Search NASA⌕ Search

SEARCH · Search NASA

Results for “scale mixtures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Polar Bear™ – Innovative Capture of Storage Tank Vapors

Polar Bear™ is a patented technology developed by the Energy & Environmental Research Center (EERC) to capture storage tank vapors and eliminate methane emissions from upstream oil- and gas-producing facilities. Sparked by early commercial investment, the EERC licensed the technology and extended the intellectual property to storage tanks. Polar Bear™ is uniquely engineered and adapted to individual lower-producing facilities where there is otherwise no economic alternative for capturing tank vapors. A high number of small producing oil and gas wells are distributed across the country. The aggregate contributes to a significant volume of emissions. Because of the lack of economy of scale, gas volumes from these facilities are typically not recovered and contribute to methane emissions. Polar Bear™ provides a fit-for-purpose compression solution that addresses cost by reducing complexity with respect to conventional vapor recovery units and eliminating oil changes. Unique to Polar Bear™ is the capability to separate oxygenated gas from storage tank vapors. Storage tanks are designed to “breathe,” allowing gas to enter and escape during internal level and temperature changes. This infiltration of air into the tank headspace imparts undesirable oxygen content with respect to pipeline gathering. Polar Bear™ separates the vapor stream, allowing oxygen-rich gas to be used as fuel on-site while recovering the liquids-rich portion of the gas where oxygen content is minimized. A prototype system was tested to verify process models, evaluate operational performance, and advance the technology readiness level from 5 to 6. Results provide a good match between experimental measurements and process models, indicating the models are useful for future scale-up and field design. Various mixtures of nitrogen and liquefied petroleum gas were tested to understand the mass balance of nitrogen and how it relates to the potential control of oxygen content. Findings indicate that less than 2000 ppm of oxygen is likely to remain in the liquid portion of the gas in field applications. The research and development prepare the technology for field implementation to eliminate routine and fugitive methane emissions from storage tanks.

02 PETROLEUM↗
NASA NTRS1975

Space shuttle orbiter reaction control system jet interaction study

The space shuttle orbiter has forward mounted and rear mounted Reaction Control Systems (RCS) which are used for orbital maneuvering and also provide control during entry and abort maneuvers in the atmosphere. The effects of interaction between the RCS jets and the flow over the vehicle in the atmosphere are studied. Test data obtained in the NASA Langley Research Center 31 inch continuous flow hypersonic tunnel at a nominal Mach number of 10.3 is analyzed. The data were obtained with a 0.01 scale force model with aft mounted RCS nozzles mounted on the sting off of the force model balance. The plume simulations were accomplished primarily using air in a cold gas simulation through scaled nozzles, however, various cold gas mixtures of Helium and Argon were also tested. The effect of number of nozzles was tested as were limited tests of combined controls. The data show that RCS nozzle exit momentum ratio is the primary correlating parameter for effects where the plume impinges on an adjacent surface and mass flow ratio is the parameter where the plume interaction is primarily with the external stream. An analytic model of aft mounted RCS units was developed in which the total reaction control moments are the sum of thrust, impingement, interaction, and cross-coupling terms.

Rausch, J. R.↗
NASA NTRS1995

Mineralogic variations in fluvial sediments contaminated by mine tailings as determined from AVIRIS data, Coeur D'Alene River Valley, Idaho

The success of imaging spectrometry in mineralogic mapping of natural terrains indicates that the technology can also be used to assess the environmental impact of human activities in certain instances. Specifically, this paper describes an investigation into the use of data from the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) for mapping the spread of, and assessing changes in, the mineralogic character of tailings from a major silver and base metal mining district. The area under investigation is the Coeur d'Alene River Valley in northern Idaho. Mining has been going on in and around the towns of Kellogg and Wallace, Idaho since the 1880's. In the Kellogg-Smelterville Flats area, west of Kellogg, mine tailings were piled alongside the South Fork of the Coeur d'Alene River. Until the construction of tailings ponds in 1968 much of these waste materials were washed directly into the South Fork. The Kellogg-Smelterville area was declared an Environmental Protection Agency (EPA) Superfund site in 1983 and remediation efforts are currently underway. Recent studies have demonstrated that sediments in the Coeur d'Alene River and in the northern part of Lake Coeur d'Alene, into which the river flows, are highly enriched in Ag, Cu, Pb, Zn, Cd, Hg, As, and Sb. These trace metals have become aggregated in iron oxide and oxyhydroxide minerals and/or mineraloids. Reflectance spectra of iron-rich tailing materials are shown. Also shown are spectra of hematite and goethite. The broad bandwidth and long band center (near 1 micron) of the Fe(3+) crystal-field band of the iron-rich sediment samples combined with the lack of features on the Fe(3+) -O(2-) charge transfer absorption edge indicates that the ferric oxide and/or oxyhydroxide in these sediments is poorly crystalline to amorphous in character. Similar features are seen in poorly crystalline basaltic weathering products (e.g., palagonites). The problem of mapping and analyzing the downriver occurrences of iron rich tailings in the Coeur d'Alene (CDA) River Valley using remotely sensed data is complicated by the full vegetation cover present in the area. Because exposures of rock and soil were sparse, the data processing techniques used in this study were sensitive to detecting materials at subpixel scales. The methods used included spectral mixture analysis and a constrained energy minimization technique.

Farrand, W. H.↗
NASA NTRS1992

Quantitative subpixel spectral detection of targets in multispectral images

The conditions that affect the spectral detection of target materials at the subpixel scale are examined. Two levels of spectral mixture analysis for determining threshold detection limits of target materials in a spectral mixture are presented, the cases where the target is detected as: (1) a component of a spectral mixture (continuum threshold analysis) and (2) residuals (residual threshold analysis). The results of these two analyses are compared under various measurement conditions. The examples illustrate the general approach that can be used for evaluating the spectral detectability of terrestrial and planetary targets at the subpixel scale.

Sabol, Donald E., Jr.↗
NASA NTRS2021

Compact Augmented Spark Igniters for Liquid Rocket Engines

The objective of this dissertation is to characterize augmented spark impinging (torch) igniters. Torch igniters inject propellants into a small prechamber where a spark igniter imparts the activation energy to initiate combustion. The flame stabilizes within the prechamber and exits into the main combustion chamber where it ignites the main flow directly or by mixing with a coaxial flow to create a secondary flame. The underlying phenomena that promote reliable ignition are multifaceted and required a broad scope of investigations. Initial efforts focused on spark discharges across an annular geometry. Gaseous propellent projects the electrical arc toward the prechamber, where the arc and the thermal energy is imparted to the surrounding fluid then meets with a combustible mixture. Discharges are parametrically examined against pressure, spark-gap size, and exciter types to emulate transient engine startup. The energy imparted to the flow, approximate velocity, and distance traveled by the exhaust plume are determined. Spark quenching (no energy deposition) and its effects on perceived versus actual measurements are shown. Results outline the prechamber target zone where a combustible mixture is necessary for ignition. Next, three-dimensional, time-accurate, and nonreacting computational fluid dynamics simulations assess effects of geometric and mass flow differences on the size, location, and composition of a combustible mixture. Fluid dynamic phenomena are elucidated. Correlations between nondimensional variables are found. Results are coupled with a conservation-law analysis to produce novel objective functions. Lastly, a full-scale, modular torch igniter is tested. Injector sizes, mixture ratios, and injector momentum ratios are systematically varied to map ignition probability and ignition delay. Results show the importance of local mixture ratios, provide injector momentum ratios guidelines, and demonstrate reliable ignition of core mixture ratios typically outside flammability limits. The deliverable of this project is not a torch igniter or derivative thereof. Instead, this dissertation produces novel objective-functions for igniter design. These equations are functions of variables that may be constrained by engine-level requirements, physics, and experimental results from this work. They provide a foundation for future igniter design and will minimize iterative processes from the design cycle for next-generation ignition hardware.

Torch Igniter↗
DOE OSTI2026

Direct Simulations of H–He Mixtures at Planetary Interior Conditions: Demixing, Insulator–Metal Transition and Miscibility Boundaries

Accurate knowledge of the electrical and thermal conductivities and structural properties of hydrogen–helium mixtures under thermodynamic conditions within and beyond the immiscibility range is very important to predict the thermal evolution and internal structure of gas giant planets like Jupiter and Saturn. Here, we propose a novel method to determine the immiscibility boundary accurately without the need for free energy calculations, while providing consistent insights into structural and transport properties of mixtures. We show with direct large-scale ab initio simulations that the insulator–metal transition (IMT) of the hydrogen subsystem is strongly affected by an admixture with a small fraction of helium and occurs at temperatures significantly higher than those of pure hydrogen. At pressures below 150 GPa, the IMT boundary is not related anymore to the H 2 subsystem dissociation, the system remains insulating even after the full dissociation of H 2 molecules and its transition to an H–He mixture. The offset of the IMT in the H–He mixture relative to the dissociation region in the hydrogen subsystem and the significant reduction of static electrical and thermal conductivity by a factor between two and a few thousand relative to pure hydrogen found in mixtures have consequences for Jupiter and Saturn’s thermal evolution, internal structure, and dynamo action, affecting a large fraction of the interior of both planets.

Helium↗
DOE OSTI2024

Scale-Up Studies for the Dehydration of C 4+ Alcohols into Drop-In Diesel Fuel

Herein, we demonstrate the production of liter quantities of drop-in diesel-range ethers from biomass-derived alcohols. We report scale-up resultsfor the dehydration of a mixture of C 4+ alcohols using powder and pellet zeolite Ycatalyst in continuous flow and batch reactors. The activity of zeolite Y decreaseswith the introduction of an alumina binder. Large alcohols, as well as branchedand secondary alcohols, increase the coke content over the pellet Y catalyst. Thepellet formulation had lower carbon balances and selectivity to C 10+ ethers,suggesting that the pellet formulation increases alcohol absorption and cokeproduction. Crushing the pellet Y catalyst to smaller particle sizes does notrecover the activity of zeolite Y in its powder form. Cold flow experiments showthat particle agglomeration contributes to pressure buildup in the continuous flowreactor. C 10+ ether blends can be produced in batch reactors at high alcohol conversion regimes. One liter of a diesel #2 blend wasproduced by scaling up this reaction. The final blend consists of a substantial portion of C 10+ ethers (63.7 wt %), followed by heavyunknown products (27.4 wt %). Furthermore, the final alcohol and butyl ether concentration values were 7.3 and 1.5 wt %, respectively. Theblendstock reported in this paper can satisfy diesel #2 ASTM standards for density, cloud point, flashpoint, and cetane number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Use of Lignin-Based Admixture as Water Reducer (WRA) for Tailoring the Rheological Properties of Mortars for 3D-Printing

Efforts towards decarbonizing construction materials and industrial processes related to cement and concrete can be aided via multifaceted approaches that target alternative admixtures as well as precision control of fabrication. Chemical admixtures for water reduction have played a crucial role in the development of advanced mortar and concrete mixtures. Newer biomass processing techniques developed for aviation fuel production from corn stover biomass produce a highly reactive lignin byproduct that is suitable for chemical modifications to mimic the properties of commonly used polycarboxylate ethers (PCEs) with a smaller carbon footprint. These lignin-based plasticizers developed at NREL can be used in place of petrochemical-derived superplasticizers to tailor the rheological properties of cement-based systems for applications such as additive manufacturing while reducing the carbon intensity of the concrete mix. Lignosulfonates derived from paper pulping were historically used as water reducers only to be displaced with the rise of PCEs. The present study examines the use of a NREL produced lignin-based water reducing admixture (WRA), in cement pastes and mortar mixtures for 3D-printing at small- (mm) scale. The experimental program consisted of different formulations of oxidized lignin-based WRAs added in variable dosages to cement pastes with a fixed water-to-cement ratio. The objective is to achieve an appropriate workability, extrudability and buildability of mortar mixtures to produce 3D-printed specimens. The rheological characterization was performed to compare the initial yield stress and viscosity of the different mixtures with lignin-based admixture with respect to conventional PCE superplasticizers. The rheological characterization shows that the proposed material act as an effective water-reducer in cement systems, affecting the yield stress, plastic viscosity, and structuration rate of the mixtures evaluated. On the other hand, the effect on early hydration process of the cement pastes containing lignin-based admixtures is comparable to conventional superplasticizers.

3D-printing↗
NASA NTRS1992

Phase transformations in 40-60-GPa shocked gneisses from the Haughton Crater (Canada): An Analytical Transmission Electron Microscopy (ATEM) study

In order to better understand phase transformations, chemical migration, and isotopic disequilibrium in highly shocked rocks, we have performed a microprobe and an ATEM study on gneisses shocked up to 60 GPa from the Haughton Crater. This study reveals the following chemical and structural characteristics: (1) SiO2 dominant areas are formed by a mixture of pure SiO2 polycrystalline quartz identified by electron diffraction pattern and chemical analysis and a silica-rich amorphous phase containing minor amounts of aluminium, potassium, and iron; (2) Areas with biotitelike composition are formed by less than 200-nm grains of iron-rich spinels embedded in a silica-rich amorphous phase that is very similar to the one described above; (3) Layers with feldsparlike composition are constituted by 100-200-nm-sized alumina-rich grains (the indexation of the crystalline structure is under progress) and the silica-rich amorphous phase; (4) Zones characterized by the unusual Al/Si ratio close to 1 are formed by spinel grains (200-nm-sized) embedded in the same silica-rich amorphous phase; and (5) The fracturated sillimanites contain domains with a lamellar structure, defined by the intercalation of 100-nm-wide lamellae of mullite crystals and of a silica-rich amorphous phase. These mullite crystals preserved the crystallographical orientation of the preshock sillimanite. All compositional domains, identified at the microprobe scale, can thus be explained by a mixture in different proportion between the following phases: (1) a silica-rich amorphous phase, with minor Al and K; (2) quartz crystals; (3) spinel crystals and alumina-rich crystals; (4) sillimanite; and (5) mullite. Such mixtures of amorphous phases and crystals in different proportions explain disturbed isotope systems in these rocks and chemical heterogeneities observed on the microprobe.

Martinez, I.↗
DOE OSTI2025

Turbulent burning velocity of lean premixed hydrogen/air flames at engine conditions: Effects of turbulence intensity and length scale

For turbulent lean premixed hydrogen flames with strong thermodiffusively instabilities, most previous studies have focused on the influence of turbulence intensity, whereas the role of turbulence length scale is less well understood. Here, this study addresses this gap by conducting direct numerical simulations (DNS) of statistically planar turbulent premixed flames for a lean (ϕ=0.35) hydrogen/air mixture under independently varied turbulence intensity (u') and length scale (l T ) at engine-relevant thermodynamics conditions. Results show that as u' increases, the flame front becomes increasingly wrinkled, forming smaller cellular structures. In contrast, l T variations do not significantly alter the size of these structures. For the turbulent burning velocity (S T ), the normalized S T (i.e., S T /S L , where S L is the laminar flame speed) increases linearly with u', driven by both enhanced flame surface wrinkling (i.e., increased A T /A L ) and enhanced local burning rate (i.e., increased I 0 ). However, increasing l T reduces I 0 , despite a continued increase in A T /A L , resulting in only a marginal increase in S T /S L . To reveal the underlying mechanisms, especially the decreasing trend of I 0 with l T , local flame dynamics analyses are performed. It is found that as l T increases, the interaction between thermodiffusive effects and turbulence weakens due to the reduced tangential strain rate, while the flame curvature remains largely unchanged. This suppresses local reactivity enhancement and thus decreases I 0 , In contrast, an increase in u' enhances the interaction by amplifying both curvature fluctuation and tangential strain rate, leading to increased local reactivity (increased I 0 ). Finally, based on the DNS data, several new scaling models are proposed for the three global properties, S T /S L , A T /A L , and I 0 , and showed improvements compared to existing models. These findings provide new insights into the flame-turbulence interactions in thermodiffusively unstable hydrogen flames. The DNS dataset is also useful for the development of turbulent combustion models applicable to practical engine simulations.

Engine-relevant condition↗
DOE OSTI2025

LABQ3: Bayesian method for quantification of mineral compositions and nano-scale elemental mapping of 3D synchrotron XCT data

Quantitative analysis of mineral compositions is essential in understanding geochemical, mineralogical and environmental processes. Fine-resolution 3D imaging is widely done using synchrotron X-ray computed tomography (XCT), but existing analyses are limited to visualization and segmentation. This paper presents a new method, Linear Attenuation Bayesian Quantitative 3D-mapper (LABQ3), based on the linearity of X-ray attenuation with respect to elemental concentrations. To address the random variability in attenuation measurements, LABQ3 employs Bayesian decision theory to minimize classification error, using reference attenuation distributions from scans of pure mineral standards. To demonstrate LABQ3 and test its performance, we studied precipitated carbonate samples. XCT scans were done at multiple energies using the transmission X-ray microscope (TXM) at beamline 32-ID-C of the Advanced Photon Source at Argonne National Laboratory. The reconstructed 3D images have a voxel size of 20 nm. Analyses revealed rich nano-scale compositional heterogeneity within individual particles. A mixture of calcium and cadmium produced an overall stoichiometric composition of (Ca 0.78 ,Cd 0.22 )CO 3 , with some voxels containing nearly pure CdCO 3 . The addition of zinc led to an overall stoichiometric composition of 33% Ca, 28% Cd, 39% Zn, with a nearly pure CaCO 3 core and compositional zonation through the rim. These compositional gradients are related to temporal sequences of carbonate mineral formation where Cd precipitated at the beginning in (Ca,Cd)CO 3 , while Cd and Zn precipitated at the end in (Ca, Cd,Zn)CO 3 . Results differ from bulk analyses using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS), showing that LABQ3 provides particle-specific insights. LABQ3 distinguishes itself by quantifying chemical compositions along a continuum, making it different from XCT analyses based on segmentation. LABQ3 allows simultaneous acquisition of morphology and chemical composition in 3D, facilitating the interpretation of chemical gradients of trace elements, quantification of solid solution compositions, inferences about temporal sequences of mineral precipitation, and addressing other concerns about solid-phase chemistry.

58 GEOSCIENCES↗
NASA NTRS1985

Quantitative analysis of planetary reflectance spectra with principal components analysis

A technique is presented for quantitative analysis of planetary reflectance spectra as mixtures of particles on microscopic and macroscopic scales using principal components analysis. This technique allows for determination of the endmembers being mixed, their abundance, and the scale of mixing, as well as other physical parameters. Eighteen lunar telescopic reflectance spectra of the Copernicus crater region, from 600 nm to 1800 nm in wavelength, are modeled in terms of five likely endmembers: mare basalt, mature mare soil, anorthosite, mature highland soil, and clinopyroxene. These endmembers were chosen from a similar analysis of 92 lunar soil and rock samples. The models fit the data to within 2 percent rms. It is found that the goodness of fit is marginally better for intimate mixing over macroscopic mixing.

Johnson, P. E.↗
NASA NTRSDate not supplied

Development of New Lunar Highland Regolith Simulant, NUW-LHT-5M

Introduction: NASA has a need for large quantities of lunar simulants that closely match future manned lunar missions at landing sites near the Lunar South Pole. The current simulant was designed to approximate NU-LHT-2M, and -4M, except using natural minerals and a fully synthetic, non-basaltic, high calcium glass. Washington Mills in Niagara Falls, NY was contracted to produce this new simulant due to their electric arc furnace (EAF) fusion technology and capabilities for crushing and sizing ceramics. The primary objectives of this work were: (1) to create a commercially produced simulant that contains a high fidelity, high calcium (An90+), low Mg/Fe glass without basaltic constituents; (2) to create a simulant that uses existing, terrestrially mined, and readily available minerals blended with a synthetic glass, and (3) accomplish objectives (1) and (2) using conventional processing methods capable of production levels that can meet substantial current and future demands of NASA projects. Another consideration was that highland simulants closest to meeting these requirements, NU-LHT-2M and -4M types, are out of production and largely out of stock. Design: The design chosen for development and production for this work is NU-LHT-2M, de-signed by Doug Stoeser and Douglas Rickman, which uses Stillwater anorthosite and norite rocks and synthetic glass. The composition targeted the average composition, glass content and particle size distribution of Apollo 16 samples [1]. The design utilizes two Stillwater minerals, anorthosite (37.7 wt.%), norite (17.6 wt.%), a commercially sourced olivine (4.7 wt.%), and a synthetic glass (40 wt.%). Processing: Stillwater rocks were hand collected and initially crushed by the USGS. Further crushing and milling was performed at Washing-ton Mills. For the glass, oxides were blended in the ap-propriate ratios, blended in a v-blender, and placed in a graphite lined, water cooled pot. The mixture was fused in Washington Mills’ pilot scale, 500 kW EAF. The molten glass was then poured into water and quenched to inhibit crystallization. Several pour/quench cycles were required to produce the total quantity of glass needed. Anorthosite, norite and olivine were milled together to the target particle size in a ball mill. The glass was ball milled separately. The complete simulant was produced by blending the milled materials. Particle size distribution, phase and chemical analyses of the materials was were per-formed at Washington Mills. Results: The glass composition was found to match the Apollo 16 oxide content average [1] quite well, with the exception of SiO2 and Fe2O3. The deviation of SiO2 and Fe2O3 from batched content was believed to be due to limitations inherent in the use of the arc furnace technique for these types of materials. A particle size distribution of the full simulant formulation closely matching the average for the Apollo 16 samples was also achieved. Fig. 1 shows the morphology of the final simulant particles. The size distribution is compared to the target in Fig. 2. Conclusions: A new lunar highlands type simulant containing a high-quality synthetic glass, closely matching an average composition of the Apollo 16 regolith was produced. Processing utilized easily scalable mineral and glass making methods.

simulant↗
NASA NTRS1989

Mass spectrometric observations of metal oxychlorides produced by oxidation-chlorination reactions

It was recently reported that Cr2O3-forming alloys show less corrosion resistance than Al2O3-forming alloys in Cl2/O2 mixtures, which is attributed to the formation of porous Cr2O3 scales and stable CrO2Cl2 vapor species. This paper reports the results of direct mass spectrometric observations with a high-pressure sampling mass spectrometer of these metal oxychlorides forming on the surfaces of Hastelloy S and Alloy 600 superalloys. Samples were preoxidized for 2 hrs at 900 C before the exposure to a O2/Ar gas mixture containing 1 percent Cl2. Results of X-ray diffraction showed scales containing Cr2O3 and NiCr2O4 on both alloys. After exposure to Cl2, large quantities of Cr2O2Cl2 were demonstrated for both alloys, indicating that this is a route for the breakdown of Cr2O3 scales. The Mo present in the Hastelloy S leads to more rapid attack by Cl2, resulting in the formation of MoO2Cl2.

Jacobson, N. S.↗
DOE OSTI2024

Autonomous hybrid optimization of a SiO 2 plasma etching mechanism

Computational modeling of plasma etching processes at the feature scale relevant to the fabrication of nanometer semiconductor devices is critically dependent on the reaction mechanism representing the physical processes occurring between plasma produced reactant fluxes and the surface, reaction probabilities, yields, rate coefficients, and threshold energies that characterize these processes. The increasing complexity of the structures being fabricated, new materials, and novel gas mixtures increase the complexity of the reaction mechanism used in feature scale models and increase the difficulty in developing the fundamental data required for the mechanism. This challenge is further exacerbated by the fact that acquiring these fundamental data through more complex computational models or experiments is often limited by cost, technical complexity, or inadequate models. In this paper, we discuss a method to automate the selection of fundamental data in a reduced reaction mechanism for feature scale plasma etching of SiO 2 using a fluorocarbon gas mixture by matching predictions of etch profiles to experimental data using a gradient descent (GD)/Nelder–Mead (NM) method hybrid optimization scheme. These methods produce a reaction mechanism that replicates the experimental training data as well as experimental data using related but different etch processes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sum-of-Fractions Method

Sum-of-fractions is a method intended to make sure a subcritical margin for aqueous solutions and slurries of fissionable isotopes exists. The method indicates that a system is subcritical if the sum of the ratios of the mass of each isotope (in a mixture) to its individual minimum subcritical mass limit is less than or equal to one. Historically, the basis of the sum-of-fractions has been derived from allowances given in the American National Standards Institute (ANSI)/ American Nuclear Society (ANS)-8.15-1981. However, the allowance was removed in ANSI/ANS-8.15-2014 due to a lack of technical basis. A methodology was developed to assess the validity of using the sum-of-fractions for water- or polyethylene-moderated systems for the following nuclides: 232U, 233U, 234U, 235U, 237Np, 236Pu, 238Pu, 239Pu, 240Pu, 241Pu, 242Pu, 241Am, 242mAm, 243Am, 242Cm, 243Cm, 244Cm, 245Cm, 246Cm, 247Cm, 249Cf, and 251Cf. The methodology uses available benchmark data for mixtures of 233U, 235U, and 239Pu to establish the calculational margin, and a mass limit reduction to establish the margin of subcriticality. Water- or polyethylene-moderated and -reflected mixtures containing the nuclides are evaluated with the code system, SCALE 6.2.4. Including the calculational margin, subcritical mass limits for each nuclide were computed for optimally water- or polyethylene-moderated and fully reflected systems. These masses were used to create nuclide mixtures in which the sum of the mass to subcritical mass limit ratios is one. The various nuclide mixtures were modeled over a range of moderation and demonstrate the keff does not exceed the calculational margin. For additional assurance of subcriticality, a significant mass reduction is applied to each computed minimum critical mass of the nuclides without adequate benchmark data consistent with the method in ANSI/ANS-8.15-2014.

criticality safety, Actinide↗
NASA NTRS1989

Effect of Propellant Flowrate and Purity on Carbon Deposition in LO2/Methane Gas Generators

The generation and deposition of carbon was studied in the Carbon Deposition Program using subscale hardware with LO2/Liquid Natural Gas (LNG) and LO2/Methane propellants at low mixture ratios. The purpose of the testing was to evaluate the effect of methane purity and full scale injection density on carbon deposition. The LO2/LNG gas generator/preburner testing was performed at mixture ratios between 0.24 and 0.58 and chamber pressures from 5.8 to 9.4 MPa (840 to 1370 psia). A total of seven 200 second duration tests were performed. The LNG testing occurred at low injection densities, similar to the previous LO2/RP-1, LO2/propane, and LO2/methane testing performed on the carbon deposition program. The current LO2/methane test series occurred at an injection density factor of approximately 10 times higher than the previous testing. The high injection density LO2/methane testing was performed at mixture ratios between from 0.23 to 0.81 and chamber pressures from 6.4 to 15.2 MPa (925 to 2210 psia). A total of nine high injection density tests were performed. The testing performed demonstrated that low purity methane (LNG) did not produce any detectable change in carbon deposition when compared to pure methane. In addition, the C* performance and the combustion gas temperatures measured were similar to those obtained for pure methane. Similar results were obtained testing pure methane at higher propellant injection densities with coarse injector elements.

Bossard, J. A.↗