Search NASA⌕ Search

SEARCH · Search NASA

Results for “void formation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

The interface in tungsten fiber reinforced niobium metal-matrix composites

The creep resistance of tungsten fiber reinforced niobium metal-matrix composites was evaluated. The interface region between the fiber and matrix was characterized by microhardness and electron probe microanalysis measurements which indicated that its properties were between those of fiber and matrix. However, the measured properties of the composite exceeded those calculated by the rule of mixtures even when the interface zone was assumed to retain all the strength of the fiber. The composite structure appeared to enhance the strengths of both the fibers and the matrix above what they exhibited in stand-alone tests. The effect of fiber orientation and matrix alloy composition on the fiber/matrix interface were also evaluated. Small alloying additions of zirconium and tungsten to the niobium matrix affected the creep resistance of the composites only slightly. A decrease in the creep resistance of the composite with increasing zirconium content in the matrix was ascribed to an increase in the diffusion rate of the fiber/matrix interdiffusion reaction, and a slight increase in the creep resistance of the composite was observed with an addition of 9 w percent tungsten to the matrix. In addition, Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis.

Grobstein, Toni L.↗
NASA NTRS1989

Creep behavior of tungsten fiber reinforced niobium metal matrix composites

Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared on a strength to density basis. The effect of fiber orientation on the creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.

Grobstein, T. L.↗
NASA NTRS1992

Creep behavior of tungsten fiber reinforced niobium metal matrix composites

Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.

Grobstein, Toni L.↗
DOE OSTI2024

Microstructural evolution in doped high entropy alloys NiCoFeCr-3X (X=Pd/Al/Cu) under irradiation

Commonly studied equatomic single-phase FCC high entropy alloys based on 3d transition metals like NiCoFeCr do not provide adequate strength and radiation resistance at high doses for nuclear structural applications. In the current study, the major alloying effects like lattice distortion, ordering and clustering tendencies were investigated by adding low concentration of Pd, Al, or Cu respectively to study the doping effects on the ion irradiation response of NiCoFeCr alloy. The alloys were irradiated with 3 MeV Ni 2+ ions at 500 °C to a fluence of 1 × 10 17 /cm 2 at a beam flux of approximately 2.8 × 10 12 ions/cm 2 /s. The microstructural evolution upon irradiation i.e., formation of dislocation networks, radiation induced segregation and precipitation, and void formation were studied in detail. Further, post-irradiation characterization results showed that a Pd addition leads to a high void nucleation rate but controlled void growth, which may be attributed to increased lattice distortion. In Al added HEA, our microstructural analysis indicates that radiation induced ordered L1 2 precipitates do not affect void swelling significantly. Cu addition led to Cu precipitation that drastically suppressed dislocation density and void swelling of the alloy. Additionally, a model was developed to qualitatively describe the trend in void swelling of typical FCC alloys under ion irradiation. This model was able to qualitatively explain the suppression and reappearance of void swelling in ion irradiated alloys that generally occurs near the region with peak implanted ion concentration.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Temperature and dose effects on dislocation loops in self-ion irradiated high-purity iron

Body-centered cubic (BCC) Fe-based alloys are promising candidate materials for advanced nuclear reactors. However, a detailed understanding of irradiation induced dislocation loop microstructure development remains unresolved. It is a widespread belief that 〈001〉 loops become increasingly favorable over ½〈111〉 loops as irradiation temperature rises above ∼300 C. Unfortunately, the temperature effects on 〈001〉 loop have been primarily examined in in-situ irradiation on TEM thin foils but poorly explored on bulk Fe due to exceedingly limited experimental studies on bulk specimens, raising concerns about the potential influence of TEM thin foil artifacts on observed results. Here, in this study, we conducted experiments on ultra-high purity BCC Fe specimens irradiated with 6.7–8 MeV Fe ions over a wide temperature range on bulk samples. We investigated the effects of temperature (T irr = 250–500 °C), dose rate (10⁻⁵ to 10⁻³ dpa/s), and dose (0.35 to 3.5 dpa) on the formation and evolution of 〈001〉 and ½〈111〉 loops as well as cavity (void) formation. Post-irradiation Burgers vector analysis via g•b method on dislocation segments and loops revealed that 〈001〉 loop fraction does not show a monotonic positive correlation with irradiation temperature. Combined with previous and current theoretical as well as experimental findings, we explore the temperature effects on all existing models of 〈001〉 loop formation. We conclude that the prevailing reports regarding the dominance of 〈001〉 loops in Fe at elevated temperatures are mainly attributable to the loss of glissile ½〈111〉 clusters in TEM thin foil experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Heat Transfer in Void Generating Foam Decomposition: Further Development

Continued development of the additive conductivity material model, used to simulate changes in heat transfer that occurs in void generating foam decomposition, has resulted in an improved model and new features. The previous version of the model was calibrated against the Aria Bulk Fluid Element (BFE) solution and proposed a third-order polynomial correction term best captured the increased heat transfer due to voids in the foam. An investigation of the Fuego Conjugate Heat Transfer (CHT) and Aria BFE solutions at several geometries revealed the CHT solution and BFE solution had differing behavior across length scales, especially at smaller scales. Five calibration studies, using the Fuego CHT as the calibration data, were carried out with polynomial functions of 4-th, 3-rd, 2-nd, 1-st and 0-th orders to determine the best correction function that generalized well across length scales. Each polynomial function was calibrated/trained on six different sized geometries and then tested on three uniquely sized geometries. This study revealed that the 1-st order additive conductivity model performed the best. A new feature of void formation scaling was implemented to more realistically capture the heat transfer as voids are created. A scaling term was added to the model to activate the conductivity correction as decomposition progresses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

In-situ and ex-situ characterization of irradiated AM materials

This study investigates the irradiation performance of laser powder bed fusion (LPBF) 316L and 316H stainless steels (SS), and their wrought counterparts. While LPBF 316L has been more studied, LPBF 316H is relatively new, with little prior data on its irradiation behavior. The research involved fabricating, preparing, irradiating, and characterizing six materials: LPBF 316L (two variants), LPBF 316H (two variants), and wrought 316L and 316H. LPBF materials were subjected to various heat treatments, including solution annealing and stress relief, and were irradiated using in-situ and ex-situ ion techniques at temperatures of 300°C and 600°C, with doses ranging from 0.2 dpa to 25 dpa. Under ex-situ irradiation with 4 MeV Ni 2+ ions at 600°C, the dislocation cell structures in LPBF316L-1 and LPBF316H-1 gradually evolved into a uniform dislocation network. At a low irradiation dose (0.2 dpa), the cell structures were still partially visible. At 2 dpa, a uniform dislocation network formed, though remnants of the original cell structure were still discernible as contrast domains. At 5 dpa and 10 dpa, even the contrast domains vanished. For irradiation at 300°C, the cell structure was still clearly visible at 0.2 dpa for LPBF316L-1. For LPBF316H-1, the dislocation cell structure was less apparent at the same dose but was still recognizable. With further increase in dose at 300°C, the dislocation cell walls were completely replaced by irradiation-induced defects and no longer visible. Void formation was observed for irradiation at 600°C. At 2 dpa, no evident voids were observed in either LPBF316L-1 or LPBF316H-1.

36 MATERIALS SCIENCE↗
NASA NTRS2019

Computational Materials Techniques for Thermal Protection Solutions: Materials and Process Design

Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 K) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

thermal protection↗
NASA NTRS2019

Computational Materials Techniques for Thermal Protection Solutions: Materials and Process Design

Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 degrees Kelvin) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

Thermal Protection↗
NASA NTRS2018

Computational Materials Techniques for Thermal Protection Solutions: Materials and Process Design

Integrated computational materials techniques that span the atomistic and continuum scales have the potential to aid the design and manufacturing of thermal protection materials. Two cases demonstrating the practical application of these methods are discussed. Case one examines the selection of a high temperature coating for carbon/carbon, with the target application being a solar thermal propulsion heat exchanger. The performance of various refractory metal and metal-carbide coatings is characterized considering extreme thermal (3500 K) and chemical (hydrogen flows) conditions. The recession rate, hydrogen leakage, and likelihood of mechanical failure are characterized and provide directions for further experimental investigation. Case two examines the process optimization of a heat shield material composed of a woven silica fiber preform and cyanate ester resin. Frequently, internal voids were found to be present in this composite after the resin infusion and curing stages of manufacturing. Using the manufacturing conditions, computations indicate that both water adsorption and resin cure shrinkage are contributing factors to void formation. The results suggest an alternative process configuration for curing that would mitigate voids.

Haskins, Justin↗
DOE OSTI2025

AMMT 2025 Milestone

Idaho National Laboratory initiated the examination of nickel-based alloys manufactured laser powder directed energy deposition additive manufacturing for potential applications in nuclear, high temperature structural components. With the rapid push towards additive manufacturing, codes do not exist that definitively define what is or is not tolerable for each process and application, such as with conventional, wrought products. This report contains the initial work to understand possible manufacturing methods for high temperature alloys, and specifically, void formation, microstructure evolution, and mechanical properties. To generate mechanical test data, specimens were tested irrespective of voids and microstructures were analyzed to better understand how to negate/improve these issues. The preliminary results showed major decreases in mechanical performance for material tested. Test specimens will continue to be produced to further improve additive manufacturing processes, quantify void acceptance, and better understand the most suitable high temperature alloys receptive to additive manufacturing and high temperature nuclear applications.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Unraveling the size fluctuation and shrinkage of nanovoids during in situ radiation of Cu by automatic pattern recognition and phase field simulation

Void formation is an important aspect of irradiation response of metals. In situ transmission electron microscopy observation for void evolution during irradiation is an effective technique for studying void evolution. However, the amount of data collected during in situ studies drastically overwhelm the current capability for manual data analyses. Here, we used a data-driven approach where a convolutional neural network combined with greedy matching to detect and track nanovoid evolutions and migrations. This approach was able to discover the surprising phenomena of void size fluctuation and shrinkage during irradiation of Cu with pre-existing nanovoids. Phase–field simulations revealed the fundamental mechanism behind this in situ observed phenomenon of void size fluctuation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Nuclear Structural Component Relevant Properties of Nickel-Based Alloys Produced via Additive Manufacturing

Idaho National Laboratory initiated examination of nickel-based alloys manufactured via three different additive manufacturing methods for potential applications in nuclear, high temperature structural components. The three methods analyzed included laser powder bed fusion, blown powder laser directed energy deposition, and wire-fed gas metal arc directed energy deposition. With the rapid push towards additive manufacturing, codes do not exist that definitively define what is or is not tolerable for each process and application, such as with conventional, wrought products. This report contains the initial work to understand possible manufacturing methods for high temperature alloys, and specifically, void formation, microstructure evolution, corrosion, and mechanical properties. To generate mechanical test data, specimens were tested irrespective of voids and microstructures were analyzed to better understand how to negate/improve these issues. The preliminary results showed major decreases in mechanical performance for material tested. Test specimens will continue to be produced to further improve each additive manufacturing processes, quantify void acceptance, and better understand the most suitable high temperature alloys receptive to additive manufacturing and high temperature nuclear applications.

36 MATERIALS SCIENCE↗
NASA NTRS2001

Formation of Residual Gases from Source Materials in Closed Crystal Growth Systems

Different, non-constituent cases are present in crystal growth systems and may affect processes like growth rate in PVT or voids formation and detached solidification in melt growth systems. The presence of the gas may be detrimental or advantageous depending on its amount and composition, and on the process in question. The presence of the cases, their amount and composition, can be caused and changed by diffusion through and desorption from the growth container material. We have investigated these phenomena for silica glass ampoules. We also found, that residual cases can be generated by the source materials: even very high purity commercial elements and compounds may contain trace amounts of impurities, particularly oxides. The oxides may have low volatilities themselves but their reaction with other species, particularly carbon and hydrogen, may produce volatile compounds like water or carbon oxides. The amount of the gas and its composition is dependent on the original purity of the material (oxide contaminants) and the heat treatment of the source prior to sealing. In many cases. particularly at temperatures below about 900 C and in well-outgassed ampoules, this mechanism dominates. The problem is of a particular importance in sealed systems where the amount and composition of the gas cannot be directly controlled. Therefore, a reasonable knowledge and understanding of the origin, composition, magnitude, and change with time of gases present in sealed ampoules may be important for a meaningful control and interpretation of crystal growth processes. We have investigated this phenomenon in more details for a number of elements and compounds, primarily for II-VI and IV-VI materials. Different source pre-treatment and annealing procedures were applied, and subsequent consecutive annealings and measurements were done to determine the origin and development of the gas in the systems.

Palosz, W.↗
DOE OSTI2020

From suppressed void growth to significant void swelling in NiCoFeCr complex concentrated solid-solution alloy

Void swelling can result in dimensional instability and undermine the safe operation of nuclear reactors. Current strategies to inhibit void swelling mainly focus on enhancing defect absorption and recombination by introducing high-density defect sinks. Complex concentrated solid-solution alloys (CSAs), including high-entropy alloys, can withstand severe radiation damage due to their inherent chemical complexity without interfaces. However, the underlying mechanisms for void suppression in CSAs are far from clear. In this research, we studied the void evolution with respect to irradiation depths, doses, and temperatures in equiatomic NiCoFeCr under 3 MeV Ni ion irradiations. At relatively low doses (16 and 54 displacements per atom, dpa), voids form mainly outside of the ion-damaged region, and void formation in the peak damage region is suppressed, leading to negligible swelling. However, with further increase of dose (86 up to 250 dpa), significant void growth occurs in the peak damage region and extended dislocation lines dominate instead of short dislocation lines and loops formed at lower doses. From 500 to 700 °C, the dislocation density decreases while dislocations grow. Although the overall void swelling increases dramatically from 500 to 580 °C at 54 dpa, void growth in the peak damage region is still suppressed. The transition from suppressed void growth to significant void swelling is attributed to dislocation evolution and local chemical inhomogeneity (enrichment of Fe/Cr in the matrix) at higher doses. Our study shows that controlling element diffusion and defect evolution through tuning chemical complexity can further enhance the swelling resistance of CSAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The effect of aspect ratio on the mechanical behavior of Li metal in solid-state cells

The Li metal anode is necessary for solid-state batteries to dramatically exceed the energy density of state-of-the-art conventional Li-ion batteries. To enable the Li metal anode, the mechanical properties of Li metal under compression in a commercially relevant cell configuration must be determined. This work examines the compression creep behavior of Li metal coupled with a relevant model solid-state electrolyte (Li 6.5 La 3 Ta 0.5 Zr 1.5 O 12 ) and current collector (Ni) as a function of applied stress (1–10 MPa) and Li foil thickness (100–700 μm). At 1 MPa applied stress, the strain rate of all Li foil thicknesses under compression was almost four orders of magnitude lower than what is predicted from tensile creep tests. Steady-state creep behavior was observed for Li foil ≥350 μm at 5 MPa and ≥250 μm at 10 MPa. Conversely, sustained creep deformation was not observed for 100 and 150 μm Li foils at any applied stress. It is suggested that friction at the Li/LLZO and Li/Ni interfaces leads to the formation of hydrostatic stress that controls Li deformation at low aspect ratios. Finally, these results have implications for battery pack stack pressure requirements, particularly relating to void formation during stripping and Li metal filament penetration during plating.

25 ENERGY STORAGE↗
DOE OSTI2023

Surface Film Formation on Al-V Alloys with Far-From-Equilibrium Microstructure

Nanocrystalline supersaturated Al-V alloys produced by high-energy ball milling have been reported to exhibit enhanced corrosion resistance and mechanical properties compared to commercial Al alloys. Corrosion of passive alloys such as Al-V alloy relies on the characteristics of the surface film, which is studied using scanning/transmission electron microscopy and time-of-flight secondary ion mass spectrometry. The effect of microstructure and composition on the surface film has been investigated after different immersion periods (30 min, 2 h, and 1 day) in 0.1 M NaCl. The surface film was complex and composed of oxidized Al and V. The heterogeneous surface film was observed due to the presence of secondary phases and initiation of localized corrosion. The void formation was observed beneath the surface film that would potentially cause pitting corrosion. The generation of nano-sized voids was dependent on grain orientation. Compared to pure Al, the chloride penetration is suppressed in Al-V alloys. The effect of composition and microstructure on surface film formation and attendant corrosion behavior is discussed herein.

36 MATERIALS SCIENCE↗