Search NASA⌕ Search

SEARCH · Search NASA

Results for “wave direction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

The comparison between the synthetic aperture radar imageries and the surface truth of ocean waves

Ocean waves measured offshore of Marineland, Florida, by the synthetic aperture radar (SAR) are compared with the surface truth data. The Fourier transform of SAR imageries are taken and the corrections of the wave directions and wave lengths due to the relative velocities between SAR and waves are considered. Favorable comparisons are obtained for the peak frequencies, wave directions, and directional distributions. However, the one-dimensional SAR spectra are quite different from the surface truth wave height spectra.

Hsiao, S. V.↗

Direct Numerical Simulations of Turbulent Flow over Misaligned Traveling Waves

Direct numerical simulations of turbulent flow over prescribed traveling waves in a half-channel flow setup subject to a combined streamwise and spanwise pressure gradient are performed at a friction Reynolds number of 180. The simulations undertaken in this study consider both flow-aligned (including opposing and following) and misaligned waves as we attempt to quantify the effect of wave misalignment on turbulence statistics, the pressure drag force, and the wave attenuation rate. For the simulations, we consider three characteristic wave age values corresponding to slow-, intermediate-, and fast-moving waves. Wave misalignment is taken into account by applying a spanwise pressure gradient vertical to the traveling waves, which results in a three-dimensional turbulent flow field above the moving waves. Key flow quantities such as the mean velocity, velocity variances, and momentum fluxes are found to vary with the wave parameters, confirming the findings of previous studies.

direct numerical simulation↗

Directional wind wave development

Using aircraft radar instruments designed for sea surface wave measurements, we have obtained fetch-limited directional wind wave spectra under steady off-shore wind conditions. The results from these observations in different areas at different times show that, up to a fetch of 150 km, the dominant waves propagate at an angle to the wind. The angle is near to that suggested by the Phillips resonance wind wave generation condition, but with one important difference: The waves are not always symmetric to the left and right of the wind. Most of the cases show the eventual dominance of one side lobe. The asymmetry of the wave direction relative to the wind suggests that the surface wind stress vector may not always be parallel to the mean wind direction.

Long, Steven R.↗

Wave-current interaction near the Gulf Stream during the surface wave dynamics experiment

This paper presents a case study on the wave-current interaction near the local curvature of a Gulf Stream meander. The wave data were obtained from in situ measurements by a pitch-roll discus buoy during the Surface Wave Dynamics Experiment (SWADE) conducted off Wallops Island, Virginia, from October 1990 to March 1991. Owing to the advection of the Gulf Stream by the semidiurnal tide, the discus buoy was alternately located outside and inside the Gulf Stream. The directional wave measurements from the buoy show the changes in wave direction, wave energy, and directional spreading when waves encountered the current in the Gulf Stream meanders. A wave refraction model, using the ray-tracing method with an estimated Gulf Stream velocity field and meandering condition, was used to simulate wave refraction patterns and to estimate wave parameters at relative locations corresponding to buoy measurements. The numerical simulation shows that a focusing zone of wave rays was formed near the boundary and behind the crest of a simulated Gulf Stream meander. The focusing of wave rays causes changes in wave direction, increases in wave energy, and decreases in wave directional spreading, which are in good agreement with the results from the buoy measurements.

Wang, David W.↗

Direct numerical simulation of isotropic turbulence interacting with a weak shock wave

Direct numerical simulations are used to investigate the interaction of isotropic quasi-incompressible turbulence with a weak shock wave. A linear analysis of the interaction is conducted for comparison with the simulations. Both the simulations and the analysis show that turbulence is enhanced during the interaction. Turbulent kinetic energy and transverse vorticity components are amplified, and turbulent lengthscales are decreased. It is suggested that the amplification mechanism is primarily linear. Simulations also showed a rapid evolution of turbulent kinetic energy just downstream of the shock, a behavior not reproduced by the linear analysis. Analysis of the budget of the turbulent kinetic energy transport equation shows that this behavior can be attributed to the pressure transport term. Multiple compression peaks were found along the mean streamlines at locations where the local shock thickness had increased significantly.

Lee, Sangsan↗

A comparison of SIR-B directional ocean wave spectra with aircraft scanning radar spectra

Directional ocean wave spectra derived from Shuttle Imaging Radar-B (SIR-B) L-band imagery collected off the coast of Southern Chile on 11 and 12 October 1984 were compared with independent spectral estimates from two airborne scanning radars. In sea states with significant wave heights ranging from 3 to 5 meters, the SIR-B-derived sspectra at 18 deg and 25 deg off nadir yielded reasonable estimates of wavelengths, directions, and spectral shapes for all wave systems encountered, including a purely azimuth-traveling system. A SIR-B image intensity variance spectrum containing predominantly range-traveling waves closely resembles an independent aircraft estimate of the slope variance spectrum. The prediction of a U.S. Navy global spectral ocean wave model on 11 October 1984 exhibited no significant bias in dominant wave number but contained a directional bias of about 30 deg with respect to the mean of the aircraft and spacecraft estimates.

Beal, R. C.↗

Directional spectra of ocean waves from microwave backscatter

The paper presents an analysis of two proposed microwave radar techniques for measuring ocean wave directional spectra. Tomiyasu's (1971) short pulse idea and Barrick's (1972) two-frequency correlation idea are regarded - independent of transmitted waveform - as essentially two alternative detection systems for modulated noise. Together, the two systems constitute a general detection system for modulated noise described some years ago by Parzen and Shiren (1956). A frequency domain analysis for backscatter on arbitrary incident waveform is given, and an interesting physical optics solution for the generalized fourth-order moments of the scattering matrix is obtained. It is shown that the present narrowband version of Barrick's two-frequency idea is impractical, and that the proper application of Barrick's idea is to wide band signals.

Jackson, F. C.↗

Measurements of Siple transmitter signals on the DE 1 satellite - Wave normal direction and antenna effective length

A new experimental technique is developed to simultaneously measure the wave propagation direction and the effective length of a small (L value much smaller than wavelength) electric dipole antenna on a spin-stabilized satellite in the magnetosphere. The technique relies on the near simultaneous measurement of single components of the electric and magnetic fields of a coherent VLF signal injected into the medium from a ground-based source. The spin fading characteristics of the signal received by the electric dipole and the magnetic loop antenna permit the measurement of the wave normal direction assuming whistler-mode propagation. In-situ and remote measurements of the local cold plasma density are used to determine the refractive index. The wave electric field is then inferred from the wave magnetic field as measured on the loop antenna, the refractive index and the direction of propagation. Comparing this electric field with the measured voltage across the dipole antenna leads to the determination of the effective length of the receiving electric dipole. The technique is applied to data from the Dynamics Explorer 1 satellite observations of whistler mode signals injected into the magnetosphere from the Siple, Antarctica, VLF transmitter. In one case, with the measured background cold plasma density being 15 el/cu cm, the effective length of the 200 m-long electric dipole antenna is found to be 222 + or - 56 m, i.e., about twice the conventional value.

Sonwalker, V. S.↗

Relationship between directions of wave and energy propagation for cold plasma waves

The dispersion relation for plasma waves is considered in the 'cold' plasma approximation. General formulas for the dependence of the phase and group velocities on the direction of wave propagation with respect to the local magnetic field are obtained for a cold magnetized plasma. The principal cold plasma resonances and cut-off frequencies are defined for an arbitrary angle and are used to establish basic regimes of frequency where the cold plasma waves can propagate or can be evanescent. The relationship between direction of wave and energy propagation, for cold plasma waves in hydrogen atmosphere, is presented in the form of angle diagrams (angle between group velocity and magnetic field versus angle between phase velocity and magnetic field) and polar diagrams (also referred to as 'Friedrich's diagrams') for different directions of wave propagation. Morphological features of the diagrams as well as some critical angles of propagation are discussed.

Musielak, Zdzislaw E.↗

Wave normal directions of chorus near the equatorial source region

OGO 5 triaxial search coil magnetometer data are used to determine the wave propagation directions of postmidnight chorus in the near-equatorial region at L shells of 6 to 7. The methods used to estimate the wave normal directions involved minimum variance, the imaginary part of the cross-spectral matrix, the eigenvector of the Hermitian cross-spectral matrix, and a fitting of dispersion relations for one-wave and two-wave models to the cross-spectral matrix. Wave propagation at all frequencies within chorus tones is found to occur most frequently along the magnetic field with median and average cone angles of 9.1 deg and 12.2 deg, respectively. It is concluded that for waves propagating parallel to B, wave growth is maximum.

Goldstein, B. E.↗

Composite Piezoelectric Resonator 1D Modeling with Loss

Abstract – Maximizing the benefit of applying piezoelectric materials in composite structures, which are a mix of piezoelectric and elastic elements, requires analytical modeling. In this paper we describe two main classes of resonators and how to model using network equivalent including material losses. These include extensional devices where the layer areas are parallel to the direction of wave travel as found in a variety of thickness or length mode transducers (BC. Stress T1 = T2 at boundary) and transverse mode resonators (BC. Strain S1 = S2 at boundary) where the major layer area is perpendicular to the wave direction as is found in radial mode or length thickness mode composite resonators. In order to illustrate these models we will use Mason’s equivalent circuits with elastic, dielectric and piezoelectric loss. It is noted that in order to maintain consistency with the linear equations of piezoelectricity and the wave equation care is required when applying complex loss coefficients to the models. Although these techniques are applicable to other models we use Mason’s network equivalent circuit because it is intuitive for composite modeling due to the frequency independent turns ratio and the independence of the equations describing the elastic layers from the adjoining layer properties which aids in understanding the boundary conditions to impose on the layer boundaries. We will present network models for a variety of applications with loss and show how to calculate their impedance spectra, interface stress, strain velocity and displacement spectra.

Sherrit, Stewart↗

Seasat performance evaluation - The first two steps

Seasat, the satellite dedicated to the study of the oceans using microwave sensors, collected a data set containing information on sea surface winds, sea surface temperatures, wave heights, wave directions, internal waves, currents, tides, the marine geoid, and atmospheric water content. The first two steps of the performance evaluation of the satellite have been completed: (1) the engineering assessment and (2) the sensor evaluation. The results are encouraging for the performance of the instruments and the first level of data processing algorithms.

Lame, D. B.↗

Measuring ocean waves from space; Proceedings of the Symposium, Johns Hopkins University, Laurel, MD, Apr. 15-17, 1986

Papers are presented on ocean-wave prediction; the quasi-universal form of the spectra of wind-generated gravity waves at different stages of their development; the limitations of the spectral measurements and observations of the group structure of surface waves; the effect of swell on the growth of wind wave; operational wave forecasting; ocean-wave models, and seakeeping using directional wave spectra. Consideration is given to microwave measurements of the ocean-wave directional spectra; SIR research; estimating wave energy spectra from SAR imagery, with the radar ocean-wave spectrometer, and SIR-B; the wave-measurement capabilities of the surface contour radar and the airborne oceanographic lidar; and SIR-B ocean-wave enhancement with fast-Fourier transform techniques. Topics discussed include wave-current interaction; the design and applicability of Spectrasat; the need for a global wave monitoring system; the age and source of ocean swell observed in Hurricane Josephine; and the use of satellite technology for insulin treatment.

Beal, Robert C.↗

Polarization ray tracing in anisotropic optically active media

Procedures for performing polarization ray tracing through birefringent media are presented in a form compatible with the standard methods of geometric ray tracing. The birefringent materials treated include the following: anisotropic optically active materials such as quartz, non-optically active uniaxial materials such as calcite, and isotropic optically active materials such as mercury sulfide or organic liquids. Refraction and reflection algorithms are presented which compute both ray directions and wave directions. Methods for computing polarization modes, refractive indices, optical path lengths, and Fresnel transmission and reflection coefficients are also specified.

Mcclain, Stephen C.↗

A Study on Modeled Wind Speed Errors Using the U.S. Department of Energy Buoys

Pacific Northwest National Laboratory (PNNL) operates two AXYS WindSentinel lidar buoys for the U.S. Department of Energy’s Wind Energy Technologies Office. The purpose of these buoys is to collect hub-height winds and supporting meteorological and oceanographic information to facilitate the development of wind energy in the U.S. waters. The first deployment for one buoy was off the coast of Virginia from December 2014 to May 2016, and the first deployment for the other buoy was off the coast of New Jersey from November 2015 until February 2017. This report describes recent analysis of data collected during these first two deployments. Specifically, we compare hub-height wind speed estimates using Monin-Obukhov Similarity Theory (MOST) to the lidar measurements, and examine how those errors are affected by wind direction, atmospheric stability, wind-wave direction differences, and various measures of the wave-state. The comparisons are done using standard similarity functions based on MOST; including the Businger - Dyer, the Beljaars & Holtslag and the Vickers & Mahrt similarity functions. All models produce large errors over the range of atmospheric stabilities that were observed, with the largest errors occurring for stable flows. The Vickers & Mahrt function resulted in the largest overall bias and standard deviation, while Beljaars & Holtslag function gave the smallest bias and standard deviation due to its better performance under stable conditions. The models perform best under unstable conditions, but even in this regime there is a consistent overestimation of the wind speed of between roughly 0 to 1 ms -1 compared to the lidar measurements. We identify specific metocean conditions (i.e. stability and wind and wave directions) at each of the deployment locations that lead to large errors in MOST predictions. Finally, a coupled ocean-atmosphere model framework was investigated to simulate large errors in weather research forecasting (WRF).

17 WIND ENERGY↗

FOSWEC v2: System identification and control testing at Hinsdale Wave Research Laboratory

This report summarizes the design and execution of a wave tank test of the floating oscillating surge wave energy converter (FOSWEC) in the O.H. Hinsdale Wave Research Laboratory Directional Wave Basin at Oregon State University. This device, which uses two "flaps" that pivot about a central platform when excited by waves, has a natural frequency within the range of the waves by which it is excited. The FOSWEC was originally considered to be a 1:33 scale device, however, for the current tests, no fixed relative scale is used (i.e., the WEC is considered to be scaled for the basin’s wave environment in which it operates). The primary goal of this test was to assess the degree to which previously developed modeling, experimentation, and control design methods could be applied to a broad range of wave energy converter designs. Testing was conducted to identify a dynamic model for the impedance and excitation behavior of the device. Using these models, a series of closed loop tests were conducted using a causal impedance matching controller. This report provides a brief description of the results, as well as a summary of the device and experimental design. The results show that the methods applied to this experimental device perform well and should be broadly applicable. The data collected during testing is compressed into FOSWEC.zip. Please refer to Appendix C (pages 61-63) of the test report for descriptions of each test ID corresponding to the compressed files.

16 TIDAL AND WAVE POWER↗

Propagation directions of hydromagnetic waves in interplanetary space - Pioneer 10 and 11

The real and imaginary parts of spectral matrices of magnetic field fluctuations near 4 and 5 AU are used separately to generate estimates of hydromagnetic wave normal directions over the frequency range 0.00001 to 0.01 Hz in the spacecraft frame. Both procedures suggest the predominance of the Alfven mode over the fast and slow MHD modes among transverse magnetic field perturbations. Both procedures also show that the Alfven mode is more common among transverse perturbations at 4 AU than at 5 AU. Statistical techniques are for estimating uncertainties in computed wave normal directions and it is concluded that the real parts of the spectral matrices are more useful than the imaginary parts in specifying wave normals at times of magnetic quiet in the solar wind near 4 and 5 AU.

Parker, G. D.↗

Oceanographic Conditions. 2007 - 2040. North Slope Alaska.

Complete representations of oceanographic conditions require spatial and temporal information about the significant wave height (Hs), peak wave period (Tp), wind speed, wind direction, wave direction, water level, salinity, and temperature. This data develops location-independent typologies to reduce the number of boundary conditions needed to assess nearshore oceanographic environments in both a Historical (2007-2019) and Future (2020-2040) timespan along the Alaskan North Slope. Wave information for both time spans were generated from WaveWatch III, Delft3D-FLOW, and Delft3D-WAVE simulations forced by wind conditions from reanalysis data (e.g., ASRv2 and ERA5) for the historical simulations while projected conditions were obtained from downscaled GFDL-CM3 forced under RCP8.5 conditions. Salinity was generated from GOFS 3.1 for the years between 2008-2015 and skin temperature of the ocean was obtained from ASRv2 reanalysis data for the years between 2007-2016. To identify generalized oceanographic typologies, K-means clustering was applied to the energy-weighted joint-probability distribution of Hs and Tp at six sites along the North Slope of Alaska. Distributions of wave and wind direction, wind speed, and water level associated with locaiton-indepndent centroids were assigned single values to describe a reduced order, typological rendition of offshore oceanographic conditions. These final typologies and their constituent data are provided here and can be used to evaluate the change in ocean energy over the next two decades in response to climate change and provide insight into expected consequences such as coastal erosion and flooding. A full assessment of the findings and techniques developed can be found in: Eymold, W.K., Flanary, C., Erikson, L., Nederhoff, K., Chartrand, C.C., Jones, C., Kasper, J., and Bull, D.L. Typological Representation of the Offshore Oceanographic Environment along the Alaskan North Slope. Continental Shelf Research (2022). 10.1016/j.csr.2022.104795

54 ENVIRONMENTAL SCIENCES↗