Search NASA⌕ Search

SEARCH · Search NASA

Results for “temperature coefficients”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Ultra-wide bandgap β-Ga 2 O 3 films: Optical, phonon, and temperature response properties

Optical and phonon interactions of Ga 2 O 3 thin films with nanocrystalline morphology were studied at extreme temperatures. The films were grown using a sputtering technique and analyzed via temperature response transmission, Raman scattering, and high-resolution deep-UV photoluminescence (PL). Raman modes indicated that the structure corresponds to the β-phase. The optical-gap at the range of 77–620 K exhibited a redshift of ~200 meV, with a temperature coefficient of ~0.4 meV/K. The optical-gap at room-temperature is 4.85 eV. The electron–phonon interaction model at that temperature range pointed to a low energy phonon, ~31 meV, that is involved in the thermal properties of the optical-gap. Detailed Urbach energy analysis indicated that defects are the dominant mechanism controlling the band-edge characteristics even at an elevated temperature regime where phonon dominance is usually expected. Defects are attributed to the disordered forms of graphite that were detected via Raman scattering and to the granular morphology of the film. A deep-UV laser with an above bandgap exaction line of 5.1 eV was employed to map the PL of the films. The highly resolved spectra, even at room-temperature, show a strong emission of ~3.56 eV attributed to self-trapped holes (STHs). The STH is discussed and modeled in terms of the self-trapped exciton. Moreover, a very distinct but low-intensity emission was found at 4.85 eV that agrees with the value of the optical-gap and is attributed to bandgap recombination. The intensity ratio between the STH and that of the bandgap was found to be 6:1.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A comparative reactivity study of 1-alkene fuels from ethylene to 1-heptene

In this work, a comparative reactivity study of 1-alkene fuels from ethylene to 1-heptene has been performed using ignition delay time (IDT) measurements from both a high-pressure shock tube and a rapid compression machine, at an equivalence ratio of 1.0 in ‘air’, at a pressure of 30 atm in the temperature range of 600–1300 K. At low temperatures (< 950 K), the results show that 1-alkenes with longer carbon chains show higher fuel reactivity, with 1-pentene being the first fuel to show negative temperature coefficient (NTC) behavior followed by 1-hexene and 1-heptene. At high temperatures (> 950 K), the experimental results show that all of the fuels except propene show very similar fuel reactivity, with the IDTs of propene being approximately four times longer than for all of the other 1-alkenes. To analyze the experimental results, a chemistry mechanism has been developed using consistent rate constants for these alkenes. At 650 K, flux analyses show that hydroxyl radicals add to the double bond, followed by addition to molecular oxygen producing hydroxy-alkylperoxy radicals, which can proceed via the Waddington mechanism or alternate internal H-atom isomerizations in chain branching similar to those for alkanes. We have found that the major chain propagation reaction pathways that compete with chain branching pathyways mainly produce hydroxyl rather than hydroperoxyl radicals, which explains the less pronounced NTC behavior for larger 1-alkenes compared to their corresponding alkanes. At 1200 K, flux analyses show that the accumulation of hydroperoxyl radicals is important for the auto-ignition of 1-alkenes from propene to 1-heptene. The rate of production of hydroperoxyl radicals for 1-alkenes from 1-butene to 1-heptene is higher than that for propene, which is due to the longer carbon chain facilitating hydroperoxyl radical formation via more efficient reaction pathways. This is the major reason that propene presents lower fuel reactivity than the other 1-alkenes at high temperatures.

1-Alkene↗
DOE OSTI2023

Studies of Low and Intermediate Temperature Oxidation of Propane up to 100 Atm in a Supercritical-Pressure Jet-Stirred Reactor

Here, the low and intermediate temperature oxidation of propane has been investigated by using a novel supercritical pressure jet stirred reactor (SP-JSR) with and without 20% CO 2 additions at fuel lean and rich conditions at 10 and 100 atm and 500–1000 K. The mole fractions of C 3 H 8 , O 2 , CO, CO 2 , CH 2 O, C 2 H 4 , CH 3 CHO, and C 3 H 6 were quantified by using a micro-gas chromatograph (µ-GC). The experiment showed that different from that of 10 atm, at 100 atm only a weak negative temperature coefficient (NTC) behavior was observed because of the significant shift of the intermediate temperature HO 2 chemistry to lower temperature. In addition, at 100 atm, existing models in literatures could successfully capture the onset temperatures of the low and intermediate chemistry, while under-predict the fuel oxidation quantitatively and fail to capture the NTC behavior between 650 and 780 K at both fuel lean and rich conditions. Similar discrepancy was observed in studies of n-butane and dimethyl ether (DME) oxidations in literatures, implying that there existed large uncertainties in hierarchy model development of fuels with low temperature chemistries at extremely high pressures. Reaction pathways and sensitivity analyses showed that RO 2 competing reactions through (P1) RO 2 = QOOH, (P2) RO 2 = C 3 H 6 + HO 2 , (P3) RO 2 + CH 2 O/HO 2 = RO 2 H + HCO / O 2 dominated the low and intermediate temperature chemistries, followed by HO 2 / H 2 O 2 chemistry at 100 atm, which differed from the dominant pathway through QOOH consumption reactions at lower pressures. Especially, P3 is a new pathway of RO 2 consumption at high pressures, which was not observed in importance at low pressures. Special attention should be paid to the accurate computations of n-C 3 H 7 O 2 / i-C 3 H 7 O 2 + CH 2 O and n-C 3 H 7 O 2 / i-C 3 H 7 O 2 + in the P3 pathway and n-C 3 H 7 O 2 / i-C 3 H 7 O 2 decomposition reactions in the P2 pathway at high pressures.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Microstructure refinement of hot deformed Dy-free NdFeB magnets through a novel cold sintering approach by pressure-assisted spark plasma sintering

Anisotropic fine-grained Dy-free NdFeB high-performance magnets were produced using a novel cold sintering approach by pressure-assisted spark plasma sintering (SPS). The NdFeB nanocrystalline ribbon powders were subjected to cold sintering below 450 °C using pressure-assisted SPS, followed by hot deformation at 710 °C and 810 °C via SPS. Results indicate that cold sintering below 450 °C effectively restricts grain growth in the NdFeB magnets, yielding sub-100 nm scale grains across both fine-grained regions and most coarse-grained regions. The refined grain structure achieved through cold sintering allows for a lower hot deformation temperature as compared with the magnet by conventional sintering, as finer grains allow easier deformation and grain sliding/rotation. This process produces a highly fine-grained and anisotropic microstructure to achieve high magnetic performance (i.e., high intrinsic coercivity, remanence, and maximum energy product) in the magnets. The cold sintering (at 350 °C) and lower hot deformation temperatures required (e.g., 710 °C) help control grain coarsening and limit grain size that is commensurate with the size of a single magnetic domain of the Nd 2 Fe 14 B magnetic matrix phase, resulting in high intrinsic coercivity (H ci =11.4 kOe). Furthermore, the reduced hot deformation temperature mitigates the formation of coarse grain bands, leading to improved magnetic properties, specifically an increased remanence (B r = 14.3 kGs) and a high maximum energy product ((BH) max = 48 MGOe). In conclusion, cold sintered hot deformed NdFeB magnet also shows good thermal stability with reversible temperature coefficient α(B r )= -0.097 %/K and α(H ci )= -0.616 %/K at elevated temperatures up to 400 K.

Cold Sintering↗
DOE OSTI2023

Origin of magnetic ordering in half-Heusler RuMnGa

The half-Heusler alloy RuMnGa having valence electron count (VEC) 18 has recently been theoretically proposed to exhibit compensated ferrimagnetic (CFiM) character instead of the expected nonmagnetic ground state. On the other hand, a preliminary experimental study proposed ferromagnetic (FM) ordering. As no half-Heusler system with VEC 18 is known to exhibit magnetic ordering, we have investigated the details of crystal structure and magnetic properties of RuMnGa using a combination of experimental tools, viz., x-ray and neutron diffraction techniques, dc and ac susceptibility, isothermal magnetization, heat capacity, resistivity and neutron depolarisation measurements. Rietveld refinements of x-ray and neutron diffraction data suggest single phase nature of the compound with elemental composition RuMn 0.86 Ga 1.14 . We have shown that the system exhibits FM-type ordering owing to the inherent presence of this minor off-stoichiometry, showing very low magnetic moment. Further, the system also exhibits reentrant canonical spin-glass behavior, which is rarely observed in half-Heusler alloys. The temperature coefficient of resistivity changes its sign from negative to positive and further to negative as the temperature decreases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Fuel molecular structure effect on autoignition of highly branched iso-alkanes at low-to-intermediate temperatures: Iso-octane versus iso-dodecane

Highly branched iso-alkanes are an important class of hydrocarbons found in conventional petroleum-derived and alternative renewable fuels used for combustion applications. Recognizing that chemical kinetics for most of these iso-alkanes, especially at low-to-intermediate temperatures, has not been well studied, an experimental and modeling investigation of two selected iso-alkanes, iso-octane (2,2,4-trimethylpentane, iC8) and iso-dodecane (2,2,4,6,6-pentamethylheptane, iC12), is conducted to understand the fuel molecular structure effect on their autoignition characteristics. Using a rapid compression machine (RCM), the ignition responses of iC8 and iC12 at varying pressures, temperatures, and equivalence ratios are characterized and compared. The newly-acquired experimental ignition delay times have been compared with the literature RCM and shock tube data, demonstrating the complementary nature of the current dataset. Further comparison of the experimental pressure traces and ignition delay times illustrates the reactivity crossover between iC8 and iC12. Namely, there exists a temperature window in the negative temperature coefficient regime within which iC12 is less reactive than iC8, but iC12 becomes more reactive outside this temperature window. Furthermore, a chemical kinetic model of iso-alkanes including both iC8 and iC12 is developed. Simulated results using this model are then compared to the experimental data obtained in this study and available in the literature, showing its ability to predict the experimental trends. Chemical kinetic analyses have also been conducted to identify the important reaction pathways controlling autoignition at varying conditions, and to elucidate the underlying mechanism leading to different reactivity trends between iC8 and iC12.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enhanced copper–carbon nanotube hybrid conductors with titanium adhesion layer

Cu–carbon nanotube (CNT) hybrids combine the advantages of the high electrical conductivity of Cu with the low temperature coefficient of resistance for CNTs, but require enhanced interfacing to improve the electrical performance when exposed to elevated temperatures. In this work, Ti and Ni were investigated as adhesion metals by thermally evaporating 10 nm layers onto a CNT conductor. SEM analysis shows Ni deposits as discrete nanoscale crystallites which coalesce after annealing to 400 °C in H 2 /Ar. Ti deposits uniformly along the CNT surface and is stable over such temperatures. A 100 nm deposition of Cu is shown to delaminate from the CNTs after annealing, and the resistance per length (R/L) increases by 40%. The Cu–Ni–CNT exhibits a 125% increase, while the Cu–Ti–CNT achieves a 12% decrease in R/L, for similar annealing conditions. Thus, Ti emerges as an effective adhesion metal, warranting its use in metal–CNT wire technologies for elevated temperature operation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Transient Modeling and Simulation of a Generic Stable Salt Reactor

A SAM system-level model of a generic stable salt reactor has been developed to investigate thermal-hydraulic behavior and safety performance under steady and transient conditions. The model integrates information generated from a reactor physics analysis using PROTEUS and PERSENT, and a computation fluid dynamics (CFD) analysis using STAR-CCM+. A loose, iterative coupling scheme between PROTEUS and SAM is implemented to calculate the equilibrium power and temperature distributions in the steady-state critical core condition. The converged steady-state model is then used in PERSENT to calculate the four reactivity feedback temperature coefficients (Doppler, fuel density, coolant density, and core radial expansion) and kinetic parameters that are needed in SAM to model the temperature feedback effects in transient simulations. Within the fully enclosed liquid fuel pins, natural convection is the dominant heat transfer mechanism. The STAR-CCM+ model of the fuel pin considers conjugate heat transfer from the liquid fuel salt to the pin cladding and external reactor coolant. The CFD results of the axial and radial temperature profiles are used to empirically determine an effective fuel salt thermal conductivity in the SAM fuel pin model so that the temperatures predicted by the SAM model match as closely as possible the CFD results. In the central region of the fuel pin, the effective thermal conductivity is as high as similar to 60 times the physical fuel salt thermal conductivity. The whole-plant SAM model is then used to simulate an unprotected station blackout transient. The results of this simulation showed that the large negative fuel axial expansion reactivity feedback reduces fission power to similar to 2.4% nominal power. The core is cooled by natural circulation, which removes heat in the core to the emergency heat removal system, and ultimately, to the ambient. However, peak fuel salt and cladding temperatures can potentially reach as high as 1500 K, albeit briefly, if the shutdown mechanism fails to operate.

stable salt reactor; transient simulations; system↗
DOE OSTI2023

1.2-kV Vertical GaN PIN Rectifier With Ion-Implanted Floating Guard Rings

Here, this work reports on the fabrication and properties of a homojunction gallium nitride (GaN) p-i-n (PIN) rectifier fabricated on a free-standing GaN substrate. Uniform device performance is achieved with breakdown voltage (BV) >1.2 kV and low ON-resistance × area ( R ON A ). The statistics of the BV measurements show 58.5% of devices achieve BV >1.3 kV, and 71.1% of devices achieve BV >1.2 kV, as attributed to high quality and control in both epitaxial growth and device process. At room temperature, R ON A is 0.23 mΩ∙ cm 2 at a current density ( J ) of 6.9 kA/cm2. The corresponding Baliga’s figure of merit is >5.97 GW/cm 2 . Temperature-dependent reverse I – V measurements were performed and show a positive temperature coefficient of 0.42 V/K, indicating the avalanche capability of reverse breakdown. Further analysis with the Poole-Frenkel model on the temperature-dependent measurement suggested that a trap-assisted tunneling process contributed to the reverse leakage current. Floating guard rings (FGRs) formed by nitrogen implantation serve as an effective edge termination technique in these GaN PIN rectifiers, resulting in uniform performance in both forward and reverse bias.

42 ENGINEERING↗
DOE OSTI2022

Methanol oxidation up to 100 atm in a supercritical pressure jet-stirred reactor

Methanol (CH 3 OH) has attracted considerable attention as a renewable fuel or fuel additive with low greenhouse gas emissions. Methanol oxidation was studied using a recently developed supercritical pressure jet-stirred reactor (SP-JSR) at pressures of 10 and 100 atm, at temperatures from 550 to 950 K, and at equivalence ratios of 0.1, 1.0, and 9.0 in experiments and simulations. Here, the experimental results show that the onset temperature of CH 3 OH oxidation at 100 atm is around 700 K, which is more than 100 K lower than the onset at 10 atm and this trend cannot be predicted by the existing kinetics models. Furthermore, a negative temperature coefficient (NTC) behavior was clearly observed at 100 atm at fuel rich conditions for methanol for the first time. To understand the observed temperature shift in the reactivity and the NTC effect, we updated some key elementary reaction rates of relevance to high pressure CH 3 OH oxidation from the literature and added some new low-temperature reaction pathways such as CH 2 O + HO 2 = HOCH 2 O 2 (RO 2 ), RO 2 + RO 2 = HOCH 2 O (RO) + HOCH 2 O (RO) + O 2 , and CH 3 OH + RO 2 = CH 2 OH + HOCH 2 O 2 H (ROOH). Although the model with these updates improves the prediction somewhat for the experimental data at 100 atm and reproduces well high-temperature ignition delay times and laminar flame speed data in the literature, discrepancies still exist for some aspects of the 100 atm low-temperature oxidation data. In addition, it was found that the pressure-dependent HO 2 chemistry shifts to lower temperature as the pressure increases such that the NTC effect at fuel-lean conditions is suppressed. Therefore, as shown in the experiments, the NTC phenomenon was only observed at the fuel-rich condition where fuel radicals are abundant and the HO 2 chemistry at high pressure is weakened by the lack of oxygen resulting in comparatively little HO 2 formation.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

A High-Throughput MEMS-Based Differential Scanning Calorimeter for Direct Thermal Characterization of Antibodies

Calorimeters, which can be used for rapid thermal characterization of biomolecules, are getting intense attention in drug development. This paper presents a novel MEMS-based differential scanning calorimeter (DSC) for direct thermal characterization of protein samples. The DSC consisted of a pair of temperature sensors made by vanadium oxide (VOx) film with a temperature coefficient of resistivity of –0.025/K at 300 K, a microfluidic device with high thermal insulation (2.8 K/mW), and a Peltier heater for linear temperature scanning. The DSC exhibited high sensitivity (6.1 µV/µW), low noise (0.4 µW), high scanning rate (45 K/min), and low sample consumption volume (0.63 µL). The MEMS DSC was verified by measuring the temperature-induced denaturation of lysozyme at different pH, and then used to study the thermal stability of a monoclonal antibody (mAb), an antigen-binding fragment (Fab), and a dual variable domain immunoglobulin (DVD-Ig) at pH = 6. The results showed that lysozyme is a stable protein in the pH range of 4.0–8.0. The protein stability study revealed that the transition temperatures of the intact Fab fragment, mAb, and DVD proteins were comparable with conformational stability results obtained using conventional commercial DSC. These studies demonstrated that the MEMS DSC is an effective tool for directly understanding the thermal stability of antibodies in a high-throughput and low-cost manner compared to conventional calorimeters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Thermal stability of antiferroelectric-like Al:HfO 2 thin films with TiN or Pt electrodes

HfO 2 -based antiferroelectric-like thin films are increasingly being considered for commercial devices. However, even with initial promise, the temperature sensitivity of electrical properties such as loss tangent and leakage current remains unreported. 50 nm thick, 4 at. % Al-doped HfO 2 thin films were synthesized via atomic layer deposition with both top and bottom electrodes being TiN or Pt. A study of their capacitance vs temperature showed that the Pt/Al:HfO 2 /Pt had a relative dielectric permittivity of 23.30 ± 0.06 at room temperature with a temperature coefficient of capacitance (TCC) of 78 ± 86 ppm/°C, while the TiN/Al:HfO 2 /TiN had a relative dielectric permittivity of 32.28 ± 0.14 at room temperature with a TCC of 322 ± 41 ppm/°C. The capacitance of both devices varied less than 6% over 1 to 1000 kHz from –125 to 125 °C. Both capacitors maintained loss tangents under 0.03 and leakage current densities of 10 –9 –10 –7 A/cm 2 between –125 and 125 °C. The TiN/Al:HfO 2 /TiN capacitor maintained an energy storage density (ESD) of 18.17 ± 0.79 J/cm 3 at an efficiency of 51.79% ± 2.75% over the –125 to 125 °C range. The Pt/Al:HfO 2 /Pt capacitor also maintained a stable ESD of 9.83 ± 0.26 J/cm 3 with an efficiency of 62.87% ± 3.00% over the same temperature range. Finally, such low losses in both capacitors along with their thermal stability make antiferroelectric-like, Al-doped HfO 2 thin films a promising material for temperature-stable microelectronics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Startup Test Plan and Predictions for Highly Enriched Uranium to Low-Enriched Uranium Fuel Conversion at the University of Missouri Research Reactor

Nonpower reactors licensed by the U.S. Nuclear Regulatory Commission require a startup test plan as part of any facility modification to verify operability prior to resumption of operations. In order to support conversion of the University of Missouri Research Reactor from the use of highly enriched uranium to low-enriched uranium (LEU) fuel, a startup test plan has been devised to measure certain reactor physics parameters for the initial all-fresh LEU core licensing documentation that will be submitted. These parameters include the approach to critical, primary coolant void coefficient of reactivity, flux trap void coefficient of reactivity, determination of flux trap sample reactivity worth, radial and axial thermal neutron flux mapping, control blade worth calibration, primary and pool coolant temperature coefficient of reactivity, and flux mapping of experimental positions. Here, predictions for these parameters made using the Monte Carlo N-Particle Version 5 (MCNP5) radiation transport code are reported. These predictions will support the startup tests by providing a baseline set of expectations and additional insight into the performance of the LEU core.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Distributed Fiber Sensors With High Spatial Resolution in Extreme Radiation Environments in Nuclear Reactor Cores

This paper is a comprehensive experimental report on the neutron radiation effects of distributed optical fiber sensors with enhanced Rayleigh scattering profiles in an in-pile environment. Femtosecond laser direct writing was used to inscribe Type-II modifications in standard telecom fibers and radiation-hardened fibers with fluorine-doped cores. Rayleigh backscattering signals were enhanced for continuous 1.5 m. In-pile lead-out sensors tests were carried out at the MIT Research Reactor for two months, which was operated at a nominal power of 5.7 MW with fast neutron (>0.1 MeV) flux of 1.29 × 1014 n/cm2/s and an in-core temperature of up to 560°C. Using the Optical Frequency Domain Reflectometry technique, the backscattering profiles of fiber sensors were interrogated with a 3-cm spatial resolution to monitor the temperature profile of the reactor. Results show that laser inscribed Type-II modifications in the form of nanogratings are highly stable against extreme temperature and ionizing radiation. Both standard telecom fibers and radiation-hardened fibers with laser-enhanced Rayleigh profiles can continuously perform distributed temperature measurements over the entire duration of the in-pile testing. Temperature coefficients of sensors and spectral shift quality were studied as functions of total radiation fluence. To the best of our knowledge, we present for the first time, the temperature profile of an operating nuclear reactor core with 3-cm spatial resolution, enabled by distributed fiber sensors with laser-enhanced Rayleigh scattering profiles. The high spatial resolution measurements can provide valuable data for the design and validation of digital twin and virtual reality of nuclear energy systems.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Operando Temperature Measurements of Photovoltaic Laser Power Converter Devices Under Continuous High-Intensity Illumination

Photovoltaic devices that operate under extremely high irradiances, such as laser power converters (LPCs), may also operate at elevated temperatures, even under active cooling, as the result of large temperature gradients. We demonstrate the operation of GaAs LPC devices under orders of magnitude of irradiances up to 150 W/cm 2 in a monochromatic laser simulator with an active cooling stage. The steady-state open-circuit voltage (V OC ) as a function of irradiance is known to droop at high irradiance as the result of junction heating, but the junction temperature can be difficult to measure by conventional methods. Fast, transient V OC measurements under these extreme operating conditions are used here to determine the junction temperature. Empirical V OC temperature coefficients of the devices at each irradiance of interest are determined and used as an integral part of this technique. We show that the thermal design of different LPC devices strongly affects the operating temperature of the junctions. Knowledge of the operating temperature can be a strong tool for understanding the nature of loss mechanisms and improving the design for the operation of photovoltaic LPCs at high irradiances. Furthermore, this technique can be used for laboratory devices during initial design as well as to characterize mass-produced and packaged devices for quality control.

14 SOLAR ENERGY↗
DOE OSTI2025

Optimizing energy yield of monolithic perovskite/silicon tandem solar cells in real-world Conditions: The impact of luminescent coupling

Efficient light management is key to maximizing power conversion efficiency (PCE) in monolithic perovskite/silicon tandem solar cells. Achieving peak efficiency requires closely matched current generation in all junctions, especially in integrated configurations. However, real-world conditions vary significantly due to factors such as sunlight spectrum, diffuse-to-direct sunlight ratio, angular distribution of light, subcell temperature coefficients, and ground reflection. This study introduces a comprehensive optical and device simulation to optimize perovskite/silicon tandem cells, considering experimental luminescent coupling (LC) efficiency and its dependence on working conditions, alongside variations in radiative recombination, effect of temperature on absorptivity spectra, and cloud cover. Our results show potential energy yield improvements of up to 1.4 % with LC, based on current perovskite radiative recombination records, and up to 4 % with direct bandgap materials. Although radiative recombination's dependence on excitation intensity reduces output power and requires thicker absorbers, LC compensates for these losses. LC also lowers the optimized bandgap for the perovskite top cell from 1.72 eV to 1.64–1.68 eV, or even lower in regions with redshifted irradiance. Additionally, optimization revealed that thinner silicon bottom cells require a higher perovskite top cell bandgap, impacting the balance between fabrication cost and cell stability.

14 SOLAR ENERGY↗
DOE OSTI2023

Multi-parameter distributed fiber optic sensing using double-Brillouin peak fiber in Brillouin optical time domain analysis

In this paper, we demonstrate a multi-parameter fiber sensing system based on stimulated Brillouin scattering in a double-Brillouin peak specialty fiber with enhanced Brillouin gain response. The amplitude level of the second Brillouin gain peak, which originated from the higher-order acoustic modes, has been improved with an approximately similar amplitude level to the first Brillouin gain peak from the fundamental acoustic mode. Compared to other multi-Brillouin peak fibers presented in the literature, the proposed fiber significantly reduces the measured Brillouin frequency shift error, thus improving strain and temperature accuracies. By utilizing the sensitivity values of the strain and temperature associated with each Brillouin gain spectrum (BGS) peak, a successful discriminative measurement of strain and temperature is performed with an accuracy of ±13 μɛ, and ±0.5 °C, respectively. The proposed double-Brillouin peak fiber appears to be a possible alternative to other multi-BGS peak fibers, for instance, large effective area fiber and dispersion compensating fibers, which are inherently accompanied by large measurement errors due to the weak Brillouin gain values originating from the higher-order acoustic modes. The demonstrated results show different strain and temperature coefficients of 47 kHz/µɛ, 1.15 MHz/°C for peak 1 and 51 kHz/µɛ, 1.37 MHz/°C for peak 2. Moreover, the enhanced BGS peak gains having nearly the same amplitude levels enable the discriminative measurement of strain and temperature. Such fibers in Brillouin interrogation eliminate the need for complex monitoring setups and reduce measurement errors. We recommend that for long-distance natural gas pipeline monitoring, where discriminative strain and temperature measurement is crucial, the proposed double-Brillouin peak fiber can be highly beneficial.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

SCALE 6.3 Validation: Reactor Physics

This study was performed to validate the SCALE/Polaris v6.3.0–PARCS v3.4.2 code procedure with the ENDF/B-VII.1 AMPX 56-group library for light-water reactor analysis by comparing the simulated results with the measured data for critical experiments and operating light-water reactors. Uncertainties of the SCALE/Polaris–PARCS code procedure for light-water reactor physics analysis were evaluated in the validation for key nuclear parameters such as reactivity, control bank work, temperature coefficients, and pin and assembly power peaking factors. In addition, the SCALE/TRITON v6.3.1 procedure with the ENDF/B-VII.1 and VIII.0 252-group and continuous-energy cross sections was validated for non-lightwater reactors including the HTR-10 reactor, the High-Temperature Test Reactor, the Molten Salt Reactor Experiment, and the Experimental Breeder Reactor II.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗