Search NASA⌕ Search

SEARCH · Search NASA

Results for “viscous liquid”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Thermal Analysis of Axially Grooved Heat Pipes

The liquid viscous drag and the evaporator film coefficient were determined analytically for a heat pipe with axial rectangular grooves under zero-g conditions. The liquid pressure drop and the evaporator film coefficient for an axially grooved heat pipe were found to be expressed by the functions of the meniscus angle, which makes it possible to predict its performance analytically. The performance near its capillary pumping limit is influenced by the contact angle.

Kamotani, Y.↗

Forced Oscillations of Supported Drops

Oscillations of supported liquid drops are the subject of wide scientific interest, with applications in areas as diverse as liquid-liquid extraction, synthesis of ceramic powders, growing of pure crystals in low gravity, and measurement of dynamic surface tension. In this research, axisymmetric forced oscillations of arbitrary amplitude of viscous liquid drops of fixed volume which are pendant from or sessile on a rod with a fixed or moving contact line and surrounded by an inviscid ambient gas are induced by moving the rod in the vertical direction sinusiodally in time. In this paper, a preliminary report is made on the computational analysis of the oscillations of supported drops that have 'clean' interfaces and whose contact lines remain fixed throughout their motions. The relative importance of forcing to damping can be increased by either increasing the amplitude of rod motion A or Reynolds number Re. It is shown that as the ratio of forcing to damping rises, for drops starting from an initial rest state a sharp increase in deformation can occur when they are forced to oscillate in the vicinity of their resonance frequencies, indicating the incipience of hysteresis. However, it is also shown that the existence of a second stable limit cycle and the occurrence of hysteresis can be observed if the drop is subjected to a so-called frequency sweep, where the forcing frequency is first increased and then decreased over a suitable range. Because the change in drop deformation response is abrupt in the vicinity of the forcing frequencies where hysteresis occurs, it should be possible to exploit the phenomenon to accurately measure the viscosity and surface tension of the drop liquid.

Wilkes, Edward D.↗

Surface Collisions Involving Particles and Moisture (SCIP'M)

Experiments were performed on the collision of a solid sphere with a nearly horizontal flat surface covered with a thin layer of viscous liquid. High-speed collisions were obtained by dropping the ball onto the surface from various heights, using gravitational acceleration. Low-speed collisions were obtained using pendulums with long strings or by launching the balls at low velocities in the reduced-gravity environment of parabolic flight. The sphere bounces only when the impact velocity exceeds a critical value. The coefficient of restitution (ratio of rebound velocity to impact velocity) increases with increasing impact velocity above the critical value, indicating the increasing relative importance of elastic deformation to viscous dissipation. The critical impact velocity increases, and the coefficient of restitution decreases, with increasing viscosity or thickness of the liquid layer and with decreasing density or size of the sphere. The ratio of the wet and dry coefficients is expressed as a function of the Stokes number (ratio of particle inertia and viscous forces), showing good agreement between theory and experiment. Similar experiments were performed with the flat surface inclined at various angles to the approaching sphere. A modified Stokes number, which is a measure of the ratio of inertia of the sphere in the normal direction to the viscous forces exerted by the fluid layer, was used for the analysis of oblique collisions. Even for these oblique collisions, it was found that no rebound of the ball was observed below a certain critical Stokes number. The coefficient of normal restitution, defined as a ratio of normal rebound velocity to normal approach velocity, was found to increase beyond the critical Stokes number and even out as it approaches the value for dry restitution at high Stokes numbers. It was also found that, for smooth spheres like steel, the normal restitution at the same modified Stokes number is independent of the angle of impact. The tangential coefficient of restitution, defined as the ratio of tangential rebound velocity to tangential approach velocity, is found to be nearly unity, except for very low approach velocities. Thus, as a first approximation, the theories that predict the coefficient of restitution for head-on wet collisions can be extended to predict the coefficient of normal restitution for oblique wet collisions. Additional experiments were performed with soft surfaces in which a porous cloth or sponge layer was placed over the hard, flat surface. In these experiments, the coefficient of restitution was found to decrease with increasing impact velocity, due to inelastic losses in the soft material. A model combining inelastic deformation and flow through porous media was developed to describe these findings.

Davis, Robert H.↗

Fundamental Processes of Atomization in Fluid-Fluid Flows

This report outlines the major results of the grant "Fundamental Processes of Atomization in Fluid-Fluid Flows." These include: 1) the demonstration that atomization in liquid/liquid shear flow is driven by a viscous shear instability that triggers the formation of a long thin sheet; 2) discovery of a new mode of interfacial instability for oscillatory two-layer systems whereby a mode that originates within the less viscous liquid phase causes interfacial deformation as the oscillation proceeds; 3) the demonstration that rivulet formation from gravity front occurs because the local front shape specified by gravity and surface tension changes from a nose to a wedge geometry, thus triggering a large increase in viscous resistance; and 4) extension of the studies on nonlinear wave evolution on falling films and in stratified flow, particularly the evolution towards large-amplitude solitary waves that tend to generate drops.

McCready, M. J.↗

Geometry of thin liquid sheet flows

Incompresible, thin sheet flows have been of research interest for many years. Those studies were mainly concerned with the stability of the flow in a surrounding gas. Squire was the first to carry out a linear, invicid stability analysis of sheet flow in air and compare the results with experiment. Dombrowski and Fraser did an experimental study of the disintegration of sheet flows using several viscous liquids. They also detected the formulation of holes in their sheet flows. Hagerty and Shea carried out an inviscid stability analysis and calculated growth rates with experimental values. They compared their calculated growth rates with experimental values. Taylor studied extensively the stability of thin liquid sheets both theoretically and experimentally. He showed that thin sheets in a vacuum are stable. Brown experimentally investigated thin liquid sheet flows as a method of application of thin films. Clark and Dumbrowski carried out second-order stability analysis for invicid sheet flows. Lin introduced viscosity into the linear stability analysis of thin sheet flows in a vacuum. Mansour and Chigier conducted an experimental study of the breakup of a sheet flow surrounded by high-speed air. Lin et al. did a linear stability analysis that included viscosity and a surrounding gas. Rangel and Sirignano carried out both a linear and nonlinear invisid stability analysis that applies for any density ratio between the sheet liquid and the surrounding gas. Now there is renewed interest in sheet flows because of their possible application as low mass radiating surfaces. The objective of this study is to investigate the fluid dynamics of sheet flows that are of interest for a space radiator system. Analytical expressions that govern the sheet geometry are compared with experimental results. Since a space radiator will operate in a vacuum, the analysis does not include any drag force on the sheet flow.

Chubb, Donald L.↗

Inorganic chemistry: Direct syntheses from pure liquid SO3 and from trivalent and pentavalent nitrogen derivatives

From pure liquid SO3 direct synthesis reactions were carried out with N2O5, NO2Cl, NOCl which yielded N2O54SO3, 3SO3, 2SO3-NO2Cl2SO3-NOCl2SO3 and NOCl2SO3, the latter being obtained for the first time in the pure state. In all cases the crystallized product was obtained by separating the constituents of the mixture and then going through a single viscous liquid phase.

Vandorpe, B.↗

Rippling Instability of a Collapsing Bubble

The rippling instability of a liquid sheet was first observed by Debregeas, de Gennes, an Brochard-Wyart [Science 279, 1704 (1998)] on a hemispherical bubble resting on a free surface. Unlike a soap bubble, it collapses under its own weight while bursting, and folds into a wavy structure which breaks the original axisymmetry. In fact, this effect occurs for both purely elastic and purely viscous (liquid) sheets, and an analogy can be made between the two mechanisms. We present a theory for the onset of the instability in both cases, in which the growth of the corrugation out of an inextensible initial condition is governed by the competition between gravitational and bending (shearing) forces. The instability occurs for a range of densities, stiffnesses (viscosities), and sizes, a result which arises less from dynamics than from geometry, suggesting a wide validity. We further obtain a quantitative expression for the number of ripples. Finally, we present the results of experiments, which are consistent with our predictions.

daSilveira, Rava↗

Infrared Spectroscopy as a Chemical Fingerprinting Tool

Infrared (IR) spectroscopy is a powerful analytical tool in the chemical fingerprinting of materials. The technique is rapid, reproducible and usually non-invasive. With the appropriate accessories, the technique can be used to examine samples in either a solid, liquid or gas phase. Solid samples of varying sizes and shapes may be used, and with the addition of microscopic IR (microspectroscopy) capabilities, minute materials such as single fibers and threads may be examined. With the addition of appropriate software, microspectroscopy can be used for automated discrete point or compositional surface area mapping, with the latter providing a means to record changes in the chemical composition of a material surface over a defined area. Both aqueous and non-aqueous free-flowing solutions can be analyzed using appropriate IR techniques, as can viscous liquids such as heavy oils and greases. Due to the ability to characterize gaseous samples, IR spectroscopy can also be coupled with thermal processes such as thermogravimetric (TG) analyses to provide both thermal and chemical data in a single run. In this configuration, solids (or liquids) heated in a TG analyzer undergo decomposition, with the evolving gases directed into the IR spectrometer. Thus, information is provided on the thermal properties of a material and the order in which its chemical constituents are broken down during incremental heating. Specific examples of these varied applications will be cited, with data interpretation and method limitations further discussed.

Huff, Tim↗

Viscous-pendulum damper suppresses structural vibrations

The viscous pendulum damper consists of a cylinder containing round trays on which round lead slugs rest. When assembled, the container is filled with a viscous liquid and attached, with axis vertical, to the structure. The device permits varying the damping of structural vibrations.

Reed, W. H., III↗

Extended hydrodynamic theory of the peak and minimum pool boiling heat fluxes

The hydrodynamic theory of the extreme pool boiling heat fluxes is expanded to embrace a variety of problems that have not previously been analyzed. These problems include the prediction of the peak heat flux on a variety of finite heaters, the influence of viscosity on the Taylor and Helmoltz instability mechanisms with application to film boiling and to the peak heat flux in viscous liquids, the formalization of the analogy between high-current-density electrolysis and boiling, and the description of boiling in the low-gravity limit. The predictions are verified with a large number of new data.

Linehard, J. H.↗

Study of polyphenyl ether fluid /5P4E/ in operating elastohydrodynamic contacts by infrared emission spectroscopy

Infrared emission spectra of 5P4E polyphenyl ether were obtained from an operating elastohydrodynamic sliding contact at different speeds and loads by Fourier emission microspectrophotometry. The spectra were found to be polarized with respect to the direction of the conjunction line, especially at high shear rates. Film and metal surface temperatures were calculated from the spectra, and film thicknesses were determined under various operating conditions. Changes of polarized band structure above a critical shear rate, at which the slope of the film temperature versus shear curve changes abruptly and at which the film thickness assumes a minimum value, are consistent with a transition of the lubricant from a viscous liquid to a viscoelastic liquid or to an elastic solid.

Lauer, J. L.↗

Convective flows of viscous fluid in spherical layers. Certain astrophysical applications

The convective stability of a viscous liquid in spherical layers is investigated taking into consideration rotation, the latitudinal temperature gradient, and shear flow. The results of calculating nonlinear convective motion in spherical layers are examined. A discussion is given of the applicability of the results obtained to studying convection in astrophysical objects.

Yavorskaya, I. M.↗

Gas-Jet Levitation Furnace

Gas jet levitates solid and viscous liquid spheroids at high temperatures in new contactless processing system. System can be used to observe high temperature transformations (for example, crystallization without contact with another solid surface) or in containerless studies to eliminate contamination by crucible.

Ethridge, E. C.↗

Measurement of diffusion coefficients from solution rates of bubbles

The rate of solution of a stationary bubble is limited by the diffusion of dissolved gas molecules away from the bubble surface. Diffusion coefficients computed from measured rates of solution give mean values higher than accepted literature values, with standard errors as high as 10% for a single observation. Better accuracy is achieved with sparingly soluble gases, small bubbles, and highly viscous liquids. Accuracy correlates with the Grashof number, indicating that free convection is the major source of error. Accuracy should, therefore, be greatly increased in a gravity-free environment. The fact that the bubble will need no support is an additional important advantage of Spacelab for this measurement.

Krieger, I. M.↗

Vortices, stability, and turbulence

The transition process between laminar flow to turbulent flow is discussed in terms of a third state of fluid motion, vortical motion that is approximately periodic in space and/or time and displays symmetrical properties. The possibility that the transition from laminar to turbulent flow is accompanied by intermediate vortical states, with turbulence being an instability of the vortical states, is examined, with consideration given to the hypothesis that the turbulent state retains a memory of the vortex structures. Solutions are sought for the Navier-Stokes equations for a viscous liquid in a channel. Instances of inviscid vortical states and the presence of a three-dimensional instability are studied, demonstrating that transition phenomena can be explained qualitatively in terms of vortical state characteristics.

Saffman, P. G.↗

Improved Coulomb-Friction Damper

Equal damping provided on forward and reverse strokes. Improved damper has springs and wedge rings symmetrically placed on both ends of piston wedge, so friction force same in both directions of travel. Unlike conventional automotive shock absorbers, they resemble on outside, both versions require no viscous liquid and operate over wide temperature range.

Campbell, G. E.↗

Shape instability in thin viscous films and jets

The theory of viscous liquid films and thin jets as two- and one-dimensional continua is examined. Theoretical results are presented concerning a special type of instability which leads to the loss of smoothness of the shape (wrinkling) and associated with the failure of hyperbolicity of the governing equations. The conditions for different types of such an instability are formulated in the closed analytical form.

Zak, M.↗

Undercooling, Remelting, and Coarsening

Solidification of metal alloys with initial high undercoolings occurs with rapid recalescence due to rapid heat release of the latent heat of fusion. The recalescence temperature is usually higher than the solidus and/or the thermodynamic T sub o temperature of the alloy, depending on the initial undercooling and alloy composition. The rapid heating during recalescence alters the initially solidified structures, in ways that must include partial remelting, ripening, coarsening, and decomposition of the rapidly solidified primary metastable or supersaturated phases. New ways to study the solidification and remelting phenomena associated with the rapid heating during recalescence of undercooled alloys were developed. The phenomena are studied by using: (1) emulsions of iron and nickel base alloys in viscous liquid carriers; and (2) rapid heating of metal samples by electric discharge, using a technique similar to the exploding wire process (EWP), except with less power input. Experimental results are combined with theoretical analyses to better understand the solidification of levitated metal droplets with high undercooling, which relates to the solidification process.

Flemings, M. C.↗