Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering preparation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Processing and properties of PSZT 95/5 ceramics with varying Ti and Nb substitution

Niobium doped lead-tin-zirconate-titanate ceramics near the PZT 95/5 orthorhombic AFE – rhombohedral FE morphotropic phase boundary Pb 1-0.5y (Zr 0.865-x Ti x Sn 0.135 ) 1-y Nb y O 3 were prepared according to a 2 2+1 factorial design with x = 0.05, 0.07 and y = 0.0155, 0.0195. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1250°C for 6 hours. All compositions were ~98% dense with no detectable secondary phases by XRD. The ceramics exhibited equiaxed grains with intergranular porosity and grain size was ~5 μm, decreasing with niobium substitution. Compositions exhibited remnant polarization values of ~32 μC/cm 2 , increasing with Ti substitution. Depolarization by the hydrostatic pressure induced FE-AFE phase transition was drastically affected by variation of the Ti and Nb substitution, increasing at a rate of 113 MPa / 1% Ti and 21 MPa / 1% Nb. Total depolarization output was insensitive to the change in Ti and Nb substitution, ~32.8 μC/cm 2 for the PSZT ceramics. The R3c-R3m and R3m-Pm3m phase transition temperatures on heating ranged from 90 to 105°C and 183 to 191°C, respectively. Ti substitution stabilized the R3c and R3m phases to higher temperatures, while Nb substitution stabilized the Pm3m phase to lower temperatures. Thermal hysteresis of the phase transitions was also observed in the ceramics, with transition temperature on cooling being as much as 10°C lower.

36 MATERIALS SCIENCE↗
DOE OSTI2021

3D printed Ni-Mn-Fe Bi-Functional Catalyst for Metal Air Batteries

Oxygen evolution catalyst with porous structures on the submillimeter and millimeter ranges have been shown to have high catalytic activity. Often, a limiting factor in the performance of a catalyst can be its specific surface area as this can limit the availability of active sites which encourage the desired reaction. As such, the inclusion of a hierarchical structure that include both meso-scale and nano-scale porosity can offer a means to greatly increase the performance of electrochemical catalysts. We have developed a method for manufacturing samples with such a hierarchical structure by combining techniques of direct ink writing (DIW), thermal sintering and free corrosion based dealloying. This allows us to prepare three-dimensionally structured samples with open-cell porosity at the macro-, micro- and nano-scales. Each level of porosity offers a different advantage to the overall functionality and applicability of this technology.

25 ENERGY STORAGE↗
DOE OSTI2020

Revealing the Structural Evolution and Phase Transformation of O3-Type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 Cathode Material on Sintering and Cycling Processes

O-type layered oxide cathode materials can be easily synthesized for a full sodium stoichiometry with high specific capacity, but they all suffer from a capacity fade on cycling. The sintering process control and optimization are critical to ensure a high quality and consistency of the prepared cathode materials with stable structure. Herein, in situ high-energy X-ray diffraction (HEXRD) was first employed to investigate the phase evolution of the oxides during the sintering process of O3-type NaNi 1/3 Fe 1/3 Mn 1/3 O 2 . The in situ HEXRD and both operando Bragg coherent diffraction (BCXD) and coherent multicrystal diffraction (CMCD) were utilized to investigate the phase transformation of the cathode materials during the sodiation/desodiation process. A composite structure comprised of O-type and P-type oxides was formed after the initial electrochemical activation of the cathode material, resulting in good structural and electrochemical stability. This finding implies that strain engineering can be a new design philosophy for the development of next generation high-performance sodium ion cathodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Active and Stable PtPd Diesel Oxidation Catalysts under Industry‐Defined Test Protocols

Nanoparticle-supported Pt and Pd catalysts are employed industrially to convert CO and hydrocarbon residue from incomplete diesel fuel combustion into more environmentally-benign products. However, these catalysts deactivate over time due to sintering, especially for Pt nanoparticles which readily generate volatile species under high operating temperatures. Here, we turned the detrimental vapor-mediated sintering of Pt into an advantage by using a physical mixture of Pt and Pd catalysts prepared using a raspberry-colloid-templating (RCT) method. The RCT method produced Pt/Al 2 O 3 and Pd/Al 2 O 3 catalysts with partially embedded NPs to inhibit surface-mediated sintering pathways. As validated using an industry-defined emission control test protocol, aging a physical mixture of Pt/Al 2 O 3 and Pd/Al 2 O 3 at high temperature produced an alloyed PtPd/Al 2 O 3 catalyst that outperformed the fresh catalyst mixture and both individual catalysts for hydrocarbon conversion, while exhibiting high catalytic stability and resistance to sintering and to SO 2 poisoning. X-ray photoelectron spectroscopy revealed that in the aged catalyst mixture, half of the Pd content existed in the more active metallic state, compared to the less active oxide forms in the fresh mixture and both individual catalysts, explaining the unusual activity enhancement. Our results represent a practical approach to producing active and stable PtPd/Al 2 O 3 diesel oxidation catalysts for emission control applications.

Lim, Kang Rui Garrick [Harvard University, Cambrid↗
DOE OSTI2021

Persistent Structure and Frustrated Magnetism in High Entropy Rare-Earth Zirconates

The configurational complexity and distinct local atomic environments of high entropy oxides remain largely unexplored, leaving structure-property relationships and the hypothesis that the family offers rich tunability for applications ambiguous. This work investigates the influence of cation size and materials synthesis in determining the resulting structure and magnetic properties of a family of high entropy rare-earth zirconates (HEREZs, nominal composition RE 2 Zr 2 O 7 with RE = rare-earth element combinations including Eu, Gd, Tb, Dy, Ho, La, or Sc). Here, the structural characterization of the series is examined through synchrotron X-ray diffraction and pair distribution function analysis, and electron microscopy, demonstrating average defect-fluorite structures with considerable local disorder, in all samples. The surface morphology and particle sizes are found to vary significantly with preparation method, with irregular micron-sized particles formed by high temperature sintering routes, spherical nanoparticles resulting from chemical co-precipitation methods, and porous nanoparticle agglomerates resulting from polymer steric entrapment synthesis. In agreement with the disordered cation distribution found across all samples, magnetic measurements indicate that all synthesized HEREZs show frustrated magnetic behavior, as seen in a number of single-component RE 2 Zr 2 O 7 pyrochlore oxides. These findings advance the understanding of the local structure of high entropy oxides and demonstrate strategies for designing nanostructured morphologies in the class.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Synthesis and characteristics of porous ceramic tubes: a comparison of centrifugal casting and cold isostatic pressing methods

Short porous ceramic tubes in small quantities are needed for membrane-related research and development efforts and can be synthesized by centrifugal casting (CC) or cold isostatic pressing (CIP) methods. Here, this work evaluates the characteristics of porous ceramic tubes prepared by both methods and provides a strategy for selecting the proper method for ceramic tube fabrication, depending on its application. Samarium-doped ceria (SDC) with an average crystallite size of 10 nm was synthesized by a citrate method and used to make porous SDC tubes by the CC and CIP methods under different conditions. Porous SDC tubes were prepared from an aqueous suspension of the SDC powder with polyvinyl alcohol (PVA) using a cylindrical metallic mold, centrifugated at 4000–6000 rpm, followed by sintering in 1200–1500 °C. SDC tubes were also made by the CIP method from the SDC powder placed inside a cylindrical rubber bag followed by isostatic compression at 1379 bar. The pore structure of the SDC tubes was characterized by helium permeation and liquid nitrogen Archimedes method. Due to high compression pressure giving a low porosity green tube, the CIP method with lower sintering temperature produces SDC tubes with much lower porosity and average pore size and similar tortuosity compared to the CC methods. The CIP method should be used to prepare low porosity or dense ceramic tubes, and the CC method should be used for preparing high-porosity ceramic tubes or tubes with pore gradient tube wall.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Elastic moduli of high-density, sintered monoliths of yttrium dihydride

Yttrium dihydride has been considered as potential nuclear reactor moderator for micro-reactors operating in the thermal energy spectrum due to their ability to retain hydrogen to high temperatures while having a relatively low impact on neutron economy. Despite these advantages, it is difficult to prepare yttrium dihydride in high-density, near net-shape monoliths for moderator applications due to volume expansion upon hydriding and the pyrophoric nature of the material. In this work, high-density monoliths of yttrium dihydride were prepared by direct hydriding and using powder metallurgical methods. Resonant ultrasound spectroscopy was used to measure the elastic moduli of the sintered monoliths, while nanoindentation was used to determine the Young’s modulus and hardness of the directly-hydrided yttrium and the sintered monoliths. Single crystal elastic constants and related properties of yttrium dihydride were also determined using density functional theory (DFT) for comparison. We report mechanical properties of materials produced by both methods were observed to be consistent with the values from literature for yttrium dihydride. Due to the novelty of producing yttrium dihydride by powder metallurgy, this result indicated that the monoliths produced by powder metallurgy were of high quality. To that end, powder metallurgy is believed to be a viable method for large-scale production of yttrium dihydride monoliths for nuclear reactor moderator applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase stability and magnetic and electronic properties of a spark plasma sintered CoFe – P soft magnetic alloy

More efficient power conversion devices are able to transmit greater electrical power across larger distances to satisfy growing global electrical needs. A critical requirement to achieve more efficient power conversion are the soft magnetic materials used as core materials in transformers, inductors, and motors. To that effect it is well known that the use of non-equilibrium microstructures, which are, for example, nanocrystalline or consist of single phase solid solutions, can yield high saturation magnetic polarization and high electrical resistivity necessary for more efficient soft magnetic materials. In this work, we synthesized CoFe – P soft magnetic alloys containing nanocrystalline, single phase solid solution microstructures and studied the effect of a secondary intermetallic phase on the saturation magnetic polarization and electrical resistivity of the consolidated alloy. Single phase solid solution CoFe – P alloys were prepared through mechanically alloying metal powders and phase decomposition was observed after subsequent consolidation via spark plasma sintering (SPS) at various temperatures. The secondary intermetallic phase was identified as the orthorhombic (Co x Fe 1-x ) 2 P phase and the magnetic properties of the (Co x Fe 1-x ) 2 P intermetallic phase were found to be detrimental to the soft magnetic properties of the targeted CoFe – P alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reactive flash sintering and characterization of bulk high entropy nitrides

Over the past decade, numerous high-entropy ceramics have been synthesized, often displaying attractive properties. However, the study on facile preparation of bulk high entropy nitrides (HEN) are limited, despite its broad potential applications. This research demonstrates for the first time rapid fabrication (within ∼6 min) of bulk high-entropy nitrides, especially (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N, from binary nitride powder mixtures using a highly efficient reactive flash sintering (RFS) technique. X-ray diffraction (XRD) shows the HENs from RFS are near single-phase solid solutions with a rock salt crystal structure, while in situ synchrotron study carried out during RFS captured in real time the formation of HEN, which was preserved upon cooling, suggesting thermodynamic stability of the HEN phase, even up to extreme pressure (∼35.6 GPa). Microscopic analyses using SEM, STEM, and EDS reveal decent uniformity for HEN with no obvious segregation of elements, even to submicron scale. Some properties of the obtained bulk HENs are consistent with expectations. For example, their hardness and bulk modulus are close to estimates based on rule-of-mixture (ROM) values from the constituent binary nitrides. Meanwhile, some other measured properties seem to show surprises. For example, the fracture toughness for the HENs (e.g., 7.81 ± 1.40 MPa•m 1/2 or higher) turns out to be more than double of the expected ROM estimates. The significantly improved fracture toughness is attributed to the observed nano-layered structure of the HENs, despite the HEN’s cubic crystal structure and high hardness. In addition, the oxidation resistance shows improvement up till ∼800°C, possibly due to Ta doping that suppress oxygen vacancy formation in the oxide shell, while the 5-metal HEN of (Al 0.17 Nb 0.17 Ta 0.17 Ti 0.32 Zr 0.17 )N displays superconductivity (T c of ∼5–7 K from magnetism and resistivity measurements, slightly lower than ROM estimate), despite insulating property of starting AlN. Furthermore, future study combining experimental investigation using larger samples to confirm the observed increase in fracture toughness and oxidation resistance, theoretical modeling at different length scale, and more detailed structural/chemical characterization, especially at the atomic scale, are all needed to fully understand the inter-relationships between composition, processing, structure, and novel properties for these HENs and the development of related new materials for different applications.

Flash sintering↗
DOE OSTI2021

Preparing Li-garnet electrodes with engineered structures by phase inversion and high shear compaction processes

We report solid-state lithium batteries are promising for safety and energy density com-pared with traditional lithium-ion batteries. However, the large interfacial resistance between the electrode and electrolyte is a bottleneck to achieving high-performance solid-state batteries. Engineered electrode structures with a porous scaffold of the solid electrolyte material are promising to lower the interfacial resistance and provide a mechanical support for a thin solid electrolyte layer. In this work, two ceramic processing techniques are used to fabricate porous/dense bilayer architectures based on a Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO) Li-garnet material. Finger-like vertically aligned pores are created by the phase inversion (PI) process. A water bath presaturated with Li salt prevents Li loss during the PI solvent exchange step. Pore size and porosity can be optimized by adjusting the bath temperature. The high shear compaction process was used to prepare LLZO tapes with 40, 60, and 80 vol% poreformer. The porosity of the tapes after sintering is 39.5%, 58.4%, and 75.4%, respectively. Microtomography exhibits the porosity, pore shape, and pore distribution of the tapes. A typical cathode material LiNi 0.33 Mn 0.33 Co 0.33 O 2 (NMC) is filled into the pores via vacuum infiltration, and a dense cathode layer is formed within the garnet scaffold.

25 ENERGY STORAGE↗
DOE OSTI2021

New Cost-Effective Halide Solid Electrolytes for All-Solid-State Batteries: Mechanochemically Prepared Fe 3+ -Substituted Li 2 ZrCl 6

Owing to the combined advantages of sulfide and oxide solid electrolytes (SEs), that is, mechanical sinterability and excellent (electro)chemical stability, recently emerging halide SEs such as Li 3 YCl 6 are considered to be a game changer for the development of all-solid-state batteries. However, the use of expensive central metals hinders their practical applicability. In this study, a new halide superionic conductors are reported that are free of rare-earth metals: hexagonal close-packed (hcp) Li 2 ZrCl 6 and Fe 3+ -substituted Li 2 ZrCl 6 , derived via a mechanochemical method. Conventional heat treatment yields cubic close-packed monoclinic Li 2 ZrCl 6 with a low Li + conductivity of 5.7 × 10 –6 S cm –1 at 30 °C. In contrast, hcp Li 2 ZrCl 6 with a high Li + conductivity of 4.0 × 10 –4 S cm –1 is derived via ball-milling. More importantly, the aliovalent substitution of Li 2 ZrCl 6 with Fe 3+ , which is probed by complementary analyses using X-ray diffraction, pair distribution function, X-ray absorption spectroscopy, and Raman spectroscopy measurements, drastically enhances the Li + conductivity up to ≈1 mS cm –1 for Li 2.25 Zr 0.75 Fe 0.25 Cl 6 . The superior interfacial stability when using Li 2+ x Zr 1– x Fe x Cl 6 , as compared to that when using conventional Li 6 PS 5 Cl, is proved. Furthermore, an excellent electrochemical performance of the all-solid-state batteries is achieved via the combination of Li 2 ZrCl 6 and single-crystalline LiNi 0.88 Co 0.11 Al 0.01 O 2 .

25 ENERGY STORAGE↗
DOE OSTI2020

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

ABSTRACT Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp, and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m 1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m 1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m 1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO 2 , the crack deflection and bridging of SiCp and SiCw, and the pull‐out of SiCw.

Liu, Longyang↗
DOE OSTI2020

Aluminum-doped U 3 Si 2 composite fuels with enhanced oxidation resistance

Al-doped U 3 Si 2 composite fuels with controlled microstructure were fabricated by spark plasma sintering that display greatly-improved oxidation resistance as compared with monolithic and Al-doped silicides prepared by standard powder metallurgy or arc melting. The effects of Al additives on the thermal-mechanical properties and oxidation resisance of the micron- and nano-sized U 3 Si 2 composites were investigated. Additionally, a minimal addition of 1.8 at% Al is effective to increase the onset oxidation temperature of as-fabricated U 3 Si 2 pellets to 580 °C, which can be further increased to 610 °C by thermal annealing. The Al-doped U 3 Si 2 composite fuels also display simultaneously higher hardness and fracture toughness than un-doped U3Si2. These results highlight an effective strategy by integrating minimal Al additives, microstructure control and post-thermal annealing to design advanced silicide fuels with excellent oxidation resistance, desired thermal-mechanical properties and maintained high fissile element density.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Probing Terra Incognita of Ni–P Catalysts: Operando Explorations during Hydrogen Evolution Reaction

We have developed two Ni phosphide preparation methods allowing operando XAS surface-sensitive studies of well-defined bulk systems. For Ni K-edge XAS, a Ni 2 P phase-pure powder was sintered into a high-density pellet and polished for grazing incidence XAS. Ni sites were mildly affected by the acidic electrolyte prior to the HER, while the applied cathodic potential caused the reduction of Ni surface states beyond the states of as-prepared Ni 2 P. The computed fully H-covered Ni 2 P [0001] model describes the difference in the operando Ni K-edge GIXAS spectrum well. Upon turning the applied bias off, the Ni sites became immediately oxidized, forming NiO on the surface. Thus, the active phase during the HER is covalent Ni 0 close to that in the intermetallic phosphides, and Ni 2+ oxides formed after, and not during, the HER. For P K-edge XAS, Ni foam was phosphorized to form a thin Ni 3 P layer while preserving its high surface area. Upon immersion in the acidic electrolyte, the P sites underwent removal of P 5+ phosphates and formed new P coordination, possibly due to the adsorption of protons from the electrolyte. These new P surface states were not affected by turning the cathodic current on and off as soon as the sample was immersed in the acidic electrolyte. However, the removal of the sample from the electrochemical cell and drying in air resulted in substantial depletion and oxidation of surface P. Echoing the observed Ni site chemistry during HER, XAS and XPS suggest that the in situ active P sites are different from the oxidized P states observed under ex situ conditions.

Kong, Seongyoung [Iowa State Univ., Ames, IA (Unit↗
DOE OSTI2020

The ionic conductivity of Sm‐doped ceria

Abstract The oxygen ion conductivity of polycrystalline samples of Sm‐doped ceria and of Gd‐doped ceria is studied as a function of doping fraction and temperature using impedance spectroscopy allowing the separation of bulk and grain boundary conductivity. The introduction of a fine spacing for the Sm dopant fraction allows the clear identification of the dopant fraction leading to the largest bulk conductivity. At 267°C, the largest bulk conductivity is shown for Ce 0.93 Sm 0.07 O 1.965 . With increasing temperature, indications of an increase in the dopant fraction, which leads to the maximum in conductivity, are found. For the grain boundary conductivity, the maximum appears at larger dopant fractions compared to the bulk conductivity. The largest total conductivity for both dopants is again found for Sm‐doped ceria. In literature, different syntheses and sample preparation methods led to larger total conductivities for Gd‐doped ceria. In this work, we demonstrate that the variation of sintering conditions leads to scattering in the conductivity over one order of magnitude. Finally, we demonstrate that, in nominally pure cerium oxide, impurities dominate the ionic conductivity.

Koettgen, Julius↗
DOE OSTI2023

A Study of a Surrogate Nuclear Thermal Propulsion Fuel Element

We report a surrogate fuel, Zirconium Carbide/Titanium Nitride has been prepared using a simple method to obtain a more uniform distribution of titanium nitride in the zirconium carbide matrix. Powders were sintered using Spark Plasma Sintering at 1750oC and 1850oC using a modified sintering profile. This resulted in a fairly uniform distribution of titanium nitride in the zirconium carbide matrix with a density of 95% of theoretical at 1850oC. Scanning electron microscopy, indentation hardness and x-ray diffraction results are given.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Thermophysical properties of high-density, sintered monoliths of yttrium dihydride in the range 373–773 K

Yttrium dihydride is a promising nuclear reactor moderator for high-temperature, thermal micro-reactors due to its ability to retain hydrogen to high temperatures while having a relatively low impact on neutron economy. However, it is difficult to fabricate yttrium dihydride in high-density, near net-shape monoliths for moderator applications due to challenges associated with the hydrogen absorption process. Here, high-density monoliths of yttrium dihydride were prepared by powder metallurgical methods. The lattice strain and thermal expansion coefficient were measured using neutron diffraction of powders of directly-hydrided yttrium, while the molar heat capacity and thermal diffusivity of sintered yttrium dihydride were measured using differential scanning calorimetry (DSC) and laser flash analysis (LFA), respectively. The molar heat capacity of yttrium dihydride was also calculated using density functional theory (DFT) for comparison. These parameters were used to then calculate the thermal conductivity and resistivity of yttrium dihydride as a function of temperature. The thermophysical properties of materials produced by both methods were observed to be consistent with the values from literature for yttrium dihydride. Due to the novelty of producing yttrium dihydride by powder metallurgical methods, this result indicated that the sintered monoliths were of high quality and that powder metallurgy is a viable method for large-scale production of yttrium dihydride monoliths for nuclear reactor moderator applications.

36 MATERIALS SCIENCE↗