Search NASA⌕ Search

SEARCH · Search NASA

Results for “storing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Computation of a controlled store separation from a cavity

Coupling of the Reynolds-averaged Navier-Stokes equations, rigid-body dynamics, and a pitch attitude control law is demonstrated in two- and three-dimensions. The application problem was the separation of a canard-controlled store from an open-flow rectangular cavity bay at a freestream Mach number of 1.2. The transient flowfield was computed using a diagonal scheme in an overset mesh framework, with the resultant aerodynamic loads used as the forcing functions in the nonlinear dynamics equations. The proportional and rate gyro sensitivities were computed a priori using pole placement techniques for the linearized dynamical equations. These fixed gain values were used in the controller for the nonlinear simulation. Reasonable comparison between the full and linearized equations for a perturbed two-dimensional missile was found. Also in two-dimensions, a controlled store was found to possess improved separation characteristics over a canard-fixed store. In three-dimensions, trajectory comparisons with wind-tunnel data for the canard-fixed case will be made. In addition, it will be determined if a canard-controlled store is an effective means of improving cavity store separation characteristics.

Atwood, Christopher A.↗
NASA NTRS1947

Wind-Tunnel Tests of a 0.182-Scale Model of an F4U-1 Airplane with External Stores

Tests were made in the Langley 7- by 10-foot tunnel on a 0.182-scale model of an F4U-1 airplane with external stores. This paper is concerned mainly with presenting the data obtained in this investigation and with a comparison of some of these data with flight-test results determining the feasibility of estimating flight buffet Mach number from tunnel data. The results of this investigation indicate that the incremental drag coefficient due to external stores may be used to estimate the maximum Mach number that the F4U-1 airplane may reach in flight when it is equipped with external stores. This estimation is conservative for the five configurations investigated by mounts varying from 0 to 10 percent of the flight limit Mach number. The free-stream tunnel Mach number corresponding to sonic flow over the lower surface of the wing in the region of the store is a good indication of the lower limit of buffet in flight of the F4U-1 airplane when equipped with external stores. The fluctuations of total pressure over the horizontal tail are not sufficiently large (maximum of 1 percent q(sub o) to cause buffeting of the airplane.

Silvers, H. Norman↗
DOE OSTI2025

Microstructure, stored energy, and stability of H/He-filled nanocavities in low temperature irradiated Inconel 718

The microstructure, trapped transmutation gases, stored energy, and mechanical behavior of samples from an irradiated Inconel 718 proton beam window were characterized using transmission electron microcopy, thermal desorption spectrometry (TDS), differential scanning calorimetry (DSC), and tensile testing. In the as-irradiated condition the microstructure contained a high number density of 1–3 nm gas-filled nanocavities. Emissions of trapped gases, H and He, during TDS correlated with peaks of the energy release curves from DSC examinations, which suggest these gases were likely stored in highly stable defect traps. The stored energy from radiation damage saturated at doses of a few dpa and did not increase with increasing radiation dose, but the amount of stored H and He increased with increasing dose. Effects of post-irradiation annealing were studied as well. After exposure to 700 °C, the nanocavities grew only slightly to 2–4 nm in diameter, but after exposure to 900 °C, the cavities grew to 10–20 nm in diameter and electron energy-loss spectroscopy showed these cavities contained a core of He surrounded by a shell of H. Further, this study demonstrated that the irradiation defect structures containing H and He were remarkably stable during irradiation and after exposure up to 700 °C. The effect of the irradiation temperature, defect mobility, and interaction of H, He, and irradiation defects on mechanical behavior provides insight into the processes responsible for the unusual recovery in ductility with increasing radiation dose observed in Inconel 718 after high energy proton and spallation neutron irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A building performance-based approach to determining energy resilience for grocery stores in the event of a power outage

Evaluating progress toward a built environment that is best equipped to serve communities during a regional power outage will require metrics that capture the energy resilience of the unique buildings and businesses most crucial to the well-being of those nearby. We focused on grocery stores as key buildings for which access, and thus energy resilience, is critical during a disaster when power is unavailable. We evaluated the energy resilience of these buildings by offering and testing building-scale metrics that assess business continuity potential during a power outage. Metrics proposed in this study are calculated based on the unique power loads characteristic to grocery stores, primarily refrigeration and maintaining safe indoor environmental conditions. Building simulations based on varying levels of backup power were carried out against occupant safety and comfort parameters to apply these metrics, with additional criteria imposed on grocery stores to capture the inventory and sales loss from food spoilage resulting from a lack of refrigeration power. Findings from this study demonstrate the feasibility of our proposed metrics and methodology to serve as a low-data burden means for stakeholders to evaluate the energy resilience of grocery stores, with greater implications in helping to understand the impact on community-scale energy resilience.

Siegel, Lino Sanchez↗
DOE OSTI2024

Phase-field modeling of stored-energy-driven grain growth with intra-granular variation in dislocation density

Abstract We present a phase-field (PF) model to simulate the microstructure evolution occurring in polycrystalline materials with a variation in the intra-granular dislocation density. The model accounts for two mechanisms that lead to the grain boundary migration: the driving force due to capillarity and that due to the stored energy arising from a spatially varying dislocation density. In addition to the order parameters that distinguish regions occupied by different grains, we introduce dislocation density fields that describe spatial variation of the dislocation density. We assume that the dislocation density decays as a function of the distance the grain boundary has migrated. To demonstrate and parameterize the model, we simulate microstructure evolution in two dimensions, for which the initial microstructure is based on real-time experimental data. Additionally, we applied the model to study the effect of a cyclic heat treatment (CHT) on the microstructure evolution. Specifically, we simulated stored-energy-driven grain growth during three thermal cycles, as well as grain growth without stored energy that serves as a baseline for comparison. We showed that the microstructure evolution proceeded much faster when the stored energy was considered. A non-self-similar evolution was observed in this case, while a nearly self-similar evolution was found when the microstructure evolution is driven solely by capillarity. These results suggest a possible mechanism for the initiation of abnormal grain growth during CHT. Finally, we demonstrate an integrated experimental-computational workflow that utilizes the experimental measurements to inform the PF model and its parameterization, which provides a foundation for the development of future simulation tools capable of quantitative prediction of microstructure evolution during non-isothermal heat treatment.

Materials Science↗
DOE OSTI2025

BULKI-Store v0.3.2

BULKI-Store is a distributed object storage system optimized for high-performance computing environments. Built with a Rust core and Python bindings, it efficiently manages scientific and machine learning datasets across HPC clusters. The system employs a client-server architecture with MPI integration, enabling seamless scaling on supercomputers like Perlmutter. BULKI-Store's object-oriented approach provides intuitive data organization with rich metadata support, contrasting with traditional file-based solutions. Key optimizations include selective checkpoint loading, unified checkpoint files, and object chunking for large data transfers. For machine learning workloads, BULKI-Store offers advantages through fine-grained access patterns, dynamic data sharing between training instances, and reduced memory pressure. Memory management features include strategic Python GC calls, minimized data copies, and batch processing capabilities. The system leverages Rayon's thread pool for asynchronous data prefetching and supports multiple CPU architectures (ARM64, x86, AMD, RISC-V). By combining performance optimizations with developer-friendly APIs, BULKI-Store addresses the complex data management challenges of modern HPC applications while maintaining compatibility across heterogeneous computing environments.

Zhang, Wei [Lawrence Berkeley National Laboratory ↗
NASA NTRS1972

Some effects of external stores on the static stability of fighter airplanes

Fighter airplanes may have a seemingly limitless number of external store arrangements. Some practical considerations and some aerodynamic considerations must be taken into account in the arrangements of the external stores. The nature of the problems concerning the type of store arrangement involved and the type of airplane on which the stores are installed are reported.

Spearman, M. L.↗
NASA NTRS1975

Fluctuations in O2 stores and gas exchange with passive changes in posture

The purpose of the present study is to determine the effects of changes in posture on oxygen transfer at the mouth and pulmonary capillary membrane and to observe concomitant subtle changes in ventilation under specified assumptions. Breath-by-breath calculations are carried out with a box-balloon spirometer and mass spectrometer. Measurements are made before, during, and after passive tilt to 60 deg and on return to recumbency after 10 min erect. It is found that from supine to upright oxygen stores in the lung increases rapidly and oxygen stores in the blood drops slowly, creating a net deficit in oxygen transfer at the mouth of 130 ml in 10 min. Changes in oxygen stores in the blood result from shifts in blood volume and flow more than from changes in cardiac output. Refilling of oxygen stores in the blood is found to cause transient hypoxia with substantial hyperpnea.

Loeppky, J. A.↗
NASA NTRS1977

Effects of external stores on the air combat capability of a delta wing fighter

Delta wing point-design fighters with two pylon mounted missiles and aft tail controls (similar to several Soviet designs) have been investigated for a Mach number range from about 0.6 to 2.0. Whereas minimum drag penalties that are expected with the addition of external stores do occur, the effects at higher lifts, corresponding to maneuvering flight, are less severe and often favorable. The drag-due-to-lift factor is less with stores on although the lift curve slope is unaffected. The longitudinal stability level is reduced by the addition of stores while the pitch control effectiveness is unchanged. The directional stability was generally reduced at subsonic speeds and increased at supersonic speeds by the addition of stores but sufficiently high stability levels are obtainable that are compatible with the longitudinal maneuvering limits. Some examples of the potential maneuvering capability in terms of normal acceleration and turn radius are included.

Spearman, M. L.↗
NASA NTRS1980

Effect of a flexibly mounted store on the flutter speed of a wing

A passive system proposed for increasing the flutter speed of a wing with heavy concentrated weights involves the concept of mounting the store on a pitch pivot having a very low pitch stiffness relative to the wing stiffness. This concept was investigated utilizing a two dimensional approach involving 4 degrees of freedom, namely, wing bending, wing torsion, store pitch and store vertical translation. This preliminary analysis was very encouraging and the results demonstrate that, if the uncoupled store pitch frequency was below the wing bending frequency, the flutter speed was greatly increased. A second more complete analysis was developed utilizing a three dimensional structure, but retaining the two dimensional, incompressible unsteady airforces of Theodorsen. The details of the analysis are included.

Runyan, H. L.↗
NASA NTRS1986

Unsteady transonics of a wing with tip store

The presence of tip stores influences both the aerodynamic and the aeroelastic performance of wings. Such effects are more pronounced in the transonic regime. In this study, a theoretical method is developed, for the first time, to compute unsteady transonics of oscillating wings with tip stores. The method is based on the small-disturbance, aerodynamic equations of motion from the potential-flow theory. To validate the method, subsonic and transonic aerodynamic computations are made for a lower-aspect-ratio wing, and they are compared with the available experimental data. Comparisons are favorable. The strong effects of the tip store on the transonic aerodynamics of the wing are also illustrated. The method developed in this steady can be used for transonic, aeroelastic computations of wings with tip stores.

Guruswamy, G. P.↗
NASA NTRS1986

Aeroelastic tailoring of composite wings with external stores

The use of an integrating matrix solution procedure allows the aeroelastic stability of a large number of wing/store combinations to be studied with relative speed and accuracy. Results are presented which show the effects of tailoring the orientation of the plies of laminated composite wings when external stores are present. The stores utilized take the form of concentrated masses that are varied in terms of size and location, and combinations of stores are also studied. It is seen that there are cases for which small changes in the laminate can produce large changes in the aeroelastic stability boundary, and for such situations care should be used in tailoring a wing. For a given wing, the choice fiber angle to optimize the aeroelastic performance is quite sensitive to both the size and location of the store.

Green, J. A.↗
NASA NTRS1988

External store carriage loads prediction at transonic speeds

A computational method for prediction of external store carriage loads at transonic speeds is described. The geometric flexibility required for treatment of isolated and underwing, pylon-mounted stores is achieved by computing solutions on a five-level embedded grid arrangement. A completely automated grid generation procedure facilitates applications. Store modeling capability consists of bodies of revolution with multiple fore and aft fins. A body-conforming grid improves the accuracy of the computed store body flow field. A nonlinear finite difference relaxation scheme, developed specifically for modified transonic small disturbance flow equations, enhances numerical stability and accuracy. As a result, more accurate treatment of low aspect ratio, highly swept and tapered wing planforms is possible. A limited supersonic freestream capability is also provided. Pressure, load distribution, force and moment correlations show good agreement for several test cases.

Rosen, Bruce S.↗
NASA NTRS1989

Method to predict external store carriage loads at transonic speeds

A computational method for prediction of external store carriage loads at transonic speeds is described. The geometric flexibility required for treatment of isolated and underwing, pylon mounted stores is achieved by computing solutions on a five level embedded grid arrangement. A completely automated grid generation procedure facilitates applications. Store modeling capability consists of bodies of revolution with multiple fore and aft fins. A body conforming grid improves the accuracy of the computed store body flow field. A nonlinear finite difference relaxation scheme, developed specifically for modified transonic small disturbance flow equations, enhances numerical stability and accuracy. As a result, more accurate treatment of low aspect ratio, highly swept and tapered wing planforms is possible. A limited supersonic freestream capability is also provided. Pressure, load distribution, force and moment correlation show good agreement for several test cases.

Rosen, Bruce S.↗
NASA NTRS1991

Tangential, semisubmerged, and internal store carriage and separation at supersonic speeds

This paper presents a general overview of experimental research conducted in the area of tangential, semisubmerged, and internal store carriage and separation at supersonic speeds. Some of the advantages and disadvantages of tangential and semisubmerged carriage are presented along with a discussion of the interference effects between stores mounted in various arrays. Also included is a review of cavity flow fields that exist at supersonic speeds and a discussion of the effect of cavity size and cavity doors on the separation characteristics of stores. Finally, three passive venting systems are described which can modify the flow field of certain cavities and thus improve the separation characteristics of stores from those cavities.

Wilcox, Floyd J., Jr.↗
NASA NTRS1990

Helicopter in-flight stores jettison

A helicopter emergency external-stores jettison system accommodating an experimental simplified mounting system is presented. The system's conceptual approach is described, including store interface, attachment, functional mechanisms, and system initiation. It is novel both in the stores' mounting interface logic and in the modifications to existing technology for the components. Two nonfragmenting 'ridge cut' explosive bolts were mounted in each 600-pound store to interface with a simple plate on the aircraft. Starting designs with proven technology and functional margins were demonstrated by analysis and test through the design and development. Design details of the system's components, from the explosive bolt to the initiation handle, are described.

Bement, Laurence J.↗
NASA NTRS1992

Tangential, semisubmerged, and internal store carriage and separation

Accounts are presented of tangential, semisubmerged, and internal store carriage drag, as well as of the results to date of stores-separation investigations employing both computational and experimental methods. It is demonstrated that CFD can contribute to the data base needed for internal stores carriage design and trade studies. Attention is given to the case of an internally carried store separating from its bay at supersonic speeds, where various kinds of interference are encountered. A code is developed for the simulation of these unsteady flows through time-accurate computations; computation results are noted to closely reproduce experiment data.

Wilcox, Floyd J., Jr.↗
NASA NTRS1990

Experimental measurements of internal store separation characteristics at supersonic speeds

This paper presents a summary of the experimental supersonic store separation studies that have been conducted at the NASA Langley Research Center. These studies have included investigations of rectangular box cavity flowfields, store separation tests of missiles from various cavity configurations, and tests of a passive venting system for improving the separation characteristics of stores from shallow cavities. Selected results from these investigations are presented which illustrate the types of cavity flowfields that exist at supersonic speeds and the effect of these flowfields and various cavity configurations on the separation characteristics of stores.

Wilcox, Floyd J., Jr.↗