Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface morphologies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Surface morphology of molecular-beam epitaxially grown Si(1-x)Ge(x) layers on (100) and (110) Si

The surface morphology and dislocation structure of Si(1-x)Ge(x) layers grown on (100) and (110) Si substrates have been investigated using atomic force microscopy, and scanning and transmission electron microscopy. The layers, which have up to a 1.2 percent lattice mismatch with the substrates, were grown by molecular-beam epitaxy at 550 C at thicknesses above those required for the introduction of dislocations. Si(1-x)Ge(x) layers grown on (100) show a crosshatch morphology which is correlated to the underlying misfit dislocation network. Annealing greatly enhances the surface roughness producing a partial islanding growing on the preexisting crosshatch morphology. On the (110) substrates no annealing is necessary to produce a roughened surface. The roughened surface morphology is analyzed as a strain-reducing growth mode which enables partial relaxation of the near-surface atomic planes.

Pike, W. T.↗

Investigation on effects of surface morphologies on response of LPG sensor based on nanostructured copper ferrite system

Graphical abstract: Figure shows the variations in resistance with time for copper ferrite system synthesized in various molar ratio. A maximum variation in resistance was observed for copper ferrite prepared in 1:1 molar ratio. Highlights: ► Evaluation of structural, optical and surface morphologies. ► Significant variation in LPG sensing properties. ► Surface modification of ferric oxide pellet by copper ferrite. ► CuFe{sub 2}O{sub 4} pellets for LPG sensing at room temperature. -- Abstract: Synthesis of a copper ferrite system (CuFe{sub 2}O{sub 4}) via chemical co-precipitation method is characterized by X-ray diffraction, surface morphology (scanning electron microscope) and optical absorption spectroscopy. These characteristics show their dependence on the relative compositions of the two subsystems. They are further confirmed by the variation in the band gap. A study of gas sensing properties shows the spinel CuFe{sub 2}O{sub 4} synthesized in 1:1 molar ratio exhibit best response to LPG adsorption/resistance measurement. Thus resistance based LPG sensor is found robust, cheap and may be applied for kitchens and industrial applications.

36 MATERIALS SCIENCE↗

The Effect of Crystallographic Orientation and Nanoscale Surface Morphology on Poly -Si/SiO x Contacts for Silicon Solar Cells

High-efficiency crystalline silicon (Si) solar cells require textured surfaces for efficient light trapping. However, passivation of a textured surface to reduce carrier recombination is difficult. Here, we related the electrical properties of cells fabricated on a KOH-etched, random pyramidal textured Si surface to nanostructure of the passivated contact and the textured surface morphology. The effects of both microscopic pyramidal morphology and nanoscale surface roughness on passivated contacts consisting of a polycrystalline Si (poly-Si) deposited on top of an ultrathin, 1.5-2.2 nm, SiO x layer is investigated. Using atomic force microscopy we show a pyramid face, which is predominantly a Si(111) plane to be significantly rougher than a polished Si(111) surface. This roughness results in a nonuniform SiOx layer as determined by transmission electron microscopy (TEM) of a poly-Si/SiO x contact. Our device measurements also show an overall more resistive, and hence thicker SiO x layer over the pyramidal surface as compared to a polished Si(111) surface, which we relate to increased roughness. Using electron-beam-induced current measurements of poly-Si/SiO x contacts we further show that the SiO x layer near the pyramid valleys is preferentially more conducting, and hence likely thinner than over pyramid tips, edges and faces. Hence, both the microscopic pyramidal morphology and nanoscale roughness lead to nonuniform SiO x layer, thus leading to poor poly-Si/SiO x contact passivation. Finally, we report >21% efficient and =80% fill factor front/back poly-Si/SiO x solar cells on both single-side and double-side textured wafers without the use of transparent conductive oxide layers and show that the poorer contact passivation on a textured surface is limited to boron-doped poly-Si/SiO x contacts.

14 SOLAR ENERGY↗

Retention and surface morphology evaluation of fine-grain dispersion-strengthened tungsten for plasma-facing component applications

This study exposed novel fine-grain dispersion-strengthened tungsten (W) to high fluence, low energy deuterium (D) and helium (He) plasmas to evaluate how material microstructure and composition affect hydrogen retention and surface morphology. Tested materials included fine-grain dispersion-strengthened tungsten (DSW) with 3 wt% zirconium carbide (ZrC) dispersoids, fine-grain dense W without any dispersoids (FGW), and coarse-grained polycrystalline ‘ITER-grade’ W. Samples were exposed to D 2 + and He + plasmas at fusion-relevant fluences (∼10 25 m -2 ) and ion energies (75 eV) over a range of temperatures (200 °C, 300 °C, 450 °C for D, 850 °C for He). Helium ion microscopy was performed on the exposed samples to evaluate surface morphology changes and material integrity. After D plasma exposure, the ZrC dispersoids showed near-surface degradation at exposure temperatures above 300 °C, but no detrimental morphology changes were observed for the adjacent W grains. After He plasma-exposure, nano-structured fuzz formation was observed in the tungsten matrix of all samples. The ZrC dispersoids maintained their integrity despite the surrounding fuzz growth, with clear delineation between the W fuzz and dispersoid regions. Thermal desorption spectroscopy showed that ZrC DSW consistently retained more D than the FGW by about a factor of 2 across all temperatures. At 200 °C and 300 °C, the ITER-W displayed lower D retention than both the DSW and FGW, however at 450 °C ITER-W showed the highest retention, about 50% more than DSW. He retention was comparable across all samples, with the highest retention observed in the fine-grain W, only 26% higher than in ITER-W. These insights on retention behavior will inform further optimization of these novel fine-grained tungsten materials with and without dispersoid additives.

Dispersion-strengthened tungsten↗

Effect of homolog doping on surface morphology and mass-loss rates from PETN crystals. Studies using atomic force microscope and thermo-gravimetric analysis

Pentaerythritol tetranitrate (PETN) is an important energetic material and its performance as a secondary explosive depends strongly on the density as well as flow porosity of powdered material, which in turn is governed by the size and surface properties of the PETN crystallite particles. Historically there has been evidence that the surface properties of PETN particles can be strongly influenced by the presence of homolog impurities of PETN, in particular, dipentaerythritol hexanitrate (diPEHN) and tripentaerythritol octanitrate (triPEON), although not many systematic studies characterizing such influence exist. In this work we employ thermogravimetric analysis (TGA) to measure mass-loss rates at elevated temperatures and show that doping with a small amount of diPEHN and triPEON can reduce the mass-loss rate from PETN single-crystal surfaces by as much as 35 % as compared to undoped crystals. Arrhenius plots of mass-loss rates as a function of temperature suggest that the reduction in evaporation is not due to the change in activation barrier of the molecular evaporation process, but perhaps due to the impedance to the receding motion of the steps by the immobile impurities on the surface. Removal of surface impurities through gentle washing with ethanol leads to enhanced mass-loss rate relative to pure PETN suggesting a roughened surface morphology. Some surface roughening in doped crystals is supported by Atomic force microscopy (AFM) images of growth layers that show evidences of growth layer stacking and rough edges. Furthermore, we find that a larger amount of impurity added to the original solution does not necessarily lead to a more highly doped crystal, which could perhaps be interpreted as PETN crystals being able to accommodate only up to a certain weight percent of homolog impurities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Phosphorus incorporation during Si(001):P gas-source molecular beam epitaxy: Effects on growth kinetics and surface morphology

The effects of P doping on growth kinetics and surface morphological evolution during Si(001):P gas-source molecular beam epitaxy from Si{sub 2}H{sub 6} and PH{sub 3} at temperatures T{sub s}=500-900 deg. C have been investigated. With increasing PH{sub 3}/Si{sub 2}H{sub 6} flux ratio J{sub P/Si} at constant T{sub s}, we observe a decrease in the film growth rate R and an increase in the incorporated P concentration C{sub P}, both of which tend toward saturation at high flux ratios, which is accompanied by increased surface roughening and pit formation. At constant J{sub P/Si}, R increases with increasing T{sub s}, while C{sub P} initially increases, reaches a maximum at T{sub s}=700 deg. C, and then decreases at higher growth temperatures. We use in situ isotopically tagged D{sub 2} temperature programed desorption (TPD) to follow changes in film surface composition and dangling bond density {theta}{sub db} as a function of J{sub P/Si} and T{sub s}. Measurements are carried out on both as-deposited Si(001):P layers and P-adsorbed Si(001) surfaces revealing {beta}{sub 1} and {beta}{sub 2} peaks due to D{sub 2} desorption from Si monohydride and dihydride species, respectively, as well as the formation of a third peak {beta}{sub 3} corresponding to D{sub 2} desorption from mixed Si-P dimers. Dissociative PH{sub 3} adsorption on Si(001) results in a decrease in {theta}{sub db} and an initial increase in P surface coverage {theta}{sub P} with increasing T{sub s}. Saturation {theta}{sub P} values reach a maximum of {approx}1 ML at T{sub s}=550 deg. C, and decrease with T{sub s}>600 deg. C due to the onset of P{sub 2} desorption. Comparison of {theta}{sub P}(T{sub s}) results obtained during film growth with postdeposition C{sub P}(T{sub s}) results reveals the presence of strong P surface segregation. From measurements of {theta}{sub P} versus C{sub P} in Si(001):P layers grown as a function of T{sub s}, we obtain a P segregation enthalpy {delta}H{sub s}=-0.86 eV. By using the combined set of results, we develop a predictive model for C{sub P} versus T{sub s} and, J{sub P/Si} incorporating the dependence of the PH{sub 3} reactive sticking probability S{sub PH{sub 3}} on {theta}{sub P}, which provides an excellent fit to the experimental data.

36 MATERIALS SCIENCE↗

Effect of annealing temperature on the surface morphology and electrical properties of aluminum doped zinc oxide thin films prepared by sol-gel spin-coating method

Aluminum doped zinc oxide thin films were prepared through sol gel and spin coating technique from zinc acetate dihydrate and aluminum nitrate nanohydrate in alcoholic solution. The electrical properties and surface morphology study are investigated for the thin films annealed at 350{approx}500 deg. C. Zinc oxide thin films deposited on glass and silicon substrates were characterized using electron microscopy (SEM) and current-voltage (I-V) measurement scanning for surface morphology and electrical properties study respectively. The SEM investigation shows that zinc oxide thin films are denser at higher annealing temperature. The result indicates electrical properties of aluminum doped zinc oxide thin films are improved with annealing temperatures. The resistivity of aluminum doped zinc oxide thin films are decreased with annealing temperature up to 500 deg. C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Surface morphology and electrical transport of rapid thermal annealed chromium-doped indium zinc oxides: The influence of zinc interstitials and out-diffusion

We investigate the complex impedance (CI) spectra of chromium-doped indium zinc oxide (CIZO) films with different rapid thermal annealing (RTA) temperatures. The CI spectra drawn from the impedance contributions of Zn-O and In-O bondings in CIZO films were analyzed by two sets of parallel resistance and capacitance components in series. The result demonstrates that zinc interstitials controls electron concentration and transition of electrical transport from semiconducting to metallic. At higher RTA temperature, high-density zinc interstitial promotes Zn atom diffusion from the surface, modifying surface morphology.

36 MATERIALS SCIENCE↗

Effect of annealing on the growth dynamics of ZnPc LB thin film and its surface morphology

The ZnPc molecules in the thin film prepared by Langmuir-Blodgett (LB) process in asdeposited state has been found to have an edge on orientation with average tilt angle of 64.3 ° as confirmed from the Pressure-Area (π-A) isotherm and X-ray diffraction (XRD) study. The ZnPc LB thin film has been observed to have abnormal growth mode at higher annealing temperature and it is mainly driven by minimization of surface free energy which lead to large increase in crystallinity of the film. Kinetically favored orientational and structural transitions of ZnPc thin film during annealing and their effect on the surface morphology of the thin film has been studied using scaling concepts. The scaling exponents 1) root mean square (RMS) roughness σ, 2) roughness exponent α and, 3) in plane correlation length ξ are calculated from the HDCF g(r) and ACF C(r). The RMS surface roughness σ is found to be dependent on the as defined short wavelength undulations (ρ) and long wavelength undulations (χ). Both ρ and χ are the function of all the three scaling exponents. σ has been observed to be maximum for the ZnPc thin film annealed at 290 °C, since the χ shoot to maximum value at this temperature due to the formation of small domains of ZnPc nanorods. The self affinity of the ZnPc thin film is found to decrease on annealing as obtained from both power spectral density (PSD) and HDCF g(R) and ACF C(R) study, which confirms that the dimension of surface morphology of the ZnPc LB thin film transform towards 2D with increase in annealing temperature.

36 MATERIALS SCIENCE↗

Influence of heavier impurity deposition on surface morphology development and sputtering behavior explored in multiple linear plasma devices

Surface morphology development and sputtering behavior of Cr, as a test material, have been explored under He plasma exposure at a low incident ion energy of ~80 eV in multiple linear plasma devices: PISCES-A, PSI-2, and NAGDIS-II. From comparison of the experiments in these devices, deposition of a small amount of heavier impurities (Mo in NAGDIS-II and Ta in PISCES-A) onto Cr is found to result in the formation of cone structures on the Cr surface due to preferential sputtering, resulting in a significant reduction (up to ~10 times) in the sputtering yield of Cr due to line-of-sight redeposition onto the neighboring cones. The heavier impurities are thought to originate from a sample holding cap/cover, which can be sputtered by a trace amount of intrinsic impurities (C, O, etc) as well as by Cr ionized in the plasma. It can be concluded from the Cr experiments, as well as additional Be data collected in PISCES-B, that heavier impurity deposition plays a major role in the cone structure formation, while other mechanisms (e.g. surface irregularity and oxide) also exist.

36 MATERIALS SCIENCE↗

Surface Morphology and Topology of TiO{sub 2} Nanocoating on Metal Substrates at Different Molar Concentrations and Speed

Mild steel is low carbon steel content of carbon less than 0.25 wt%. This type of steels is low cost to produce while has good toughness and outstanding ductility. Nanocoated mild steel surface is greatly many applications such as in automobile body component, pipelines, wall of operation's room and operation's theatre. Anatase TiO{sub 2} coating were successfully synthesized by optimize the sol-gel solution wherein glacial acetic acid and controlling of annealing temperature. In this paper initial study of TiO{sub 2} nanocoating on mild steel surface was presented. TiO{sub 2} nanocoating was prepared by spin coating technique. Spin coating technique is low processing temperature and ease of compositional modifications. The sol-gel concentration and speed (rpm) of spin coating were varied to produce different surface morphology and topology of samples. The surface phase, morphology and topology of coating were investigated by X-ray diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM) and Atomic Force Microscopy (AFM) while the roughness of coating was determined by Surface Profiler (SP).

36 MATERIALS SCIENCE↗

Metalorganic chemical vapor deposition of ZnGeN 2 films on GaN: effects of cation stoichiometry on surface morphology and crystallinity

Novel optoelectronic device designs based on the heterostructures of III-N and II-IV-N 2 are promising to advance device performance significantly. For example, by utilizing InGaN-ZnGeN 2 quantum well (QW) structures instead of pure InGaN, the band structure engineering in the QW active region can lead to improved electron-hole wavefunction overlap, and thus enhance the radiative efficiency for photon generation. These novel heterostructures have great potential to address the current challenge of low quantum efficiency in InGaN QW based light emitting diodes emitting in green and beyond. The materials development of ZnGeN 2 is still at an early stage as compared to the much matured GaN material system. In an ideal octet rule preserving ordered structure of ZnGeN 2 , every N atom is coordinated by exactly two Zn and two Ge atoms. However, local violation of octet rule can be caused by non-ideal coordination of N by the cations. The disordered structure is thermodynamically less favorable but can still be achieved, for example, in kinetics-limited growth regime. The ordered ZnGeN 2 has a bandgap very close to that of GaN (~3.4 eV) and a lattice mismatch of <0.1% with GaN. Interestingly, the valence band of ZnGeN 2 has been predicted to be ~1 eV above that of GaN, which has inspired novel designs for high efficiency light emitters. In this work, we investigated the metalorganic chemical vapor deposition (MOCVD) of ZnGeN 2 films on GaN/c-sapphire templates. Diethylzinc (DEZn), germane (GeH4) and ammonia were used as the precursors for Zn, Ge and N, respectively. A systematic study was conducted to investigate the cation stoichiometry as a function of growth temperature (TG), total reactor pressure (P) and DEZn/GeH 4 molar flow rate ratio (RII/IV). Under the investigated growth window, the Zn/(Zn+Ge) composition in the films, determined from energy dispersive X-ray spectroscopy, decreased monotonically with increase in TG but increased with increase in P and RII/IV. Atom probe tomography data did not indicate the presence of any secondary phases such as Zn 3 N 2 or Ge 3 N 4 . The surface morphology and crystallinity of the grown films had strong correlation with the Zn/(Zn+Ge) composition. The scanning electron microscopy images showed that the near-stoichiometric films have planar surfaces whereas Zn-rich films had crystallites on their surface and the Zn-poor films had faceted surface. Scanning transmission electron microscopy (STEM) imaging revealed that the Zn-rich and Zn-poor films have columnar and filament-like morphology, respectively, whereas the near-stoichiometric films have continuous film-like cross-sectional morphology. TEM nano-diffraction patterns as well as X-ray diffraction 2θ-ω scan profiles indicate that the near stoichiometric films are single crystalline. Nano-diffraction pattern of the stoichiometric films resembled that of a disordered ZnGeN 2 structure. Room temperature Raman spectra of near-stoichiometric films showed only the phonon density of states like features of a cation disordered ZnGeN 2 . Cathodoluminescence and photoluminescence spectra measured at different temperatures had similar features with peak emission wavelength at ~ 2 eV. In conclusion, the stoichiometry of ZnGeN 2 films can be widely tuned by tuning the MOCVD growth parameters. The surface morphology and the crystallinity of the films were found to have strong correlation with the Zn/(Zn+Ge) composition. The stoichiometric ZnGeN 2 films grown on GaN were demonstrated with uniform surface morphology and high crystalline quality. The results from this work will provide pathway to implement ZnGeN 2 in device structures.

Karim, Md Rezaul↗

Structure and features of the surface morphology of A{sup 4}B{sup 6} chalcogenide epitaxial films

The structure and features of the surface morphology of Pb{sub 1-x}Mn{sub x}Se (x = 0.03) epitaxial films grown on freshly cleaved BaF{sub 2}(111) faces and PbSe{sub 1-x}S{sub x}(100) (x = 0.12) single-crystal wafers were investigated by molecular beam condensation and the hot-wall method. It is shown that the epitaxial films, in accordance with the data in the literature for other chalcogenides, grow in the (111) and (100) planes, repeating the substrate orientation. Black aggregates are observed on the film surface of the films grown. The results obtained are compared with the data in the literature and generalized for other chalcogenides: A{sup 4}B{sup 6}:Pb (S, Se, Te); Pb{sub 1-x}Sn{sub x} (S, Se, Te); and Pb{sub 1-x}Mn (Se, Te). It is established that the formation of black aggregates, which are second-phase inclusions on the surface of epitaxial films obtained by vacuum thermal deposition, is characteristic of narrow-gap A{sup 4}B{sup 6} chalcogenides.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Interrelation of the construction of the metamorphic InAlAs/InGaAs nanoheterostructures with the InAs content in the active layer of 76-100% with their surface morphology and electrical properties

The influence of the construction of a metamorphic buffer on the surface morphology and electrical properties of InAlAs/InGaAs/InAlAs nanoheterostructures with InAs content in the active layer from 76 to 100% with the use of the GaAs and InP substrates is studied. It is shown that such parameters as the electron mobility and the concentration, as well as the root-mean-square surface roughness, substantially depend on the construction of the metamorphic buffer. It is established experimentally that these parameters largely depend on the maximal local gradient of the lattice constant of the metamorphic buffer in the growth direction of the layers rather than on its average value. It is shown that, with selection of the construction of the metamorphic buffer, it is possible to form nanostructured surfaces with a large-periodic profile.

36 MATERIALS SCIENCE↗

Electrical and Surface Morphology of Polyvinylchloride Composites Filled with Aluminum Powder

In this work, the electrical and surface morphology of polyvinyl chloride (PVC) composites filled with different concentration of aluminum powder varying from 0 to 40 wt.% have been prepared by solution costing method. The electrical conductivity of these composites were investigated in the frequency range 100 Hz-10 MHz at room temperature. The conductivity of the composites system exhibited a strong frequency dependence particularly in the vicinity of percolation threshold (20 wt.%). It was observed that the electrical conductivity gradually increased with filler concentration and frequency and explained in terms of hopping conduction mechanism. The electrical conductivity of the composites obeys universal power law (i.e. {sigma} = Af{sup n}), where, n is power exponent. The scanning electron microscope (SEM) micrographs indicate the agglomeration of aluminum particles dispersed within the PVC at the higher aluminum concentration, yielding a conductive path through the composites. It is also corroborated with electrical conductivity result.

36 MATERIALS SCIENCE↗

Studying femtosecond-laser hyperdoping by controlling surface morphology

We study the fundamental properties of femtosecond-laser (fs-laser) hyperdoping by developing techniques to control the surface morphology following laser irradiation. By decoupling the formation of surface roughness from the doping process, we study the structural and electronic properties of fs-laser doped silicon. These experiments are a necessary step toward developing predictive models of the doping process. We use a single fs-laser pulse to dope silicon with sulfur, enabling quantitative secondary ion mass spectrometry, transmission electron microscopy, and Hall effect measurements. These measurements indicate that at laser fluences at or above 4 kJ m{sup -2}, a single laser pulse yields a sulfur dose >(3 {+-} 1) x 10{sup 13} cm{sup -2} and results in a 45-nm thick amorphous surface layer. Based on these results, we demonstrate a method for hyperdoping large areas of silicon without producing the surface roughness.

36 MATERIALS SCIENCE↗

Effect of anion-to-cation supplying ratio on the surface morphology of AlN films grown on ZnO substrates at low temperature

The authors investigated the evolution of surface morphology of AlN films grown on ZnO substrates at low temperature (LT) (400 deg. C) as a function of anion/cation supplying ratio (V/III ratio). Unlike the well-known favorable growth conditions for high-temperature growth, smooth-surface LT-AlN layers were obtained under the O-polar surface, stoichiometric, and N-rich conditions. LT-AlN layers revealed smooth surface (roughness in root mean square=0.20 nm for AlN on O-polar ZnO and 0.44 nm for AlN on Zn-polar ZnO) and quite low etch-pit density ({approx}2x10{sup 6} cm{sup -2} for AlN/Zn-polar ZnO).

36 MATERIALS SCIENCE↗

Transition Behavior of Surface Morphology Evolution of Si(100) During Low-Energy Normal-Incidence Ar+ Ion Bombardment

The temperature dependence of the surface morphology evolution during 1000 eV Ar{sup +} ion bombardment of Si(100) surfaces at normal incidence is studied in real time. At room temperature the surface is amorphized by the ion bombardment but remains smooth. Calculations suggest this may be due to ion impact induced lateral mass redistribution. However, at the fluxes used here, surface roughening occurs above 400 C, and in the range of 400 C to 500 C a transition region from amorphous to crystalline surface is observed. Above 500 C, the surface remains crystalline and the growing corrugations exhibit dynamic scaling with power law growth in amplitude and characteristic length scale. This behavior is characteristic of instabilities driven by surface diffusion processes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗