Aquaporin-7: A Dynamic Aquaglyceroporin With Greater Water and Glycerol Permeability Than Its Bacterial Homolog GlpF
Not Available
59 BASIC BIOLOGICAL SCIENCES↗
SEARCH · Search NASA
Results for “water permeability”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Data From: Simulating bioclogging effects on dynamic riverbed permeability and infiltration, Water Resources Research
We collected a time series of Russian River infiltration rates to parameterize stochastic model development of infiltration conditions as a function of bioclogging. The time series of infiltration were collected from the Russian River Riverbank Filtration site located in Sonoma County California. Infiltration datasets are shown in units of m/day and were obtained using a seepage meter in 2012. To address the combined effects of bioclogging and disconnection on infiltration, we developed numerical representations of bioclogging processes based on these datasets using a within a one-dimensional, variably saturated flow model representing losing-connected and losing-disconnected rivers. All models and bioclogging formulations were used to create synthetic test cases for bioclogging.This research was supported by the Jane Lewis Fellowship from the University of California, Berkeley, the Sonoma County Water Agency (SCWA), the Roy G. Post Foundation Scholarship, the U.S. Department of Energy, Office of Science Graduate Student Research (SCGSR) Program, U.S. Department of Energy, Office of Science, Office of Biological and Environmental Research under award DE-AC02-05CH11231, and the UFZ-Helmholtz Centre for Environmental Research, Leipzig, Germany.
54 ENVIRONMENTAL SCIENCES↗
Hydrate is a Nonwetting Phase in Porous Media
In porous media containing gas hydrate, the hydrate morphology impacts the flow behavior of the fluid phases. We hypothesize that hydrate emplaces itself as a nonwetting phase and use this idea to describe relative permeability of water in a hydrate/water system. We perform steady-state relative permeability measurements in hydrate-bearing samples with a range of hydrate saturation. We measure and compare water relative permeability in the presence of gas and in the presence of hydrate and find that the water relative permeability is the same in both cases. This suggests that (1) relative permeability for hydrate systems can be obtained without performing difficult experiments on hydrate bearing sediments, (2) flow properties are porous-media dependent, and (3) models that assume a fixed pore or tube geometry are inadequate.
58 GEOSCIENCES↗
Dispersion of high oxygen permeability ionomers in water-propanol solutions
There is a growing interest in high oxygen permeability ionomers (HOPI) for better-performing proton exchange membrane fuel cell (PEMFC) catalyst layers. In this study, we used small-angle x-ray scattering (SAXS) to analyze dispersions of two types of perfluorinated sulfonic acid (PFSA) ionomers and a HOPI in water and propanol solvents, at concentrations between 1 wt% and 15 wt%. HOPI dispersions exhibited the interference peak typical of ionomers; by separately fitting the peak and higher- q regions with several models, we demonstrated that HOPI aggregates have a closer average spacing than conventional PFSA ionomers, and smaller aggregate size when assuming a cylindrical geometry. By measuring conventional PFSA ionomers with two side chain lengths and several equivalent weights, we showed that these side chain parameters alone did not explain the differences in aggregate spacing or size. In addition, the pattern was present whether samples were prepared in a 50/50 water/propanol or a more propanol-rich mixture. As such, the structural differences of HOPI could be due to its different backbone monomer. A better understanding of the influence of the HOPI chemistry on dispersion properties could help explain the ink structure and drying characteristics of HOPI observed in prior work. Future study of ionomer-catalyst mixtures, such as measuring ionomer adsorption to carbon, would help elucidate the role of ionomer from ink formulation to the cast electrode.
Aquivion↗
Pc to RP Method_water-wet
Capillary Pressure to Relative Permeability water-wet algorithm.
Capillary Pressure↗
Aqueous redox flow battery electrolytes with high chemical and electrochemical stability, high water solubility, low membrane permeability
The invention features redox flow batteries and compound useful therein as negolytes or posolytes. The batteries and compounds are advantageous in terms of being useable in water solutions at neutral pH and have extremely high capacity retention. Suitable negolytes are diquaternized bipyridines, suitable posolytes are water-soluble ferrocene derivatives.
Gordon, Roy G.↗
Challenge Solutions for a Significant Water Cut Reduction History Match on Heavy Oil Polymer EOR
Milne Point Field is conducting the first-ever active polymer flood pilot program designed to enhance oil recovery (EOR) of heavy oils on the Alaska North Slope (ANS). The experimental field program consists of two pairs of horizontal injection and production wells deployed in an isolated fault block in the Schrader Bluff reservoir. The EOR method combines polymer flooding and low salinity water flooding to improve recovery. Prior average water cut reduction in polymer EOR fields ordinarily ranges between 10% to 15% for most light oil and heavy oil reservoirs. When comparing other field applications, the long-lasting (24 months) and much lower water cut poses a challenge for numerical history matching when applying typical simulation methods. This abstract discusses two practical new approaches used for history matching of the long-lasting ultralow water cut. These new applications include 1) multiple relative permeability curves with J-function incorporation with low endpoints of relative permeability of water (Krw). This approach integrated the permeability differential adjustment in the geometries of horizontal and vertical directions based on geological review. 2) A specific permeability channel strips along with the horizontal or vertical planar assumption. The current history matching results indicate success in achieving an excellent agreement with the field observed low water-cut.
Namie, S.↗
Molecular insights into the structure-property relationships of 3D printed polyamide reverse-osmosis membrane for desalination
3D-printing is an emerging method for manufacturing polyamide (PA) reserve osmosis (RO) membranes for water treatment and desalination, which can precisely control membrane structural properties, such as thickness, roughness, and resolution. However, the synthesis-structure (i.e., degree of cross-linking (DC), m-phenylenediamine/trimesoyl chloride (MPD/TMC) ratio, and membrane thickness) to property (permeability and water-salt selectivity) relationships for these membranes has not been well understood. At the same time, a microscopic understanding of the physical mechanism of water and salt transport is needed to guide the design of high-performance 3D-printed membranes and improve the printing efficiency. Furthermore, the atomic-scale transport features and energetics of water and salt ions are studied at high pressure for the 3D-printed PA RO membranes with the different DCs and MPD/TMC ratios through non-equilibrium molecular dynamics (NEMD) simulations. Factoring in membrane structure properties, rejection ratio of salt ions and pressure-dependent water flux, 3D-printed PA membranes having an MPD/TMC ratio of 3.0:2.0 and a DC between 80%~90% attains ideal performance: high water flux, high rejection of salt ions, and excellent structural integrity. Mechanistically, water permeability for highly cross-linked PA RO membranes depends on the temporary on-and-off channels that allow water molecules to jump from one cavity to another at high pressure. In addition, higher pressures cause rapid compaction of PA membranes’ free volume and membrane thickness. Membrane failure at high pressure is determined by the DC and MPD/TMC ratios-dependent compressive yield strength. In short, these findings provide physical insights for optimizing existing PA membranes and designing next-generation desalination membranes at the molecular level.
3D-printed PA RO membrane↗
Prediction of moisture transfer in cement-based materials: Use of a porous network model to access transfer parameters
Knowing the water transport phenomena is fundamental for understanding the durability of cement-based materials. The moisture content within cementitious materials is of primary importance because it has a direct influence on mechanical (shrinkage, creep) and chemical (penetration of aggressive agents) degradation. Many models based on the determination of the transfer properties of the material under study already exist but require fitting of the parameters to find the experimental kinetics. Transfer parameters are generally estimated from the empirical approaches developed for soils by Van Genuchten and the water vapour diffusion reduction factor is often calculated via Millington's semi-empirical model. In this paper, we make a proposal to improve the prediction of moisture transfer, through mechanisms such as drying, capillary imbibition and water vapour permeability in cement-based materials, by using a porous network model to access the transfer parameters.
36 MATERIALS SCIENCE↗
Introduction to this special section: Geothermal energy
Geothermal energy is a global renewable resource that has the potential to provide a significant portion of baseload energy in many regions. In the United States, it has the potential to provide 8.5% of the electric generation capacity by the middle of the century. In general, geothermal systems require heat, permeability, and water to be viable for energy generation. However, with current technologies, only heat is strictly necessary in a native system. Engineered geothermal systems (EGS) introduce water into the subsurface at elevated pressures and reduced temperatures and enhance permeability through hydraulic and/or shear fracturing. Additionally, although moderate- to high-temperature resources currently dominate geothermal energy production, low-temperature resources have been utilized for direct-use cases. When well balanced and maintained, geothermal resources can produce significant amounts of heat and achieve long-term sustainability on the order of an estimated tens to hundreds of years.
15 GEOTHERMAL ENERGY↗
Characterization of wood fiber insulation for the development of wood fiber-insulated panels (WIPs) for use in building envelope
Wood fiber insulation (WFI) was studied as an eco-friendly alternative for fossil-based building insulation, focusing on its use in new wood fiber-insulated panels (WIPs). Rigid WFI boards with densities of 110, 140, and 180 kg/m³, including a 140 kg/m³ variant without paraffin wax, were evaluated. Key properties investigated included porosity, water vapor transmission, liquid water adsorption, and thermal conductivity. The porosity ranged between 85 and 92%, primarily influenced by density. Water vapor permeability ranged from 65 to 90 ng·s-1m-1Pa-1, while liquid water absorption was between 2.5 and 20% by volume, influenced by both wax and density. The thermal conductivity coefficient ranged from 0.038 to 0.055 W/(m·K). Bond strength tests with WFI (140 kg/m³ with wax) laminated to various materials using structural adhesives showed tensile perpendicular-to-grain strengths of 10 to 16 kPa and shear strengths of 60 to 90 kPa, with failure only occurring within the WFI. It was concluded that WFI is a promising material for novel WIPs, offering competitive hygrothermal properties and compatibility with structural adhesives. However, its bio-based nature suggests variability and complexity, necessitating further rigorous testing in various climates and in more complex assemblies.
Materials Science↗
Quantifying Drivers of Methane Hydrobiogeochemistry in a Tidal River Floodplain System
The influence of coastal ecosystems on global greenhouse gas (GHG) budgets and their response to increasing inundation and salinization remains poorly constrained. In this study, we have integrated an uncertainty quantification (UQ) and ensemble machine learning (ML) framework to identify and rank the most influential processes, properties, and conditions controlling methane behavior in a freshwater floodplain responding to recently restored seawater inundation. Our unique multivariate, multiyear, and multi-site dataset comprises tidal creek and floodplain porewater observations encompassing water level, salinity, pH, temperature, dissolved oxygen (DO), dissolved organic carbon (DOC), total dissolved nitrogen (TDN), partial pressure of carbon dioxide (pCO 2 ), nitrous oxide (pN 2 O), methane (pCH 4 ), and the stable isotopic composition of methane (δ 13 CH 4 ). Additionally, we incorporated topographical data, soil porosity, hydraulic conductivity, and water retention parameters for UQ analysis using a previously developed 3D variably saturated flow and transport floodplain model for a physical mechanistic understanding of factors influencing groundwater levels and salinity and, therefore, CH 4 . Principal component analysis revealed that groundwater level and salinity are the most significant predictors of overall biogeochemical variability. The ensemble ML models and UQ analyses identified DO, water level, salinity, and temperature as the most influential factors for porewater methane levels and indicated that approximately 80% of the total variability in hourly water levels and around 60% of the total variability in hourly salinity can be explained by permeability, creek water level, and two van Genuchten water retention function parameters: the air-entry suction parameter α and the pore size distribution parameter m. These findings provide insights on the physicochemical factors in methane behavior in coastal ecosystems and their representation in local- to global-scale Earth system models.
54 ENVIRONMENTAL SCIENCES↗
A Novel Relative Permeability Model for Gas and Water Flow in Hydrate-Bearing Sediments With Laboratory and Field-Scale Application
In a producing gas hydrate reservoir the effective porosity available for fluid flow constantly changes with dissociation of gas hydrate. Therefore, accurate prediction of relative permeability using legacy models (e.g. Brooks-Corey (B-C), van Genuchten, etc.) that were developed for conventional oil and gas reservoirs would require empirical parameters to be calibrated at various S h over its range of variation, but such calibrations are precluded because of lack of experimental relative permeability data. This study proposes a new relative permeability model for gas hydrate-bearing media that is a function of maximum capillary pressure, capillary entry pressure, pore size distribution index, residual saturations, hydrate saturation, and four other constants. The three novel features of the proposed model are: (i) requires fitting its six empirical parameters only once using experimental data from any single S h , and the same set of empirical parameters predict relative permeability at all S h , (ii) includes the effect of capillarity, and (iii) includes the effect of pore-size distribution. From practical standpoint, the model can be used to simulate multiphase flow in gas hydrate-bearing sediments where the proposed relative permeability can account for the evolving hydrate saturation. The proposed model is implemented in a numerical simulator and the wall time required to perform simulations using the proposed model is shown to be similar to the time it takes to run same simulations with the B-C model. The proposed model is a step forward towards achieving the goal of physically accurate modeling of multiphase flow for gas hydrate-bearing sediments that accounts for the effect of gas hydrate saturation change on relative permeability.
54 ENVIRONMENTAL SCIENCES↗
Separation of isoprene from biologically-derived gas streams
Renewable organic precursors, including olefinic compounds such as isoprene, have attracted interest from the polymer and pharmaceutical industries. Biologically-derived processes can generate these target compounds; however, their gaseous product streams are complex mixtures of condensable organic vapors (COVs), water vapor, carbon dioxide (CO 2 ), and/or nitrogen (N 2 ). Because COVs, CO 2 and water vapor are known to alter polymer membranes, mixed gas separations data at ambient and elevated temperatures are limited. Here, this study focused on two classes of polymer membranes, glassy [polyetherimide (Ultem®)] and a rubbery [polydimethylsiloxane (PDMS)] with results indicating that isoprene separation is possible in humidified gas environment (2–4 vol% water). Gas permeabilities of these membranes did not noticeably change in the presence of humidity; however, the selectivity of these membranes was significantly lower compared to their performance under dry conditions. The role of water vapor in gas transport was derived from the energy of activation of permeation (E p ) for PDMS and Ultem® from 30–80°C in humidified mixed gas streams. For both polymers, E p data shows a slight decrease in selectivity with the other gases (hydrogen, N 2 , CO 2 , and methane) at elevated temperatures in the presence of water vapor. Thus, these COVs separations are feasible with polymer membranes in the presence of humidified gas streams, even in the case of glassy and rubbery membranes in series.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Engineered Water for Improved Oil Recovery from Fractured Reservoirs (Final Scientific/Technical Report)
The goal of this proposal is to field test the novel technology of engineered water (modifying ionic composition and/or adding surfactants or nanoparticles) injection to improve oil recovery from the carbonate matrix in fractured reservoirs. Carbonate reservoirs tend to be oil-wet/mixed-wet due to positively charged carbonate mineral surfaces and negatively charged acidic/asphaltic components in the oil. Many carbonate reservoirs are also highly fractured. Water injection does not work efficiently in fractured oil-wet reservoirs because water does not imbibe into the matrix. The water composition can be engineered with ionic modification, surfactants and nanoparticles which can change the wettability of carbonate rocks towards more water-wet conditions which can imbibe water into the matrix and push the oil into the fractures. The engineered water can also lower interfacial tension and minimize capillary forces so that gravity can push the oil up and out of the matrix. Wettability alteration also increases water relative permeability which can also improve oil recovery in non-fractured carbonate reservoirs. This technology, if successful, can be a game changer for West Texas carbonates.
02 PETROLEUM↗
Effect of autogenous shrinkage on microcracking and mass transport properties of concrete containing supplementary cementitious materials
It is well-known that supplementary cementitious materials (SCMs) and low water-to-binder (w/b) ratio increase autogenous shrinkage, but the impact on microcracking and long-term transport properties is less understood. This paper examines the effect of microcracking induced by autogenous shrinkage on transport properties of concretes cured up to ~3.6 years. Variables include SCM type (9% SF, 70% GGBS), w/b ratio (0.20–0.45), maximum-aggregate-size (MSA: 5–20 mm) and shrinkage reducing admixture (SRA). Oxygen diffusivity, permeability and water sorptivity were correlated with microcracks characterised using laser scanning confocal microscopy and 3D X-ray microtomography. Results show greater microcracking in mixes containing SCMs, low w/b ratio and large MSA. At the same w/b ratio and binder type, strong positive correlations are observed between transport and microcracking with increasing MSA, confirming the negative impact of autogenous shrinkage. SRA was effective in reducing these effects. The significance is compared with drying shrinkage and implications for durability are discussed.
36 MATERIALS SCIENCE↗
Quantifying Properties for a Mechanistic, Predictive Understanding of Aqueous Impact on Aging of Medium and Low Voltage AC and DC Cabling in Nuclear Power Plants
To address the gap in knowledge in understanding degradation in relevant service conditions, this project aimed to develop a mechanistic, predictive model of medium and low voltage cable failure based on the primary environmental degradation parameters of aqueous immersion time, temperature, and the oxidation extent. To do so, we took a two-fold approach toward evaluating degradation as related to the aqueous condition. First, we evaluated the chemical, mechanical, and electrical properties of polymers that comprise the cabling insulation under varied aqueous conditions at different temperatures. Secondly, we evaluated the performance of insulation materials under similar accelerated aging conditions in addition to the dielectric breakdown of the cabling under submersion conditions. Thermal oxidation and immersion of LDPE thin films were done using a Parr vessel and the extent of oxidation was monitored using the carbonyl index from ATR-FTIR spectrum, a ratio quantifying the carbonyl functionality produced on the LDPE film surface. Increasing the temperature, oxidation time, and oxygen pressure increased the water-vapor permeability and the carbonyl content. Thermogravimetric analysis of the films confirmed that there is indeed an initial weight loss of the smaller molecular weight molecules and volatiles. At higher temperatures, there is a secondary mass loss. Up to 70°C, the mass loss curves were similar until 80°C, when the aged films decreased at a much greater rate with respect to increasing temperature. This was seen in the 10, 50, 90% weight loss temperatures. The mechanical properties of sheet PP and HDPE as well as injection molded LDPE, HDPE, HDPP dog bones were plotted with respect to the time spent in the Parr vessel during thermal oxidation. For the sheet PP and HDPE, the UTS and the modulus of elasticity decreased while the elongation increased. The injection-molded LDPE, HDPE, and HDPP dog bones experienced a similar trend where the changes in the properties were within experimental uncertainty. This analysis of LDPE in dry and immersive oxygen-rich environments is an important baseline for future experiments looking at other degradation mechanisms. A predictive aging model for low-density polyethylene insulative cable housings was developed. This model revealed a combination of physical and chemical processes which lead to an increase in permeability and a decrease in strength of the insulator. In creating this predictive model, a gap of knowledge in the literature was revealed in two areas: understanding how the crystallinity of a polymer changes with time and visualizing the predicted pores formed through the insulator which leads to failure. Developing and using an adapted ATR-FTIR method, crystallinity was monitored and compared to bulk crystallinity found via DSC. Inhomogeneity in crystallinity changes were observed but the FTIR method but was found to be less reliable. Pore visualization was found utilizing electrical impedance spectroscopy saturated aged polyethylene films with synthesized citrate-capped gold nanoparticles, and chloroauric acid precursor. results indicate a decreasing impedance of the polyethylene films caused by the transport of ions through the film. SEM imaging was then performed for elemental analysis of the films and counter electrodes for the presence of ions. Chloride and gold ions were detected; however, no nanoparticles were found. This gives an estimated pore size of at least 0.3 nm through the aged film. Cyclic submergence of polyethylene and polypropylene in aqueous solutions of copper sulfate and Harrison’s solution were examined. It was discovered that aging in these mixed conditions and at 90°C did cause a small, yet significant increase to tensile strength for both unaged polyethylene and polypropylene. The PE and PP in cycled and submerged conditions did not have tensile strengths significantly different from dry-aged after 16 weeks. For both solutions, it was determined that capacitance increases with both water tree depth and cable temperature and is relatively independent of changing water tree AR. As for resistance, there is no apparent change between depth percentages of 10 and 80 for both solutions. This is because the water tree has not yet entered the conductor and thus there is no shorting current flowing through the tree yet. Between 80 and 100% water tree depth, it is observed that for both solutions there is a rapid decrease in resistance because the tree is now impacting the conductor shield and allowing shorting current to flow through it. The relationship between resistance and temperature was found to be inversed. As temperature increases, resistance decreases for both water tree solutions with distilled water having the most apparent difference across the range of temperatures simulated. With regards to water tree AR, resistance was found to be relatively independent at depth percentages of 10, 50, and 70, but there was some relationship at 100% depth for both solutions. At this depth, as water tree AR increased, resistance was found to also increase. Through the examination of voltage and electric field distribution plots, it was confirmed for EPR cables that increasing water tree depth leads to increasing distortion. The increase in shorting current at 100% depth for aqueous copper sulfate compared to distilled water was also visualized. Lastly, the relationship between shorting current and temperature for narrow water trees was visualized and validated using the distribution plots. This study has led to a better understanding of the effect of cable temperature, water tree solution, and geometry of the tree region on cable degradation. Furthermore, this study has documented simulation results of water tree degradation in EPR MV cables, which had been previously lacking in information. Future work in this area will add frequency into the mix and examine what effect it has on the rate of cable degradation as a result of water treeing. To compliment the work being carried by UMD on different polymer chemistries, harvested medium voltage (MV) cables were selected for accelerated aging study at ORNL. These medium voltage cables are representative of the vintages and materials that are currently in use at existing nuclear power plants (NPPs). These cables were immersed in water at 90°C and energized for a period of two years at elevated voltage. Partial discharge was measured during this period of time to track potential degradation. Unfortunately, due to the absence of failure, the extent of integration between the UMD techniques and the harvested MV insulation was limited. However, based on the findings and from the UMD research in the previous sections on polyethylene and polypropylene, follow-on characterization for harvested MV cable insulation should focus on sample preparation to take advantage of the UMD techniques to better understand mechanistic degradation in MV cable insulations. This would include: 1.) Utilization of solutions and impedance measurement insulation to track permeability in harvested and accelerated aging insulation samples, 2.) Adaptation of gold nanoparticle synthesis for electrical impedance spectroscopy with supporting SEM characterization to study pore formation in harvested and accelerated aged insulation samples, & 3.) ATR-FTIR crystallinity with multiple temperature dependent harvested MV cable insulation under different air and submerged accelerated aging. In addition, low voltage dielectric spectroscopy and high voltage dissipation factor, tan δ, could be implemented as a condition monitoring tool for harvested MV cable insulation in submerged environments.
24 POWER TRANSMISSION AND DISTRIBUTION↗
Autonomously Responsive Membranes for Chemical Warfare Protection
Stimuli-responsive materials offer new opportunities to resolve long-standing material challenges and are rapidly gaining pivotal roles in diverse applications. For example, smart protective garments that rapidly transport water vapor and autonomously block chemical threats are expected to enable an effective new paradigm of adaptive personal protection. However, the incorporation of these seemingly incompatible properties into a single responsive system remains elusive. Herein, a bistable membrane that can rapidly, selectively, and reversibly transition from a highly breathable state in a safe environment to a chemically protective state when exposed to organophosphate threats such as sarin is demonstrated. Dynamic response to chemical stimuli is achieved through the physical collapse of an ultrathin copolymer layer on the membrane surface, which efficiently gates transport through membrane pores composed of single-walled carbon nanotubes (SWNTs). The adoption of nanometer-wide SWNTs for ultrafast moisture conduction enables a simultaneous boost in size-sieving selectivity and water-vapor permeability by decreasing nanotube diameter, thereby overcoming the breathability/protection trade-off that limits conventional membrane materials. Adaptive multifunctional membranes based on this platform greatly extend the active use of a protective garment and present exciting opportunities in many other areas including separation processes, sensing, and smart delivery.
36 MATERIALS SCIENCE↗