Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering preparation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Manufacture of dense sintered bodies containing silicon nitride

Sintered bodies containing 1-32.5 Si oxide and 1.5 wt.% SiC (Si oxide/SiC wt. ratio 3/2) are prepared and kept in a 10-3000 kg/2 sq. cm. N (g) atmosphere at 1500-2300 degrees, while simultaneously maintaining the CO (g) partial pressure around the body lower than the nitrogenation equil. pressure to give a dense sintered body. The prepared dense sintered body has high strength at high temperatures. Thus, SiC 40, oxide 30 and Si3N4 30 wt% were fired to a body which was kept in 1500 kg/sq. cm. N (g) for 20 h at 2000 degrees to give a dense sintered body having high bending strength at high temperatures.

Hirota, K.↗
DOE OSTI2025

Tribological behavior of spark plasma sintered Ti 3 SiC 2 MAX phase composites

Ti₃SiC₂ MAX phases are considered promising candidates for tribological applications; but, their low hardness (5-6 GPa) can lead to increased abrasive wear and higher wear rates. This study investigates the effect of incorporating hard SiC particles on microstructure, mechanical, and tribological behavior of Ti₃SiC₂-SiC-based MAX phase composites prepared using spark plasma sintering at 1400 °C, 40 MPa, 15-minute holding time. Phase and microstructural characterization of composites confirmed the formation of Ti₃SiC₂ MAX phase (90%) along with TiC as a minor phase (10%). For Ti₃SiC₂-SiC, homogeneous distribution of SiC grains within Ti₃SiC₂ matrix resulted in increased hardness from ~11.6 GPa to ~14.8 GPa; however, the flexural strength decreased from ~615 MPa to ~597 MPa due to coefficient of thermal expansion mismatch. Tribological behavior of Ti₃SiC₂-SiC MAX phase composites was assessed using unidirectional sliding ball-on-flat tests with a 52100 steel ball at different loads and a constant speed of 0.05 m/s. SiC reinforced composites exhibited a decreased friction coefficient from 0.39 to 0.29 and wear rates comparable to Ti₃SiC₂ (7-10×10⁻³ mm³/N·m). SEM and EDS analysis of the worn surfaces indicated material transfer from the steel ball counter body and its oxidation due to frictional heating, at lower loads (2N and 5N), whereas at higher load (10N), fracture of the transfer layer dominated, with the presence of microcracks, delamination, grain pull-outs, and wear debris. Improved mechanical properties and good adhesion of SiC with Ti₃SiC₂ matrix resulted in reduced microcracks and grain pull-outs, making Ti₃SiC₂-SiC/Steel tribo-pair more suitable for tribological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Facile Interfacial Reduction Suppresses Redox Chemical Expansion and Promotes the Polaronic to Ionic Transition in Mixed Conducting (Pr,Ce)O 2−δ Nanoparticles

Mixed ionic/electronic conductors (MIECs) are essential components of solid-state electrochemical devices, such as solid oxide fuel/electrolysis cells. For efficient performance, MIECs are typically nanostructured, to enhance the reaction kinetics. However, the effect of nanostructuring on MIEC chemo-mechanical coupling and transport properties, which also impact cell durability and efficiency, has not yet been well understood. Here, in this work, Pr 0.2 Ce 0.8 O 2−δ (PCO20) nanopowders were prepared by coprecipitation, then sintered in a modified dilatometer at three different temperatures (600, 725, and 850 °C) for microstructure evolution, resulting in three samples with different average particle sizes (23, 30, and 53 nm). The chemical strain and electronic/ionic conductivity were then measured simultaneously on stable nanostructures in four isotherms from 550 to 400 °C with steps in pO 2 (1 to 10 –4 atm O 2 ). A microcrystalline bar was prepared and measured for comparison. Particle size reduction led to a monotonically decreasing isothermal redox chemical strain, confirmed by in situ high-temperature, controlled-atmosphere XRD measurements. The corresponding conductivity measurements provided defect chemical insight into the particle size-dependent chemical expansion behavior. The significant weakening of the pO 2 dependence and decreased activation energy for electrical conduction with decreasing particle size indicated a decrease in the reduction enthalpy of PCO, shifting the transition from (Pr) polaronic to ionic behavior to higher pO 2 . STEM-EELS measurements confirmed the majority of Pr was reduced to 3+ in the nanoparticles, while Ce remained 4+. These results demonstrate suppression of deleterious chemical expansion and tailoring of the dominant charge carrier simply through controlling the particle size, providing insights for MIEC microstructural design.

ceria↗
NASA NTRS1991

Microstructure and magnetization of Y-Ba-Cu-O prepared by melt quenching, partial melting and doping

Y-Ba-Cu-O samples prepared by means of a variety of melt-based techniques exhibit high values for their magnetic properties compared with those of samples prepared by solid state sintering. These techniques include single-stage partial melting as well as melt quenching followed by a second heat treatment stage, and they have been applied to the stoichiometric 123 composition as well as to formulations containing excess yttrium or other dopants. The structure of these melt-based samples is highly aligned, and the magnetization readings exhibit large anisotropy. At 77 K and magnetic field intensities of about 2 kOe, diamagnetic susceptibilities as high as -14 x 10(exp -3) emu/g were obtained in the cases of melt-quenched samples and remanent magnetization values as high as 10 emu/g for samples prepared by partial melting.

Hojaji, Hamid↗
DOE OSTI2020

3D Ion-Conducting, Scalable, and Mechanically Reinforced Ceramic Film for High Voltage Solid-State Batteries

Concerning the safety aspects of Li+ ion batteries, an epoxy-reinforced thin ceramic film (ERTCF) is prepared by firing and sintering a slurry-casted composite powder film. The ERTCF is composed of Li + ion conduction channels and is made of high amounts of sintered ceramic Li 1+ x Ti 2-x Al x (PO 4 ) 3 (LATP) and epoxy polymer with enhanced mechanical properties for solid-state batteries. The two- and three-dimensional characterizations are conducted not only for showing continuous Li+ ion channels thorough LATP ceramic channels with over 10-4 S cm-1 of ionic conductivity but also to investigate small amounts of epoxy polymer with enhanced mechanical properties. Solid-state Li + ion cells are fabricated using the ERTCF and they show initial charge–discharge capacities of 139/133 mAh g -1 . Furthermore, the scope of the ERTCF is expanded to high-voltage (>8 V) solid-state Li + ion batteries through a bipolar stacked cell design. Hence, it is expected that the present investigation will significantly contribute in the preparation of the next generation reinforced thin ceramic film electrolytes for high-voltage solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

The Impact of Sintering Atmosphere and Temperature on the Phase Evolution of High Surface Area LSCF Prepared by In Situ Carbon Templating

The thermochemical stability of lanthanum strontium cobalt ferrite (LSCF) processed between 1000 °C–1200 °C via the in situ carbon templating method was studied. This method generates high surface area ceramics at traditional solid oxide fuel cell (SOFC) sintering temperatures by generating a carbon template in situ and subsequently removing the template by oxidation at 700 °C. Argon processed samples produced an amorphous carbon template, whereas nitrogen tended to form graphitic carbon. Prior to the oxidation step, nitrogen samples comprised larger La 2 O 3 crystallites (22–40 nm) compared to argon (9–17 nm). Upon oxidation, argon samples resulted in a pure LSCF phase with surface areas in the 21–29 m 2 ·g −1 range, whereas nitrogen samples contained significant impurities. This demonstrates that the size of La 2 O 3 crystallites formed during inert processing limited the ability to produce a pure LSCF phase. Symmetrical cells comprising nano-LSCF electrodes generated by the templating method were compared to cells sintered directly in air. Impedance results suggest that nano-LSCF cells and cells processed in air were dominated by interfacial charge transfer resistance and gas diffusion, respectively. The results map out conditions for preparing and integrating high surface area, nanostructured LSCF into SOFC electrodes at traditional sintering temperatures. Strategies for improving the interfacial resistance of nano-LSCF electrodes are discussed.

Muhoza, Sixbert P. (ORCID:0000000299864241)↗
DOE OSTI2022

Thermoelectric Performance of the 2D Bi 2 Si 2 Te 6 Semiconductor

Bi 2 Si 2 Te 6 , a 2D compound, is a direct band gap semiconductor with an optical band gap of 0.25 eV, and is a promising thermoelectric material. Single-phase Bi 2 Si 2 Te 6 is prepared by a scalable ball-milling and annealing process and the highly densified polycrystalline samples are prepared by spark plasma sintering. Bi 2 Si 2 Te 6 shows a p-type semiconductor transport behavior and exhibits an intrinsically low lattice thermal conductivity of ~0.48 Wm -1 K -1 (cross-plane) at 573 K. The first-principles density functional theory calculations indicate that such low lattice thermal conductivity is derived from the interactions between acoustic phonons and low-lying optical phonons, local vibrations of Bi, the low Debye temperature and strong anharmonicity result from the unique 2D crystal structure and metavalent bonding of Bi 2 Si 2 Te 6 . The Bi 2 Si 2 Te 6 exhibits an optimal figure of merit ZT of ~0.51 at 623 K, which can be further enhanced by the substitution of Bi with Pb. Pb doping leads to a large increase in power factor S 2 σ, from ~4.0 μWcm -1 K- 2 of Bi 2 Si 2 Te 6 to ~8.0 μWcm -1 K -2 of Bi 1.98 Pb 0.02 Si 2 Te 6 at 775 K, owing to the increase in carrier concentration. Moreover, Pb doping induces a further reduction in the lattice thermal conductivity to ~0.38 Wm -1 K -1 (cross-plane) at 623 K in Bi 1.98 Pb 0.02 Si 2 Te 6 ,. The simultaneous optimization of the power factor and lattice thermal conductivity achieves a peak ZT of ~0.90 at 723 K and a high average ZT of ~0.66 at 400–773 K in Bi 1.98 Pb 0.02 Si 2 Te 6 .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Preparation and characterization of multiphase ceramic designer waste forms

Abstract The long-term performance, or resistance to elemental release, is the defining characteristic of a nuclear waste form. In the case of multiphase ceramic waste forms, correlating the long-term performance of multiphase ceramic waste forms in the environment to accelerated chemical durability testing in the laboratory is non-trivial owing to their complex microstructures. The fabrication method, which in turn affects the microstructure, is further compounding when comparing multiphase ceramic waste forms. In this work, we propose a “designer waste form” prepared via spark plasma sintering to limit interaction between phases and grain growth during consolidation, leading to monolithic high-density waste forms, which can be used as reference materials for comparing the chemical durability of multiphase waste forms. Designer waste forms containing varying amounts of hollandite in the presence of zirconolite and pyrochlore in a fixed ratio were synthesized. The product consistency test (PCT) and vapor hydration test (VHT) were used to assess the leaching behavior. Samples were unaffected by the VHT after 1500 h. As measured by the PCT, the fractional Cs release decreased as the amount of hollandite increased. Elemental release from the zirconolite and pyrochlore phases did not appear to significantly contribute to the elemental release from the hollandite phase in the designer waste forms.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of a Kollidon 90F-PEG300-Glycerin Binder for PZT 95/5 Ceramic Processing

This SAND Report documents the development of organic binder system for PZT 95/5 consisting of Kollidon 90F, PEG300, and glycerin. Binders are a critical component in the manufacture of ceramic components. Low performing binders can result in poor yield and lower performance of ceramic components. This study sought to develop a well performing binder system for PZT 95/5 ceramics to support Ferroelectric Neutron Generator manufacturing. The study explored the glass transition temperature, powder compaction properties, green strengths, and thermal decomposition over a wide composition range. An optimal composition was found consisting of 1.3 wt.% Kollidon 90F, 0.5 wt.% PEG300, and 0.2 wt.% glycerin, and incorporating humidity conditioning . The results showed that the optimized binder exhibited improved compaction performance and enhanced green strength compared to a baseline binder and at lower loading. Further, sintered PZT 95/5 parts prepared using the optimized binder exhibited ~5% improved polarization performance without alteration to the microstructure.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Simultaneous Luminescence Pressure and Temperature Measurement System for Hypersonic Wind Tunnels

Surface pressures and temperatures are determined from visible emission brightness and green-to-red color ratioing of induced luminescence from a ceramic surface with an organic dye coating. A ceramic-dye matrix of porous silica ceramic with an adsorbed dye is developed for high-temperature pressure sensitivity and stability (up to 150 C). Induced luminescence may be excited using a broad range of incident radiation from visible blue light (488-nm wavelength) to the near ultraviolet (365 nm). Ceramic research models and test samples are fabricated using net-form slip-casting and sintering techniques. Methods of preparation and effects of adsorption film thickness on measurement sensitivity are discussed. With the present 8-bit imaging system a 10% pressure measurement uncertainty from 50 to 760 torr is estimated, with an improvement to 5% from 3 to 1500 torr with a 12-bit imaging system.

Buck, Gregory M.↗
NASA NTRS2018

Physical and Biological Properties of Cobalt- and Copper-Doped Calcium Phosphates as Bone Substitute Materials

Arthritis, osteoporosis, and other bone diseases and defects are common medical issues worldwide. By utilizing ceramic biomaterials as bone substitutes to treat these diseases, bone regeneration can be promoted and toxicity from the substitute material can be limited. Calcium phosphate (CaP) ceramics have become popular as bone substitutes due to their biocompatibility and similarity in composition to natural bone. The purpose of this research was to investigate the physical properties and biological responses of CaP-based bone substitutes, doped with metal ions. Some metal ions are present in natural bone in small amounts, and recent studies show they affect the biological responses of CaPs significantly. Dopants such as magnesium (Mg), strontium (Sr), silicon (Si) and iron (Fe) alter the phase composition, mechanical properties, osteogenesis and angiogenesis properties of CaPs, depending on their concentration and method of addition. In the present study, the effects of cobalt (Co) and copper (Cu) on the physical and biological properties of two main CaP materials, brushite cement (BrC) and tricalcium phosphate (TCP), have been investigated. Different concentrations of dopants in forms of oxide and/or chloride were selected and their effect on phase composition, sintering behavior, density, setting time, compressive strength and in vitro interaction with osteosarcoma and osteoblast cells were studied. Different techniques of sample preparation, challenges during cement preparation and compact sample pressing, sintering, and methods of dopant addition are discussed. The presence of Cu in tricalcium phosphate was found to increase thermal stability of the material and decrease the impact of sintering temperature on porosity. In addition, Cu caused a reduction in expression of inflammatory gene markers by human osteoblast cells and an increased expression at early time points due of osteoinductive markers.The addition of Cu and Co to brushite cement caused an increase in thermal stability of the material, and the addition of Cu caused significant increase in setting time. Small dopant amounts of Co caused decrease in setting time, but higher amounts caused an increase. In addition, Cu dopant in small amounts resulted in an increase of compressive strength. Both Cu and Co led to a decrease in expression of inflammatory gene markers by osteoblast and osteosarcoma cells respectively, and Cu also caused an increase in osteoinductive marker expression. Thus, these results indicate that Cu and Co have a positive impact on the physical, mechanical and biological properties of calcium phosphate biomaterials.

Cummings, Haley V.↗
DOE OSTI2020

Exploring the relationship between solvent-assisted ball milling, particle size, and sintering temperature in garnet-type solid electrolytes

Garnet-type solid electrolytes, such as Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO), are promising materials for solid-state batteries, but processing remains a challenge, in part due to the high sintering temperature required for densification. Additionally, this temperature can be lowered by decreasing the initial particle size via solvent-assisted ball milling, but the relationship between solvent choice, particle properties, sintering behavior, and ionic conductivity is not well understood. In this work, we systematically explore these parameters, showing that milling in commonly used protic solvents, such as alcohols, effectively decreases the particle size but results in lithium loss (through Li + /H + exchange) that leads to poor sintering. By contrast, milling in aprotic solvents with surfactant reduces the particle size to ~220 nm without lithium loss, enabling the fabrication of dense samples (5.1 g/cm 3 ) with good ionic conductivity (0.43 mS/cm at 25 °C) at a lower sintering temperature (1000 °C). We compare ionic conductivities and activation energies for samples prepared with different particle sizes and sintering temperatures and use multiphase-field simulations to identify the mass transport and microstructural mechanisms responsible for the observed sintering dependence on particle size. These results further clarify the relationship between processing parameters and performance and represent important progress toward overcoming fabrication challenges for these materials.

25 ENERGY STORAGE↗
NASA NTRS1980

The effect of preparation conditions on the structure and mechanical properties of reaction-sintered silicon nitride

The microstructure of reaction sintered silicon nitride (RSSN) was changed over a wide range by varying the grain density, grain size of the silicon starting powder, nitriding conditions, and by introducing artificial pores. The influence of single microstructural parameters on mechanical properties like room temperature strength, creep behavior, and resistance to thermal shock was investigated. The essential factors influencing these properties were found to be total porosity, pore size distribution, and the fractions of alpha and beta Si3N4. In view of high temperature engineering applications of RSSN, potentials for optimizing the material's properties by controlled processing are discussed.

Heinrich, J.↗
NASA NTRS1989

A comparative study of sintered and melt-grown recrystallized YBa2Cu3Ox

This paper compares the properties of yttrium barium cuprate bulk specimens prepared by means of solid-state sintering on one hand and of growth from a largely molten state on the other. The current paper focuses on magnetization measurements at 77 K which show specimens made by the latter method to have high remanence magnetization values.

Hojaji, Hamid↗
DOE OSTI2022

Manufacturing Bulk Nanocrystalline Al-3Mg Components Using Cryomilling and Spark Plasma Sintering

In the current study, pure aluminum (Al) powders were cryomilled with and without 3 wt.% pure magnesium (Mg) dopant for varying durations followed by spark plasma sintering (SPS) of powders to prepare bulk components with superior mechanical properties. The crystallite sizes were determined for powders and the bulk components by analyzing the X-ray diffraction (XRD) spectrum. The calculations indicated a reduction in crystallite size with the increase in the cryomilling duration. The results also showed a more significant decrease in the crystallite sizes for Al-3Mg samples than that of pure Al. The changes in the surface morphology of powders were characterized using scanning electron microscopy (SEM). The elemental mapping analysis at nanoscale was carried out using Energy-dispersive X-ray spectroscopy (EDX) in Scanning transmission electron microscopy (STEM). The mechanical properties of the bulk components were assessed using a Vickers Microhardness tester. The test results demonstrated an improvement in the hardness of Mg-doped components. Higher hardness values were also reported with an increase in the cryomilling duration. This article discusses the mechanisms for the reduction in crystallite size for pure Al and Al-3Mg and its subsequent impact on improving mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Tribological properties of PM212: A high-temperature, self-lubricating, powder metallurgy composite

This paper describes a research program to develop and evaluate a new high temperature, self-lubricating powder metallurgy composite, PM212. PM212 has the same composition as the plasma-sprayed coating, PS212, which contains 70 wt percent metal-bonded chromium carbide, 15 wt percent silver and 15 wt percent barium fluoride/calcium fluoride eutectic. The carbide acts as a wear resistant matrix and the silver and fluorides act as low and high temperature lubricants, respectively. The material is prepared by sequential cold press, cold isostatic pressing and sintering techniques. In this study, hemispherically tipped wear pins of PM212 were prepared and slid against superalloy disks at temperatures from 25 to 850 C in air in a pin-on-disk tribometer. Friction coefficients range from 0.29 to 0.38 and the wear of both the composite pins and superalloy disks was moderate to low in the 10(exp -5) to 10(exp -6) cubic mm/N-m range. Preliminary tests indicate that the material has a compressive strength of at least 130 MPa over the entire temperature range of 25 to 900 C. This material has promise for use as seal inserts, bushings, small inside diameter parts and other applications where plasma-sprayed coatings are impractical or too costly.

Dellacorte, Christopher↗
NASA NTRS1990

Tribological properties of PM212 - A high temperature, self-lubricating, powder metallurgy composite

This paper describes a research program to develop and evaluate a new high temperature, self-lubricating powder metallurgy composite, PM212. PM212 has the same composition as the plasma-sprayed coating, PS212, which contains 70 wt percent metal-bonded chromium carbide, 15 wt percent silver and 15 wt percent barium fluoride/calcium fluoride eutectic. The carbide acts as a wear resistant matrix and the silver and fluorides act as low and high temperature lubricants, respectively. The material is prepared by sequential cold press, cold isostatic pressing and sintering techniques. In this study, hemispherically tipped wear pins of PM212 were prepared and slid against superalloy disks at temperatures from 25 to 850 C in air in a pin-on-disk tribometer. Friction coefficients range from 0.29 to 0.38 and the wear of both the composite pins and superalloy disks was moderate to low in the 10(exp -5) to 10(exp -6) cubic mm/N-m range. Preliminary tests indicate that the material has a compressive strength of at least 130 MPa over the entire temperature range of 25 to 900 C. This material has promise for use as seal inserts, bushings, small inside diameter parts and other applications where plasma-sprayed coatings are impractical or too costly.

Dellacorte, Christopher↗