated in 2016 with specific objectives to: (a) determine whether dead wood C contributes to the soil C pool, (b) assess the fungal community composition mediating the decay, (c) assess the interactions of termites with microbial decay, and (d) develop a mechanistic model to simulate wood decomposition. The principal field sampling was conducted in 2017; correspondingly, the results reported here represent six years of decomposition. Wood decomposition varied from 13 to 75 % loss across the bioclimatic gradient. Sites in the southeastern U.S. coastal plain and piedmont had fastest decomposition rates for each of the species. In contrast sites in the Rocky Mountains had the slowest decay rates, which were associated with cold temperatures. Standing deadwood decomposes at a much slower rate than logs on the soil surface; a response due to differences in wood moisture content. Wood carbon was measured in the mineral soil across each of the sites; accordingly, this is the first study to affirm that a portion of the wood C does become part of the soil C pool. Averaged across the FWDE sites, approximately 1.4% of the soil C in the upper 10 cm of the mineral soil directly beneath the log was derived from the deadwood; within 50 cm of the log, wood C accounted for an average of 2.1%. These results demonstrate that the contribution of deadwood to the soil C pool is a soil volume surrounding the log; and it’s likely a larger volume than what we sampled. We also hypothesized that there would be more wood C in the mineral soil when termites were present. However, that hypothesis wasn’t supported by measurements on the Santee Experimental Forest termite exclusion (SEF-TX) plots under FACE logs that incubated for 6 years. Across all the sites, the majority of the wood C was transferred to the atmosphere. Approximately 7,000 fungal species were sequenced. The fungal communities were different among each of the sites suggesting local colonization; interestingly, within sites the three species also exhibited differences in fungal community composition. White rot was the dominant fungal form in pine and hardwood, which yields less lignin in the wood residue. Brown rot occurred in approximately 20% of the pine and aspen logs, and it did not occur in birch logs. The occurrence of brown rot was only weakly correlated to site factors. We conducted two additional experiments to assess the effects of termites on wood decomposition and the associated interactions with the fungal community. Pine and birch logs were incubated on the Santee Experimental Forest termite exclusion plots in upland and riparian settings. There was no difference in decay between areas where termites were able colonize and plots where they had been excluded. Highly variable foraging by termites was a primary contributor the result. Correspondingly, fungal communities did not vary on logs incubated among the two treatments, but they did reflect site and species differences. The second experiment was conducted on each of the nine FWDE sites where pine and birch wood blocks were incubated for two years with and without a wrapping designed to exclude termites and other arthropods. The effects of termites on wood decomposition could be confirmed on two of the four sites known to have subterranean termites. On the two southeastern sites, termites contributed approximately 8% to mass loss in pine blocks over two years. A major factor clouding the role of termites in wood decomposition is the inability to assess the time, duration, and intensity of the foraging with the logs. Another uncertainty is related to whether a piece of wood will be foraged. A process-based wood decomposition model was developed representing biological processes mediated by fungi, bacteria, termites, beetles, as well as physical and chemical processes. The Coarse Wood Decomposition Model (CWDM) was parameterized based on a thorough review of the literature and it was validated using data from the FWDE. In the initial setup, the model considers softwoods and hardwoods groups, as opposed to individual species. Sensitivity analyses incorporating climate data from 89 locations in North America demonstrated that CWDM was stable from the tropics to the boreal zone. Model calibration and validation showed it to perform very well. The CWDM is poised for additional testing with subsequent FWDE data as well as other data sets, and it is available for incorporation into forest biogeochemical models or DOEs Earth System Modeling framework.

54 ENVIRONMENTAL SCIENCES↗

Analysis of sparse recovery for Legendre expansions using envelope bound

We provide novel sufficient conditions for the uniform recovery of sparse Legendre expansions using ℓ 1 minimization, where the sampling points are drawn according to orthogonalization (uniform) measure. So far, conditions of the form m ≳ Θ 2 s x log factors have been relied on to determine the minimum number of samples m that guarantees successful reconstruction of s-sparse vectors when the measurement matrix is associated to an orthonormal system. However, in case of sparse Legendre expansions, the uniform bound Θ of Legendre systems is so high that these conditions are unable to provide meaningful guarantees. Here, in this paper, we present an analysis which employs the envelop bound of all Legendre polynomials instead, and prove a new recovery guarantee for s-sparse Legendre expansions, m ≳ Θs 2 x log factors, which is independent of Θ. Arguably, this is the first recovery condition established for orthonormal systems without assuming the uniform boundedness of the sampling matrix. The key ingredient of our analysis is an extension of chaining arguments, recently developed in Bourgain and Chkifa et al., to handle the envelope bound. Furthermore, our recovery condition is proved via restricted eigenvalue property, a less demanding replacement of restricted isometry property which is perfectly suited to the considered scenario. Along the way, we derive simple criteria to detect good sample sets. Our numerical tests show that sets of uniformly sampled points that meet these criteria will perform better recovery on average.

97 MATHEMATICS AND COMPUTING↗

First measurement of the characteristic depletion radius of dark matter haloes from weak lensing

ABSTRACT We use weak lensing observations to make the first measurement of the characteristic depletion radius, one of the three radii that characterize the region where matter is being depleted by growing haloes. The lenses are taken from the halo catalogue produced by the extended halo-based group/cluster finder applied to DESI Legacy Imaging Surveys DR9, while the sources are extracted from the DECaLS DR8 imaging data with the fourier_quad pipeline. We study halo masses $12 \lt \log (M_{\rm grp} \,[{\rm M_{\odot }}\, h^{-1}]) \le 15.3$ within redshifts 0.2 ≤ z ≤ 0.3. The virial and splashback radii are also measured and used to test the original findings on the depletion region. When binning haloes by mass, we find consistency between most of our measurements and predictions from the cosmicgrowth simulation, with exceptions to the lowest mass bins. The characteristic depletion radius is found to be roughly 2.5 times the virial radius and 1.7–3 times the splashback radius, in line with an approximately universal outer density profile, and the average enclosed density within the characteristic depletion radius is found to be roughly 29 times the mean matter density of the Universe in our sample. When binning haloes by both mass and a proxy for halo concentration, we do not detect a significant variation of the depletion radius with concentration, on which the simulation prediction is also sensitive to the choice of concentration proxy. We also confirm that the measured splashback radius varies with concentration differently from simulation predictions.

79 ASTRONOMY AND ASTROPHYSICS↗

A new method for inferring city emissions and lifetimes of nitrogen oxides from high-resolution nitrogen dioxide observations: a model study

We present a new method to infer emissions and lifetimes of nitrogen oxides (NO x ) based on tropospheric nitrogen dioxide (NO 2 ) observations together with reanalysis wind fields for cities located in polluted backgrounds. Since the accuracy of the method is difficult to assess due to lack of “true values” that can be used as a benchmark, we apply the method to synthetic NO 2 observations derived from the NASA-Unified Weather Research and Forecasting (NU-WRF) model at a high horizontal spatial resolution of 4 km × 4 km for cities over the continental United States. We compare the inferred emissions and lifetimes with the values given by the NU-WRF model to evaluate the method. The method is applicable to 26 US cities. The derived results are generally in good agreement with the values given by the model, with the relative differences of 2 % ± 17 % (mean ± standard deviation) and 15 % ± 25 % for lifetimes and emissions, respectively. Our investigation suggests that the use of wind data prior to the satellite overpass time improves the performance of the method. The correlation coefficients between inferred and NU-WRF lifetimes increase from 0.56 to 0.79 and for emissions increase from 0.88 to 0.96 when comparing results based on wind fields sampled simultaneously with satellite observations and averaged over 9 h data prior to satellite observations, respectively. We estimate that uncertainties in NO x lifetime and emissions arising from the method are approximately 15 % and 20 %, respectively, for typical (US) cities. The total uncertainties reach up to 43% (lifetimes) and 45% (emissions) by considering the additional uncertainties associated with satellite NO 2 observations and wind data. We expect this new method to be applicable to NO 2 observations from the TROPOspheric Monitoring Instrument (TROPOMI) and geostationary satellites, such as Geostationary Environment Monitoring Spectrometer (GEMS) or the Tropospheric Emissions: Monitoring Pollution (TEMPO) instrument, to estimate urban NO x emissions and lifetimes globally.

54 ENVIRONMENTAL SCIENCES↗

Investigation of the approach used in the unresolved resonance region

The typical practice used in Monte Carlo neutron transport codes in the unresolved resonance region (URR) is to take advantage of the probability table (PT) approach. Cross sections are sampled from PTs and used as needed, along with generated average cross sections. The PTs are generated based on cross-section calculations performed using the single-level Breit–Wigner approximation. Although the approach used in the URR seems plausible, a detailed examination was needed to understand the benchmark results obtained using specific tests.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Could on-site fuel storage economically reduce power plant-gas grid dependence in pipeline constrained areas like New England?

In the Northeastern United States, natural gas supply constraints have led to periods when gas shortages have caused up to a quarter of all unscheduled power plant outages. Dual fuel oil/gas generators or local gas storage might mitigate gas supply shortages. We use historical power plant operational and availability data to develop a supply curve of the costs required for generators to mitigate fuel shortage failures in New England. Based on 2012–2018 data, we find that the historical fuel shortages at approximately 2 GW worth of gas-fired capacity could be mitigated using on-site fuel storage. For comparison, New England’s average reserve margin was 1.7–2.8 GW over our sample period. Oil dual fuel plants would recoup their investment if compensated with a reliability adder of $\$ 3-7$/MWh during their normal operations, while $\$ 7-16$/MWh would incentivize using onsite, compressed natural gas storage. We estimate that the capital expenses associated with the fuel storage options would be less expensive than installing battery backup for resource adequacy at current battery prices.

03 NATURAL GAS↗

Analysis of Exposure during Transportation of Waste to the Nevada National Security Site (NNSS) - 20445

Safety is a priority for the U.S. Department of Energy (DOE) Environmental Management (EM) Nevada Program. This commitment to safety is integrated into requirements and work procedures at DOE sites across the U.S. that generate low-level radioactive waste, mixed low-level radioactive waste, and classified waste that is transported to the Nevada National Security Site (NNSS) for permanent disposal. Generators of this waste are responsible for ensuring it is packaged and transported in a safe and compliant manner. These generators and their contracted commercial carriers must comply with U.S. Department of Transportation (DOT) regulations; the Nevada National Security Site Waste Acceptance Criteria (NNSSWAC); and other applicable federal, state, and local regulations and requirements. This includes packaging and shipping the waste to meet DOT regulatory radiation dose limits to ensure public safety during transportation. NNSS waste generators have a solid safety record for complying with these stringent regulations as demonstrated by the fact that no shipments exceeding DOT dose rate limits were received at the NNSS Area 5 Radioactive Waste Management Complex (RWMC) during FY 2014 through FY 2018. A 2005 study conducted by the Desert Research Institute validated shipments to the NNSS comply with DOT radiation dose limits. In response to recent Nevada stakeholder requests for an updated study, an analysis was conducted to verify and provide evidence that the public continues to be safe from exposure to radioactive waste shipment to the NNSS. Radiation exposure from radioactive waste shipments in transit to the NNSS was evaluated. Three studies were performed: 1. Confirm compliance of waste shipments to the DOT radiation limits using dose rate surveys taken at the generator site and at the disposal site. 2. Estimate the dose to the public from waste shipments using the dosimetry results for disposal site personnel by comparing time of exposure for various individuals/scenarios. 3. Estimate the truck driver dose using the receipt dose rate surveys and time of exposure, and from dosimetry results. Study 1 confirmed compliance with the DOT dose rate limits for a sample of waste shipments (123 of 1,038) received during fiscal year (FY) 2017. Study 2 showed that the average annual radiation equivalent dose for disposal site personnel during FY 2017 was approximately 6.7% [0.415 mSv (41.5 millirem)] of the annual average dose that a person living in the U.S. receives from all sources [6.2 mSv (620 mrem)]. Maximum dose to a member of the public, a person resting/sleeping in an adjacent truck at a rest area to a waste shipment, was 0.0166 mSv (1.66 mrem), which is less than the dose received from a person taking a round trip from the east coast to the west coast of the continental U.S. on an airplane [0.07 mSv (7 mrem) per round trip]. Study 3 showed that the truck driver who made the most shipments of radioactive waste to the NNSS, who drove the most hours (estimated time of exposure 2,520 hours), during FY 2017 had a total dose of 0.15 mSv (15 mrem), which was obtained from their personal dosimeter. The annual dose recorded for disposal site personnel, the dose estimates for the public, and the truck driver dose were all a small percentage of the average radiation dose a person receives from all sources (e.g., background and medical radiation). At these levels, risk should only be described qualitatively. Radiation exposure from radioactive waste shipments to the NNSS were shown to be compliant with the DOT dose rate limits, safe, and very low (i.e., within background levels). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Reinforcement learning for real-time process control in high-temperature superconductor manufacturing

With high efficiency and low energy loss, high-temperature superconductors (HTS) have demonstrated their profound applications in various fields, such as medical imaging, transportation, accelerators, microwave devices, and power systems. The high-field applications of HTS tapes have raised the demand for producing cost-effective tapes with long lengths in superconductor manufacturing. However, achieving the uniform and enhanced performance of a long HTS tape is challenging due to the unstable growth conditions in the manufacturing process. Although it is confirmed that the process parameters during the advanced metal organic chemical vapor deposition (A-MOCVD) process influence the uniformity of the produced HTS tapes, the high-dimensional process parameter signals and their complicated interactions make it difficult to develop an effective control policy. In this paper, we propose a local measure for the uniformity of HTS tapes to provide instant feedback for our control policy. Then, we model the manufacturing of HTS tapes as a Markov decision process (MDP) with continuous state and action spaces to assess the instant reward in real time in our feedback control model. As our MDP involves continuous and high-dimensional state and action spaces, a neural fitted Q-iteration (NFQ) algorithm is adopted to solve the MDP with artificial neural network (ANN) function approximation. The collinearity of process parameters can restrict our capability of adjusting the process parameters, which is addressed by the principal component analysis (PCA) in our method. The control policy adjusts the PCA of process parameters using the NFQ algorithm. In conclusion, based on our case studies on real A-MOCVD dataset, the obtained control policy increases the average uniformity of tapes by 5.6% and performs especially well on sample HTS tapes with a low uniformity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Absolute light yield of the EJ-204 plastic scintillator

The absolute light yield of a scintillator, defined as the number of scintillation photons produced per unit energy deposited, is a useful quantity for scintillator development, research, and applications. Yet, literature data on the absolute light yield of organic scintillators are limited. The goal of this work is to assess the suitability of the EJ-204 plastic scintillator from Eljen Technology to serve as a reference standard for measurements of the absolute light yield of organic scintillators. Four EJ-204 samples were examined: two manufactured approximately four months prior and stored in high-purity nitrogen, and two aged approximately eleven years and stored in ambient air. The scintillator response was measured using a large-area avalanche photodiode calibrated using low energy $γ$-ray and X-ray sources. The product of the quantum efficiency of the photodetector and light collection efficiency of the housing was characterized using an experimentally-benchmarked optical photon simulation. The average absolute light yield of the fresh samples, 9100 ± 400 photons per MeV, is lower than the manufacturer-reported value of 10400 photons per MeV. Moreover, the aged samples demonstrated significantly lower light yields, deviating from the manufacturer specification by as much as 26%. These results are consistent with recent work showcasing environmental aging in plastic scintillators and suggest that experimenters should use caution when deploying plastic scintillators in photon counting applications.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Noncoplanar ferrimagnetism and local crystalline-electric-field anisotropy in the quasicrystal approximant Au 70 Si 17 Tb 13

Neutron scattering experiments have been performed to elucidate magnetic properties of the quasicrystal approximant Au 70 Si 17 Tb 13 , consisting of icosahedral spin clusters in a body-centered-cubic lattice. Bulk magnetic measurements performed on the single crystalline sample unambiguously confirm long-range ordering at T C = 11.6 ± 1 K. In contrast to the simple ferromagnetic response in the bulk measurements, single crystal neutron diffraction confirms a formation of intriguing non-collinear and non-coplanar magnetic order. The magnetic moment direction was found to be nearly tangential to the icosahedral cluster surface in the local mirror plane, which is quite similar to that recently found in the antiferromagnetic quasicrystal approximant Au 72 Al 14 Tb 14 . Inelastic neutron scattering on the powdered sample exhibits a very broad peak centered at hω ≃ 4 meV. The observed inelastic spectrum was explained by the crystalline-electric-field model taking account of the chemical disorder at the fractional Au/Si sites. The resulting averaged anisotropy axis for the crystalline-electric-field ground state is consistent with the ordered moment direction determined in the magnetic structure analysis, confirming that the non-coplanar magnetic order is stabilized by the local uniaxial anisotropy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Experimental calibration of an Fe3+/Fe2+-in-amphibole oxybarometer and its application to shallow magmatic processes at Shiveluch Volcano, Kamchatka

Abstract Oxygen fugacity is an important but difficult parameter to constrain for primitive arc magmas. In this study, the partitioning behavior of Fe3+/Fe2+ between amphibole and glass synthesized in piston-cylinder and cold-seal apparatus experiments is developed as an oxybarometer, applicable to magmas ranging from basaltic to dacitic composition. The partitioning of Fe2+ is strongly dependent on melt polymerization; the relative compatibility of Fe2+ in amphibole decreases with increasing polymerization. The Fe2+/Mg distribution coefficient between amphibole and melt is a relatively constant value across all compositions and is, on average, 0.27. The amphibole oxybarometer is applied to amphibole in mafic enclaves, cumulates, and basaltic tephra erupted from Shiveluch volcano in Kamchatka with measured Fe3+/FeTotal. An average Fe3+/Fe2+ amphibole-glass distribution coefficient for basalt is used to convert the Fe3+/FeTotal of amphibole in samples from Shiveluch to magmatic oxygen fugacity relative to NNO. The fO2 of primitive melts at the volcano is approximately NNO+2 and is faithfully recorded in amphibole from an amphibole-rich cumulate and the basaltic tephra. Apparently, higher fO2 recorded by amphibole in mafic enclaves likely results from partial dehydrogenation of amphibole during residence in a shallow andesite storage region. We identify three pulses of mafic magma recharge within two weeks of, a month before, and two to three months before the eruption and find that, at each of these times, the host andesite was recharged by at least two magmas at varying stages of differentiation. Application of the amphibole oxybarometer not only gives insight into magmatic fO2 but also potentially details of shallow magmatic processes.

Geochemistry & Geophysics↗

PhaseT3M: 3D imaging at 1.6 Å resolution via electron cryo-tomography with nonlinear phase retrieval

Electron cryo-tomography (cryo-ET) enables 3D imaging of complex, radiation-sensitive structures with molecular detail. However, image contrast from the interference of scattered electrons is nonlinear with atomic density and multiple scattering further complicates interpretation. These effects degrade resolution, particularly in conventional reconstruction algorithms, which assume linearity. Particle averaging can reduce such issues but is unsuitable for heterogeneous or dynamic samples ubiquitous in biology, chemistry, and materials sciences. Here, we develop a phase retrieval-based cryo-ET method, PhaseT3M. We experimentally demonstrate its application to an approximately 7 nm Co3O4 nanoparticle on an approximately 30 nm carbon substrate, achieving a maximum resolution of 1.6 Å, surpassing conventional limits using standard cryo-TEM equipment. PhaseT3M uses a multislice model for multiple scattering and Bayesian optimization for alignment and computational aberration correction, with a positivity constraint to recover ‘missing wedge’ information. Applied directly to biological particles, it enhances reconstruction quality and reduces artifacts, establishing a standard for routine 3D imaging with phase contrast.

Biophysics↗

The DESI Survey Validation: Results from Visual Inspection of Bright Galaxies, Luminous Red Galaxies, and Emission-line Galaxies

The Dark Energy Spectroscopic Instrument (DESI) Survey has obtained a set of spectroscopic measurements of galaxies to validate the final survey design and target selections. To assist in these tasks, we visually inspect DESI spectra of approximately 2500 bright galaxies, 3500 luminous red galaxies (LRGs), and 10,000 emission-line galaxies (ELGs) to obtain robust redshift identifications. We then utilize the visually inspected redshift information to characterize the performance of the DESI operation. Based on the visual inspection (VI) catalogs, our results show that the final survey design yields samples of bright galaxies, LRGs, and ELGs with purity greater than 99%. Moreover, we demonstrate that the precision of the redshift measurements is approximately 10 km s –1 for bright galaxies and ELGs and approximately 40 km s –1 for LRGs. The average redshift accuracy is within 10 km s –1 for the three types of galaxies. The VI process also helps improve the quality of the DESI data by identifying spurious spectral features introduced by the pipeline. Finally, we show examples of unexpected real astronomical objects, such as Ly α emitters and strong lensing candidates, identified by VI. These results demonstrate the importance and utility of visually inspecting data from incoming and upcoming surveys, especially during their early operation phases.

79 ASTRONOMY AND ASTROPHYSICS↗

Cape EGS: Frisco Pad Wells Flow Test Microseismic Data

This dataset contains microseismic data acquired during the Frisco pad flow test project led by Fervo Energy, conducted between July 17th - Aug 12th 2024, near the Utah FORGE geothermal site. The microseismic data was collected from various Utah FORGE wells: via Distributed Acoustic Sensing (DAS) fiber in 16B, and two 3-component geophones located in wells 56-32 and 78B. The dataset is structured in SEGY format, where the first six traces represent data from the geophones, and the remaining traces capture DAS data from well 16B. Each SEGY file in this dataset contains triggered microseismic events, with event initiation based on Short-Time Average over Long-Time Average (STA/LTA) detection criteria during the stimulation process. Files are grouped by time intervals and named following the structure "[WellPad][WellName][Month]_[Year]Divine_Trigger[EventNumber].sgy," indicating well pad, well name, date, and event number. Sampling parameters include a spatial sampling of approximately 2 meters for DAS channels and a temporal sampling rate of 2000 Hz, with each data record spanning 1.2 seconds. The files' coordinates are referenced to the location of the FORGE 16A-32 wellhead, positioned at UTM coordinates: Easting 334641.1891 m and Northing 4263443.693 m. The geographic coordinates for this origin are 38.50402147 latitude and -112.8963897 longitude, with an elevation of 1650.0249 meters above sea level.

15 GEOTHERMAL ENERGY↗

Cape EGS: Frisco 2-P Well Stimulation Microseismic Data

This dataset contains microseismic data acquired during the Frisco 2-P well stimulation project led by Fervo Energy, conducted between June 1 and June 11, 2024, near the Utah FORGE geothermal site. The microseismic data was collected from various Utah FORGE wells: via Distributed Acoustic Sensing (DAS) fiber in 16B, and three 3-component geophones located in wells 56-32, 78B, and 32. The dataset is structured in SEGY format, where the first nine traces represent data from the geophones, and the remaining traces capture DAS data from well 16B. Each SEGY file in this dataset contains triggered microseismic events, with event initiation based on Short-Time Average over Long-Time Average (STA/LTA) detection criteria during the stimulation process. Files are grouped by time intervals and named following the structure "[WellPad][WellName][Month]_[Year]Divine_Trigger[EventNumber].sgy," indicating well pad, well name, date, and event number. Sampling parameters include a spatial sampling of approximately 2 meters for DAS channels and a temporal sampling rate of 2000 Hz, with each data record spanning 1.2 seconds. The files' coordinates are referenced to the location of the FORGE 16A-32 wellhead, positioned at UTM coordinates: Easting 334641.1891 m and Northing 4263443.693 m. The geographic coordinates for this origin are 38.50402147 latitude and -112.8963897 longitude, with an elevation of 1650.0249 meters above sea level.

15 GEOTHERMAL ENERGY↗

Airfoil Computational Fluid Dynamics - 9k shapes, 2 AoA's

This dataset contains aerodynamic quantities - including flow field values (momentum, energy, and vorticity) and summary values (coefficients of lift, drag, and momentum) - for 8,996 airfoil shapes, computed using the HAM2D CFD (computational fluid dynamics) model. The airfoil shapes were designed using the separable shape tensor parameterization that encodes two-dimensional shapes as elements of the Grassmann manifold. This data-driven approach learns two independent spaces of parameter from a collection of sample airfoils. The first captures large-scale, linear perturbations, and the second defines small-scale, higher-order perturbations. For this data, we used the G2Aero database of over 19,000 airfoil shapes to learn a parameter space that captured a wide array of shape characteristics. We fixed the linear deformations to be the mean over the database and sampled new shapes over a four-dimensional parameter space of higher-order perturbation. This sampling approaches allows for isolated analysis of non-linear airfoil shape deformations while holding other aspects (e.g., airfoil thickness) approximately constant. The aerodynamic quantities for the generated airfoil were obtained using the HAM2D code, which is a finite-volume Reynolds-averaged Navier-Stokes (RANS) flow solver. We employ a fifth-order WENO scheme for spatial reconstruction with Roe's flux difference scheme for inviscid flux and second-order central differencing for viscous flux. A preconditioned GMRES method is applied for implicit integration. The Spalart-Allmaras 1-eq turbulence model is used for the turbulence closure, and the Medida-Baeder 2-eq transition model is applied to account for the effects of laminar turbulent transition. The airfoil grid is generated with a total of 400 points on the airfoil surface, the initial wall-normal spacing of y+ = 1, and an outer boundary located at 300 chord lengths away from the wall. The CFD simulations are performed at a freestream Mach number of 0.1, Reynolds number of 9M, and at two angles of attack, 4 deg. and 12 deg. The simulations were performed using the Bridges-2 system at the Pittsburgh Supercomputing Center in February 2023 as part of the INTEGRATE project funded by the Advanced Research Projects Agency - Energy in the U.S. Department of Energy. The data was collected, reformatted, and preprocessed for this OEDI submission in July 2023 under the Foundational AI for Wind Energy project funded by the U.S. Department of Energy Wind Energy Technologies Office. This dataset is intended to serve as a benchmark against which new artificial intelligence (AI) or machine learning (ML) tools may be tested. Baseline AI/ML methods for analyzing this dataset have been implemented, and a link to their repository containing those models has been provided. The .h5 data file structure can be found in the GitHub Repository resource under explore_airfoil_9k_data.ipynb.

9k↗