Search NASA⌕ Search

SEARCH · Search NASA

Results for “tow tank”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1935

Tank Tests of a Model of a Flying-boat Hull Having a Longitudinally Concave Planing Bottom

The NACA model 11-B, which has a longitudinally concave planing bottom forward of the step, was tested over a wide range of loading. The results of the tests are presented as curves of resistance and trimming moment plotted against speed for various trim angles and as curves of resistance coefficient at best trim angle, and trimming-moment coefficient. The characteristics of the form at the optimum trim are compared with those of NACA model 11-C which has the same form with the exception of a planing bottom longitudinally straight near the step. Photographs of the models being towed in the tank are included for a comparison of the spray patterns. At the best angles of trim in each case model 11-B has lower resistance at high speeds, a higher maximum positive trimming moment near the hump speed, and a more favorable spray pattern than of model 11-C.

Parkinson, J B↗
NASA NTRS1934

The wave suppressor used in the N.A.C.A. tank

So long a time was required for the disturbed water to become quiet after a model had been towed down the N.A.C.A. tank, that only 12 to 18 runs a day could be made. In order to shorten the time lost in waiting between runs, several different methods of suppressing the waves were tried. The most effective form of wave suppressor developed consists of wooden frames covered with fine copper screening and secured horizontally just beneath the surface of the water at the sides of the tank. With these suppressor placed every 50 feet along the length of the tank, 40 to 60 test runs a day can be made.

Truscott, Starr↗
NASA NTRS1934

Tank tests of a family of flying-boat hulls

This report presents towing tests made in the N.A.C.A. tank of a parent form and five variations of a flying-boat hull. The beams of two of the derived forms were made the same as that of the parent and the lengths changed by increasing and decreasing the spacing of stations. The lengths of the two others of the derived forms were made the same as that of the parent while the beams were changed by increasing and decreasing the spacing of buttocks, all other widths being changed in proportion. The remaining derived form has the same length and beam as the parent, but the lines of the forebody were altered to give a planing bottom with no longitudinal curvature forward of the step. The test data were analyzed to determine the minimum resistance and the angle at which it occurs for all speeds and loads. The results of this analysis are given in the form of non dimensional curves for each model. The effect of variation in over-all size, as indicated by a "complete" test on any given hull, is pointed out. The effect of changing length alone by the spacing of buttocks, as well as the effects of the changes in length-beam ratio and longitudinal curvature that result from these operations are discussed. The difficulties encountered in interpreting test results of systematic families derived by the method used are emphasized. Further studies are suggested in which changes in the variable under consideration would not be obscured by secondary changes in other important variables.

Shoemaker, James M↗
NASA NTRS1938

On the determination of the take-off characteristics of a seaplane

The present paper presents an attempt to coordinate the available theoretical and experimental data on planing surfaces so as to develop an approximate analytical method for the determination of the water resistance of a seaplane without any preliminary towing tests in the tank.

Perelmuter, A↗
NASA NTRS1950

Hydrodynamic Properties of Planing Surfaces and Flying Boats

The study of the hydrodynamic properties of planing bottom of flying boats and seaplane floats is at the present time based exclusively on the curves of towing tests conducted in tanks. In order to provide a rational basis for the test procedure in tanks and practical design data, a theoretical study must be made of the flow at the step and relations derived that show not only qualitatively but quantitatively the inter-relations of the various factors involved. The general solution of the problem of the development of hydrodynamic forces during the motion of the seaplane float or flying boat is very difficult for it is necessary to give a three-dimensional solution, which does not always permit reducing the analysis to the form of workable computation formulas. On the other had, the problem is complicated by the fact that the object of the analysis is concerned with two fluid mediums, namely, air and water, which have a surface of density discontinuity between them. The theoretical and experimental investigations on the hydrodynamics of a ship cannot be completely carried over to the design of floats and flying-boat hulls, because of the difference in the shape of the contour lines of the bodies, and, because of the entirely different flow conditions from the hydrodynamic viewpoint.

Sokolov, N. A.↗
NASA NTRS1961

Ground Influence on a Model Airfoil with a Jet-Augmented Flap as Determined by Two Techniques

An investigation was made in the Langley 300-MPH 7- by 10-foot tunnel with a conventional ground-board setup and in the Langley tank no. 1 by using the tow carriage to move the model over a ground board to evaluate the simulation of flight conditions in ground influence with a conventional ground-board setup. The 12-percent-thick airfoil was unswept and untapered with an aspect ratio of 6.0 and had a 10 percent- chord jet-augmented flap. From this investigation it appears that the loss in lift of an airfoil with a jet-augmented flap in ground influence as determined in a wind tunnel with a conventional ground-board setup is considerably larger than would be obtained in free flight.

Turner, Thomas R.↗
NASA NTRS2017

Design, Manufacture and Test of Cryotank Components

On the composite cryotank technology development (CCTD) project, the Boeing Company built two cryotanks as a means of advancing technology and manufacturing readiness levels (TRL and MRL) and lowering the risk of fabricating full-scale fuel containment vessels.1 CCTD focused on upper stage extended duration applications where long term storage of propellants is required. The project involved the design, analysis, fabrication, and test of manufacturing demonstration units (MDU), a 2.4 m (precursor) and a 5.5 m composite cryotank. Key design features included one-piece wall construction to minimize overall weight (eliminating the need for a bellyband joint), 3-dimensionally (3D) reinforced y-joint material to alleviate stress concentrations at the tank to skirt interface and a purge-able fluted core skirt to carry high axial launch loads. The tanks were made with OoA curing pre-impregnated (prepreg) carbon/epoxy (C/E) slit-tape tow (STT) that contained thin micro-crack resistant plies in the tank wall center to impede permeation. The tanks were fabricated at Boeing's Seattle-based Advanced Development Center (ADC) using RAFP and multipiece break-down tooling. The tooling was designed and built by Janicki Industries (JI) at Sedro Woolley, Washington. Tank assemblage consisted of co-bonded dome covers, one-piece fluted core skirts and mechanical fastened cover/sump. Ultrasonic inspection was performed after every cure or bond and a structural health monitoring system (SHMS) was installed to identify potential impact damage events (in-process and/or during transportation). The tanks were low temperature tested at NASA's George C. Marshall Space Flight Center (MSFC) in Huntsville, Alabama. The testing, which consisted of a sequence of fill/drain pressure and thermal cycles using LH2, was successfully concluded in 2012 on the 2.4 m tank and in 2014 on the 5.5 m tank. Structural, thermal, and permeation performance data was obtained. 2 Critical design features and manufacturing advancements, which helped to validate 25% weight and 30% cost reduction projections, were matured. These advancements will help to guide future composite tank integration activities on next generation long duration aircraft and space launch vehicles. Because CCTD addressed innovative design features, heavy lift size scale-up, multipiece captured tooling, new generation automated material placement (AMP) equipment and OoA materials, this chapter should be of interest to educators, students and manufacturers of composite hardware and flight vehicles.

McCarville, Douglas A.↗
NASA NTRS1974

Correlation for estimating vortex rotational velocity downstream dependence

Description of a correlation, derived from water tank measurements in the wake of wings towed under water, that makes it possible to predict the downstream distance behind an aircraft in flight where its trailing vortex will begin to decay. Comparisons of measured and predicted data are discussed.

Ciffone, D. L.↗
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-boat Hull - N.A.C.A. Model No.11-A

Model No. 11-A was designed as an improvement over N.A.C.A. Model No. 11, a complete test of which is described in N.A.C.A. Technical Note No. 464. In contrast with the longitudinal upward curvature in the planing bottom forward of the main step on Model 11-A was made as flat as practicable. Otherwise, the two models have very nearly the same form. The results of towing tests made on Model 11-A in the N.A.C.A. tank over a wide range of speed, load on the water, and trim angle are presented, both as original test data and as non dimensional coefficients. A comparison is made with similar results from the test of Model No. 11. The practical significance of the improvement obtained is demonstrated by applying the data from the new form to the illustrative design problem use in the note on Model NO. 11.

Parkinson, John B↗
NASA NTRS1991

STS-39 Discovery in the VAB and Columbia Tow From HB-2

The orbiter Discovery sits inside the Vehicle Assembly Building (VAB) after its rollover from the Orbiter Processing Facility (OPF). In the VAB, Discovery will be mated with an external tank and solid rocket boosters for its launch. Shown also is Columbia orbiter being towed from the High Bay 2.

Source record↗
NASA NTRS1934

Tank Tests of Auxiliary Vanes as a Substitute for Planing Area

The results of towing tests made on two models at the request of the Bureau of Aeronautics, Navy Department, are presented. The first model represents the hull of the U.S. Navy PN-8 flying boat, in which the sponsors of the original hull are removed and auxiliary lifting vanes are fitted at the chines immediately forward of the main step. The tests showed that the altered form gave a large increase in hump resistance and a very undesirable spray formation through a large part of the speed range.

Parkinson, John B↗
NASA NTRS2018

Fabrication of a Composite Tow-Steered Structure for Air-Launch Vehicle Applications

Generation Orbit (GO) is developing the GO Launcher-1 (GO-1), a single stage liquid rocket that is launched from a Gulfstream III carrier aircraft platform. The vehicle is designed as the next generation platform for hypersonic flight testing and suborbital microgravity research. To reduce mass and increase payload, GO partnered with NASA Langley Research Center to design, analyze, optimize, and fabricate a tow-steered manufacturing development unit of a cylindrical section of a liquid oxygen tank. The fabrication process of using the ISAAC (Integrated Structural Assembly of Advanced Composites) system is described. The structural design challenges and the concept design solutions are also presented to provide the context for the fabrication process. The in-situ nondestructive evaluation supporting the effort is also described.

Grenoble, Ray↗
NASA NTRS1985

External tank processing from barge to pad

Delivery and launch readiness events for the External Tanks (ET) are discussed. The ET is off-loaded at the KSC Barge Turning Basin and towed to the Vertical Assembly Building (VAB), High Bay Transfer Aisle. It is erected vertically and placed in the ET Checkout Area of High Bay 2 or 4 for standalone checkout. At the completion of checkout the ET is transferred to storage or to the Integration Area of High Bay 1 or 3 for SRB and Orbiter Mate. A Systems Integration Test performed with the Orbiter and Solid Rocket Booster is described. Final checkout activities are also described.

Carpenter, J. E.↗
NASA NTRS1942

An Investigation of Hydrofoils in the NACA Tank I : Effect of Dihedral and Depth of Submersion

Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.

HYDROFOILS - NACA - CHARACTERISTICS TANK TESTS (NA↗
NASA NTRS2005

STS-114: Discovery Mission Status Briefing

Phil Engelauf, STS-114 Mission Operations Representative reports: the orbital rendezvous was successful, and today's activities includes initial preparations of the next day's extravehicular activities (EVA); he specifically mentioned tile repair, wiring on the outside of the vehicle to try to recover CMG2 (Control Moment Gyro), and preparation for the external stowage platform. John Shannon, Manager of the Space Shuttle Operations and Integration reports from Engineering standpoint that the composites of the underside of the tile surface seen from pictures taken during the pitch maneuver were extremely clean; the Engineering staff continues to look at the focus inspection data from the orbital boom sensor system (OBSS) and other data to assess the condition of the vehicle. Solid rocket boosters were retrieved and are towed back to the Air Force hangar in Cape Carneval. Six target inspection (nose gear doors, gap fillers, chine area, external tank doors, trailing edge, and ice), and arm operations, foam, conservation measures, shuttle air lock, aerodynamics assessment and re-entry were topics covered with the News media.

Source record↗
NASA NTRS1939

The Enlarged N.A.C.A. Tank, and Some of Its Work

The most conspicuous of the features of the enlarged N.A.C.A. tank are derived directly from those of the original tank and owe their present form not only to the reasons for their first use but also to the experience obtained with them. As in the original tank, there are: 1) A basin of great length (new 2,880 feet); 2) Rails made of structural H beams, without machining; 3) A towing carriage of very high speed (now 80 mph maximum); 4) Rubber tires on all the wheels, pneumatic on the running wheels and solid on the guide wheels.

Truscott, Starr↗
DOE OSTI2022

Melt-Spun PAN Precursor for Cost-Effective Carbon Fibers in High Pressure Compressed Gas Tankage

The objective of this program was to synthesize melt-spinnable polyacrylonitrile (PAN) precursor that will lead to carbon fiber 25% less expensive than carbon fiber produced from conventional PAN precursor when produced in large volumes. The carbon fiber produced from this precursor needs to achieve ≥ 700 ksi tensile strength with this cost reduction to replace the incumbent fiber. In this program, the technology for producing precursor and then converted carbon fiber (CF) capable of meeting the 700 ksi target was to be demonstrated at a small scale in tows, containing ≥ 100 filaments. If this program moved on to a “Phase 2”, the processes would be scaled up to produce and test Type IV compressed gas storage tanks capable of meeting the 700-bar ultimate targeted FOA performance level. Precursor fiber production typically contributes a large fraction (~50%) to finished CF manufactured cost. Presently, all high strength CFs are manufactured from solution spun PAN precursor, accomplished at low temperatures using large amounts of environmentally unfriendly solvents that impart major impact to line speed and costs involved with handling and reclaiming the solvents and associated “waste streams” required in spinning and extracting those solvents. PAN melt spinning was demonstrated by the company BASF in CF precursor production and used in production of some other acrylic fibers, but significant production challenges remain for meeting the established CF metrics. Melt spinning requires use of plasticizers to suppress the melt temperature of the predominantly PAN formulation to a point sufficiently below the temperature of significant cross-linking. Fortunately, BASF and this team’s earlier work had demonstrated acrylic formulations melt spun with combinations of plasticizing solvents at much lower solvent levels. This project team made significant progress in understanding technical issues and identifying formulation pathways in earlier work in this area where >250ksi strength was achieved. The goal of this program was to pursue a more comprehensive approach with a larger, more diverse team having greater equipment design and overall production capabilities to push rapidly beyond the science to resolve remaining “engineering” issues associated with establishing stable, continuous processes for precursor fiber leading to enhanced, cost-effective CF and composite tank production.

36 MATERIALS SCIENCE↗