SEARCH · Search NASA

Results for “wing design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Subsonic panel method for designing wing surfaces from pressure distribution

An iterative method has been developed for designing wing section contours corresponding to a prescribed subcritical distribution of pressure. The calculations are initialized by using a surface panel method to analyze a baseline wing or wing-fuselage configuration. A first-order expansion to the baseline panel method equations is then used to calculate a matrix containing the partial derivative of potential at each control point with respect to each unknown geometry parameter. In every iteration cycle, the matrix is used both to calculate the geometry perturbation and to analyze the perturbed geometry. The distribution of potential on the perturbed geometry is established by simple linear extrapolation from the baseline solution. The extrapolated potential is converted to pressure by Bernoulli's equation. Not only is the accuracy of the approach good for very large perturbations, but the computing cost of each complete iteration cycle is substantially less than one analysis solution by a conventional panel method.

Bristow, D. R.↗

NASA NTRS1985

Nonlinear aerodynamic wing design

The applicability of new nonlinear theoretical techniques is demonstrated for supersonic wing design. The new technology was utilized to define outboard panels for an existing advanced tactical fighter model. Mach 1.6 maneuver point design and multi-operating point compromise surfaces were developed and tested. High aerodynamic efficiency was achieved at the design conditions. A corollary result was that only modest supersonic penalties were incurred to meet multiple aerodynamic requirements. The nonlinear potential analysis of a practical configuration arrangement correlated well with experimental data.

Bonner, Ellwood↗

NASA NTRS1977

Wing design by numerical optimization

A study was conducted to assess the feasibility of performing computerized wing design by numerical optimization. The design program combined a full potential, inviscid aerodynamics code with a conjugate gradient optimization algorithm. Three design problems were selected to demonstrate the design technique. The first involved modifying the upper surface of the inboard 50% of a swept wing to reduce the shock drag subject to a constraint on wing volume. The second involved modifying the entire upper surface of the same swept wing (except the tip section) to increase the lift-drag ratio subject to constraints on wing volume and lift coefficient. The final problem involved modifying the inboard 50% of a low-speed wing to achieve good stall progression. Results from the three cases indicate that the technique is sufficiently accurate to permit substantial improvement in the design objectives.

Hicks, R. M.↗

NASA NTRS1996

Novel Composites for Wing and Fuselage Applications: Novel Wing Design Concepts - Task 1

Design trade studies were conducted to arrive at advanced wing designs that integrated new material forms with innovative structural concepts and cost-effective fabrication methods. A representative spar was selected for design, fabrication, and test to validate the predicted performance. Textile processes, such as knitting, weaving and stitching, were used to produce fiber preforms that were later fabricated into composite span through epoxy Resin Transfer Molding (RTM), Resin Film Infusion (RFI), and consolidation of commingled thermoplastic and graphite tows. The target design ultimate strain level for these innovative structural design concepts was 6000 mu in. per in. The spars were subjected to four-point beam bending to validate their structural performance. The various material form /processing combination Y-spars were rated for their structural efficiency and acquisition cost. The acquisition cost elements were material, tooling, and labor.

Suarez, J. A.↗

NASA NTRS1989

The use of a Navier-Stokes code in the wing design process

The feasibility was determined of incorporating the Navier-Stokes computational code, CFL3D, into the supersonic wing design process. The approach taken is of two steps. The first step was to calibrate CFL3D against existing experimental data sets obtained on thin sharp edged delta wings. The experimental data identified six flow types which are dependent on the similarity parameters of Mach number and angle of attack normal to the leading edge. The calibration showed CFL3D capable of simulating these various separated and attached flow conditions. The second step was to use CFL3D to study the initial formation of leading edge separation over delta wings at supersonic speeds. This consisted of examining solutions obtained on a 65 deg delta wing at Mach number of 1.6 with varying cross sectional shapes. Reynolds number was held constant at 1000000 and the Baldwin-Lomax turbulence model was used. The study showed that through the use of leading edge radius and/or camber, the onset of leading edge separation can be delayed to a higher angle of attack than observed on a flat sharp edged wing. Based on the geometries studied, three wind tunnel models are being designed to verify these results.

Mcmillin, S. Naomi↗

NASA NTRS1981

Computer program documentation for a subcritical wing design code using higher order far-field drag minimization

A subsonic, linearized aerodynamic theory, wing design program for one or two planforms was developed which uses a vortex lattice near field model and a higher order panel method in the far field. The theoretical development of the wake model and its implementation in the vortex lattice design code are summarized and sample results are given. Detailed program usage instructions, sample input and output data, and a program listing are presented in the Appendixes. The far field wake model assumes a wake vortex sheet whose strength varies piecewise linearly in the spanwise direction. From this model analytical expressions for lift coefficient, induced drag coefficient, pitching moment coefficient, and bending moment coefficient were developed. From these relationships a direct optimization scheme is used to determine the optimum wake vorticity distribution for minimum induced drag, subject to constraints on lift, and pitching or bending moment. Integration spanwise yields the bound circulation, which is interpolated in the near field vortex lattice to obtain the design camber surface(s).

Kuhlman, J. M.↗

NASA NTRS1981

Transonic wing design using potential-flow codes - Successes and failures

The state-of-the-art of transonic wing design by use of computer codes based on the potential flow-theory is presented. The capabilities and limitations of these codes are exemplified by several experiment-theory correlations, including an assessment of pressure distribution from isolated wing and wing-body codes. Computer codes using both conservative and nonconservative differencing schemes were used, and the effects of boundary-layer corrections were considered. Results showed that calculations from a full potential, isolated code correlate well with data from an isolated wing test, but may give poor predictions of the aerodynamic characteristics of some wing-body configurations. Boundary-layer correlations were found to have only moderate effects on experiment-theory correlation. Aeroelastic effects were considered important for high aspect ratio wings of low to moderate thickness, and viscous effects were minimal for typical cruise conditions, even for Reynold's numbers as low as two million. The effect of wind-tunnel walls on experiment-theory correlations remained inconclusive. A wing-body code was used to calculate the flow field about a wing-body configuration with body-mounted engines, typical of the transonic Biz-Jet aircraft.

Hicks, R. M.↗

NASA NTRS1981

Overview of advanced wing design

Examples of experiment theory correlation are presented to give an indication of the capabilities and limitations of wing design and analysis for transonic applications by potential flow theory. The examples include correlations of experimental pressure distributions with theoretical results from isolated wing codes and wing-body codes. Both conservative and non conservative differencing as well as body and boundary layer corrections are considered. A full potential isolated wing code correlates well with data from an isolated wing test but may give poor prediction of the aerodynamic characteristics of some wing-body configurations. Potential flow wing body codes were found to improve the correlation for the wing-body configurations considered.

Hicks, R. M.↗

NASA NTRS1974

Computer-aided space shuttle orbiter wing design study

An analytical and experimental investigation has been made to provide a space shuttle orbiter wing design that met the guideline requirements of landing performance, stability, and hypersonic trim for a specified center-of-gravity envelope. The analytical study was facilitated by the use of the Optimal Design Integration system (ODIN) and the experimental part of the investigation was conducted in the Langley low-turbulence pressure tunnel and the Langley continuous-flow hypersonic tunnel.

Phillips, W. P.↗

NASA NTRS1974

Calculation of the twist distribution of wings designed for cruise at transonic speeds

The use of linear theory in calculating the twist distribution of a wing designed for cruise at supercritical speeds is justified on the basis of the transonic equivalence rule. A modified version of Multhopp's subsonic lifting-surface theory was used to calculate the twist distribution. The lifting-surface theory is compared with both slender wing theory and experimental results. A study was also made of the effect of wing sweep on the twist distribution required to maintain an elliptic span load at cruise conditions. The important parameters used in establishing this twist distribution are identified.

Mann, M. J.↗

NASA NTRS1984

Supersonic wing design concepts employing nonlinear flows

Three nonlinear flow concepts for the design of supersonic wings are reviewed. The specific concepts are: leading-edge thrust, supercritical crossflow, and leading-edge vortex flow. The major results of the experimental-theoretical studies supporting the development of these concepts are presented and discussed. Also, supporting aerodynamic prediction methods are described and example applications are given. Recommendations for further development of each concept are made.

Miller, D. S.↗

NASA NTRS1984

Applications of CONMIN to wing design optimization with vortex flow effect

Slender wings on supersonic cruise configurations are expected to be thin and highly swept. As a result, edge-separated vortex flow is inevitable and must be accounted for in aerodynamic analysis and design. The present method is based on the method of suction analogy to calculate the total aerodynamic characteristics. The method requires the solution of the attached flow problem, the latter being solved by a low-order panel method in subsonic and supersonic flow. In essence, the lifting pressure is calculated by using a pressure-doublet distribution satisfying the Prandtl-Glauert equation. From the pressure distribution, the leading-edge suction is calculated. The latter is assumed to be the vortex lift through the method of suction analogy. For a cambered wing, the location of vortex-lift action point is important in predicting the aerodynamic characteristics. It is also seen that the effect of camber shape appears nonlinearly in all aerodynamic expressions. To design the camber shape, the camber slope is represented by a cosine Fourier series at each of several spanwise stations. The Fourier coefficients are the design variables. To design a leading-edge flap in the vortex flow (i.e., a vortex flap), the coordinates of corner points and the deflection angle are the design variables. The process of wing design is to determine the camber shape and twist distribution such that an objective function, typically the drag, is minimized, subject to various constraints.

Lan, C. E.↗

NASA NTRS1992

Lightplane Wing Design

Venture, a kit airplane designed and manufactured by Questair, is a high performance lightplane with excellent low speed characteristics and enhanced safety due to NASA technology incorporated in its unusual wing design. In 1987, North Carolina State graduate students and Langley Research Center spent seven months researching and analyzing the Venture. The result was a wing modification, improving control and providing more usable lift. The plane subsequently set 10 world speed records.

Source record↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

The present computational study investigates the aerodynamic design and analysis of cruise slotted wings with natural laminar flow for transonic transport aircraft. The cruise slotted wing is a multielement wing concept that features an intermediate slot to achieve greater aft loading relative to supercritical wings for the potential benefit of reduced shock strength and pressure drag. Transonic near-cruise, off-design assessments have also shown improved drag rise characteristics due to the ability of the slot to mitigate boundary layer separation on the aft flap component. However, due to the decreased Reynolds number of the flap, the cruise slotted wing has historically incurred a skin-friction drag penalty relative to a conventional supercritical wing. To offset this penalty, a cruise slotted wing with the forward main element and aft flap element shaped to achieve natural laminar flow is desired. Toward this effort, a knowledge-based aerodynamic design method, CDISC, has been leveraged to design a partial-span cruise slotted wing with natural laminar flow for a Mach-0.8 variant of the Common Research Model. Drag comparisons will be provided at cruise and near-cruise, off-design conditions relative to both fully turbulent and natural laminar flow conventional wing designs. It is anticipated that pairing natural laminar flow technology with the cruise slotted wing architecture will allow for cruise drag performance similar to conventional laminar flow wings with improved drag rise characteristics and more limited laminar-flow sensitivity at off-design conditions. Preliminary results for a cruise slotted wing with laminar flow on the outboard wing section only have shown a 10-ct cruise drag reduction relative to a conventional supercritical wing, but a 8-ct penalty relative to the conventional NLF wing. The final paper will include results for a cruise slotted wing design with laminar flow on both the inboard and outboard wing sections.

CFD↗

NASA NTRSDate not supplied

Cruise Slotted Wing Design with Natural Laminar Flow for Transonic Commercial Transport Aircraft

Natural Laminar Flow↗

NASA NTRS1992

Integrated aerodynamic-structural-control wing design

The aerodynamic-structural-control design of a forward-swept composite wing for a high subsonic transport aircraft is considered. The structural analysis is based on a finite-element method. The aerodynamic calculations are based on a vortex-lattice method, and the control calculations are based on an output feedback control. The wing is designed for minimum weight subject to structural, performance/aerodynamic and control constraints. Efficient methods are used to calculate the control-deflection and control-effectiveness sensitivities which appear as second-order derivatives in the control constraint equations. To suppress the aeroelastic divergence of the forward-swept wing, and to reduce the gross weight of the design aircraft, two separate cases are studied: (1) combined application of aeroelastic tailoring and active controls; and (2) aeroelastic tailoring alone. The results of this study indicated that, for this particular example, aeroelastic tailoring is sufficient for suppressing the aeroelastic divergence, and the use of active controls was not necessary.

Rais-Rohani, M.↗

NASA NTRS1988

Aerodynamic characteristics of wings designed with a combined-theory method to cruise at a Mach number of 4.5

A wind-tunnel study was conducted to determine the capability of a method combining linear theory and shock-expansion theory to design optimum camber surfaces for wings that will fly at high-supersonic/low-hypersonic speeds. Three force models (a flat-plate reference wing and two cambered and twisted wings) were used to obtain aerodynamic lift, drag, and pitching-moment data. A fourth pressure-orifice model was used to obtain surface-pressure data. All four wing models had the same planform, airfoil section, and centerbody area distribution. The design Mach number was 4.5, but data were also obtained at Mach numbers of 3.5 and 4.0. Results of these tests indicated that the use of airfoil thickness as a theoretical optimum, camber-surface design constraint did not improve the aerodynamic efficiency or performance of a wing as compared with a wing that was designed with a zero-thickness airfoil (linear-theory) constraint.

Mack, Robert J.↗

NASA NTRS1995

Optimization on a Network-based Parallel Computer System for Supersonic Laminar Wing Design

A set of Computational Fluid Dynamics (CFD) routines and flow transition prediction tools are integrated into a network based parallel numerical optimization routine. Through this optimization routine, the design of a 2-D airfoil and an infinitely swept wing will be studied in order to advance the design cycle capability of supersonic laminar flow wings. The goal of advancing supersonic laminar flow wing design is achieved by wisely choosing the design variables used in the optimization routine. The design variables are represented by the theory of Fourier series and potential theory. These theories, combined with the parallel CFD flow routines and flow transition prediction tools, provide a design space for a global optimal point to be searched. Finally, the parallel optimization routine enables gradient evaluations to be performed in a fast and parallel fashion.

Garcia, Joseph A.↗