Results for “tall tower” — Page 3

NASA NTRS2025

Structural Sizing of a 50-m-Tall Thermoplastic Composite Truss Tower Structure for the Lunar South Pole

At the lunar south pole, solar arrays elevated by truss towers are exposed to near continuous sunlight since the sun remains near the horizon. Recent studies suggest that tower heights on the order of 50 m are needed to meet the power requirements to support a sustained lunar presence. While eventually towers may be constructed using materials sourced in-situ, initially structural elements will likely be brought from the Earth, deployed, and assembled. Thermoplastic composites offer the benefit of high specific stiffness and strength properties along with welding for assembly joints, and therefore represent a promising material system for this application. The focus of this paper is on the structural sizing of such towers. A set of expressions based on beam theory are presented for preliminary sizing of the truss tower structure for strength and buckling. The loading condition that drives sizing is base excitation resulting from moonquakes. A point design, developed through finite element analysis, verifies the analytical sizing routine and shows the importance of joints. The results show a viable point design and highlight the factors most significant in the structural sizing.

Thermoplastic composites↗

NASA NTRS2008

Solar Tower Experiments for Radiometric Calibration and Validation of Infrared Imaging Assets and Analysis Tools for Entry Aero-Heating Measurements

The NASA Engineering and Safety Center sponsored Hypersonic Thermodynamic Infrared Measurements assessment team has a task to perform radiometric calibration and validation of land-based and airborne infrared imaging assets and tools for remote thermographic imaging. The IR assets and tools will be used for thermographic imaging of the Space Shuttle Orbiter during entry aero-heating to provide flight boundary layer transition thermography data that could be utilized for calibration and validation of empirical and theoretical aero-heating tools. A series of tests at the Sandia National Laboratories National Solar Thermal Test Facility were designed for this task where reflected solar radiation from a field of heliostats was used to heat a 4 foot by 4 foot test panel consisting of LI 900 ceramic tiles located on top of the 200 foot tall Solar Tower. The test panel provided an Orbiter-like entry temperature for the purposes of radiometric calibration and validation. The Solar Tower provided an ideal test bed for this series of radiometric calibration and validation tests because it had the potential to rapidly heat the large test panel to spatially uniform and non-uniform elevated temperatures. Also, the unsheltered-open-air environment of the Solar Tower was conducive to obtaining unobstructed radiometric data by land-based and airborne IR imaging assets. Various thermocouples installed on the test panel and an infrared imager located in close proximity to the test panel were used to obtain surface temperature measurements for evaluation and calibration of the radiometric data from the infrared imaging assets. The overall test environment, test article, test approach, and typical test results are discussed.

Splinter, Scott C.↗

NASA NTRS2003

Warm Core Structure of Hurricane Erin Diagnosed from High Altitude Dropsondes during CAMEX-4

A combination multi-aircraft and several satellite sensors were used to examine the core of Hurricane Erin on September 10, 2001, as part of the CAMEX4 program. During the first set of aircraft passes, around 1700 UTC, Erin was still at its maximum intensity with a central pressure of 969 hpa and windspeed of 105 kts (54 m/s). The storm was moving slowly northwestward at 4 m/s, over an increasingly colder sea surface. Three instrumented aircraft, the NOAA P3 with radar, the NASA ER- 2 at 19 km, newly equipped with GPS dropwindsondes, and the NASA DC-8 with dropwindsondes flew in formation across the eye at about 1700 UTC and again 2.5 hrs later around 1930 UTC. The storm had weakened by 13 m/s between the first and second eye penetrations. The warm core had a maximum temperature anomaly of only 11 C, located at 500 hpa, much weaker and lower than active hurricanes. The core appeared to slant rearward above 400 hpa. Even on the first penetration, airborne radar showed that the eye wall cloud towers were dying. The tops fell short of reaching 15 km and a melting band was found throughout. The tropopause had a bulge to 15.8 km elevation (environment approx. 14.4 km) above the dying convection. A feature of Erin at this timt was a pronounced wave-number-one convective asymmetry with all convective activity being confined to the forward quadrants on the left side of the shear vector as calculated from analyses. This is similar to that predicted by the mesoscale numerical models, which also predict that such small amounts of shear would not affect the storm intensity. In Erin, it is remarkable that relatively small shear produced such a pronounced asymmetry in the convection. In addition, horizontal asymmetries in the low-level warm core were identified. Almost certainly, the colder ocean would kill the tall convective towers feeding the warm core, even if wind shear were absent.

Halverson, J. B.↗

NASA NTRS1983

Sphere forming method and apparatus

A system is provided for forming small accurately spherical objects. Preformed largely spherical objects are supported at the opening of a conduit on the update of hot gas emitted from the opening, so the object is in a molten state. The conduit is suddenly jerked away at a downward incline, to allow the molten object to drop in free fall, so that surface tension forms a precise sphere. The conduit portion that has the opening, lies in a moderate vacuum chamber, and the falling sphere passes through the chamber and through a briefly opened valve into a tall drop tower that contains a lower pressure, to allow the sphere to cool without deformation caused by falling through air.

Youngberg, C. L.↗

NASA NTRS1993

The Iridium (tm) system: Personal communications anytime, anyplace

The Iridium system is designed to provide handheld personal communications between diverse locations around the world at any time and without prior knowledge of the location of the personal units. This paper provides an overview of the system, the services it provides, its operation, and an overview of the commercial practices and relatively high volume satellite production techniques which will make the system cost effective. A constellation of 66 satellites will provide an orbiting, spherical-shell, infrastructure for this global calling capability. The satellites act as tall cellular towers and allow convenient operation for portable handheld telephones. The system will provide a full range of services including voice, paging, data, geolocation, and fax capabilities. Motorola is a world leader in the production of high volume, high quality, reliable telecommunications hardware. One of Iridium's goals is to apply these production techniques to high reliability space hardware. Concurrent engineering, high performance work teams, advanced manufacturing technologies, and improved assembly and test methods are some of the techniques that will keep the Iridium system cost effective. Mobile, global, flexible personal communications are coming that will allow anyone to call or receive a call from/to anyplace at anytime. The Iridium system will provide communications where none exist today. This connectivity will allow increased information transfer, open new markets for various business endeavors, and in general increase productivity and development.

Hatlelid, John E.↗

NASA NTRS1980

Firefighting Module

Aviation Power Supply's mobile firefighting module called Firefly II is mounted on a trailer pulled by a pickup truck. Trailer unit has two three- inch water cannons, and the pickup carries a six inch cannon. Completely self contained, module pumps 3,000 gallons of water a minute from hydrants or open bodies of water. Stream can go as far as 400 feet or can be employed in a high-loft mode to reach the tops of tall refinery towers. Compact Firefly II weighs only 2,500 pounds when fully fueled. Key component is a specially designed two stage pump. Power for the pump is generated by a gas turbine engine. Module also includes an electronic/pump controller, multiple hose connections, up to 1,500 feet of hose and fuel for four hours operation. Firefly trailer can be backed onto specially-built large fireboat.

Source record↗

NASA NTRS1981

Firefighting Module

Aviation Power Supply's mobile firefighting module called Firefly II is mounted on a trailer pulled by a pickup truck. Trailer unit has two three- inch water cannons, and the pickup carries a six inch cannon. Completely self contained, module pumps 3,000 gallons of water a minute from hydrants or open bodies of water. Stream can go as far as 400 feet or can be employed in a high-loft mode to reach the tops of tall refinery towers. Compact Firefly II weighs only 2,500 pounds when fully fueled. Key component is a specially designed two stage pump. Power for the pump is generated by a gas turbine engine. Module also includes an electronic/pump controller, multiple hose connections, up to 1,500 feet of hose and fuel for four hours operation. Firefly trailer can be backed onto specially-built large fireboat.

Source record↗

NASA NTRS2003

MiniSODAR(TradeMark) Evaluation

This report describes results of the AMU's Instrumentation and Measurement task for evaluation of the Doppler miniSODAR(TradeMark) System (DmSS). The DmSS is an acoustic wind profiler providing high resolution data to a height of approx. 410 ft. The Boeing Company installed a DmSS near Space Launch Complex 37 in mid-2002 as a substitute for a tall wind tower and plans to use DmSS data for the analysis and forecasting of winds during ground and launch operations. Peak wind speed data are of particular importance to Launch Weather Officers of the 45th Weather Squadron for evaluating user Launch Commit Criteria. The AMU performed a comparative analysis of wind data between the DmSS and nearby wind towers from August 2002 to July 2003. The DmSS vertical profile of average wind speed showed good agreement with the wind towers. However, the DMSS peak wind speeds were higher, on average, than the wind tower peak wind speeds by about 25%. A statistical model of an idealized Doppler profiler was developed and it predicted that average wind speeds would be well determined but peak wind speeds would be over-estimated due to an under-specification of vertical velocity variations in the atmosphere over the Profiler.

Short, David A.↗

NASA NTRS2013

Total Lightning Observations within Electrified Snowfall using Polarimetric Radar, LMA, and NLDN Measurements

Four electrified snowfall cases are examined using total lightning measurements from lightning mapping arrays (LMAs), and the National Lightning Detection Network (NLDN) from Huntsville, AL and Washington D.C. In each of these events, electrical activity was in conjunction with heavy snowfall rates, sometimes exceeding 5-8 cm hr-1. A combination of LMA, and NLDN data also indicate that many of these flashes initiated from tall communications towers and traveled over large horizontal distances. During events near Huntsville, AL, the Advanced Radar for Meteorological and Operational Research (ARMOR) C-band polarimetric radar was collecting range height indicators (RHIs) through regions of heavy snowfall. The combination of ARMOR polarimetric radar and VHF LMA observations suggested contiguous layer changes in height between sloping aggregate-dominated layers and horizontally-oriented crystals. These layers may have provided ideal conditions for the development of extensive regions of charge and resultant horizontal propagation of the lightning flashes over large distances.

Schultz, Christopher J.↗

NASA NTRS2012

Implementing the Mars Science Laboratory Terminal Descent Sensor Field Test Campaign

The Mars Science Laboratory (MSL) will deliver a 900 kg rover to the surface of Mars in August 2012. MSL will utilize a new pulse-Doppler landing radar, the Terminal Descent Sensor (TDS). The TDS employs six narrow-beam antennas to provide unprecedented slant range and velocity performance at Mars to enable soft touchdown of the MSL rover using a unique sky crane Entry, De-scent, and Landing (EDL) technique. Prior to use on MSL, the TDS was put through a rigorous verification and validation (V&V) process. A key element of this V&V was operating the TDS over a series of field tests, using flight-like profiles expected during the descent and landing of MSL over Mars-like terrain on Earth. Limits of TDS performance were characterized with additional testing meant to stress operational modes outside of the expected EDL flight profiles. The flight envelope over which the TDS must operate on Mars encompasses such a large range of altitudes and velocities that a variety of venues were neces-sary to cover the test space. These venues included an F/A-18 high performance aircraft, a Eurocopter AS350 AStar helicopter and 100-meter tall Echo Towers at the China Lake Naval Air Warfare Center. Testing was carried out over a five year period from July 2006 to June 2011. TDS performance was shown, in gen-eral, to be excellent over all venues. This paper describes the planning, design, and implementation of the field test campaign plus results and lessons learned.

Mars Science Laboratory (MSL)↗

NASA NTRSDate not supplied

Design Development of a Stable, Lightweight, Tall and Self-Deploying Lunar Tower

Deployable composite booms with spaceflight heritage are being investigated at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) and the Massachusetts Institute of Technology (MIT) Space Resources Workshop for their potential to be vertically deployed in the lunar gravity field, in support of the NASA Artemis campaign. This paper reports new design development results—after the original presentation at the NASA 2020 BIG Idea Challenge—for a 16.5-meter-tall, compact, self-deploying composite tower intended to support the exploration of lunar permanently shadowed regions by nearby robotic assets or humans. Possible applications include vertical solar arrays and the provision of elevated lines-of-sight to science or engineering payloads, in support of nearby targets operating in areas of interest that may be hard to reach. Useful elevated payloads include radio repeaters, remote sensing and imaging, navigation and power beaming systems. However, while these lightweight rollable booms have an excellent height to mass ratio, they typically exhibit axial curvature upon deployment resulting in appreciable lateral dead-load deflection of the tip mass relative to the tower base. This static deflection increases with tower height and tip mass, not only constraining the value delivered by the tower but also endangering its integrity. To develop a competitive, lightweight deployable composite boom tower, a capability to correct static deflections during and after deployment will be required. In this paper, a deployable guy wire stability system will be presented for the MIT / LaRC self-erecting composite boom lunar tower that provides real time measurements, maintains tension both actively (during deployment) and passively (post-deployment), and can serve as a reconfigurable platform to test and trade alternative stability system configurations, such as with added spreaders inspired by sailing boat masts. Using a calibrated photogrammetry system, the natural lateral deflection of the boom tip relative to the boom base at different deployed heights was recorded for different configurations. With real-time force measurements it was found that tensioned guy wires can significantly reduce the static tip deflection of a deployable composite boom under dead load and can dampen a dynamic oscillation in under a minute. It was also found that control authority is greatest where it is needed most, i.e., for the lever arm closest to being opposite the direction of deflection. For a tower height of at least 11 m and spreader length of at least 60 cm, a solution of differential tension in all three arms exists and, in principle, provides sufficient control authority to correct or significantly reduce boom tip deflections. Notably, natural deflections occur almost entirely normal to the seams of the boom cross-section, but the natural boom tip lateral deflection under dead load upon deployment was approximately 5% of boom deployed length, exceeding the manufacturing acceptance specification of 1%. Ongoing and future work includes the further investigation towards mitigating manufacture-caused lateral deflection, trading of alternative guy wire system designs, as well as the design development of a second-generation tower incorporating a more capable boom design with the learnings from the proof-of-concept system presented here.

deployable composite boom↗

NASA NTRSDate not supplied

Structural Sizing of a 50-m-Tall Thermoplastic Composite Solar Array Truss Tower Structure for the Lunar South Pole

At the lunar south pole, solar arrays elevated by truss towers are exposed to near continuous sunlight since the sun remains near the horizon. Recent studies suggest that tower heights on the order of 50 m are needed to meet the power requirements to support a sustained lunar presence. While eventually towers may be constructed using materials sourced in-situ, initially structural elements will likely be brought from the Earth, deployed, and assembled. Thermoplastic composites offer the benefit of high specific stiffness and strength properties along with welding for assembly joints, and therefore represent a promising material system for this application. The focus of this paper is on the structural sizing of such towers. A set of expressions based on beam theory are presented for preliminary sizing of the truss tower structure for strength and buckling. The loading condition that drives sizing is base excitation resulting from moonquakes. A point design, developed through finite element analysis, verifies the analytical sizing routine and shows the importance of joints. The results show a viable point design and highlight the factors most significant in the structural sizing.

Thermoplastic composites↗

NASA NTRSDate not supplied

Structural Sizing of a 50-m-Tall Thermoplastic Composite Solar Array Truss Tower Structure for the Lunar South Pole

At the lunar south pole, solar arrays elevated by truss towers are exposed to near continuous sunlight since the sun remains near the horizon. Recent studies suggest that tower heights on the order of 50 m are needed to meet the power requirements to support a sustained lunar presence. While eventually towers may be constructed using materials sourced in-situ, initially structural elements will likely be brought from the Earth, deployed, and assembled. Thermoplastic composites offer the benefit of high specific stiffness and strength properties along with welding for assembly joints, and therefore represent a promising material system for this application. The focus of this paper is on the structural sizing of such towers. A set of expressions based on beam theory are presented for preliminary sizing of the truss tower structure for strength and buckling. The loading condition that drives sizing is base excitation resulting from moonquakes. A point design, developed through finite element analysis, verifies the analytical sizing routine and shows the importance of joints. The results show a viable point design and highlight the factors most significant in the structural sizing.

Thermoplastic composites↗

NASA NTRS2014

Optical Polarization of Light from a Sorghum Canopy Measured Under Both a Clear and an Overcast Sky

Introduction: We tested the hypothesis that the optical polarization of the light reflected by a sorghum canopy is due to a Fresnel-type redirection, by sorghum leaf surfaces, of light from an unpolarized light source, the sun or overcast sky, toward the measuring sensor. If it can be shown that the source of the polarization of the light scattered by the sorghum canopy is a first surface, Fresnel-type reflection, then removing this surface reflected light from measurements of canopy reflectance presumably would allow better insight into the biochemical processes such as photosynthesis and metabolism that occur in the interiors of sorghum canopy leaves. Methods: We constructed a tower 5.9m tall in the center of a homogenous sorghum field. We equipped two Barnes MMR radiometers with polarization analyzers on the number 1, 3 and 7 Landsat TM wavelength bands. Positioning the radiometers atop the tower, we collected radiance data in 44 view directions on two days, one day with an overcast sky and the other, clear and sunlit. From the radiance data we calculated the linear polarization of the reflected light for each radiometer wavelength channel and view direction. Results and Discussion: Our experimental results support our hypothesis, showing that the amplitude of the linearly polarized portion of the light reflected by the sorghum canopy varied dramatically with view azimuth direction under a point source, the sun, but the amplitude varied little with view azimuth direction under the hemispherical source, the overcast sky. Under the clear sky, the angle of polarization depended upon the angle of incidence of the sunlight on the leaf, while under the overcast sky the angle of polarization depended upon the zenith view angle. These results support a polarized radiation transport model of the canopy that is based upon a first surface, Fresnel reflection from leaves in the sorghum canopy.

cloud cover↗

NASA NTRS2017

Transformers for Lunar Extreme Environments: Ensuring Long-Term Operations in Regions of Darkness and Low Temperatures: II - Phase

This report shows how solar power could enable robotic operations in permanently shaded regions at lunar poles, to extract water ice and further produce liquid hydrogen and oxygen (LH2/LO2) propellant. The power needs are derived from an Architecture for Human Exploration of Mars based entirely on lunar propellant. The extraction of 10 metric tons of water per day (at 10% water in regolith) requires approx. 0.6 MW thermal power. Additional approx. 2 MW electric power are required to produce 7.5 metric tons of LH2/LO2 propellant per day, as needed by the architecture. To provide power to processing equipment inside Shackleton Crater, optimal locations are determined on the crater rim, from which several reflecting TransFormers (TFs) would redirect sunlight, achieving a combined period of illumination of approx. 99% of the year. A single 40-m diameter reflector could provide up to 1 MW solar power. Inflatable rigidizable tower support structures raise reflectors above ground for better solar exposure. There are trade-offs: e.g., two reflectors at ground level would provide the same combined total illumination as a single tower approx. 100-m tall. Such a TF based on a 100-m tower made with inflatable 2-m beams and 40-m diameter reflectors would be of similar dimensions as an MSL-class rover (approx. 1000 kg, 10 m(exp 3)). A TF-prospector rover combo could be designed and deployed in a Discovery-class mission searching for water. The TransFormers would be nodes of a Lunar Utilities Infrastructure that provides solar power year-round in the proximity of the pole, as well as local data transmission andintermittent direct to earth communications. This infrastructure would be instrumental infacilitating the development of a lunar economy.

fuel↗

NASA NTRS1978

Experimental investigation of outdoor propagation of finite-amplitude noise

The outdoor propagation of finite amplitude acoustic waves was investigated using a conventional electroacoustic transmitter which was mounted on the ground and pointed upward in order to avoid ground reflection effects. The propagation path was parallel to a radio tower 85 m tall, whose elevator carried the receiving microphone. The observations and conclusions are as follows: (1) At the higher source levels nonlinear propagation distortion caused a strong generation of high frequency noise over the propagation path. For example, at 70 m for a frequency 2-3 octaves above the source noise band, the measured noise was up to 30 dB higher than the linear theory prediction. (2) The generation occurred in both the nearfield and the farfield of the transmitter. (3) At no measurement point was small-signal behavior established for the high requency noise. Calculations support the contention that the nonlinearity generated high frequency noise never becomes small-signal in its behavior, regardless of distance. (4) When measured spectra are scaled in frequency and level to make them comparable with spectra of actual jet noise, they are found to be well within the jet noise range. It is therefore entirely possible that nonlinear distortion affects jet noise.

Webster, D. A.↗

NASA NTRS1981

The measurement of the ground wind structure at Wallops Island

The mean and turbulence characteristics of the surface wind measured near the Atlantic coast were measured. The experimental data were acquired from a 76 meter tall instrumented micrometeorological tower. Mean wind and turbulence measurements were made with two types of instrumentation consisting of cup vane and temperature probes, primarily used for mean profile measurements of velocity and temperature respectively. The second system, a hot film and thermocouple system, was used for measurement of turbulence variances and covariances and spectra. The cup vane system was used to acquire data from all wind directions, while the hot film system was primarily used for turbulence measurements from the two prevailing wind directions, south and northwest. The micrometeorological tower is a self standing nonguyed tower with five working platforms at 15.2m (50 ft.) intervals, with cup vane and aspirated temperature probes mounted at each platform.

Tielman, H. W.↗

NASA NTRSDate not supplied

Computational and Physics-Based Modeling for the Development of in-Space Welding Technology

Welding will be an enabling technology for in-space assembly and manufacturing (ISAM) and in-space repair operations in support of the growing Space Economy. Prospective use cases of welding include metal repair on long-duration lunar surface missions and assembly of large structures that exceed dimensions of the currently available launch vehicle envelopes such as space arrays, tall lunar transmission towers, or even large transit vehicles powered by nuclear propulsion. There is a brief history of beam welding for in-space use. Soviet and NASA astronauts performed electron beam welds (EBW) in space in the late-1960s through mid-1980s and several parabolic flights of laser beam welding (LBW) were undertaken in the USA and Canada in the early-1990s. Work has since stagnated until the recent boom of the in-space economy has demonstrated need for continued development of EBW and LBW processes, which are desirable for their compactness, low mass, low power consumption, and high wall plug efficiency. No space-based manufacturing laboratory capable of demonstrating, developing, and applying welding processes exists, and costs are high to develop and fly individual space-based trials. This drives the current approach to develop welding technology with computational and physics-based models in tandem with earth-based experiments. Several approaches are taken to complement and drive the selection of instrumentation for planned parabolic and suborbital flights. First, a thermal model of Skylab EBW experiments is established and compared to empirical data. Next, the model is used to show variation between Earth-based and in-space weld structure and properties through exploration of key variables that define the Low earth orbit and lunar surface space environments, namely temperature (40 – 400 K), pressure (10-10 to 104 Pa), and gravity (10-6 g to 1 g). Finally, physical processes associated with heat and mass transport during welding are evaluated through several case studies across the above variable ranges demonstrating need for further research.

in-space welding↗