Search NASA⌕ Search

SEARCH · Search NASA

Results for “turbofan”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft.

This paper presents the results of an analytical study of the dynamics and control of turbofan lift engines, and proposes methods of meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed.

Sellers, J. F.↗
NASA NTRS1973

Study of small turbofan engines applicable to general-aviation aircraft

The applicability of small turbofan engines to general aviation aircraft is discussed. The engine and engine/airplane performance, weight, size, and cost interrelationships are examined. The effects of specific engine noise constraints are evaluated. The factors inhibiting the use of turbofan engines in general aviation aircraft are identified.

Merrill, G. L.↗
NASA NTRS1975

Acoustic characteristics of a large upper-surface blown configuration with turbofan engines

This paper presents acoustic results from static and simulated low forward velocity tests of a large-scale model of an aircraft configuration with two turbofan engines in the full-scale tunnel at the Langley Research Center. The turbofan engines were integrated into the model and equipped with rectangular nozzles to provide the upper-surface blowing. Results indicate that the upper-surface-blowing noise problem can be characterized, primarily, by the unsymmetrical radiation pattern due mainly to shielding of the high-frequency engine noise and the production of low-frequency noise by jet-surface interaction. The directivity of the low-frequency noise was found to depend on the trailing-edge flap angle when the thrust levels were low. Normalized sound pressure level spectral density data showed good agreement at low Strouhal number with other small- and large-scale model data from tests using simulated wing-flap systems. Forward speed effects were undetectable at the low tunnel speeds used during the tests.

Preisser, J. S.↗
NASA NTRS1975

Preliminary evaluation of a heat pipe heat exchanger on a regenerative turbofan

A preliminary evaluation was made of a regenerative turbofan engine using a heat pipe heat exchanger. The heat exchanger had an effectiveness of 0.70, a pressure drop of 3 percent on each side, and used sodium for the working fluid in the stainless steel heat pipes. The engine was compared to a reference turbofan engine originally designed for service in 1979. Both engines had a bypass ratio of 4.5 and a fan pressure ratio of 2.0. The design thrust of the engines was in the 4000 N range at a cruise condition of Mach 0.98 and 11.6 km. It is shown that heat pipe heat exchangers of this type cause a large weight and size problem for the engine. The penalties were too severe to be overcome by the small uninstalled fuel consumption advantage. The type of heat exchanger should only be considered for small airflow engines in flight applications. Ground applications might prove more suitable and flexible.

Kraft, G. A.↗
NASA NTRS1976

Study of turbofan engines designed for low energy consumption

The near-term technology improvements which can reduce the fuel consumed in the JT9D, JT8D, and JT3D turbofans in commercial fleet operation through the 1980's are identified. Projected technology advances are identified and evaluated for new turbofans to be developed after 1985. Programs are recommended for developing the necessary technology.

Gray, D. E.↗
NASA NTRS1975

An early glimpse at long-term subsonic commercial turbofan technology requirements

This paper reports on the exploratory investigation and initial findings of the study of future turbofan concepts to conserve fuel. To date, these studies have indicated a potential reduction in cruise thrust specific fuel consumption in 1990 turbofans of approximately 15% relative to present day new engines through advances in internal aerodynamics, structure-mechanics, and materials. Advanced materials also offer the potential for fuel savings through engine weight reduction. Further studies are required to balance fuel consumption reduction with sound airlines operational economics.

Gray, D. E.↗
NASA NTRS1976

Jet noise characteristics of unsuppressed duct burning turbofan exhaust system

Recent aero-acoustic tests of model coannular nozzles have shown that less noise is generated if the higher-velocity jet is exhausted from the outer annular passage rather than from the primary nozzle. These findings are of particular significance to a duct-burning turbofan (DBTF) engine being studied for application to an advanced supersonic transport. Unlike conventional turbofan engines that have peak velocities from the primary nozzle, it is possible to design a DBTF engine to have a fan velocity higher than that of the primary flow. Results are presented for a NASA-sponsored model test program that covers a range of fan to primary-area ratios from 0.75 to 1.2, and a range of fan to primary-velocity ratios from 0.4 to 2.8. Correlations are given that relate radiated sound power to fan velocity, fan to primary-velocity ratio, and fan to primary-area ratio. Corresponding exhaust-plume velocity-traverse data are presented which suggest that the observed noise benefits may be due to the more rapid decay of the annular flow because of shear stresses on the inner surface that result from the lower-velocity primary flow.

Packman, A. B.↗
NASA NTRS1976

Study of small turbofan engines applicable to single-engine light airplanes

The design, efficiency and cost factors are investigated for application of turbofan propulsion engines to single engine, general aviation light airplanes. A companion study of a hypothetical engine family of a thrust range suitable to such aircraft and having a high degree of commonality of design features and parts is presented. Future turbofan powered light airplanes can have a lower fuel consumption, lower weight, reduced airframe maintenance requirements and improved engine overhaul periods as compared to current piston engined powered airplanes. Achievement of compliance with noise and chemical emission regulations is expected without impairing performance, operating cost or safety.

Merrill, G. L.↗
NASA NTRS1976

A program for calculating turbofan-driven lift-fan propulsion system performance

The performance of a turbofan-powered lift fan propulsion system for vertical takeoff and landing (VTOL) aircraft is calculated. The program formulation consists of taking bleed air from a turbofan engine, heating the bleed air in an interburner, and passing it through a tip turbine to drive a lift fan. Two options are available: bleed air from the engine exhaust, or bleed air that has passed through the engine fan only. This computer program will benefit persons unfamiliar with the thermodynamics of engine cycle analysis.

Tauber, M. E.↗
NASA NTRS1977

Use of finite element techniques in the determination of the acoustic properties of turbofan inlets

This paper describes the application of the finite-element method in combination with Galerkin's method in the determination of the acoustic properties of turbofan inlets containing high-subsonic-Mach-number flows. An approximate solution to the steady inviscid flow field is obtained using an integral method for calculating the potential flow field in the inlet with a correction to account for compressibility effects. The accuracy of the finite-element technique in predicting the acoustic properties of annular ducts has been checked by comparison with available analytical solutions for the problems of planeand spinning-wave propagation through a hard-walled annular duct with a constant mean flow. Results are presented comparing low-frequency plane-wave propagation through a hard-walled turbofan inlet containing a one-dimensional flow with the same inlet containing a fully two-dimensional axisymmetric mean flow. It is shown that when one-dimensional mean flow is assumed to exist in the duct, the plane wave propagates with relatively little distortion. However, propagation of a plane wave through the fully two-dimensional flow field in the inlet produces severe distortion due to the excitation of higher-order modes.

Sigman, R. K.↗
NASA NTRS1978

Design of an air ejector for boundary-layer bleed of an acoustically treated turbofan engine inlet during ground testing

An air ejector was designed and built to remove the boundary-layer air from the inlet a turbofan engine during an acoustic ground test program. This report describes; (1) how the ejector was sized; (2) how the ejector performed; and (3) the performance of a scale model ejector built and tested to verify the design. With proper acoustic insulation, the ejector was effective in reducing boundary layer thickness in the inlet of the turbofan engine while obtaining the desired acoustic test conditions.

Stakolich, E. G.↗
NASA NTRS1978

Multivariable quadratic synthesis of an advanced turbofan engine controller

A digital controller for an advanced turbofan engine utilizing multivariate feedback is described. The theoretical background of locally linearized control synthesis is reviewed briefly. The application of linear quadratic regulator techniques to the practical control problem is presented. The design procedure has been applied to the F100 turbofan engine, and details of the structure of this system are explained. Selected results from simulations of the engine and controller are utilized to illustrate the operation of the system. It is shown that the general multivariable design procedure will produce practical and implementable controllers for modern, high-performance turbine engines.

Dehoff, R. L.↗
NASA NTRS1978

Design and verification of a turbofan swirl augmentor

The paper discusses the details of the design and verification testing of a full-scale turbofan 'swirl' augmentor at sea level and altitude. No flameholders are required in the swirl augmentor since the radial motion of the hot pilot gases and subsequent combustion products provides a continuous ignition front across the stream. Results of rig testing of this full-scale swirl augmentor on an F100 engine, which are very encouraging, and future development plans are presented. The results validate the application of the centrifugal-force swirling flow concept to a turbofan augmentor.

Egan, W. J., Jr.↗
NASA NTRS1979

Annular acoustic liners for turbofan engines

Computer Program (written in FORTRAN IV) for design annular acoustic liners for turbofan engines first estimates noise generated by turbofan engine, then permits methodical examination of alternative choices of noise reduction.

Minner, G. L.↗
NASA NTRS1979

Combined pressure and temperature distortion effects on internal flow of a turbofan engine

An additional data base for improving and verifying a computer simulation developed by an engine manufacturer was obtained. The multisegment parallel compressor simulation was designed to predict the effects of steady-state circumferential inlet total-pressure and total-temperature distortions on the flows into and through a turbofan compression system. It also predicts the degree of distortion that will result in surge of the compressor. The effect of combined 180 deg square-wave distortion patterns of total pressure and total temperature in various relative positions is reported. The observed effects of the combined distortion on a unitary bypass ratio turbofan engine are presented in terms of total and static pressure profiles and total temperature profiles at stations ahead of the inlet guide vanes as well as through the fan-compressor system. These observed profiles are compared with those predicted by the complex multisegment model. The effects of relative position of the two components comprising the combined distortion on the degree resulting in surge are discussed. Certain relative positions required less combined distortion than either a temperature or pressure distortion by itself.

Braithwaite, W. M.↗
NASA NTRS1979

Analytical evaluation of the impact of broad specification fuels on high bypass turbofan engine combustors

Six conceptual combustor designs for the CF6-50 high bypass turbofan engine and six conceptual combustor designs for the NASA/GE E3 high bypass turbofan engine were analyzed to provide an assessment of the major problems anticipated in using broad specification fuels in these aircraft engine combustion systems. Each of the conceptual combustor designs, which are representative of both state-of-the-art and advanced state-of-the-art combustion systems, was analyzed to estimate combustor performance, durability, and pollutant emissions when using commercial Jet A aviation fuel and when using experimental referee board specification fuel. Results indicate that lean burning, low emissions double annular combustor concepts can accommodate a wide range of fuel properties without a serious deterioration of performance or durability. However, rich burning, single annular concepts would be less tolerant to a relaxation of fuel properties. As the fuel specifications are relaxed, autoignition delay time becomes much smaller which presents a serious design and development problem for premixing-prevaporizing combustion system concepts.

Taylor, J. R.↗
NASA NTRS1980

A measurement of forward-flight effects on the noise from a JT15D-1 turbofan engine in the NASA-Ames 40- by 80-Foot Wind Tunnel

A Pratt and Whitney JT15D-1 turbofan engine was tested in two facilities at Ames Research Center: the outdoor Static Test Facility and the 40- by 80-Foot Wind Tunnel. The primary purposes of the test were to determine the effects of forward velocity on the turbofan spectra in the forward quadrant for the cruise inlet and to compare these wind-tunnel spectra with outdoor spectra to determine the possibility of simulating forward-velocity effects from purely outdoor measurements. The wind-tunnel data show a reduction in the blade-passage frequency tones of the order of 10 dB with increasing forward velocity at subsonic fan-tip speeds. No forward-velocity variation was observed at supersonic tip speeds. Comparison of in-duct spectra for the cruise inlet at forward velocity, with spectra from outdoor tests with a distortion-control inlet shows excellent agreement for the in-duct data when allowance is made for different in-duct volumes. This is also reflected in good agreement for the far-field spectra at small forward angles. The comparisons of wind-tunnel and outdoor data also indicate that at least for the JT15D-1, it may be possible to approximate the shape of the far-field spectra at large directivity angles from an outdoor measurement with the cruise inlet, providing an effective inflow control device is used.

Ahtye, W. F.↗
NASA NTRS1980

Design and evaluation of an integrated Quiet, Clean General Aviation Turbofan (QCGAT) engine and aircraft propulsion system

The design was based on the LTS-101 engine family for the core engine. A high bypass fan design (BPR=9.4) was incorporated to provide reduced fuel consumption for the design mission. All acoustic and pollutant emissions goals were achieved. A discussion of the preliminary design of a business jet suitable for the developed propulsion system is included. It is concluded that large engine technology can be successfully applied to small turbofans, and noise or pollutant levels need not be constraints for the design of future small general aviation turbofan engines.

German, J.↗