Search NASA⌕ Search

SEARCH · Search NASA

Results for “static engine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1962

DEVELOPMENT OF A LIGHT-WEIGHT REGENERATIVELY COOLED THRUST CHAMBER WITH BRAZED RIBS AND BRAZED OUTER WIRE TRAP

Design and fabrication procedures are discussed of a brazed-ribtype thrust chamber fabricated from stainless steel or inconel for a Sooo-lb thrust 20: 1 expansion-area-ratio regeneratively cooled liquidpropellant rocket engine which is designated as the JPL 6K Engine and operates at a chamber pressure of 150 psia. Hydrazine is used as the fuel and regenerative coolant and nitrogen tetroxide as the oxidizer. The nozzle-throat diameter is 5.42 in. The thrust chamber consists of a sheet-metal gas-side liner with longitudinal ribs spotwelded and brazed to the outer surface. Wire is wrapped over the ribs circumferentially, spot-welded to the ribs, and brazed. The liner, ribs, and wire form the coolant-passage walls. There are three basic advantages to this type of thrust chamber: light weight, ease of fabrication, and comparatively low cost. The total dry weight of a thrust chamber of this type and size made of 347 stainless steel is 46.2 lb, and the wet weight is 56.3 Ib. A total of 87 static engine tests were made on 19 of 23 thrust chambers fabricated by this technique. Four of the chambers tested had an expansion-area ratio of 20:1, and 15, which were shorter but had the same throat diameter, had an expansion-area ratio of 3.5:l. Accumulated test time was 1926 sec, including 558 sec regenerative cooling with hydrazine and 1368 sec cooling with water. One 20:l thrust chamber was subjected to 16 separate engine tests, with an accumulated test time of 399 sec, and was still in very good operating condition after the tests were completed. With water flowing through the coolant passages at 10 lb/sec, the measured nominal pressure drop between coolant manifolds of a 20:l thrust chamber wrapped with flat wire was 17.2 psi.

Thrust Chamber↗
NASA NTRS2009

Assessment of Soft Vane and Metal Foam Engine Noise Reduction Concepts

Two innovative fan-noise reduction concepts developed by NASA are presented - soft vanes and over-the-rotor metal foam liners. Design methodologies are described for each concept. Soft vanes are outlet guide vanes with internal, resonant chambers that communicate with the exterior aeroacoustic environment via a porous surface. They provide acoustic absorption via viscous losses generated by interaction of unsteady flows with the internal solid structure. Over-the-rotor metal foam liners installed at or near the fan rotor axial plane provide rotor noise absorption. Both concepts also provide pressure-release surfaces that potentially inhibit noise generation. Several configurations for both concepts are evaluated with a normal incidence tube, and the results are used to guide designs for implementation in two NASA fan rigs. For soft vanes, approximately 1 to 2 dB of broadband inlet and aft-radiated fan noise reduction is achieved. For over-the-rotor metal foam liners, up to 3 dB of fan noise reduction is measured in the low-speed fan rig, but minimal reduction is measured in the high-speed fan rig. These metal foam liner results are compared with a static engine test, in which inlet sound power level reductions up to 5 dB were measured. Brief plans for further development are also provided.

Jones, Michael G.↗
NASA NTRS1960

Turbulence Studies of a Rectangular Slotted Noise-Suppressor Nozzle

The problem of noise suppression of turbojet engines has shown a need for turbulence data within the flow field of various types of nozzles used in ad hoc investigations of the sound power. The result of turbulence studies in a nozzle configuration of four parallel rectangular slots is presented in this report with special attention to the effect of the spacing of the nozzles on the intensity of turbulence, scale of turbulence, spectrum of turbulence, and the mean stream velocity. Taylor's hypothesis, which describes the convection of the turbulence eddies, was tested and found correct within experimental error and certain experimental and theoretical limitations. The convection of the pressure patterns was also investigated, and the value of the convection velocity was found to be about 0.43 times the central core velocity of the jets. The effect of the spacing-to-width ratio of the nozzles upon the turbulence intensity, the scale of turbulence, and the spectral distribution of the noise was found in general to produce a maximum change for spacing-to-width ratios of 1.5 to 2.0. These changes may be the cause of the reduction in sound power reported for similar full-scale nozzles and test conditions under actual (static) engine operation. A noise reduction parameter is defined from Lighthill's theory which gives qualitative agreement with experiments which show the noise reduction is greatest for spacing-to-width ratios of 1.5 to 2.0.

Laurence, James C.↗
NASA NTRS1991

Aging aircraft NDI Development and Demonstration Center (AANC): An overview

A major center with emphasis on validation of nondestructive inspection (NDI) techniques for aging aircraft, the Aging Aircraft NDI Development and Demonstration Center (AANC), has been funded by the FAA at Sandia National Laboratories. The Center has been assigned specific tasks in developing techniques for the nondestructive inspection of static engine parts, assessing inspection reliability (POD experiments), developing testbeds for NDI validation, maintaining a FAA library of characterized aircraft structural test specimens, and leasing a hangar to house a high flight cycle transport aircraft for use as a full scale test bed.

Aging Aircraft↗
NASA NTRS1995

UHB Engine Fan Broadband Noise Reduction Study

A study has been completed to quantify the contribution of fan broadband noise to advanced high bypass turbofan engine system noise levels. The result suggests that reducing fan broadband noise can produce 3 to 4 EPNdB in engine system noise reduction, once the fan tones are eliminated. Further, in conjunction with the elimination of fan tones and an increase in bypass ratio, a potential reduction of 7 to 10 EPNdB in system noise can be achieved. In addition, an initial assessment of engine broadband noise source mechanisms has been made, concluding that the dominant source of fan broadband noise is the interaction of incident inlet boundary layer turbulence with the fan rotor. This source has two contributors, i.e., unsteady life dipole response and steady loading quadrupole response. The quadrupole contribution was found to be the most important component, suggesting that broadband noise reduction can be achieved by the reduction of steady loading field-turbulence field quadrupole interaction. Finally, for a controlled experimental quantification and verification, the study recommends that further broadband noise tests be done on a simulated engine rig, such as the GE Aircraft Engine Universal Propulsion Simulator, rather than testing on an engine statically in an outdoor arena The rig should be capable of generating forward and aft propagating fan noise, and it needs to be tested in a large freejet or a wind tunnel.

Gliebe, Philip R.↗
NASA NTRS1996

Thrust Vectoring on the NASA F-18 High Alpha Research Vehicle

Investigations into a multiaxis thrust-vectoring system have been conducted on an F-18 configuration. These investigations include ground-based scale-model tests, ground-based full-scale testing, and flight testing. This thrust-vectoring system has been tested on the NASA F-18 High Alpha Research Vehicle (HARV). The system provides thrust vectoring in pitch and yaw axes. Ground-based subscale test data have been gathered as background to the flight phase of the program. Tests investigated aerodynamic interaction and vane control effectiveness. The ground-based full-scale data were gathered from static engine runs with image analysis to determine relative thrust-vectoring effectiveness. Flight tests have been conducted at the NASA Dryden Flight Research Center. Parameter identification input techniques have been developed. Individual vanes were not directly controlled because of a mixer-predictor function built into the flight control laws. Combined effects of the vanes have been measured in flight and compared to combined effects of the vanes as predicted by the cold-jet test data. Very good agreement has been found in the linearized effectiveness derivatives.

Bowers, Albion H.↗
NASA NTRS2001

Materials Overview

The Materials and Structures for High Performance project has made excellent progress in the development of advanced high-temperature materials and computational materials science tools to enable high-performance, hgh-efficiency, and environmentally compatible propulsion systems. Ceramic matrix composite (CMC) systems with 2700 O F temperature capability are initially being developed for low NO, combustor liners and turbine vanes. The feasibility of pushing CMC technologies to 3000 O F through revolutionary concepts is also being pursued. Achieving fuel savings of 8 to 15 percent requires higher turbine inlet temperatures as well as reductions in engine weight. An advanced disk alloy has been evaluated for application in future engines. Advanced thermal barrier coatings (TBC s) will enable 3200 O F turbine rotor inlet temperature capability. Advanced alloy development and the development of computational tools for the design of these future alloys will further enable attainment of these goals. Innovative lightweight materials, and structural and nozzle aerodynamic concepts are also being developed to reduce the weight of engine static structures to contribute toward overall fuel savings. Rig tests will demonstrate long-term durability of CMC linersand vanes and advanced turbine airfoil alloy systems, as well as fabricability of components with the highest payoff potential using the lightweight materials and structures concepts being developed.

Draper, Robert↗
NASA NTRS2015

Phase-Based Adaptive Estimation of Magnitude-Squared Coherence Between Turbofan Internal Sensors and Far-Field Microphone Signals

A cross-power spectrum phase based adaptive technique is discussed which iteratively determines the time delay between two digitized signals that are coherent. The adaptive delay algorithm belongs to a class of algorithms that identifies a minimum of a pattern matching function. The algorithm uses a gradient technique to find the value of the adaptive delay that minimizes a cost function based in part on the slope of a linear function that fits the measured cross power spectrum phase and in part on the standard error of the curve fit. This procedure is applied to data from a Honeywell TECH977 static-engine test. Data was obtained using a combustor probe, two turbine exit probes, and far-field microphones. Signals from this instrumentation are used estimate the post-combustion residence time in the combustor. Comparison with previous studies of the post-combustion residence time validates this approach. In addition, the procedure removes the bias due to misalignment of signals in the calculation of coherence which is a first step in applying array processing methods to the magnitude squared coherence data. The procedure also provides an estimate of the cross-spectrum phase-offset.

Combustion↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design With and Without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design with and without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗
NASA NTRS1980

Prediction of unsuppressed jet engine exhaust noise in flight from static data

A methodology developed for predicting in-flight exhaust noise from static data is presented and compared with experimental data for several unsuppressed turbojet engines. For each engine, static data over a range of jet velocities are compared with the predicted jet mixing noise and shock-cell noise. The static engine noise over and above the jet and shock noises is identified as excess noise. The excess noise data are then empirically correlated to smooth the spectral and directivity relations and account for variations in test conditions. This excess noise is then projected to flight based on the assumption that the only effects of flight are a Doppler frequency shift and a level change given by 40 log (1 - m sub 0 cos theta), where M sub 0 is the flight Mach number and theta is the observer angle relative to the jet axis.

Stone, J. R.↗
NASA NTRS1980

Prediction of unsuppressed jet engine exhaust noise in flight from static data

In order to assess the impact of aircraft noise on the environment in the vicinity of an airport, it is essential that a methodology be developed for predicting in-flight exhaust noise from static data. Such a methodology is presented in this paper and is compared with experimental data for several unsuppressed turbojet engines. For each engine, static data over a range of jet velocities are compared with the predicted jet mixing noise and shock-cell noise. The static engine noise over and above the jet and shock noises is identified as 'excess' noise. The excess noise data are then empirically correlated to smooth the spectral and directivity relations and account for variations in test conditions. This excess noise is then projected to flight based on the assumption that the only effects of flight are a Doppler frequency shift and a level change. The effects of flight on jet mixing noise and shock noise are computed by published NASA methods.

Stone, J. R.↗
NASA NTRS1983

Effects of wind on turbofan engines in outdoor static test stands

Wind can affect measured thrust and can cause turbofan engine speed to fluctuate during outdoor testing. Techniques used at an outdoor test stand at NASA Lewis Research Center to make testing easier and faster and to improve data repeatability include using an inflow control device (ICD) to make fan speed steadier, taking many raw data samples for better averaging, and correcting thrust for wind direction and speed. Data from engine tests are presented to show that the techniques improve repeatability of thrust and airflow measurements under various wind conditions.

Mcardle, J. G.↗
NASA NTRS1983

Effects of wind on turbofan engines in outdoor static test stands

Wind can affect measured thrust and can cause turbofan engine speed to fluctuate during outdoor testing. Techniques used at an outdoor test stand at NASA Lewis Research Center to make testing easier and faster and to improve data repeatability include using an inflow control device (ICD) to make fan speed steadier, taking many raw data samples for better averaging, and correcting thrust for wind direction and speed. Data from engine tests are presented to show that the techniques improve repeatability of thrust and airflow measurements under various wind conditions. Previously announced in STAR as N83-34945

Mcardle, J. G.↗
NASA NTRS1947

Performance of Compressor of XJ-41-V Turbojet Engine: Compressor Static-Pressure Rise at Equivalent Compressor Speeds of 5000, 7000, 8000, and 9000 rpm - 3

At the request of the Air Materiel Command, Army Air Forces, an investigation is being conducted at the NACA Cleveland laboratory to determine the performance characteristics of the XJ-41-V turbojet-engine compressor. The static-pressure variation in the direction of flow through the compressor was presented in reference 1 for an equivalent speed of 8000 rpm. An analysis of these pressure indicated that the maximum-flow limitation of the compressor was caused by separation, which reduced the effective flow area at the vaned-collector entrance. As a result of this analysis, the flow area at the vaned-collector entrance was increased to obtain larger mass flows. The area increase was obtained by cutting back the entrance edges of the collector vanes, which resulted in an increased vaneless-diffuser radius. Comparative performance of the original and revised compressors at an equivalent speed of 8000 rpm is presented. The static-pressure rise through the compressor, determined from static pressures at the impeller entrance and the vaned-collector exit, is also presented together with the compressor adiabatic efficiency and the mass flow over an equivalent speed range from 5000 to 9000 rpm. These static-pressure data are presented for the purpose of correlating the compressor performance with the turbojet-engine performance.

Creagh, John W. R.↗
NASA NTRS1948

Performance of Compressor of XJ-41-V Turbojet Engine II - Static-Pressure Ratios and Limitation of Maximum Flow at Equivalent Compressor Speed of 8000 rpm

At the request of the Air Material Command, Army Air Forces, an investigation was conducted by the NACA Cleveland laboratory to determine the performance characteristics of the compressor of the XJ-41-V turbojet engine. This report is the second in a series presenting the compressor performance and analysis of flow conditions in the compressor. The static-pressure variation in the direction of flow through the compressor and the location and the cause of the maximum flow restriction at an equivalent speed of 8000 rpm are presented. After the initial runs were reported, the leading edges of the impeller blades and the diffuser surfaces were found to have been roughened by steel particles from a minor failure of auxiliary equipment. The leading edges of the impeller blades were refinished and all high spots resulting from scratches in the diffuser and the accessible parts of the vaned collector passages were removed. The initial overall performance and that obtained with the refinished blades are presented.

Dildine, Dean M.↗