Results for “truncation” — Page 3

NASA NTRS1981

A study of the modal truncation error in the component mode analysis of a dual-rotor system

In the component mode synthesis method, the equation of motion in the generalized coordinates is built upon the undamped eigenvalue data of the component structures. Error is inevitable when truncated modes are used. In this paper, two modal truncation schemes were evaluated with regard to the critical speed, stability, and unbalance response of a two-spool gas turbine engine. The numbers of modes required to yield acceptable accuracy in these cases were determined. Guidelines for modal truncation were derived from these results.

Li, D. F.↗

NASA NTRS1982

Sensitivity of selected geomagnetic properties to truncation level of spherical harmonic expansions

The model dependence of Gauss coefficients associated with a lack of spherical harmonic orthogonality on a nonuniform Magsat data grid is shown to be minor, where the fitting level exceeds the harmonic order by a value of approximately four. The shape of the magnetic energy spectrum outside the core, and the sensitivity to truncation level of magnetic contour location and the number of their intersections on the core-mantle boundary, suggest that spherical harmonic expansions of the main geomagnetic field should be truncated at a truncation level value of not more than eight if they are to be extrapolated to the core.

Benton, E. R.↗

NASA NTRS1987

The effect of modal truncation on modal modification

Several investigators have shown that the ability of modal modification routines to accurately predict dynamic structural changes is highly dependent on the completeness of the original modal database of the structure-modal truncation. This paper more closely examines the effects of modal truncation on modal modifications. The results of this study show the modified modal vector to be a weighted linear sum of the original modal vectors. Due to this weighted linear sum process, modal truncation might affect almost any mode in a modification process. Therefore, the quality of a modal modification is not necessarily dependent on the number of modes present in a database, but more importantly on which modes are present.

Elliott, K. B.↗

NASA NTRS1991

Truncation length for Viterbi decoding

A bound is derived and analyzed for the bit error rate (BER) of a Viterbi decoder with survivor truncation. Estimates of the SNR (signal-to-noise ratio) loss on the AWGN (additive white Gaussian noise) channel due to truncation are obtained for convolutional codes. Larger truncation lengths are required than the smallest value that does not effectively decrease the code's free distance, especially at low Eb/N0.

Onyszchuk, Ivan M.↗

NASA NTRS1995

Performance of an artificial absorber for truncating FEM meshes

We investigate the effectiveness of an artificial absorber for truncating finite element (FE) meshes. Specifically, we present the implementation of a novel mesh truncation approach using a perfectly matched anisotropic absorber for waveguides and stripline circuits. This truncation scheme is useful in many applications, including antennas, scattering, and microwave circuits.

Gong, Jian↗

NASA NTRS2001

Truncated hexa-octahedral magnetite crystals in ALH84001: presumptive biosignatures

McKay et al. [(1996) Science 273, 924-930] suggested that carbonate globules in the meteorite ALH84001 contained the fossil remains of Martian microbes. We have characterized a subpopulation of magnetite (Fe(3)O(4)) crystals present in abundance within the Fe-rich rims of these carbonate globules. We find these Martian magnetites to be both chemically and physically identical to terrestrial, biogenically precipitated, intracellular magnetites produced by magnetotactic bacteria strain MV-1. Specifically, both magnetite populations are single-domain and chemically pure, and exhibit a unique crystal habit we describe as truncated hexa-octahedral. There are no known reports of inorganic processes to explain the observation of truncated hexa-octahedral magnetites in a terrestrial sample. In bacteria strain MV-1 their presence is therefore likely a product of Natural Selection. Unless there is an unknown and unexplained inorganic process on Mars that is conspicuously absent on the Earth and forms truncated hexa-octahedral magnetites, we suggest that these magnetite crystals in the Martian meteorite ALH84001 were likely produced by a biogenic process. As such, these crystals are interpreted as Martian magnetofossils and constitute evidence of the oldest life yet found.

Oxides/chemistry↗

NASA NTRS2006

Constrained Kalman Filtering Via Density Function Truncation for Turbofan Engine Health Estimation

Kalman filters are often used to estimate the state variables of a dynamic system. However, in the application of Kalman filters some known signal information is often either ignored or dealt with heuristically. For instance, state variable constraints (which may be based on physical considerations) are often neglected because they do not fit easily into the structure of the Kalman filter. This paper develops an analytic method of incorporating state variable inequality constraints in the Kalman filter. The resultant filter truncates the PDF (probability density function) of the Kalman filter estimate at the known constraints and then computes the constrained filter estimate as the mean of the truncated PDF. The incorporation of state variable constraints increases the computational effort of the filter but significantly improves its estimation accuracy. The improvement is demonstrated via simulation results obtained from a turbofan engine model. The turbofan engine model contains 3 state variables, 11 measurements, and 10 component health parameters. It is also shown that the truncated Kalman filter may be a more accurate way of incorporating inequality constraints than other constrained filters (e.g., the projection approach to constrained filtering).

Simon, Dan↗

NASA NTRS2022

The Long-stable Hard State of XTE J1752-223 and the Disk Truncation Dilemma

The degree to which the thin accretion disks of black hole X-ray binaries are truncated during hard spectral states remains a contentious open question in black hole astrophysics. During its singular observed outburst in 2009–2010, the black hole X-ray binary XTE J1752−223 spent ∼1 month in a long-stable hard spectral state at a luminosity of ∼0.02–0.1 L Edd . It was observed with 56 RXTE pointings during this period, with simultaneous Swift-XRT daily coverage during the first 10 days of the RXTE observations. While reflection modeling has been extensively explored in the analysis of these data, there is disagreement surrounding the geometry of the accretion disk and corona implied by the reflection features. We reexamine the combined, high signal-to-noise, simultaneous Swift and RXTE observations, and perform extensive reflection modeling with the latest relxill suite of reflection models, including newer high disk density models. We show that reflection modeling requires that the disk be within ∼5 R ISCO during the hard spectral state, while weaker constraints from the thermal disk emission imply higher truncation (Rin = 6–80 R ISCO ). We also explore more complex coronal continuum models, allowing for two Comptonization components instead of one, and show that the reflection features still require only a mildly truncated disk. Finally we present a full comparison of our results to previous constraints found from analyses of the same data set.

Accretion↗

NASA NTRSDate not supplied

Alternate Methods of Model Reduction to Avoid Dynamic Modal Truncation Error

Loads analysis is traditionally performed using dynamically reduced models, which provides the benefit to reduce run time. If the reduced model frequency cutoff is not chosen appropriately, the model will lack the dynamic content required to fully represent the response of the non-reduced model. Standard guidance for reduced model frequency content, provided in NASA-STD-5002, is to solve fixed base modes up to a minimum of 1.5x the model frequency content of interest and to employ static modal truncation methods such as residual vectors, the mode acceleration method, and the residual flexibility method to account for the truncated flexibility of the missing modes. Fixed base modes require the selection of a set of degrees of freedom to be constrained which, if not properly selected, may affect the accuracy of the reduced model by excluding some of the dynamic characteristic of the full model. In this case, the standard NASA guidance would be insufficient, but it may not be readily apparent that a portion of the reduced model response is missing. This error was encountered during an independent verification and validation (IV&V) effort, where it was observed that the resulting dynamic response was lower than the inline analysis. In this specific case, despite following the standard NASA model reduction guidelines in the selection of the frequency cutoff, the inline model still did not fully capture the necessary dynamic content. As part of the IV&V, an alternate reduction methodology was employed using an unconstrained mode acceleration method. The original model initially performed a constrained reduction to twice the frequency content of interest before doing a free-free run, employing the mode acceleration method to account for the truncated modes. In contrast in the IV&V, the unconstrained model reduced directly to the needed frequency content of the free-free run, avoiding any interactions between constraints and dynamic content. To verify the model, the original reduction methodology was used to generate a series of Hurty-Craig-Bampton reductions, each with a higher frequency cutoff than the previous. The results were shown to converge once the frequency cutoff increased past eight times the frequency content of interest. At the same frequency cutoff, the results of the Hurty-Craig-Bampton model converged with the results of the unconstrained mode acceleration model. This comparative study provided confidence that the results of the unconstrained modal acceleration reduced model were correct and that the Hurty-Craig-Bampton needed to increase its frequency cutoff to fully capture the dynamic response.

Erin Simmons↗

NASA NTRSDate not supplied

Alternate Methods of Model Reduction to Avoid Dynamic Modal Truncation Error

Loads analysis is traditionally performed using dynamically reduced models, which provides the benefit to reduce run time. If the reduced model frequency cutoff is not chosen appropriately, the model will lack the dynamic content required to fully represent the response of the non-reduced model. Standard guidance for reduced model frequency content, provided in NASA-STD-5002, is to solve fixed base modes up to a minimum of 1.5x the model frequency content of interest and to employ static modal truncation methods such as residual vectors, the mode acceleration method, and the residual flexibility method to account for the truncated flexibility of the missing modes. Fixed base modes require the selection of a set of degrees of freedom to be constrained which, if not properly selected, may affect the accuracy of the reduced model by excluding some of the dynamic characteristic of the full model. In this case, the standard NASA guidance would be insufficient, but it may not be readily apparent that a portion of the reduced model response is missing. This error was encountered during an independent verification and validation (IV&V) effort, where it was observed that the resulting dynamic response was lower than the inline analysis. In this specific case, despite following the standard NASA model reduction guidelines in the selection of the frequency cutoff, the inline model still did not fully capture the necessary dynamic content. As part of the IV&V, an alternate reduction methodology was employed using an unconstrained mode acceleration method. The original model initially performed a constrained reduction to twice the frequency content of interest before doing a free-free run, employing the mode acceleration method to account for the truncated modes. In contrast in the IV&V, the unconstrained model reduced directly to the needed frequency content of the free-free run, avoiding any interactions between constraints and dynamic content. To verify the model, the original reduction methodology was used to generate a series of Hurty-Craig-Bampton reductions, each with a higher frequency cutoff than the previous. The results were shown to converge once the frequency cutoff increased past eight times the frequency content of interest. At the same frequency cutoff, the results of the Hurty-Craig-Bampton model converged with the results of the unconstrained mode acceleration model. This comparative study provided confidence that the results of the unconstrained modal acceleration reduced model were correct and that the Hurty-Craig-Bampton needed to increase its frequency cutoff to fully capture the dynamic response.

Erin Simmons↗

DOE OSTI2020

Reshaping of Truncated Pd Nanocubes: Energetic and Kinetic Analysis Integrating Transmission Electron Microscopy with Atomistic-Level and Coarse-Grained Modeling

Stability against reshaping of metallic fcc nanocrystals synthesized with tailored far-from-equilibrium shapes is key to maintaining optimal properties for applications such as catalysis. Yet Arrhenius analysis of experimental reshaping kinetics, and appropriate theory and simulation, is lacking. As such, we use TEM to monitor the reshaping of Pd nanocubes of ~25 nm side length between 410 °C (over ~4.5 h) and 440 °C (over ~0.25 h), extracting a high effective energy barrier of E eff ≈ 4.6 eV. We also provide an analytic determination of the energy variation along the optimal pathway for reshaping that involves transfer of atoms across the nanocube surface from edges or corners to form new layers on side {100} facets. The effective barrier from this analysis is shown to increase strongly with the degree of truncation of edges and corners in the synthesized nanocube. Theory matches experiment for the appropriate degree of truncation. In addition, we perform simulations of a stochastic atomistic-level model incorporating a realistic description of diffusive hopping for undercoordinated surface atoms, thereby providing a visualization of the initial reshaping process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Predicting Damages to Remainder Parcels in Right-of-Way Acquisitions for Expanding Transportation Infrastructure: Using a Truncated Finite-Mixture Model

Right-of-way acquisition is a critical component of transportation infrastructure development. Transportation infrastructure projects cannot proceed without proper right-of-way acquisition or may face significant delays. State Departments of Transportation frequently acquire parcels of land for roadway expansion projects. A majority of these acquisitions can be partial takings, referring to a portion of a parcel that is acquired. The remainder of the property usually suffers economic changes due to the partial acquisition, which can be calculated as damage percentages. The damage percentage represents the extent to which the remaining land or property value has been diminished due to the acquisition. It reflects the remaining property value percentage that may have been lost or compromised due to the acquisition. Here, this study aims to provide a robust model to estimate damage percentages to the remainder parcels that may help state Departments of Transportation appraisers make early predictions about the damages in cases involving partial takings. The research uses 509 appraisal reports from the Tennessee Department of Transportation to identify the key parcel attributes that influence the percentage of damages. Three regression models are developed: a linear regression model, a finite-mixture model (FMM), and a truncated FMM with two latent classes. The modeling results show that the truncated FMM with two classes outperforms the other models. To validate the models, actual sales data is collected and analyzed for 59 properties, and the results suggest that the model predictions are fairly accurate. A predictive tool is developed based on the models to help appraisers anticipate right-of-way damages under different scenarios and can provide early predictions about the damages.

42 ENGINEERING↗

DOE OSTI2022

Zero-Truncated Poisson Tensor Decomposition for Sparse Count Data

We propose a novel statistical inference paradigm for zero-inflated multiway count data that dispenses with the need to distinguish between true and false zero counts. Our approach ignores all zero entries and applies zero-truncated Poisson regression on the positive counts. Inference is accomplished via tensor completion that imposes low-rank structure on the Poisson parameter space. Our main result shows that an $\textit{N}$-way rank-R parametric tensor 𝓜 ϵ (0, ∞) $I$Χ∙∙∙Χ$I$ generating Poisson observations can be accurately estimated from approximately $IR^2 \text{log}^2_2(I)$ non-zero counts for a nonnegative canonical polyadic decomposition. Several numerical experiments are presented demonstrating that our zero-truncated paradigm is comparable to the ideal scenario where the locations of false zero counts are known $\textit{a priori}$.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

Coordination of Anle138b to Silver Results in Selective Reduction of a C-terminal truncated Alpha-synuclein Protein and Increased Aggregate Size

Parkinson’s disease (PD) is a prevalent age-related neurodegenerative syndrome, partially thought to be caused by a decrease in alpha-synuclein proteostasis. Anle138b = 5-(1,3-benzodioxol-5-yl)-3-(3-bromophenyl)-1H-pyrazole (HL), is undergoing clinical trials as a promising mitigator of alpha-synuclein aggregation. Because complexation to metals is known to modulate the activity of several drugs, we have prepared and characterized: H2L(ClO4), [CuI(µ-L)]3, and [AgI(µ-L)]3. To better understand the bioviability of these compounds, we monitored their effects in a cell culture model of alpha-synuclein protein aggregation using human alpha-synuclein pre-formed fibrils (PFFs). Using two different anti-alpha-synuclein antibodies, our data suggests that [AgI(µ-L)]3 decreases a C-terminal truncated protein that is approximately 12.4 kDa, as well as increases the size and alters the shape of PFF-induced aggregates. This indicates that [AgI(µ-L)]3 impacts aggregation in a manner different from HL and may serve as a novel tool for studying C-terminal truncation related aggregation chemistry.

Rue, Kelly L.↗

DOE OSTI2021

Solving the 2D SUSY Gross-Neveu-Yukawa model with conformal truncation

We use Lightcone Conformal Truncation to analyze the RG flow of the two-dimensional supersymmetric Gross-Neveu-Yukawa theory, i.e. the theory of a real scalar superfield with a $\mathbb{Z}$ 2 -symmetric cubic superpotential, aka the 2d Wess-Zumino model. The theory depends on a single dimensionless coupling $\overline{g}$, and is expected to have a critical point at a tuned value ${\overline{g}}_{\ast }$ where it flows in the IR to the Tricritical Ising Model (TIM); the theory spontaneously breaks the $\mathbb{Z}$ 2 symmetry on one side of this phase transition, and breaks SUSY on the other side. We calculate the spectrum of energies as a function of $\overline{g}$ and see the gap close as the critical point is approached, and numerically read off the critical exponent ν in TIM. Beyond the critical point, the gap remains nearly zero, in agreement with the expectation of a massless Goldstino. We also study spectral functions of local operators on both sides of the phase transition and compare to analytic predictions where possible. In particular, we use the Zamolodchikov C -function to map the entire phase diagram of the theory. Crucial to this analysis is the fact that our truncation is able to preserve supersymmetry sufficiently to avoid any additional fine tuning.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

Bootstrapping 2d ϕ 4 theory with Hamiltonian truncation data

We combine the methods of Hamiltonian Truncation and the recently proposed generalisation of the S-matrix bootstrap that includes local operators to determine the two-particle scattering amplitude and the two-particle form factor of the stress tensor at s > 0 in the 2d Φ 4 theory. We use the form factor of the stress tensor at s ≤ 0 and its spectral density computed using Lightcone Conformal Truncation (LCT), and inject them into the generalized S-matrix bootstrap set-up. The obtained results for the scattering amplitude and the form factor are fully reliable only in the elastic regime. We independently construct the “pure” S-matrix bootstrap bounds (bootstrap without including matrix elements of local operators), and find that the sinh-Gordon model and its analytic continuation the “staircase model” saturate these bounds. Surprisingly, the Φ 4 two-particle scattering amplitude also very nearly saturates these bounds, and moreover is extremely close to that of the sinh-Gordon/staircase model.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2024

Rounding out the story of higher derivative consistent truncations

At the two-derivative order, the group manifold reduction of heterotic supergravity on S 3 results in a half-maximal 7D gauged supergravity coupled to three vector multiplets, and a further truncation can be taken to remove the vector multiplets. We demonstrate that this truncation remains consistent at the four-derivative level; we do so both by analysis of the equations of motion and the supersymmetry variations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

Form factors and spectral densities from Lightcone Conformal Truncation

We use the method of Lightcone Conformal Truncation (LCT) to obtain form factors and spectral densities of local operators $\mathcal{O}$ in $\phi^4$ theory in two dimensions. We show how to use the Hamiltonian eigenstates from LCT to obtain form factors that are matrix elements of a local operator $\mathcal{O}$ between single-particle bra and ket states, and we develop methods that significantly reduce errors resulting from the finite truncation of the Hilbert space. We extrapolate these form factors as a function of momentum to the regime where, by crossing symmetry, they are form factors of $\mathcal{O}$ between the vacuum and a two-particle asymptotic scattering state. We also compute the momentum-space time-ordered two-point functions of local operators in LCT. These converge quickly at momenta away from branch cuts, allowing us to indirectly obtain the time-ordered correlator and the spectral density at the branch cuts. We focus on the case where the local operator $\mathcal{O}$ is the trace Θ of the stress tensor.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗