Search NASA⌕ Search

SEARCH · Search NASA

Results for “sintering temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An evaluation of tri-valent oxide (Cr 2 O 3 ) as a grain enlarging dopant for UO 2 nuclear fuels fabricated under reducing environment

A study was performed to evaluate the microstructure and crystallography of nominally 500–2000 Cr 2 O 3 -doped UO 2 fabricated in a temperature range of 1150–1750°C under reducing experimental conditions. We observed an increase in grain size of the samples with the increase in heat treating temperature as expected. For a given sintering temperature (1700–1750°C), an increase in the grain size was also observed with the increase in Cr 2 O 3 concentration up to a value of ~1000–1200 wppm. A decrease in fission gas release as a function of grain size was estimated for the Cr 2 O 3 -doped UO 2 samples assuming specified post-irradiation annealing conditions. A nearly linear decrease was obtained in the lattice parameter of the Cr 2 O 3 -doped UO 2 fcc phase with the increase in Cr 2 O 3 concentration, especially up to a nominal value of 1000 wppm. The lattice parameter decrease was also persistent with the increase in the average grain size as a result of addition of Cr 2 O 3 into the UO 2 lattice. An increase in the crystallite size and a decrease in the microstrain of the $fcc$ phase were observed with the increase in the average grain size of the samples, indicating a higher crystallinity of the Cr 2 O 3 -doped samples than that of the undoped UO 2 sample.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Improving protonic ceramic electrochemical cell performance via a dual-phase reaction-sintered bilayer electrolyte

Protonic ceramic electrochemical cells (PCCs) are promising energy conversion devices, but their fabrication remains challenging. In particular, the typical electrolytes for PCCs such as BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3−δ (7111) and BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3−δ (4411) suffer from intrinsic barium evaporation issues during high-temperature sintering. This tendency towards barium loss, combined with their highly refractory nature, leads to a tradeoff between sinterability and chemical stability. To address this tradeoff, we propose a bilayer electrolyte combining layers of 4411 and 7111 materials that is designed to enhance sinterability and conductivity through dual-phase reactive sintering. Our findings demonstrate that the bilayer structure exhibits shrinkage behavior closely matched to that of the fuel electrode substrate, with a higher shrinkage compared to a single-layer 4411 electrolyte. Utilizing this bilayer electrolyte structure, our PCCs achieve a peak power density of 637 mW∙cm −2 in fuel-cell mode and a current density of 1060 mA∙cm −2 at 1.3 V in electrolysis mode at 600 °C. Our PCCs demonstrate high Faradaic efficiency of 83% at 1.3 V and 500 °C. Hybrid distribution of relaxation times (DRT) polarization mapping further reveals that the bilayer structure reduces Ohmic and polarization resistance in both fuel-cell and electrolysis modes.

ceramic processing↗
DOE OSTI2024

Exploring laser-material interactions of zirconium carbide under additive manufacturing conditions

Zirconium carbide (ZrC) is an ultra-high temperature ceramic with a melting temperature above 3000°C and a broad range of high temperature applications. Given the high melting and sintering temperatures of pure ZrC, producing near-net shape and fully dense parts remains challenging with conventional techniques. In this study, we investigate the fundamental laser-material interactions of ZrC under laser powder bed fusion (LPBF) additive manufacturing (AM) conditions. Normalized enthalpy, a scaling law term that is used in welding and AM literature for detailing laser-material interactions in metallic alloys, was calculated to determine the predictive capabilities of melt pool features in ZrC. Further, the melt pool quality of laser irradiated ZrC was used to compare LPBF relevant laser parameter combinations of laser power, scan speed, and beam diameter. Laser build parameters that resulted in desirable melt pool morphologies were applied to the fabrication of ZrC coupons using LPBF AM. A custom LPBF system was used to determine hatch spacing and layer height parameters that resulted in a fabricated sample with a density of 85% as measured by Archimedes and a Vicker's microhardness of 20.9 ± 1.9 GPa. This investigation reveals the laser-material interactions of ZrC under AM relevant conditions and is the first step towards LPBF fabrication of ZrC parts.

36 MATERIALS SCIENCE↗
DOE OSTI2026

The influence of iron incorporation on the microstructure and crystal chemistry of UO 2 fuel

The incorporation of dopants into UO 2 is of interest for both doped advanced fuel and nuclear forensics research. Suitable forensics dopants, or taggants, for nuclear fuels are ones that do not adversely affect the performance of the parent material while still being traceable during key stages of the fuel’s life cycle. In this paper, we present our efforts to understand the effects of doping UO 2 with Fe 2 O 3 under multiple parameters, such as Fe concentration (0–3000 wppm), sintering temperature (1673 K, 1773 K, and 1973 K), sintering time (2–12 h), and atmosphere (reducing and inert). Here, we investigated densification behavior, microstructure evolution, and lattice defects based on the geometric densities, scanning electron microscopy (SEM), X-ray diffractograms, and Raman spectra. The effect of Fe on the microstructure and crystal chemistry of UO 2 is very complex, especially at the intermediate temperature (1773 K), where we found that densification kinetics are enhanced and that lattice contraction occurs for doping concentrations greater than 1000 wppm Fe.

Crystallography↗
DOE OSTI2025

Sintering protonic zirconate cells with enhanced electrolysis stability and Faradaic efficiency

The emerging applications of steam electrolysis and electrochemical synthesis at 300–600 °C set stringent requirements on the stability of protonic ceramic cells, which cannot be met by Ce-rich electrolytes. A promising candidate is Ce-free BaZr 0.8 Y 0.2 O 3–δ , but its usage has long been hindered due to the high sintering temperatures required for protonic devices. Here we resolved the issue through a co-sintering process, in which the shrinkage stress of a readily sinterable support layer helps to densify the pure BaZr 0.8 Y 0.2 O 3–δ electrolyte membrane at low temperatures. This approach eliminates Ce and harmful sintering aids in the dense zirconate electrolyte membrane, thereby enhancing the Faradaic efficiency and electrochemical stability, especially under harsh operating conditions. Here, the protonic zirconate cells have exceptional performance and demonstrate stable high-steam pressure electrolysis up to 0.7 atm steam pressure, –2 A cm –2 current density and over 800 h of dynamic operation at 600 °C. Our processing breakthrough enables stabilized protonic cells for demanding applications in future energy infrastructure.

25 ENERGY STORAGE↗
DOE OSTI2021

A Double-side Cooled SiC MOSFET Power Module with Sintered-silver Interposers: I. Design, Simulation, Fabrication, and Performance Characterization

Planar, double-side cooled power modules are emerging in electric-drive inverters because of their low profile, better heat extraction, and lower package parasitic inductances. However, there is still concern about their reliability due to the rigid interconnection between the device chips and two substrates of the power module. In this paper, a porous interposer made of low-temperature sintered silver is introduced to reduce the thermo-mechanical stresses in the module. A double-side cooled half-bridge module consisting of two 1200 V, 149 A SiC MOSFETs was designed, fabricated, and characterized. By using the sintered-Ag instead of solid copper interposers, our simulation results showed that at a total power loss of 200 W, the thermo-mechanical stress at the most vulnerable interfaces (interposer-attach layer) was reduced by 42 % and in the SiC MOSFET by 50 % with a trade-off of only 3.6 % increase in junction temperature. The sintered-Ag interposers were readily fabricated into desired dimensions without post-machining and did not require any surface finishing for die-bonding and substrate interconnection by silver sintering. Here, the porous interposers were also deformable under a low force or pressure, which helped to accommodate chip thickness and/or substrate-to-substrate gap variations in the planar module structure, thus simplifying module fabrication. Experimental results on the electrical performance of the fabricated SiC modules validated the success of using the porous silver interposers for fabricating planar, double-side cooled power modules.

42 ENGINEERING↗
DOE OSTI2025

Direct ink writing of aqueous-based Gadolinium (III) oxide slurries

Gadolinium (III) oxide (gadolinia, Gd 2 O 3 ) has recently been identified as an intriguing material for applications in the medical, solid oxide fuel cell, and nuclear industries. This interest drives the need for developing and understanding manufacturing techniques that can produce dense Gd 2 O 3 structures. Direct ink writing (DIW), an extrusion-based additive manufacturing method, has also garnered interest because of its capability to produce dense ceramic parts with increased complexity in an economical manner. In this study, DIW was explored as a manufacturing technique for Gd 2 O 3 . Experiments were performed to develop Gd 2 O 3 bearing inks capable of being processed via DIW. Ink solids loading and sintering temperatures were varied to assess their impact on the final density and microstructure. Optimum sintering conditions are proposed and were experimentally verified at a dwell temperature of 1500°C. Gd 2 O 3 samples were successfully manufactured using DIW, achieving densities greater than 96 % of the theoretical density.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An investigation of the long-range and local structure of sub-stoichiometric zirconium carbide sintered at different temperatures

ZrC 1-x (sub-stoichiometric zirconium carbide), a group IV transition metal carbide, is being considered for various high temperature applications. Departure from stoichiometry changes the thermo-physical response of the material. Reported thermo-physical properties exhibit, in some cases, a degree of scatter with one likely contributor to this being the uncertainty in the C/Zr ratio of the samples produced. Conventional, methods for assigning C/Zr to samples are determined either by nominal stochiometric ratios or combustion carbon analysis. In this study, a range of stoichiometries of hot-pressed ZrC 1-x were examined by SEM, XRD, Raman spectroscopy and static 13 C NMR spectroscopy and used as a basis to correct the C/Zr. Graphite, amorphous, and ZrC 1-x carbon signatures are observed in the 13 C NMR spectra of samples and are determined to vary in intensity with sintering temperature and stoichiometry. In this study a method is outlined to quantify the stoichiometry of ZrC 1-x and free carbon phases, providing an improvement over the sole use and reliance of widely adopted bulk carbon combustion analysis. We report significantly lower C/Zr values determined by 13 C NMR analysis compared with carbon analyser and nominal methods. Furthermore, the location of carbon disassociated from the ZrC 1-x structure is analysed using SEM and Raman spectroscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manufacturing porous U10Zr fuels with controlled porosities by SPS and thermal properties

To accommodate the swelling of metallic fuels induced by the fission gas release during burnup in sodium fast reactor for a sodium-free fuel option, advanced U-10Zr fuels with controlled porosity were designed and demonstrated by spark plasma sintering. U-10Zr fuel pellets with manufactured porosities varying from 35% up to fully dense fuel pellets have been fabricated by controlling ball milling times of the starting uranium powders, sintering temperature, pressure, and duration, and the correlation among the microstructure control – porosity – sintering conditions has been established. To further mimick the pore structure in irradiated fuels, different pore formers (NaCl and NH4HCO3) have been used to control the pore size and distribution. Microstructure characterization indicates a lamellar reaction zone of U and Zr, differing from the arc-melted U-10Zr as a result of rapid consolidation of SPS at lower temperature and short durations. The thermal conductivity of U10Zr with different porosities are also measured. Here this work demonstrates the success in manufacturing new metallic fuel forms with controlled porosities and pore distribution, which can be used as model systems to investigate the thermal transfer behavior of metallic fuels in the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

On the Arrhenius-like behavior of conductivity during flash sintering of 3 mol% yttria stabilized zirconia ceramics

Here, we discuss the Arrhenius behavior of electrical conductivity σ during flash sintering of 3 mol% yttria stabilized zirconia (3YSZ). In situ x-ray diffraction is used to determine sample temperature. Sintering contribution to σ is excluded by investigating the flash event on a dense ceramic. We show that total conductivity follows an Arrhenius-like equation in both dense and green samples, even during Stage II of flash. The non-linearity often verified during flash sintering of 3YSZ is therefore related to the furnace temperature instead of the sample temperature when building the ln(σ) vs. 1/T plots. Furthermore, we verified a change in the activation energy for conduction prior to the ignition of the flash event and discussed the possible mechanisms. For instance, the decrease in activation energy from Stage I to II in the dense sample is attributed to a contribution from electronic carriers.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Doping effect of Al in LLZO

Lithium ion batteries have become a common use in most electronic devices and transportation. However, the use of liquid electrolytes poses a serious safe hazard due to their high flammability. The narrow operating temperature and voltage windows also limit further improvement of the energy density.Solid-state lithium batteries with the use of more stable and safer solid electrolyte have garnered much attention and could be the future choice for battery technology. A promising potential candidate for the solid electrolyte component is the garnet type Li 7 La 3 Zr 2 O 12 (LLZO) ceramic material since it possesses high ionic conductivity at room temperature and enables the use of high capacity lithium anode and high voltage/capacity cathodes.However, to form the stable cubic phase of LLZO and high densification,high sintering temperatures above 1100°C is typically required, which causes Lithium loss of the system.Many studieshave been taken to dop LLZO with various precursors such as Ga, Ta, and Al to stabilize the cubic structure and reduce calcination temperature, while the doping effect on sintering densification is still unclear. In this study Al doping along with ball milling were explored to stabilize the cubic phase of LLZO and improve densification, while reducing the amount of impurity phases. Samples were synthesized from the precursors Li 2 CO 3 , Al 2 O 3 , La 2 O 3 , and ZrO 2 by ball milling followed by heat treatment for 12 hours at 1000°C. XRD with Rietveld fitting was used to determine the two phases of LLZO (cubic, tetragonal) and other possible secondary phases. Furthermore,SEM with top and cross sectional views was conducted to investigate the morphology and microstructure of sintered pellets.

36 MATERIALS SCIENCE↗
DOE OSTI2023

CuCr 2 O 4 particle growth and evolution across sol–gel routes and calcination profiles

CuCr 2 O 4 spinel is a candidate coating material for central receivers in concentrating solar power to protect structural alloys against high temperature oxidation and related degradation. Coating performance and microstructure of dip-coated and sintered coatings is dictated by the initial particle size of the CuCr 2 O 4 and sintering temperature, but can be compromised by particle agglomeration. Here in this study, sub-micron particles were synthesised through the Pechini and modified Pechini sol–gel methods. Phase composition was confirmed via X-ray diffraction. Particle growth during calcination of the nanoparticles at different temperatures (650°C, 750°C, 850°C) and times (between 1 and 24 h) was measured via laser diffraction and scanning electron microscopy. The modified Pechini method displayed evidence of smaller particle sizes and greater agglomeration. The kinetics of particle growth observed are consistent with a diffusion limited inhibited grain growth model.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of a high-temperature Inconel 625 heat exchanger by model design and binder jetting additive manufacturing

A nickel-based Inconel 625 superalloy heat exchanger for high-temperature applications was developed via binder jetting additive manufacturing. The material properties were characterized first on printed and sintered parts. Two sintering temperatures were used to investigate the effects of the temperature on densification and microstructure. For channel geometry design, the heat transfer capabilities of the heat exchanger were optimized for the cross-section geometry of fluid flow channels in a counterflow configuration, and a stress analysis was conducted to investigate the effects of channel geometry. After headers were incorporated into the heat exchanger as a one-piece component, a prototype was printed. A complete depowdering was achieved via compressed air blowing, and sintering was performed with the developed profile. Ultimately, a one-piece heat exchanger with a nearly full density was obtained. Heat transfer tests were performed on this unit, and the results were compared with those from the simulations. In this study, systematic processes were developed for an additively manufactured Inconel-based heat exchanger for high-pressure, high-temperature heat transfer applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rapid Laser Reactive Sintering of Garnet Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 and Li 6.1 La 3 Zr 2 Al 0.3 O 12 and Solid-State Electrolytes

All solid-state lithium-ion batteries (ASSLIBs) have gained significant interest in recent years due to their wide range of applications, including mobile devices, electric vehicles, and grid storage. Garnet-type Li 7 La 3 Zr 2 O 12 (LLZO) solid-state electrolyte (SSE) continues to be a significant player in the fabrication of ASSLIBs with excellent ionic conductivity on the order of 10 -3 S•cm -1 with the integration of dopants and sintering aids to assist conductivity and structural evolution during the sintering procedure. Traditional sintering techniques, such as solid-state sintering (SSS), have been proven to yield desirable crystal structures. However, the low ionic conductivity results from inferior microstructure, and lithium loss is a significant challenge. Recently, a relatively novel sintering process called rapid laser sintering (RLS) has shown great potential for achieving fully dense solid oxide electrolytes with less lithium loss, resulting in high ionic conductivity [1] [2] [3] [4]. Here, we applied a modified RLS method using precursor powders instead of pre-synthesized LLZO powders to fabricate Al-doped LLZO (Li 6.1 La 3 Zr 2 Al 0.3 O 12 + 13 wt% Li 2 CO 3 ) and Ta-doped LLZO (Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 + 5 wt% LiOH•H 2 O) dense electrolytes. This rapid laser reactive sintering (RLRS) could potentially reduce the number of processing steps and therefore lower the manufacturing cost. We hope the rapid high-temperature sintering can densify the electrolyte and avoid the lithium loss for achieving high lithium-ion conductivity. In this work, we optimized a combination of laser parameters (speed and power), initial precursor composition, and controlled atmospheres to discover the optimal conditions for reaching the efficacious crystal structure, microstructure, and ionic conductivity.

25 ENERGY STORAGE↗
DOE OSTI2020

Highly Ordered Carbon Coating Prepared with Polyvinylidene Chloride Precursor for High‐Performance Silicon Anodes in Lithium‐Ion Batteries

Abstract A highly ordered carbon structure based on polyvinylidene chloride precursor has been developed to host silicon nanoparticles. The stoichiometric ratio of sacrificial H and Cl elements facilitated full utilization of the carbon content of the precursor that produced robust carbon coatings on silicon nanoparticles with excellent mechanic properties and electrochemical stabilities. The optimal sintering temperature and carbon content have been investigated. When evaluated as the anode of a lithium‐ion battery (LIB), the Si : C 1 : 2 composite sintered at 800 °C (SiC12‐800) provided excellent capacity retention of 85 % at 0.1 C after 50 cycles with an enhanced CE, which reached 99 % only after 10 cycles. The SiC12‐800 electrode maintained a specific capacity of 709.2 mAh/g after 300 cycles at 0.3 C, and delivered a high rate performance of 737.9 mAh/g and 485.6 mAh/g at 5 C and 10 C, respectively. The results indicate that polymer precursors with stoichiometric ratio of sacrificial elements have high potential for generating highly robust carbon coatings for silicon anodes in high energy density LIBs.

Zhou, Shuo↗
DOE OSTI2021

Exploring the structural uniformity and integrity of protonic ceramic thin film electrolyte using wet powder spraying

Thin protonic ceramic electrolyte contributes to lower ohmic resistance and enhances electrochemical performance of protonic ceramic electrochemical cells. However, manufacturing of large-scale thin electrolyte remains a challenge. Wet powder spraying is an attractive technique to deposit <10 µm thin electrolyte when advanced atomizing techniques and optimized spraying process are integrated. Here ultrasonic atomization is integrated in the wet powder spray technique to reduce the thickness of electrolyte. Moreover, a parametric study is conducted to optimize the wet powder spray process to deposit uniform and crack-free electrolyte film. It is illustrated that tuning of solid loading rates and spray passes can affect the morphology of the as-sprayed electrolyte film, enabling the structural compactness of the sintered electrolyte layer. To maintain chemical stability of the electrolyte layer during sintering, effect of sintering temperature is further investigated to produce a physically thin, structurally dense, and chemically homogeneous electrolyte layer. The protonic ceramic electrochemical cells fabricated with optimized spraying and sintering parameters demonstrate excellent performance under both fuel cell and electrolysis modes. In addition, the cells exhibit remarkable structural integrity during redox and long-term stability tests.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Zirconium-diboride silicon-carbide composites: A review

Zirconium diboride (ZrB 2 ) and silicon carbide (SiC) composites have long been of interest since it was observed that ZrB 2 improved the thermal shock resistance of SiC. However, processing of these materials can be difficult due to high and different sintering temperatures and differences in the thermodynamic stability of each material. ZrB 2 –SiC composites have been processed in a variety of ways including hot-pressing, spark-plasma sintering, reactive melt infiltration, pack cementation, chemical vapor deposition, chemical vapor infiltration, stereolithography, direct ink writing, selective laser sintering, electron beam melting, and binder jet additive manufacturing. Each manufacturing method has its own pros and cons. This review serves to summarize more than 60 years of research and provide a coherent resource for the variety of methods and advancements in development of ZrB 2 –SiC composites.

36 MATERIALS SCIENCE↗