Results for “shock events” — Page 3

DOE OSTI2026

Development of an ultrafast wide-field microscope for single-shot laser-driven shock and ablation studies

We build an ultrafast wide-field microscope that captures single-shot events at near-optical diffraction limit for time-resolved studies of ablation and shock compression. Here, we provide insights on how the imaging and spectroscopic modalities of our single-shot microscope are impacted by the depth of field of a microscope objective. At high spatial resolution, the depth of field can critically impede these experiments and novel strategies must be implemented to acquire high-quality optical micrographs at high throughput. Here, we highlight how custom lithography-prepared samples enable us to rectify optical artifacts that arise during sample motion. With a complete knowledge of how the mechanical and optical components couple together, we can then extract critical spatial and temporal features of our ablation and shock compression experiments. For example, during the ablation processes, we show that shock waves created in metal thin films form Newton’s interference rings, whose evolution can be recorded with picosecond temporal resolution and at near optical diffraction-limit resolution.

Ultrafast microscopy↗

DOE OSTI2021

Thermal Effects on Gas Pipelines

Irradiance from a nuclear weapon can be the source of heat on gas infrastructure. This exposure when sufficiently intense can result in failure. An estimation tool for this behavior is the object of this study. A lumped capacity technique is employed to estimate the system temperature rise. The temperature rise is related to three possible outcomes. Two of the outcomes are relatively certain failure and relatively certain lack of effect. A large range of exposures are assessed with the model, and a relatively small number of cases are in the uncertain range. This model is presented as a tool that can be used in conjunction with a structural assessment model to sensitivities to the overpressure and shock to screen potential outcomes from subject events .

02 PETROLEUM↗

DOE OSTI2022

Impulse Noise Sampling at 9965 - Armag

One detonation test was monitored for impulse noise at Thunder Range on November 6, 2020. The TNT equivalency for this shot was 100 lbs. Ground zero for this test was located at an open area of Range 7. The Armag, where MOW were remotely located, was just south of the east end of the TR shock tube The purpose of this sampling event was to characterize the noise attenuation provided by the Armag which will be used as the primary firing location in a future test series. To determine attenuation provided by the Armag, one sound level monitor was placed inside and a second monitor was placed outside the hardened structure at the same distance from ground zero. The Armag was located 1300 feet from ground zero. Essential personnel performing these tests were remotely located inside the Armag and wore hearing protection with a minimum NRR of 23. Members of the Workforce (MOW) who are exposed to noise levels above 140 dBC, regardless of hearing protection worn, are required to be enrolled into the SNL Hearing Conservation Program which includes audiometric testing, online training (HCP100) and wearing hearing protection.

42 ENGINEERING↗

DOE OSTI2026

Exploding Bridgewire (EBW) Detonators: An Example of Synergistic Multiphysics

Exploding bridgewire (EBW) detonators are highly temporally reproducible explosive devices that require the rapid discharge of a high‐voltage capacitance to operate and so are immune to most of the accidental hazards associated with traditional electric detonators. They have been demonstrated to be safe enough for use in high‐consequence explosive applications. Despite continued use for over 82 years, understanding the exact mechanism of operation has remained elusive. Various researchers have ascribed either deflagration‐to‐detonation (DDT) or shock‐to‐detonation (SDT) phenomena observed in other explosive events to explain the science behind the successful engineering; however, a rigorous justification has been absent. Previously, we have demonstrated a complex interaction in EBW detonators between large electrical currents, non‐equilibrium thermodynamic material states, plasma physics, powder compaction phenomena, shock physics, photochemistry, and rapid conventional explosive chemical reaction processes. Specifically, we have made progress in understanding the complex multiphysics that operates in these detonators and demonstrating that it is a serendipitous synergy between UV light emitted from the arc formed as the bridge is electrically exploded and the accompanying short‐duration shock transmitted into the explosive powder bed that allows these devices to function at practical capacitor sizes and charge voltages. This insight not only places the topic on a firmer scientific footing but potentially enables new approaches to safe detonator design.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Multi-Axis Resonant Plate Shock Testing Evaluation and Test Specification Development

Resonant plate testing is a shock test method that is frequently used to simulate pyroshock events in the laboratory. Recently, it was discovered that if the unit under test is installed at an off-center location, a tri-axial accelerometer would record a shock response in three directions and the resulting shock response spectra implied that the test may have qualified the component in three directions simultaneously. The purpose of this research project was to evaluate this idea of multi-axis shock testing to determine if it was truly a multi-axis shock environment and if such a test could be used as an equivalent component qualification test. A study was conducted using generic, additively manufactured components tested on a resonant plate, along with an investigation of plate motion to evaluate the component response to off- center plate excitation. The data obtained here along with the analytical simulations performed indicate that off-center resonant plate tests are actually not three-axis shock tests, but rather single axis shocks at an arbitrary angle dictated by the location of the unit under test on the plate. This conclusion is supported by the fact that only one vectored shock input is provided to the component in a resonant plate test. Thus, the output response is a coupled response of the transverse plate vibration and the rotational motion of the component on the plate. Additionally, a multi-axis shock test defined by three single axis test environments always results in a significant component over-test in one direction.

42 ENGINEERING↗

DOE OSTI2020

Multichannel Deconvolution of Vibrational Shock Signals: An Inverse Filtering Approach

When transporting critical systems of national security interest, out-of-the ordinary, impulsive events that can potentially be undetected and affect overall system performance are of great concern. Impulsive events that can occur are essentially pulse-like, transient signals of short duration that evolve from various phenomena. Here the event can be created by either the dropping of a test object, the system, subjecting it to a compact high-energy blow or being struck unintentionally during transit resulting in potential damage. The intensity and location of the strike can cause an inoperability condition that is unacceptable in a national security environment. Therefore, it is essential to detect, classify and localize damage of any test object subjected to an impulsive-event. This effort was targeted to evaluate the vibrational response of test objects that are subjected to “transport” shocks and roadway vibrations during shipping and handling. Any potential damage that could be inflicted during transportation must not only be detected, but also be evaluated to determine the operational readiness of a test object before and after transport. This event is a critical task that must be addressed as part of the Lawrence Livermore National Laboratory (LLNL) national security mission. The estimation of excitation signals from noisy data is termed the deconvolution problem in the signal processing literature. The deconvolution problem is based on recovering the input excitation signal from a system characterized by its impulse response sequence. Using this model of the system, an “inverse” representation or filter is developed to remove the system from the measured data and recover the input. Deconvolution techniques have existed for a long-time; however, transient deconvolution presents a few uncommon problems, since the signal has a finite-length time duration resulting in a limited amount of data containing information about the excitation process. The transient is wideband in the frequency domain relative to any measurement sensor implying that the smaller bandwidth sensor system “filters” the excitation eliminating some of its essential information for recovery. This fact, coupled with the filtering effect of the test object itself makes this excitation recovery (deconvolution) problem a challenge for signal processing.

42 ENGINEERING↗

DOE OSTI2021

Structural dynamics modeling of spent nuclear fuel during hypothetical package drop events

The response of spent nuclear fuel (SNF) to hypothetical package drop events is of particular interest in the scope of spent fuel storage and transportation because of the mechanical shock encountered in such scenarios. Previous testing and modeling by the U.S. Department of Energy has demonstrated that the shock and vibration environment of normal shipping and handling conditions (excluding package drop events) is relatively benign and does not challenge the integrity of spent nuclear fuel. Cask drop events are worth considering because SNF packages are required to withstand free drops onto unyielding surfaces as part of their licensing basis. The acceleration experienced during drop events can be orders of magnitude higher, and thus more advanced models are needed to encompass potential nonlinear behavior of the fuel, such as spacer grid buckling and rod-to-rod impact. This work describes a number of finite element models developed to calculate the response of spent nuclear fuel to various hypothetical drop events that have been validated by package and fuel assembly drop tests conducted in the last decade. Sensitivity of the model response to factors such as package drop orientation, secondary impacts, and irradiated material properties as well as their potential impacts to fuel cladding integrity, was also investigated. Cask drops are not expected as a regular occurrence during SNF transportation, but this work helps raise the understanding of SNF mechanical loads to the point of consistency with the package design requirements.

Kadooka, Kevin↗

DOE OSTI2022

Impact of late-time neutrino emission on the diffuse supernova neutrino background

In the absence of high-statistics supernova neutrino measurements, estimates of the diffuse supernova neutrino background (DSNB) hinge on the precision of simulations of core-collapse supernovae. Understanding the cooling phase of protoneutron star (PNS) evolution (≳ 1 s after core bounce) is crucial, since approximately 50% of the energy liberated by neutrinos is emitted during the cooling phase. We model the cooling phase with a hybrid method by combining the neutrino emission predicted by 3D hydrodynamic simulations with several cooling-phase estimates, including a novel two-parameter correlation depending on the final baryonic PNS mass and the time of shock revival. We find that the predicted DSNB event rate at Super-Kamiokande can vary by a factor of ~2–3 depending on the cooling-phase treatment. Here we also find that except for one cooling estimate, the range in predicted DSNB events is largely driven by the uncertainty in the neutrino mean energy. With a good understanding of the late-time neutrino emission, more precise DSNB estimates can be made for the next generation of DSNB searches.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2024

Review of the August 1972 and March 1989 (Allen) Space Weather Events: Can We Learn Anything New From Them?

Abstract Updated summaries of the August 1972 and March 1989 space weather events have been constructed. The features of these two events are compared to the Carrington 1859 event and a few other major space weather events. It is concluded that solar active regions release energy in a variety of forms (X‐rays, EUV photons, visible light, coronal mass ejection (CME) plasmas and fields) and they in turn can produce other energetic effects (solar energetic particles (SEPs), magnetic storms) in a variety of ways. It is clear that there is no strong one‐to‐one relationship between these various energy sinks. The energy is often distributed differently from one space weather event to the next. Concerning SEPs accelerated at interplanetary CME (ICME) shocks, it is concluded that the Fermi mechanism associated with quasi‐parallel shocks is relatively weak and that the gradient drift mechanism (electric fields) at quasi‐perpendicular shocks will produce harder spectra and higher fluxes. If the 4 August 1972 intrinsic magnetic cloud condition (southward interplanetary magnetic field instead of northward) and the interplanetary Sun to 1 au conditions were different, a 4 August 1972 magnetic storm and magnetospheric dawn‐to‐dusk electric fields substantially larger than the Carrington event would have occurred. Under these special interplanetary conditions, a Miyake et al. (2012), https://doi.org/10.1038/nature11123 ‐like extreme SEP event may have been formed. The long duration complex 1989 storm was probably greater than the Carrington storm in the sense that the total ring current particle energy was larger.

Tsurutani, Bruce T.↗

DOE OSTI2026

Energy Evolution from the Chromosphere to the Heliosphere in the 2021 October 28 Solar Eruption

We perform a detailed study of the energetics for a well-observed solar eruption and flare that occurred on 2021 October 28. This event included a GOES class X1.0 flare, a global extreme-UV (EUV) wave, and a coronal mass ejection (CME) that reached speeds of >2000 km s −1 . The event was observed from a variety of spacecraft in NASA’s Heliophysics System Observatory, including multiple missions near Earth, STEREO-A off the Sun-Earth line, and Solar Orbiter, near the Sun-Earth line at about 0.8 au. Using remote sensing, in situ observations, and in some cases scaling laws based on previous observations, we characterize the following quantities: free magnetic energy, energy in nonthermal electrons, energy in nonthermal ions, bolometric energy, energy deposited in the chromosphere, thermal energy radiated in the flare loops, energy dissipated by the EUV wave, CME kinetic and gravitational potential energy, CME energy flux in the heliosphere, and the energy partition in the CME shock. We find that the total energy released during the event is consistent with estimates of the pre-event stored magnetic energy, and the CME kinetic + potential energy dominates the energy partition.

solar coronal mass ejection shocks↗

DOE OSTI2025

Ion Acceleration in Fermi-LAT Behind-the-Limb Solar Flares: The Role of Coronal Shock Waves

Here, we investigate the relationship between the gamma-ray emission measured with Fermi-LAT and radio signatures of coronal shock waves in four behind-the-limb (BTL) solar flares. All events were associated with metric type II radio burst. Both start and end times of the radio bursts were synchronized with the gamma-ray emission. The type II bursts associated with the BTL gamma-ray flares had higher speeds and lower formation heights than those of an average sample. These findings support the notion that the highly relativistic ions that produce the gamma-rays in BTL flares are accelerated at CME-driven propagating coronal shock waves rather than in large-scale coronal loops.

Corona↗

DOE OSTI2022

Strong reconnection electric fields in shock-driven turbulence

Turbulent magnetic reconnection in a quasi-parallel shock under parameters relevant to the Earth's bow shock is investigated by means of a two-dimensional particle-in-cell simulation. The addressed aspects include the reconnection electric field, the reconnection rate, and the electron and the ion outflow speeds. In the shock transition region, many current sheets are generated in shock-driven turbulence, and electron-only reconnection and reconnection where both ions and electrons are involved can occur in those current sheets. The electron outflow speed in electron-only reconnection shows a positive correlation with the theoretical speed, which is close to the local electron Alfvén speed, and a strong convection electric field is generated by the large electron outflow. As a result, the reconnection electric field becomes much larger than those in the standard magnetopause or magnetotail reconnection. In shock-driven reconnection that involves ion dynamics, both electron outflows and ion outflows can reach of the order of 10 times the Alfvén speed in the X-line rest frame, leading to a reconnection electric field the same order as that in electron-only reconnection. An electron-only reconnection event observed by the magnetospheric multiscale mission downstream of a quasi-parallel shock is qualitatively similar to those in the simulation and shows that the outflow speed reaches approximately half the local electron Alfvén speed, supporting the simulation prediction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Demonstration of CFD to support the coupled analysis of a reactor pressure vessel subjected to pressurized thermal shock

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended duration or under accident condition. As one of the most significant components of a reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Aging degradation mechanisms (e.g. thermo-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary. The prediction of the temperature field is achieved by using computational fluid dynamics (CFD) simulation. In this report, a demonstration CFD standalone simulation is performed to support coupled analysis for Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS). The study use a simplified computational domain to represents a real RPV. The purpose of the study is to demonstrate the transient temperature response of RPV to ECC injection. The CFD model is built in a robust and efficient way for further coupled calculation. The next steps of this work, including the coupled thermal and tensor mechanics capabilities using Cardinal are expected to be complete by the end of FY21 for the demo problem. After this, into FY22, the capability will be demonstrated for a realistic RPV.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

Simulation and Analysis on Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS) under SBLOCA scenario by using Cardinal to support the fracture mechanics analyses

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended durations or under accident condition. As one of the most significant components of a Reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Ageing degradation mechanisms (e.g. thermos-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary. The multi-physics simulations are performed using Cardinal, a wrapping of the GPU-oriented spectral element Computational Fluid Dynamics (CFD) code NekRS and other multi-physics sub-modules within the MOOSE framework. Cardinal now fully supports MOOSE stochastic perturbations of NekRS models with varying boundary conditions, initial conditions, material properties, and any other quantity which is defined by a kernel (such as coefficients in a momentum source model). The implementation is designed in a flexible manner so that scalar values are sent from MOOSE into a user scratch space in NekRS, which can then be applied for any purpose within the NekRS case files (both on the host and device). When modeling PTS, several factors can impact the results significantly. In this report, the impacts of the geometry of the model, Reynolds number and buoyancy effect are investigated. Two geometry, i.e., a simplified model and a realistic RPV model, with both laminar and turbulent flow condition are adopted for the PTS simulation with and without buoyancy effect. The purpose of the investigation is to understand the impact of these factors on the prediction of temperature history of RPV. The accurate prediction on the temperature evolution, which will be exported to Grizzly code for further analyses on the progression of aging mechanisms and their effects on the integrity of RPV structures, is very crucial. Based on the understanding of these factors, a more sophisticated model is built to analysis the PTS under SBLOCA scenario. A literature survey is conducted to pick the SBLOCA scenario for the multi-physics simulation. The analysis helps to explain the form and the transformation of the cold plum when the ECC is activated under SBLOCA. This model can be can be applied to study the PTS effect for different RPV configurations. The results can help to assess structural component degradation for advanced reactors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Multi physics simulation on Reactor Pressure Vessel (RPV) subjected to Pressurized Thermal Shock (PTS) by using Cardinal

The structural components that comprise nuclear reactors and their supporting structures are subjected to harsh operating environments that can challenge their integrity, especially after exposure for extended durations or under accident condition. As one of the most significant components of a Reactor, the Reactor Pressure Vessel (RPV) is exposed to an aggressive environment during the operation time (e.g. more than 40 years). Ageing degradation mechanisms (e.g. thermo-fatigue) could grow initial defects up to a critical size, increasing the susceptibility to failure in the RPV. The conventional methods are mostly based on simple crack and structure geometries. Very limited studies consider the real conditions of the RPV subjected to a thermal shock due to a Loss of Coolant Accident (LOCA). During a LOCA event, the most severe conditions take place when the emergency core cooling (ECC) water is injected inside the cold legs filled initially with hotter water and/or steam. The rapid cooling of the down-comer and the internal RPV surface followed probably by re-pressurization of the RPV causes large temperature gradients and variation of pressure which induces thermal-mechanical stresses. In order to develop the model for integrity assessment of a reactor pressure vessel (RPV) subjected to pressurized thermal shock (PTS), a multi-physics simulation, which includes the thermo-hydraulic, thermo-mechanical and fracture mechanics analyses is necessary.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Standing Shock Regulates Sparks in Explosive Flows

Electric sparks and explosive flows have long been associated with each other. Flowing dust particles originate charge through contact electrification and separate based on inertia, resulting in strong electric fields supporting sparks. These sparks can cause explosions in dusty environments, especially those rich in carbon, such as coal mines and grain elevators. Recent observations of explosive events in nature and decompression experiments indicate that supersonic flows of explosions may alter the electrical discharge process. Shocks may suppress parts of the hierarchy of the discharge phenomena, such as leaders. In our decompression experiments, a shock tube ejects a flow of gas and particles into an expansion chamber. We imaged an illuminated plume from the decompression of a mixture of argon and < 100 mg of diamond particles. We also performed hydrodynamics simulations of the decompression event that provide insight into the conditions supporting the observed behavior. The sparks occur below the sharp boundary of a condensation cloud. These results agree closely with the Mach disk shock shape and height in the simulation. This represents direct evidence that the sparks are sculpted by the outflow. The spatial and temporal scale of the sparks transmit an impression of the shock tube flow, a connection that could enable novel instrumentation to diagnose currently inaccessible supersonic granular phenomena.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Creating and studying a scaled interplanetary coronal mass ejection

The Sun, being an active star, undergoes eruptions of magnetized plasma that reach the Earth and cause the aurorae near the poles. These eruptions, called coronal mass ejections (CMEs), send plasma and magnetic fields out into space. CMEs that reach planetary orbits are called interplanetary coronal mass ejections (ICMEs) and are a source of geomagnetic storms, which can cause major damage to our modern electrical systems with limited warning. To study ICME propagation, we devised a scaled experiment using the Big Red Ball (BRB) plasma containment device at the Wisconsin Plasma Physics Laboratory. These experiments inject a compact torus of plasma as an ICME through an ambient plasma inside the BRB, which acts as the interplanetary medium. Magnetic and temperature probes provide three-dimensional magnetic field information in time and space, as well as temperature and density as a function of time. Using this information, we can identify features in the compact torus that are consistent with those in real ICMEs. We also identify the shock, sheath, and ejecta similar to the structure of an ICME event. This experiment acts as a first step to providing information that can inform predictive models, which can give us time to shield our satellites and large electrical systems in the event that a powerful ICME were to strike.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Modeling Particle Acceleration and Release from Solar Eruptions

Determining the relative contribution of solar flares versus coronal mass ejections in large solar energetic particle (SEP) events is a long-standing problem. Flare-accelerated particles may travel through complex magnetic fields in the eruption region and escape into interplanetary space, thereby contributing to large SEP events. The process by which flare accelerated particles are released into the heliosphere is poorly understood and yet is critical to advancing our understanding of SEPs. In this work, we address the release problem by solving the focused transport equation in the context of a 2.5D ARMS magnetohydrodynamic simulation of a breakout coronal mass ejection (CME)/flare event. We find that particles accelerated by flare reconnection can be released into interplanetary space through interchange reconnection between closed and open field lines. These particles can contribute directly to SEP events and may become an important seed population for further acceleration by CME-driven shocks. Additionally, we find that the energetic particle fluxes in the inner heliosphere remain elevated for an extended period, allowing them to contribute to SEP acceleration by subsequent CMEs. This study represents the first direct particle modeling of how flare-accelerated particles can contribute to major SEP events.

79 ASTRONOMY AND ASTROPHYSICS↗