Search NASA⌕ Search

SEARCH · Search NASA

Results for “separation membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Membrane Separation of Gases From The Martian Atmosphere

A test bed has been constructed to test membrane modules for separation of gases under temperature and pressure conditions normally encountered on the surface of Mars. The test bed allows independent control of (1) feed flow rates, (2) feed composition, (3) feed pressure, (4) permeate pressure, and (5) operating temperature. Preliminary data obtained at a nominal feed pressure of 760 torr and permeate pressure of 10 torr has demonstrated the ability of one membrane module to operate at temperatures as low as -70 C. At temperatures below -40 C, however, significant loss of carbon dioxide and argon was observed, probably indicating condensation at the relatively high pressure used. As expected, permeation flow rates decreased with decreasing temperature, the flow at -30 C approximately 37% of the value at +23 C. Values of permeability for individual gas components showed similar decreases with decreasing temperature, but permeability ratios changed significantly. For example, the ratio of the permeabilities of carbon dioxide and nitrogen increased from 2.6 at 23 C to 5.6 at -30 C. Additional data at lower operating pressures and temperatures must be obtained in order to optimize design of a usable separation system.

Jennings, Paul A.↗
NASA NTRS2002

Membrane Separation of Gases from the Martian Atmosphere

A test bed has been constructed to test membrane modules for separation of gases under temperature and pressure conditions normally encountered on the surface of Mars. The test bed allows independent control of: (1) feed flow rates, (2) feed composition, (3) feed pressure, (4) permeate pressure, and (5) operating temperature. Preliminary data obtained at a nominal feed pressure of 760 torr and permeate pressure of 10 torr has demonstrated the ability of one membrane module to operate at temperatures as low as -70 C. At temperatures below -40 C, however, significant loss of carbon dioxide and argon was observed, probably indicating condensation at the relatively high pressure used. As expected, permeation flow rates decreased with decreasing temperature, the flow at -30 C approximately 37% of the value at +23 C. Values of permeability for individual gas components showed similar decreases with decreasing temperature, but permeability ratios changed significantly. For example, the ratio of the permeabilities of carbon dioxide and nitrogen increased from 2.6 at 23 C to 5.6 at -30 C. Additional data at lower operating pressures and temperatures must be obtained in order to optimize design of a usable separation system.

Jennings, Paul A.↗
DOE OSTI2022

Fabrication and accelerated long-term stability test of asymmetrical hollow fiber-supported thin film oxygen separation membrane

Asymmetrical hollow fiber-supported thin film membrane may provide microstructural advantages for air separation and oxygen production. The fabrication of such a membrane is usually very difficult, particularly the sintering behaviors and thermal expansion coefficient (TEC) mismatch among multiple layers. This directly affects the reliability and long-term stability of the membrane. Here, in this research, the sintering behaviors of a set of simple oxides are systematically studied and ZnO is identified as a material component for composite substrate La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF)-ZnO. The LSCF-ZnO ratios are further optimized by trading off several factors, e.g., matching the sintering behaviors and TECs of the LSCF-ZnO composite with those of LSCF thin film separation layer while enhancing the substrate strength. With the identified LSCF-ZnO ratio, the LSCF-ZnO composite hollow fiber substrate precursor is formed through slurry spinning process with porous microstructure being formed via phase inversion process. The thin film LSCF dense separation layer is then dip-coated on the substrate followed by co-sintering process. A thin, porous PrBaCo(Fe 0.6 Zr 0.2 Y 0.2 )O 5+δ (PBCFZY) catalyst layer is fabricated on the dense LSCF separation layer with dip-coating and sintering process, forming an asymmetrical membrane device LSCF-ZnO/LSCF/PBCFZY. Oxygen permeation test of the device is systematically conducted, and the fundamental mechanisms are analyzed. An accelerated long-term stability test of the membrane is also conducted (~550h, 46 thermal cycling loads), demonstrating excellent robustness and durability. The device is characterized and analyzed before and after the test. By replacing a considerable amount of high cost LSCF with low cost ZnO in the substrate, it not only enhances the stability but also reduces the capital cost of the membrane for practical applications.

42 ENGINEERING↗
DOE OSTI2020

Ion-gated carbon molecular sieve gas separation membranes

Membrane technology lies at the heart of many industrial gas separation processes and applications. Molecular sieving membranes that break the Robeson limit are desirable for energy-efficient gas separation. In this paper, we report a facile strategy of directly integrating ionic liquids (ILs) into porous membranes. Particularly, the ILs form an ultra-thin layer on the carbon molecular sieve (CMS) membranes rather than penetrating into the pores, acting as a smart gate for gas entry to boost the selectivity. The hybrid membrane exhibits CO 2 permeability >600 barrer and enhanced CO 2 /N 2 selectivity >50, which surpasses the Robeson limit and shows potential in CO 2 /N 2 separation process. Molecular dynamics simulations confirm the gating effect of the IL layer of molecular thickness. In conclusion, this work demonstrates a universal strategy to improve CMS membrane performance by creating an IL-membrane interface and tuning the ion-pore interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

High temperature steam separation membrane

Ceramic proton-conducting oxide membranes are described herein, which are useful for separating steam from organic chemicals under process conditions. The membranes have a layered structure, with a dense film of the perovskite over a porous composite substrate comprising the perovskite material and a metallic material (e.g., Ni, Cu, or Pt). The perovskite comprises an ABO 3 -type structure, where “A” is Ba and “B” is a specified combination of Ce, Zr, and Y. The perovskite ceramic materials described herein have an empirical formula of Ba(Ce x Zr 1-x-n Y n )O 3-δ , wherein 0<x<0.8 (e.g., 0.1≤x≤0.7 or 0.2≤x≤0.5); and 0.05≤n≤0.2; and δ=n/2. In some embodiments n is about 0.2. In some other embodiments 0.6≤x≤0.8; and n is about 0.2, such as Ba(Ce 0.7 Zr 0.1 Y 0.2 )O 3-δ , also referred to herein as BCZY712.

Lee, Tae H.↗
DOE OSTI2020

A Performance analysis of the Claridge-Culp-Liu dehumidification process: A novel approach for drying moist air based on membrane separation, vacuum compression and sub-atmospheric condensation

This article covers a basic model for analyzing the performance of the Claridge-Culp-Liu dehumidification process. The fundamental process efficiency limit for dehumidification is close to COP Carnot , but for the eight dehumidification cases examined, the limiting or ideal energy use required is 26% to 56% that of a Carnot condensing system as shown in an earlier paper. The model presented in this paper is used to show the membrane system performance reduction caused by finite membrane area, finite water vapor permeance, non-zero air permeance, non-zero system air pressure drop, non-ideal compressors, vacuum pumps, and condensers. The performance of a “conservative” membrane system based on the use of existing components is computed for eight specific conditions along with that of a “target” system that assumes expected component performance after additional future component development. The “conservative” membrane system would use 36% to 66% as much energy as a system with a COP=7 chiller to produce the same dehumidification for the eight cases examined while the “target” system would use 15% to 40% the energy of a system with a COP=7 chiller. In addition to the significant energy reduction over conventional technology, the membrane system offers the advantages of: 1) no HFC refrigerant use; 2) direct isothermal control over humidity ratio setpoint; 3) maximum capacity occurs at design conditions; and 4) system generates pure water extracted from air as a by-product.

42 ENGINEERING↗
DOE OSTI2022

Molten hydroxide membrane for separation of acid gases from emissions

In one embodiment, a separation membrane includes: a porous support structure, wherein the porous support structure comprises a system of continuous pores connecting an inlet of the separation membrane to an outlet of the separation membrane; and at least one alkali metal hydroxide disposed within pores of the porous support structure. Other aspects and embodiments of the disclosed inventive concepts will become apparent from the detailed description, which, when taken in conjunction with the drawings, illustrate by way of example the principles of the invention.

Worsley, Marcus↗
NASA NTRS2002

Membrane Separation Processes at Low Temperatures

The primary focus of Kennedy Space Center's gas separation activities has been for carbon dioxide, nitrogen, and argon used in oxygen production technologies for Martian in-situ resource utilization (ISRU) projects. Recently, these studies were expanded to include oxygen for regenerative life support systems. Since commercial membrane systems have been developed for separation of carbon dioxide, nitrogen, and oxygen, initially the studies focused on these membrane systems, but at lower operating temperatures and pressures. Current investigations art examining immobilized liquids and solid sorbents that have the potential for higher selectivity and lower operating temperatures. The gas separation studies reported here use hollow fiber membranes to separate carbon dioxide, nitrogen, and argon in the temperature range from 230 to 300 K. Four commercial membrane materials were used to obtain data at low feed and permeate pressures. These data were used with a commercial solution-diffusion modeling tool to design a system to prepare a buffer gas from the byproduct of a process to capture Martian carbon dioxide. The system was designed to operate, at 230 K with a production rate 0.1 sLpm; Feed composition 30% CO2, 44% N2, and 26% Ar; Feed pressure 104 kPa (780); and Permeate pressure 1 kPa (6 torr); Product concentration 600 ppm CO2. This new system was compared with a similar system designed to operate at ambient temperatures (298 K). The systems described above, along with data, test apparatus, and models are presented.

Parrish, Clyde↗
DOE OSTI2021

Controlling and Optimizing Photoinduced Charge Transfer across Ultrathin Silica Separation Membrane with Embedded Molecular Wires for Artificial Photosynthesis

Ultrathin amorphous silica membranes with embedded organic molecular wires (oligo( p -phenylenevinylene), three aryl units) provide chemical separation of incompatible catalytic environments of CO 2 reduction and H 2 O oxidation while maintaining electronic and protonic coupling between them. For an efficient nanoscale artificial photosystem, important performance criteria are high rate and directionality of charge flow. Here, the visible-light-induced charge flow from an anchored Ru bipyridyl light absorber across the silica nanomembrane to Co 3 O 4 water oxidation catalyst is quantitatively evaluated by photocurrent measurements. Charge transfer rates increase linearly with wire density, with 5 nm -2 identified as an optimal target. Accurate measurement of wire and light absorber densities is accomplished by the polarized FT-IRRAS method. Guided by density functional theory (DFT) calculations, four wire derivatives featuring electron-donating (methoxy) and -withdrawing groups (sulfonate, perfluorophenyl) with highest occupied molecular orbital (HOMO) potentials ranging from 1.48 to 0.64 V vs NHE were synthesized and photocurrents evaluated. Charge transfer rates increase sharply with increasing driving force for hole transfer from the excited light absorber to the embedded wire, followed by a decrease as the HOMO potential of the wire moves beyond the Co 3 O 4 valence band level toward more negative values, pointing to an optimal wire HOMO potential around 1.3 V vs NHE. Comparison with photocurrents of samples without nanomembrane indicates that silica layers with optimized wires are able to approach undiminished electron flux at typical solar intensities. Combined with the established high proton conductivity and small-molecule blocking property, the charge transfer measurements demonstrate that oxidation and reduction catalysis can be efficiently integrated on the nanoscale under separation by an ultrathin silica membrane.

photocurrent measurements↗
DOE OSTI2023

PDMS ‐silica composite gas separation membranes by direct ink writing

Abstract Polydimethylsiloxane (PDMS)‐based membranes containing amine‐functionalized and unfunctionalized silica particles were fabricated via direct ink writing for CO 2 /N 2 gas separation. The printability of the inks was evaluated by rheological measurements, while spectroscopy, microscopy, thermal measurements, and mechanical testing were employed to characterize the printed membranes. The surface morphology of the membranes revealed the absence of voids, demonstrating their suitability for gas separation. The printed membranes also exhibited desirable thermal and mechanical properties (i.e., thermal degradation temperature of 518 °C and tensile strength as high as 1.178 MPa with 529% elongation). The PDMS‐based membranes generally displayed high permeability for CO 2 but slightly low selectivity for the CO 2 /N 2 gas pair. The best‐combined permeability‐selectivity performance of 8794 barrer and selectivity of 11.64 was demonstrated by the printed PDMS membrane containing no SiO 2 fillers. The inclusion of unfunctionalized SiO 2 particles generally increased the membrane's gas permeability but compromised the selectivity. In contrast, membranes with amine‐functionalized silica showed improved selectivity compared to membranes containing unfunctionalized silica. Overall, the performance and characteristics offered by the PDMS/silica composite membranes demonstrated the potential of 3D printing as an economical and sustainable fabrication approach to developing materials for carbon capture applications.

Gutierrez, Dianne B.↗
DOE OSTI2020

Functional lipid pairs as building blocks of phase-separated membranes

Biological membranes exhibit a great deal of compositional and phase heterogeneity due to hundreds of chemically distinct components. As a result, phase separation processes in cell membranes are extremely difficult to study, especially at the molecular level. It is currently believed that the lateral membrane heterogeneity and the formation of domains, or rafts, are driven by lipid–lipid and lipid–protein interactions. Nevertheless, the underlying mechanisms regulating membrane heterogeneity remain poorly understood. In the present work, we combine inelastic X-ray scattering with molecular dynamics simulations to provide direct evidence for the existence of strongly coupled transient lipid pairs. These lipid pairs manifest themselves experimentally through optical vibrational (a.k.a. phononic) modes observed in binary (1,2-dipalmitoyl- sn -glycero-3-phosphocholine [DPPC]–cholesterol) and ternary (DPPC–1,2-dioleoyl- sn -glycero-3-phosphocholine/1-palmitoyl-2-oleoyl-glycero-3-phosphocholine [DOPC/POPC]–cholesterol) systems. The existence of a phononic gap in these vibrational modes is a direct result of the finite size of patches formed by these lipid pairs. The observation of lipid pairs provides a spatial (subnanometer) and temporal (subnanosecond) window into the lipid–lipid interactions in complex mixtures of saturated/unsaturated lipids and cholesterol. Our findings represent a step toward understanding the lateral organization and dynamics of membrane domains using a well-validated probe with a high spatial and temporal resolution.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1993

Membrane Separation Of Nitrogen Tetroxide

Pilot plant reduces N2O4 content to one-hundredth of inlet value. Permeable-membrane process removes nitrogen tetroxide from stream of nitrogen or helium gas. Operates in conjunction with scrubbing process removing N2O4 from He or N2 after He or N2 used as gas blanket in N2O4-storage tank. First stage of separator divided into two steps for efficiency. Permeate from second step of first stage and residue from second stage returned to inlet of first stage. Each module contains spiral-wound interleaved permeable membranes and spacer sheets.

Castro, R. C.↗
DOE OSTI2020

Amorphous fluorinated copolymer gas separation membranes

Membranes having a permselective active layer of a copolymerized perfluorinated monomer and an non-fluorinated alkylvinylester monomer demonstrate superior selective permeability performance for separating gas mixtures compared to membranes of exclusively perfluorinated polymers. Preferred active layer compositions are copolymers of perfluoro-2,2-dimethyl-1,3 dioxole (PDD) copolymerized with an alkylvinyl ester such as vinyl acetate, and vinyl pivalate, and with alkylvinyl esters that are substantially hydrolyzed to provide copolymerized vinyl alcohol functionality. The membranes can have a thin, high diffusion rate, “gutter layer” of a fluorinated polymer highly permeable to nitrogen positioned between the active layer and a porous support layer. A novel copolymer effective in selectively permeable membranes is a copolymer of PDD and an alkylvinyl ester compound having the formula H2C═CHOC(O)R1 in which R1 is a linear or branched alkyl group of from 2 to 5 carbon atoms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Investigation of humidity control via membrane separation for advanced Extravehicular Mobility Unit (EMU) application

This paper describes the development of a membrane-based process for dehumidifying the Extravehicular Mobility Unit (EMU). The membrane process promises to be smaller, lighter, and more energy efficient than the other technologies for dehumidification. The dehydration membranes were tested for 90 days at conditions expected to be present in the EMU. The results of these tests indicate that membrane-based technology can effectively control humidity in the EMU.

Newbold, D. D.↗
DOE OSTI2020

Sulfonyl PIM–1: A diverse separation membrane with dilation resistance

A sulfone modified variant (soPIM–1) of the first polymer of intrinsic microporosity has been studied through molecular simulations to analyze its applicability for adsorption–based separations of diverse nonpolar, quadrupolar, and dipolar adsorbate species. Single component gas phase adsorption isotherms of each adsorbate are provided. Here, the adsorptive properties of soPIM–1 are reported from the application of two methods: (a) traditional grand canonical Monte Carlo (GCMC) simulations and (b) a combination of Monte Carlo and molecular dynamics (GCMC/MD) techniques, which accounts for sorption–induced polymer dynamics. The calculated isosteric heats of adsorption are compared to those from the parent PIM–1 structure and reveals increased CO2 affinity with relatively no change in hydrocarbon affinity. Moreover, to quantify soPIM–1's resistance to dilation the evolution of the microporous structure across the adsorption isotherm loading pressures has been evaluated. Relatedly, nonequilibrium MD simulations have been utilized to determine that soPIM–1 is approximately twice as stiff as PIM–1.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Model system studies with a phase separated membrane bioreactor

The operation and evaluation of a bioreactor designed for high intensity oxygen transfer in a microgravity environment is described. The reactor itself consists of a zero headspace liquid phase separated from the air supply by a long length of silicone rubber tubing through which the oxygen diffuses in and the carbon dioxide diffuses out. Mass transfer studies show that the oxygen is film diffusion controlled both externally and internally to the tubing and not by diffusion across the tube walls. Methods of upgrading the design to eliminate these resistances are proposed. Cell growth was obtained in the fermenter using Saccharomyces cerevisiae showing that this concept is capable of sustaining cell growth in the terrestial simulation.

Petersen, G. R.↗