Search NASA⌕ Search

SEARCH · Search NASA

Results for “thin membrane”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Power Systems Evaluated for Solar Electric Propulsion Vehicles

Solar electric propulsion (SEP) mission architectures are applicable to a wide range NASA missions including the robotic exploration of the outer planets in the next decade and the human exploration of Mars within the next 2 decades. SEP enables architectures that are very mass efficient with reasonable power levels (1-MW class) aerobrake and cryogenic upper-stage transportation technologies are utilized. In this architecture, the efficient SEP stage transfers the payload from low Earth orbit (LEO) High Energy Elliptical Parking Orbit (HEEPO) within a period of 6 to 12 months. highthrust, cryogenic upper stage and payload then separate from the SEP vehicle for injection to the planetary target, allowing for fast heliocentric trip times. This mission architecture offers a potential reduction in mass to LEO in comparison to alternative all-chemical nuclear propulsion schemes. Mass reductions may allow launch vehicle downsizing enable missions that would have been grounded because of cost constraints. The preceding figure illustrates a conceptual SEP stage design for a human Mars mission. Researchers at the NASA Glenn Research Center at Lewis Field designed conceptual SEP vehicle, conceived the mission architecture to use this vehicle, and analyzed the vehicle s performance. This SEP stage has a dry mass of 35 metric tons (MT), 40 MT of xenon propellant, and a photovoltaic array that spans 110 m, providing power to a cluster of eight 100-kW Hall thrusters. The stage can transfer an 80-MT payload and upper stage to the desired HEEPO. Preliminary packaging studies show this space-station-class SEP vehicle meets the proposed "Magnum" launch vehicle and volume requirements with considerable margin. An SEP vehicle for outer planetary missions, such as the Europa Mapper Mission, would be dramatically smaller than human Mars mission SEP stage. In this mission architecture, the SEP power system with the payload to provide spacecraft power throughout the mission. Several photovoltaic array design concepts were considered for the SEP vehicle power system for the human mission to Mars. These include a space station derivative, a SCARLET (Solar Concentrator Arrays with Refractive Linear Element Technology) derivative, and a hybrid inflatable-deployable thin polymer membrane array with thin-film solar cells (as shown in the concept illustration). This concept is based on a design developed for the Next Generation Space Telescope Sun shield. The array is divided into 16 independent electrical sections with 500-V, negative-grounded solar cell strings. The power system employs a channelized, 500-Vdc power management and distribution (PMAD) architecture with lithium ion batteries for energy storage for vehicle and payload secondary loads (the high-power Hall thrusters do not operate in eclipse periods). The 500-V PMAD voltage permits "direct-drive" thruster operation, greatly reducing the power processing unit size, complexity, and power loss. Similar power system architecture, designs, and technology are assumed for the Europa Mapper Mission SEP vehicle. The primary exceptions are that the photovoltaic array is assumed to consist of two rectangular wings and that the power system rating is 15 kW in Earth orbit and 200 W at Europa. To size the SEP vehicle power system, a dedicated Fortran code was developed to predict detailed power system performance, mass, and thermal control requirements. This code also modeled all the relevant Earth orbit environments; that is, the particulate radiation, plasma, meteoroids and debris, ultraviolet radiation, contamination, and thermal conditions. Analysis results for the Human Mars Mission SEP vehicle show a power system mass of 9-MT and photovoltaic array area of 5800-square meters for the thin-membrane design concept with CuInS2 thin-film cells. Power processing unit input power for a thin-membrane array design with three-junction, amorphous SiGe solar cells is shown in the graph. Power falls off rapidly inhe first weeks of the mission because of light-induced (Staebler-Wronksi) solar cell losses. During the next 200 days, power decreases steadily as the SEP stage spirals through the proton belts and sustains the bulk of the mission radiation damage. Once the vehicle apogee is above approximately four Earth radii, little additional degradation is incurred. From 400 to 800 days, a 1100-km "parking" orbit is maintained to await the next payload transfer opportunity. This orbit is below the main proton belt, and thus, little radiation dose is accumulated during this time period. During the second LEO-to-HEEPO transfer, power degrades somewhat further, but power requirements are still met. In comparison, the Europa Mapper SEP vehicle power system had a mass of 150 kg and a thin membrane array area of 100 square meters.

Kerslake, Thomas W.↗
DOE OSTI2026

Mechano-chemical understanding of NaSICON for aqueous redox-flow batteries

Redox-flow batteries utilizing a sodium superionic conductor (NaSICON) can be cost-effective systems for grid energy storage by combining high sodium selectivity with reliance on abundant, low-cost elements. However, improving membrane toughness while maintaining a sufficiently thin membrane for ion conduction is needed. Addressing this issue requires deeper insight into the mechanical properties of NaSICON, its interactions with aqueous chemistries, and the chemo-mechanical degradation mechanisms that arise at the intersection of these phenomena. Here, we provide a framework for understanding these problems, strategies to address them, and highlight the potential of unconventional sintering and thin-film fabrication to optimize the performance of NaSICON in practical flow cells.

Grid energy storage↗
NASA NTRS2002

A Piezoelectric Unimorph Deformable Mirror Concept by Wafer Transfer for Ultra Large Space Telescopes

Future concepts of ultra large space telescopes include segmented silicon mirrors and inflatable polymer mirrors. Primary mirrors for these systems cannot meet optical surface figure requirements and are likely to generate over several microns of wavefront errors. In order to correct for these large wavefront errors, high stroke optical quality deformable mirrors are required. JPL has recently developed a new technology for transferring an entire wafer-level mirror membrane from one substrate to another. A thin membrane, 100 mm in diameter, has been successfully transferred without using adhesives or polymers. The measured peak-to-valley surface error of a transferred and patterned membrane (1 mm x 1 mm x 0.016 mm) is only 9 nm. The mirror element actuation principle is based on a piezoelectric unimorph. A voltage applied to the piezoelectric layer induces stress in the longitudinal direction causing the film to deform and pull on the mirror connected to it. The advantage of this approach is that the small longitudinal strains obtainable from a piezoelectric material at modest voltages are thus translated into large vertical displacements. Modeling is performed for a unimorph membrane consisting of clamped rectangular membrane with a PZT layer with variable dimensions. The membrane transfer technology is combined with the piezoelectric bimorph actuator concept to constitute a compact deformable mirror device with a large stroke actuation of a continuous mirror membrane, resulting in a compact A0 systems for use in ultra large space telescopes.

continuous mirror↗
NASA NTRS1998

Biochemical Capture and Removal of Carbon Dioxide

We devised an enzyme-based facilitated transport membrane bioreactor system to selectively remove carbon dioxide (CO2) from the space station environment. We developed and expressed site-directed enzyme mutants for CO2 capture. Enzyme kinetics showed the mutants to be almost identical to the wild type save at higher pH. Both native enzyme and mutant enzymes were immobilized to different supports including nylons, glasses, sepharose, methacrylate, titanium and nickel. Mutant enzyme could be attached and removed from metal ligand supports and the supports reused at least five times. Membrane systems were constructed to test CO2 selectivity. These included proteic membranes, thin liquid films and enzyme-immobilized teflon membranes. Selectivity ratios of more than 200:1 were obtained for CO2 versus oxygen with CO2 at 0.1%. The data indicate that a membrane based bioreactor can be constructed which could bring CO2 levels close to Earth.

Trachtenberg, Michael C.↗
NASA NTRS1995

Micromachined Silicon Waveguide Circuits

Rectangular waveguides are commonly used as circuit elements in remote-sensing heterodyne receivers at millimeter wavelengths. The advantages of waveguides are low loss and mechanical tunability. However, conventional machining techniques for waveguide components operating above a few hundred GHz are complicated and costly. Waveguides micromachined from silicon however would have several important advantages including low-cost; small size for very high frequency (submillimeter wave) operation; high dimensional accuracy (important for high-Q circuits); atomically smooth walls, thereby reducing rf losses; and the ability to integrate active and passive devices directly in the waveguide on thin membranes, thereby solving the traditional problem of mounting thin substrates.

Silicon Waveguide↗
NASA NTRS2006

Dynamic Analysis of Large In-Space Deployable Membrane Antennas

This paper presents a vibration analysis of an eight-meter diameter membrane reflectarray antenna, which is composed of a thin membrane and a deployable frame. This analysis process has two main steps. In the first step, a two-variable-parameter (2-VP) membrane model is developed to determine the in-plane stress distribution of the membrane due to pre-tensioning, which eventually yields the differential stiffness of the membrane. In the second step, the obtained differential stiffness is incorporated in a dynamic equation governing the transverse vibration of the membrane-frame assembly. This dynamic equation is then solved by a semi-analytical method, called the Distributed Transfer Function Method (DTFM), which produces the natural frequencies and mode shapes of the antenna. The combination of the 2-VP model and the DTFM provides an accurate prediction of the in-plane stress distribution and modes of vibration for the antenna.

vibrations↗
DOE OSTI2025

Size-Selective Nanoporous Atomically Thin Graphene Separators for Lithium–Sulfur Batteries

Lithium–sulfur batteries (LSBs) are extensively researched for their high energy densities but are hindered by the lithium polysulfide (LiPS) shuttling effect, which results in poor cyclability. A popular mitigation strategy is separator modification, where a LiPS trapping material is slurry-coated onto a conventional microporous polypropylene (PP) separator. This additional mass and volume unfortunately compromise the overall energy density of the LSB. This study aims to take a separator modification approach that avoids this issue. Nanoporous atomically thin membranes (NATMs) made of graphene are gaining attention for their scalable synthesis, tunable pore size, and negligible pore length. Herein, we apply a well-characterized graphene NATM for reasons similar to those of a size-selective interlayer in LSBs. The tailored pore size of ∼0.7–1.0 nm and atomic thinness facilitate the passage of Li + (solvated ionic diameters ∼0.54–1.26 nm) and blockage of larger LiPS (solvated ionic diameters ∼0.81–1.69 nm) without adding significant impedances or mass. The sulfur confinement is confirmed through scanning electron microscopy and energy-dispersive X-ray spectroscopy elemental analysis of the Li anode. An LSB with a NATM@PP separator shows virtually no capacity loss over 150 cycles, demonstrating efficacy of size-selective molecular sieving using NATMs in LSBs.

battery separator↗
NASA NTRS1993

Gas phase hydrogen permeation in a Ni-Fe-Co superalloy

Hydrogen permeation measurements have been conducted for the Incoloy 909 Ni-Fe-Co superalloy via the 'membrane' technique, in which the gaseous hydrogen at the entrance of a thin membrane is transposed through the bulk to the exit side of the membrane, at 400-810 C; the pressure range explored was 2.7 x 10 exp 3 to 1.3 x 10 exp 5 N/sq m. The lattice hydrogen solubility of Incoloy 909 is found to be only weakly temperature-dependent. These results are compared with those obtained for Incoloy 903.

Shanabarger, Mickey R.↗
NASA NTRS2019

Advances in Low-Cost Manufacturing and Folding of Solar Sail Membranes

Solar sail membranes must have a high area-to-mass ratio and high solid volume fraction when stowed. In order to meet mission requirements, current solar sail projects, such as NASA’s Near Earth Asteroid Scout, require metallized sail membranes with thicknesses on the order of 2-3 μm. These very thin membranes do not retain creases like thicker membranes, solar panels, or paper models. For Cubesat-class spacecraft, volume, rather than mass, is often the driving requirement for deployable structural elements. These two factors make it both difficult and highly desirable to characterize the practical differences between solar sail membrane packaging methods with laboratory demonstrations. This paper presents lessons gathered from lab work with solar sail membranes at a 10-meter scale.

Stohlman, Olive R.↗
NASA NTRSDate not supplied

Advances in Low-Cost Manufacturing and Folding of Solar Sail Membrane

Solar sail membranes must have a high area-to-mass ratio and high solid volume fraction when stowed. In order to meet mission requirements, current solar sail projects, such as the NASA Near Earth Asteroid Scout and Advanced Composite Solar Sail System, require metallized sail membranes with thicknesses on the order of 2-3 μm. These very thin membranes do not retain creases like thicker membranes, solar panels, or paper models. For CubeSat-class spacecraft, volume, rather than mass, is often the driving requirement for deployable structural elements. These two factors make it both difficult and highly desirable to characterize the practical differences between various membrane designs and packaging methods with laboratory demonstrations. This paper presents lessons gathered from lab work on solar sail membranes at a 9-meter scale. Among other results, laboratory deployment of a full-scale sail quadrant revealed important differences between seaming methods.

Olive R Stohlman↗
DOE OSTI2026

Molecular Modeling of Surfactant Interaction on Phospholipid Bilayers Mimicking Corneal Epithelium

Surfactants found in consumer products can compromise eye corneal membrane integrity upon accidental exposure. Traditional in vitro and in vivo approaches to evaluate membrane–surfactant interaction pose experimental limitations such as species variability, reproducibility, and most often do not provide the overall picture. These limitations motivate the use of in silico models to study phenomena like cellular disruption assays caused by surfactants at the molecular scale. In this work, coarse-grained molecular dynamics simulations have been employed to investigate how nonionic alcohol ethoxylate (AE) and anionic surfactant alcohol ethoxy sulfate (AES) interact with lipid bilayer liposomes that mimic corneal epithelial cell membranes. The spherical liposome is composed of 1,2-dihexadecanoyl-sn-glycero-3-phosphocholine (DPPC), 1,2-di(9Z-octadecenoyl)-sn-glycero-3-phosphoethanolamine (DOPE), 1,2-di(9Z-octadecenoyl)-sn-glycero-3-phospho-l-serine (DOPS), and cholesterol, resembling the composition of the corneal epithelial cells’ membrane bilayer. The simulation consisted of varying degrees of representative surfactant compositions and two initial types of surfactant configurations within or outside the liposome. Our results reveal that both surfactants induce outer leaflet bulging, agreeing with membrane solubilization models. The more highly ethoxylated surfactant, AE, caused more consistent inner leaflet disruption than AES, resulting in significantly more water permeation and membrane thinning. In addition, both surfactants increase the lateral diffusion of lipids within the membrane layers, with higher ethoxylated AE showing a stronger effect than AES. This study demonstrates how surfactant structure and localization influence bilayer membrane integrity, offering mechanistic insights into the irritation potential, thus guiding the rational design of effective surfactant-based formulations.

Lipids↗
DOE OSTI2025

Disentangling the gap between pure and mixed-gas performance of thin film composite membranes through improved cell design and testing methods

Testing thin film composite (TFC) membrane coupons at low stage-cuts (≤5%) in a sweep-gas permeation system is a common practice to obtain mixed-gas separation properties for benchmarking performance and making scale-up decisions. However, even under these idealized conditions, mixed-gas permeance and selectivity can be more than 30% lower than their pure-gas values, partially due to concentration polarization, an effect that typically intensifies with increased membrane permeance. This study investigates the effect of cell design on mixed-gas testing using PolyActive TM TFC membranes with pure-gas CO 2 permeance of 1700 – 3100 gas permeance unit (GPU), covering the permeance range of most state-of-the-art CO 2 /N 2 separation membranes. Here, we designed and 3D-printed a counter-current permeation cell with enhanced feed and sweep flow efficiency, resulting in a 33 – 41% increase in mixed-gas CO 2 permeance compared to traditional permeation cells. Furthermore, we compared sweep-gas and vacuum permeation methods using traditional permeation cells, revealing that the latter delivers 41% higher mixed-gas CO 2 permeance, because vacuuming effectively minimizes the downstream concentration polarization. These findings highlight the importance of cell design and permeation apparatus selection in lab-scale mixed-gas testing, with strong implications for module design and process optimization at the industrial scale.

mixed gas performance↗
NASA NTRS1980

On minimal surfaces, membranes and compressible flows

The theory, variational formulation and finite element analysis of a class of nonlinear problems arising in optimization, thin membrane deflection and compressible flows are developed. Error estimates are summarized, and representative numerical results are presented. Particular theoretical questions pertaining to the existence and uniqueness of solutions are addressed, and their implications for such applications of finite element analysis as the study of compressible flows indicated.

Carey, G. F.↗
DOE OSTI2025

Membrane Thickness Impact on Chemical Degradation Rates

Abstract A comprehensive investigation of PFSA membrane chemical degradation rates as a function of thickness (8-20 µm) is reported. The two-pronged study was conducted on bare membranes and as components of chemically-mitigated and mechanically-reinforced, state-of-the-art (SOA) membrane electrode assemblies (MEAs). The bare membranes were subjected to H2O2 vapor test and MEAs were degraded under OCV conditions, both at 90°C. Both test types employed fluoride release rates (FRR) to monitor chemical degradation rates. Vapor tests revealed that area-specific degradation rates were positively correlated with membrane thickness, but thickness normalized degradation rates were independent of thickness. Open-circuit voltage (OCV) investigations spanning the membrane thickness series of MEAs was probed via a 27-experiment 3(4-1) fractional factorial experimental design. Statistical analysis of the FRR values revealed that chemical degradation rates were dominated by the relative humidity value and that the area-specific degradation rates of MEAs were independent of membrane thickness. The OCV chemical durability insensitivity to membrane thickness is supported by on-load membrane chemical durability studies at the stack level. The results suggest that ,despite smaller ionomer inventory, SOA thin membranes and MEAs are not greatly disadvantaged relative to thicker membranes from a chemical durability perspective, provided oxidative stress levels are controlled throughout application lifetime.

Coms, Frank D. (ORCID:0000000249160350)↗
NASA NTRS1981

Test progress on the electrostatic membrane reflector

An extemely lightweight type of precision reflector antenna, being developed for potential deployment from the space shuttle, uses electrostatic forces to tension a thin membrane and form it into a concave reflector surface. The typical shuttle-deployed antenna would have a diameter of 100 meters and an RMS surface smoothness of 10 to 1 mm for operation at 1 to 10 GHz. NASA Langley Research Center built and is currently testing a subscale (16 foot diameter) model of the membrane reflector portion of such an antenna. Preliminary test results and principal factors affecting surface quality are addressed. Factors included are the effect of the perimeter boundary, splicing of the membrane, the long-scale smoothness of commercial membranes, and the spatial controllability of the membrane using voltage adjustments to alter the electrostatic pressure. Only readily available commercial membranes are considered.

Mihora, D. J.↗
NASA NTRS1981

Test progress on the electrostatic membrane reflector

NASA is currently developing a low mass antenna which derives its reflector surface quality from the application of electrostatic forces to form a thin membrane into the desired concave reflector surface. The shuttle-deployed antenna would have a diameter of 100 m and an RMS surface smoothness of 10 to 1 mm for operation at 1 to 10 GHz. Surface quality measurements have been made on a highly deformable elastic membrane, pressurized by electrostatic forces. Included are the effects of the perimeter boundary, splicing of the membrane, the long-scale smoothness of commercial membranes, and the spatial controllability of the membrane using voltage adjustments to alter the electrostatic forces. The electrostatic membrane was found to operate well in an open-loop sense, showing a high degree of position stability and negligible power consumption in dry air. Visco-electric creep was not evident, but the polymer membrane did expand and contract considerably due to its hygroscopic expansion coefficient. A residual roughness of about 0.75 mm existed with the polymer used in these tests; this error is attributed to seams and membrane anisotropy where the material is stiffer in one direction.

Goslee, J. W.↗
NASA NTRS2003

Membrane Vibration Tests Using Surface-Bonded Piezoelectric Patch Actuation

This paper describes the status of on-going work at the NASA Langley Research Center to measure the dynamics of thin membranes. The test article is a one-meter square pre-tensioned Kapton membrane that incorporates small surface-bonded piezoelectric patches strategically positioned to excite many modes. It is shown that PVDF (polyvinylidene fluoride) and MFC (macro fiber composite) piezoelectric patch actuators provide adequate excitation energy to obtain modal frequencies and mode shapes. Results from modal tests performed on the membrane using piezoelectric patches of different sizes and positions are discussed.

Gasper, James L.↗