Search NASA⌕ Search

SEARCH · Search NASA

Results for “thermoplastic reinforcement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Hygrothermal Aging and Thermomechanical Characterization of As-Manufactured Tidal Turbine Blade Composites

This study investigates the hygrothermal aging behavior and thermomechanical properties of as-manufactured glass fiber-reinforced epoxy and thermoplastic composite tidal turbine blades. The blades were previously deployed in a marine environment and subsequently analyzed through a comprehensive suite of material characterization techniques, including hygrothermal aging, dynamic mechanical analysis (DMA), tensile testing and X-ray computed tomography (XCT). Hygrothermal aging experiments revealed that while thermoplastic composites exhibited lower overall water absorption (0.78% vs. 0.47%), they had significantly higher diffusion coefficients than epoxy (2.1 vs. 12.1 × 10 −13 m 2 s −1 ), suggesting faster saturation in operational environments. DMA results demonstrated that water ingress caused plasticization in epoxy matrices, reducing the glass transition temperature and increasing damping (112 °C to 104 °C), while thermoplastic composites showed more stable thermal behavior (87 °C glass transition temperature). Tensile testing revealed substantial reductions in ultimate strength (>40%) for both materials after prolonged water exposure, with minimal change in elastic modulus, highlighting the role of matrix degradation over fiber reinforcement. XCT image analysis showed that both composites were manufactured with high quality: no large voids or cracks were present, and the degree of misalignment was low. These findings inform future marine renewable energy composite designs by emphasizing the critical influence of moisture on long-term structural integrity and the need for optimized material systems in harsh marine environments. This work provides a rare real-world comparison of epoxy and recyclable thermoplastic tidal turbine blades, showing how laboratory aging tests and advanced imaging reveal the influence of material and manufacturing choices on long-term marine durability.

16 TIDAL AND WAVE POWER↗
DOE OSTI2026

Low-Cost Highly Recyclable Structural Composites Utilizing Vitrimers and Natural Fibers (Basalt) Manufactured via a Novel Pultrusion Method for High-Volume Applications

The project’s overall goal is to explore and demonstrate as proof-of-concept that a highly recyclable and repairable composite material system, that is reinforced with natural fibers, can be used to produce lightweight structural components using a low-cost manufacturing process for high-volume automotive applications. More specifically, the project’s objectives will focus on vitrimer resins (which are a hybrid polymeric system of thermoplastics and thermosets) reinforced with basalt fibers and manufactured using pultrusion technologies. Pultrusion, as a method, is well-known to be one of the lowest-cost manufacturing processes for high-volume applications. However, to date, the validity and viability of such attractive objectives have not been demonstrated in support of the automotive industry.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A review of the fabrication methods and mechanical behavior of continuous thermoplastic polymer fiber–thermoplastic polymer matrix composites

Abstract Thermoplastic polymer fiber–thermoplastic polymer matrix composites (PPCs or PRFPs), often recognized as self‐reinforced or single polymer composites, are potential candidates for future advanced polymer composites because of various advantages ( e.g., recyclability, formability, low‐cost, ultra‐lightweight, environmental friendliness, etc.). The manufacturability and mechanical behavior of these composites compared to conventional carbon‐/glass‐/aramid‐fiber‐reinforced polymers is of great interest to the composites community, but there are a limited number of studies in this area. To this end, this paper reviewed fabrication methods with different processing parameters and mechanical behavior of uni‐/multi‐directional thermoplastic PPCs featuring continuous thermoplastic polymer fibers from limited data in the literature. It was shown that most specific behaviors (normalized by density) of these materials in various loading conditions (e.g., quasi‐static tension/shear/flexure, tension‐tension fatigue, and out‐of‐plane impacting, etc.) are comparable to or better than glass‐/aramid‐fiber‐reinforced polymers. Particularly, the specific ductility in the foregoing conditions outperforms all the carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Thermoplastic PPCs with remarkable performance can be achieved through several uncomplicated methods (e.g., film stacking, hot compaction, powder and solution impregnations, matrix infusion and injection molding, additive manufacturing, etc.), which have some similarities to the methods used for carbon‐/glass‐/aramid‐fiber‐reinforced polymers. Moreover, several opportunities and challenging problems of thermoplastic PPCs were summarized at the end of this review paper. Efficient solutions may require countless efforts in the composites community to further strengthen the performance and understanding of thermoplastic PPCs for wide applications in various engineering fields in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dynamic behavior of reversible oxygen migration in irradiated-annealed high temperature superconducting wires

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Post-process annealing of large-scale 3D printed polyphenylene sulfide composites

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hygrothermal aging and recycling effects on mechanical and thermal properties of recyclable thermoplastic glass fiber composites

Abstract Glass fiber‐reinforced polymer composites are widely used in marine applications, including renewable energy devices and submarines, due to their strength‐to‐weight ratios and corrosion resistance. As sustainability becomes more important, recyclable thermoplastic composites are gaining attention in marine energy applications. These materials face harsh conditions such as high chloride water, UV radiation, pressurization, and thermal cycling, which can affect their durability and recyclability. This study examines the impact of hygrothermal aging on the recyclability of an Elium glass fiber (GF) composite. Samples were mechanically ground for recycling, and mechanical and thermal properties were compared between aged and unaged samples. After seawater aging, the tensile strength and modulus of the unaged composite dropped by 25% and 13% respectively, due to water ingress along the fiber‐matrix interface. The recycled composite showed reduced flexural strength as the long fiber composite was converted into short fibers during the process. Differential scanning calorimetry (DSC) revealed no change in glass transition temperature after aging. Weight loss (25%) was attributed to the thermal stability of the glass fibers. Dynamic mechanical analysis (DMA) showed that the storage modulus increased with aging, and fracture analysis confirmed a mixed mode of failure for aged composites. Highlights Hygrothermal aging lowers mechanical performance of Elium® GF composites. Failure mechanism tends to be matrix cracking and interface bonding. Glass transition temperature is not reduced by hygrothermal aging. Fractured composite was successfully recycled via thermoforming. Flexural strength of the recycled composite is lower.

17 WIND ENERGY↗
DOE OSTI2025

Property optimized energy absorber for automotive bumpers utilizing multi-material and structural design strategies

This study proposes a novel design for automotive bumper using optimized lattice structures and multi-materials to balance low-speed collision and high-speed pedestrian impact performance. Different blends of 20 % carbon fiber-reinforced acrylonitrile butadiene styrene with thermoplastic polyurethane were used to tailor material properties. The energy absorber features lattice structures with customized mechanical responses, created by varying the incline angle θ from 0 to 180°. We conducted 576 finite element simulations on a half-scale model to optimize energy absorption and stiffness, leading to 66 optimized designs that met both low-speed and high-speed impact criteria. Two sub-scale optimized energy absorbers with different peak forces—both meeting low-speed impact requirements—were 3D printed and validated through drop-weight testing. The one with lower peak stress demonstrated a more compliant response, exhibiting approximately 90 % lower initial peak force and an increase in energy absorption of around 33 % (from 24 J to 32 J). Compared to the baseline triangular lattice, the optimized absorber increased energy absorption by 68 % from (19 J to 32 J) and reduced peak stress by 70 %. It also showed near-complete recovery with minimal fractures, making it suitable for repeated use. This design improves safety while offering a lightweight, durable, and cost-effective bumper system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Methane Pyrolysis for CO2-free H2 and Carbon Nanomaterials (Abstract)

We propose to continue to develop a new process for producing CO2-free hydrogen (H2) from inexpensive and domestically-abundant natural gas (NG), while simultaneously reducing H2’s net production cost to $1.0/kg through the sale of valuable crystalline solid carbon co-product. Producing clean hydrogen at this price is a DOE Hydrogen Energy Earthshot goal. Cost effective production of clean H2 is also of commercial relevance to project partners Southern California Gas Company (SoCalGas) and startup company C4-MCP, who aim to further develop, demonstrate at scale, and ultimately deploy the new process technology developed on this project in order to meet regulatory demands in the State of California. In the current project we have focused on i) understanding the catalyst science for thermocatalytic decomposition of methane (TCD), which resulted in the development of a patent pending bimetallic catalyst offering favorable activity, stability, and selectivity under industrially relevant process conditions, ii) developing a novel, patent pending process to enable the separation of produced carbon and catalyst, and re-synthesis of the catalyst using recycled materials, iii) performing limited characterization of the produced carbon materials, and iv) performing detailed process modeling in order to perform techno economic assessment. The additional scope proposed here will accelerate the commercial deployment of TCD for CO2-free H2 and valuable solid carbon nanotubes (CNT) co-product, by i) scaling up the production of CNT co-product using a scalable, fluidized bed reactor (25 g catalyst scale versus the 1 g catalyst scale demonstrated to-date), ii) producing at least 40 g of CNT product, produced via multiple cycles of TCD, carbon-catalyst separation, and catalyst re-synthesis, to enable the production of sufficient quantities of solid carbon so as to explore its market potential, iii) understanding the quality of the co-product CNTs, produced at larger scale, through advanced characterization, and iv) beginning to explore multiple promising high volume carbon product applications (thermoplastics, automotive composites, battery, and cement reinforcement applications).

08 HYDROGEN↗
DOE OSTI2024

Evaluation of Dissolvable Additively Manufactured Molds and Supports for Electroimpacts Innovative Additive Manufacturing Process

Electroimpact inc. has developed a new additive manufacturing process involving continuous fiber reinforcement along with high-strength thermoplastics. A unique part of this process includes using additive manufacturing to print a base geometry that is then used as a tool for continuous fiber placement. Ideally the tool should be disposable and cost effective. After printing the base tool, continuous fiber is printed on top of the tool using a secondary additive head on the same system to create the final printed part. After continuous fiber printing is completed, the tool is removed and disposed of to leave only the final desired structure. Materials used for the base tool have several requirements that must be met in order to complete this process. First, the material must be rigid and strong enough to support the loads from the secondary printing operation (continuous fiber printing). In addition, the material must be able to adhere to the secondary process material as well be capable of being removed such that the only remaining structure is continuous fiber composite. Using innovative soluble materials allows for parts to be produced through additive with molds that are produced as non-reusable one-off shapes and sizes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Devices and methods for additive manufacturing using flexible filaments

A method of fabricating (printing) parts utilizing flexible filaments includes anchoring a portion of a flexible filament to a substrate. A length of flexible filament is extended over the substrate while the flexible filament is in tension to thereby avoid buckling of the flexible filament. The flexible filament may comprise a thermoplastic material and fibers or other reinforcing materials whereby composite 3D parts can be fabricated.

Gardner, John M.↗
DOE OSTI2022

Rapid manufacturing of tailored preforms

A method for rapid manufacturing of three dimensional discontinuous fiber preforms is provided. The method includes the deposition of a polymeric material containing fibers on a surface to form a tailored charge for compression molding. The reinforced polymeric material may be a thermoplastic or a reactive polymer with viscosity low enough to allow flow through an orifice during deposition, yet high enough zero shear viscosity to retain the approximate shape of the deposited charge. The material can be deposited in a predetermined pattern to induce the desired mechanical properties through alignment of the fibers. This deposition can be performed in a single layer or in multiple layers. The alignment is achieved passively by shear alignment of the fibers or actively through fiber orientation control or mixing. The fibers can be of the desired material, length, and morphology, including short and long filaments.

Kunc, Vlastimil↗
DOE OSTI2025

Using low cost, bio-derived and recycled materials in advanced scalable small- and medium- wind turbine manufacturing

In partnership with Bergey Windpower, this project explored the use of recyclable and recycled materials in small- to medium-wind turbine blades (WTBs). A recyclable epoxy resin and infusible thermoplastic resin were investigated using identical fiber reinforcements and manufacturing practices used as Bergey, and the substitution of continuous virgin glass fiber (GF) layers with recycled nonwoven GF (rGF, NW) mats was trialed. The alternative resins both showed very promising performance in terms of static tensile and flexural behavior as well as thermal properties and fatigue behavior in comparison with that of the incumbent materials used at Bergey. The NW rGF materials, however, were found to be a poor substitute for the continuous GF materials for two primary reasons. Firstly, the NW mats took up significantly more resin than their continuous counterparts, which would increase both the weight and the cost of the WTBs. Additionally, an unexpected reaction occurred between the rGF and epoxy materials that resulted in a highly porous, foamed structure. The foaming phenomenon was not observed with the rGF NW and infusible thermoplastic material, but the resin uptake was still prohibitively high. Based on the results of this study, recyclable infusible resins could be viable candidate materials for Bergey in the future. The foaming reaction with the rGF NW mats could prove highly useful in other applications requiring structural foams and has been used to produce demonstrative sandwich panels.

17 WIND ENERGY↗
DOE OSTI2023

Carbon Fiber and Polymer Composites

Tooling is an integral part of composites manufacturing. Composite tools, also called ‘soft’ tools, are more easily constructed than ‘hard’ metal tools and, because they are made from materials similar to the manufactured composite part, they can be made in-house and have a good co-efficient of thermal expansion match. However, as the ‘soft’ designation suggests, they are more vulnerable to wear and typically find application in relatively low-volume production. Additive manufacturing of thermoplastics has proven to be a lucrative option that can help improve the tooling functionalities, as it offers more design flexibility. Owing to the inherent nature of additive manufacturing, the possibility of printing sensors within the tool material and at proximity to otherwise inaccessible areas of the tool become a reality. Continuous carbon fiber (CCF)-reinforced three-dimensional (3D) printing of engineering thermoplastics has proven to be a viable option to strengthen a part well beyond the ideal moduli of unmodified thermoplastic. Furthermore, adding nanotubes or graphene to the thermoplastic matrix will also improve both the thermal conductivity and interlaminar shear strength within the tool. Carbon nanotubes (CNTs) and carbon fibers (CFs) are microwave susceptors; exploiting the physics of Joule heating to increase the energy efficiency of tool hardening and cure rates is a core goal of this project. Because of the rapid volumetric heating enabled by the absorption of microwave or radio frequency energy and electromagnetic (EM) annealing presents an attractive opportunity to significantly reduce manufacturing cycle times while improving part performance.

Craps, Matthew G.↗
DOE OSTI2023

Low-Velocity Impact Performances of Healed Polymer Fiber Reinforced Plastics

Extending the lifecycle of traditional carbon or glass fiber-reinforced plastics is a complicated problem. The lack of sustainability limits the applications of the traditional composite materials in the vehicle industries where recycling and repurposing are critical issues. Alternatives for the low-stressed structural components are polymer fiber-reinforced plastics (PFRPs). In PFRPs, both the fibers and matrix are composed of thermoplastic polymers (e.g. polypropylene or polyethylene). They are lightweight, easy to manufacture, and cost-effective. Additionally, recycling and repurposing thermoplastic polymers are well understood. Therefore, the PFRPs have strong advantages compared to the traditional fiber-reinforced composites in low-stressed structural applications. In this study, we investigated the low-velocity impact (LVI) performances of the PFRPs and compared them with carbon fiber-reinforced plastics (CFRPs). A semi-spherical impactor was dropped to flat, square panels, and the absorbed impact energy was measured. The damage mechanisms were examined using a Xray µCT scan. The PFRPs outperformed the CFRPs in terms of perforation energy normalized by plate thickness and density. After the perforation, we healed the fractured plates by leveraging the recyclability of the thermoplastic polymers. The healing process of the panels was identical to the initial panel manufacturing process. No additional materials were added during the healing process. The healed PFRP panels were impacted again and substantially recovered energy absorption capability. We also conducted the repeated-impact test with several different impact energies. Unlike the CFRPs where the impact peak load decreased as the impacts repeated, the PFRPs showed an increasing trend. Such a unique mechanism was due to the strain-hardening behavior of the polymer fibers and matrix. As a result, the repeated-impact life of the PFRPs was significantly enhanced. These results are particularly interesting in the automotive or aerospace industries where repeated LVI is frequently observed.

Ko, Seunghyun↗
DOE OSTI2021

IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades

(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.

17 WIND ENERGY↗
DOE OSTI2023

Recyclable Cellulose Fiber Reinforced Vitrimer Composite

Vitrimer is an innovative class of polymeric materials which demonstrates traditional thermoset-like mechanical and chemical resilience while still being able to flow on demand like a traditional thermoplastic through covalently adaptive dynamic linkages. Herein, high-performance cellulose fiber reinforced vitrimer composites are developed using an epoxy-based vitrimer and natural cellulose paper. The reinforced vitrimer composite was fabricated by impregnating the porous structure of cellulose paper with two curable monomers, followed by in-situ polymerization of the monomers inside the fibrous scaffold. The introduction of hydroxyl group present on the cellulosic framework assisted in a faster topological rearrangement of the crosslinked matrix through transesterification exchange reaction, thus imparting various sought-after properties like shape recovery and recyclability via simple thermal reprocessing. Moreover, the reinforced vitrimer composite exhibits superior tensile properties as high as 90 MPa with 15-25 volume% vitrimer loading due to the interfacial adhesion via ester exchange reaction between the epoxy matrix and functionalities on the cellulosic fibers. Noteworthily, the key ingredients of the resulting composite (i.e., epoxy-based vitrimer and cellulose fibers) can be comfortably recycled without using aggressive chemical treatment, enabling composite to be easily recycled or disposed of at the end of service life and assist in reducing the subsequent manufacturing cost. This study would shed light on the development of a recyclable polymer composite with exceptional mechanical properties while simultaneously demonstrating self-healing and shape memory capabilities.

Rohewal, Sargun Singh↗
DOE OSTI2024

Improving the Recyclability of Polymer Composites With Cellulose Nanofibrils

Cellulose nanofibers (CNFs) have been widely studied for their reinforcing potential in high-performance composites. While there are numerous publications on CNF-reinforced composites in a variety of polymer matrices, few have considered the recyclability of such thermoplastic composites and whether the incorporation of CNFs deteriorates or improves their performance upon reprocessing. In this study, two thermoplastic resins, poly(lactic acid) (PLA), and glycol-modified polyethylene terephthalate (PETg), were prepared with CNF reinforcement and thermomechanically recycled to investigate the effect of CNF inclusion on the composite properties after reprocessing as well as their effect on the composites’ number of useful life cycles. Additionally, changes in mechanical, thermal, rheological, molecular, and microstructural properties of the composites and/or base resins were monitored as a function of cycle numbers. As is typical, the polymers’ molecular weight and mechanical performance deteriorated with continued processing. However, the addition of spray dried CNF was found to better maintain the mechanical performance of both polymers throughout multiple recycling steps as compared to neat samples. For example, the tensile strength of PETg with 20 wt% CNF after 6 processing cycles was found to exceed that of virgin neat PETg, and higher loadings of CNF were found to preserve a higher yield strength during multiple rounds of reprocessing compared to PETg composites with lower CNF loadings. Ultimately this study indicates that the addition of CNF to some thermoplastic materials can increase both their sustainability by offsetting the use of high-embodied energy resins and their circularity by enabling performance retention over more use cycles.

42 ENGINEERING↗
DOE OSTI2026

Performance assessment of 3D printed multi-material energy absorber for automotive bumper: pedestrian lower extremity protection

Designing an energy absorber for automotive bumpers involves balancing low-speed and high-speed impacts to ensure safety, reduce repair costs, and meet regulatory standards. Here, this study explores a novel design using multi-material 3D printing and structural optimization to fabricate a lightweight and cost-efficient energy absorber. The design effectively dissipates energy in low-speed collisions and minimizes force transmission in high-speed pedestrain impacts, helping to meet both safety and performance requirements. The energy absorber design combines 20% carbon fiber-reinforced acrylonitrile butadiene styrene (CF-ABS) and thermoplastic polyurethane (TPU) for optimal stiffness and flexibility. It uses 3D-printed lattice structures optimized through finite element simulations to help meet both low-speed and high-speed impact requirements. Full-scale energy absorbers were 3D-printed using optimized CF-ABS/TPU blends and tested under high-speed impact using the Flexible Pedestrian Legform Impactor (Flex-PLI). For fair comparison, a baseline bumper with a traditional triangular lattice structure, also 3D-printed from the same CF-ABS/TPU materials, was similarly tested. Interestingly, both the optimized and baseline 3D-printed energy absorbers showed nearly identical performance, successfully meeting injury limits. Their performances were also benchmarked against an injection-molded energy absorber. While both 3D-printed and injection-molded designs met injury limits, the 3D-printed absorber exhibited a higher tibia bending moment, indicating an opportunity for further optimization. A Techno-Economic Analysis compared the costs of producing energy absorbers using traditional manufacturing and 3D printing. The analysis highlighted that 3D printing offers cost benefits for low to medium production volumes, with the total cost per energy absorber at ∼ $\$$74, compared to traditional methods that become economical beyond 2000 units.

Additive manufacturing↗