Search NASA⌕ Search

SEARCH · Search NASA

Results for “3D PRINTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

SU-C-213-02: Characterizing 3D Printing in the Fabrication of Variable Density Phantoms

Purpose: In this work, we present characterization, process flow, quality control and application of 3D fabricated low density phantoms for radiotherapy quality assurance. Methods: A Rostock delta 3D printer using polystyrene filament of diameter 1.75 mm was used to print geometric volumes of 2×2×1 cm{sup 3} of varying densities. The variable densities of 0.1 to 0.75 g/cm {sup 3} were created by modulating the infill. A computed tomography (CT) scan was performed to establish an infill-density calibration curve as well as characterize the quality of the print such as uniformity and the infill pattern. The time required to print these volumes was also recorded. Using the calibration, two low density cones (0.19, 0.52 g/cm{sup 3}) were printed and benchmarked against commercially available phantoms. The dosimetric validation of the low density scaling of Anisotropic Analytical Algorithm (AAA) was performed by using a 0.5 g/cm{sup 3} slab of 10×10×2.4 cm{sup 3} with EBT3 GafChromic film. The gamma analysis at 3%/3mm criteria were compared for the measured and computed dose planes. Results: Analysis of the volume of air pockets in the infill resulted in a reasonable uniformity for densities 0.4 to 0.75 g/cm{sup 3}. Printed phantoms with densities below 0.4 g/cm{sup 3} exhibited a higher ratio of air to polystyrene resulting in large non-uniformity. Compared to the commercial inserts, good agreement was observed only for the printed 0.52 g/cm{sup 3} cone. Dosimetric comparison for a printed low density volume placed in-between layers of solid water resulted in >95% gamma agreement between AAA calculated dose planes and measured EBT3 films for a 6MV 5×5 cm{sup 2} clinical beam. The comparison showed disagreement in the penumbra region. Conclusion: In conclusion, 3D printing technology opens the door to desktop fabrication of variable density phantoms at economical prices in an efficient manner for the quality assurance needs of a small clinic.

60 APPLIED LIFE SCIENCES↗

Biomaterials Out of Thin Air: In Situ, On-Demand Printing of Advanced Biocomposites: A New Materials Design and Production Technique Using 3D-Printed Arrays of Bioengineered Cells

We have completed the proof of concept described in our Phase I proposal, a two-material array of nonstructural proteins. We created an implementation of each step in our technology concept and demonstrated its critical functionality. The biological chassis and printing hardware we created as part of this work can be re-used for future work by inserting a material coding region upstream of the fluorescent tag. Overall, we showed that our technology concept is sound. The mission benefit analyses, as described in our Phase I proposal, are complete and contained in this report. These calculations show that our technology can save hundreds of kilograms of upmass for a potential planetary human habit construction mission: the mass per habitat module can be reduced by approximately one third if the biomaterials are manufactured on Earth and included in the mission upmass, and the full 240 kg per module can be saved if the materials are derived entirely from in situ resources. Mass savings between these two extremes is expected for an actual mission, depending on the level of in situ resource extraction technology. We have shown that continued advancement of this technology concept for use in a space mission environment is justified. Our survey of future development pathways proved extremely informative in light of the lessons learned from our proof of concept work and mission scenario analyses. For example, we were able for the first time to distinguish between the levels of functionality provided by production of structural proteins, other polymers such as polysaccharides, and true organic-inorganic composites such as bone and mineralized shell. This new information represents a significant advance in formulating specific applications, and key enabling technologies, for our proposed concept. We surveyed potential collaborations with other projects and synergies with enabling technologies that are developing. We have received requests for collaboration from other institutions, including labs at Stanford University and Drexel University. We have also received visits from industry, including Organovo, a tissue engineering company, and Autodesk, a major 3D and materials design software company. Finally, we have been in touch with the team behind the 2013 NIAC Phase ll 'Super Ball Bot-Structures for Planetary Landing and Exploration' and are planning to develop our biomaterial printing technology with the goal of enabling tensegrity-based rovers such as theirs to use lighter, more robust materials. A smooth transition from TRL 2 to TRL 3 assumes that the implementations of the technology concept which demonstrate critical functionality are also pathways for future development; while this is the case for most hardware or software projects, the multidisciplinary nature of our project, particularly the biological aspect of it, means that this is not always true. For example, as part of this work we showed that although there are large number of known genetic parts that correspond to non-structural materials, this is not true for sequences for structural organic proteins, let alone biominerals. These realizations allowed us to further subdivide our concept into more detailed development areas, some of which are clearly established at TRL 3, others of which were newly identified sub-technologies moved from TRL 1 to TRL 2. Similarly, although a single feasibility /benefit analysis is sufficient for advancement from TRL 2 to TRL 3, not all potential benefits to a technology concept as broad in scope as ours are apparent at TRL 2. Both our future pathways survey and our proof of concept work highlighted that the true mass savings potential of our technology concept cannot be quantified without modification of existing materials modelling tools to take into account the possibility of positional materials properties customization. Therefore, we have simultaneously both advanced one potential set of applications of our technology concept from TRL 2 to TRL 3 and also identified a previously unknown set of applications and advanced it from TRL 1 to TRL 2. Overall, we have moved the original formulation of our concept forward from TRL 2 to TRL 3, and the expanded formulation of it presented in this document has been advanced from a combination of TRL 1 and early 1RL 2 to an overall late TRL 2. We have also identified the key areas necessary for both short-term and long-term advancement, and made recommendations for specific future work in the most promising directions. With future work on a 1-2 year timeframe to continue advancement to overall TRL 3, we will be well positioned to begin work on a specific space mission technology insertion path.

Biology↗

3D Printed Multifunctional, Hyperelastic Silicone Rubber Foam

Highly elastic silicone foams, especially those with tunable properties and multifunctionality, are of great interest in numerous fields. However, the liquid nature of silicone precursors and the complicated foaming process hinder the realization of its three-dimensional (3D) printability. Herein, a series of silicone foams with outstanding performance with regards to elasticity, wetting and sensing properties, multifunctionality, and tunability is generated by direct ink writing. Viscoelastic inks are achieved from direct dispersion of sodium chloride in a unique silicone precursor solution. The 3D-architectured silicone rubber exhibits open-celled trimodal porosity, which offers ultraelasticity with hyper compressibility/cycling endurance (near-zero stress/strain loss under 90% compression or 1000 compression cycles), excellent stretchability (210% strain), and superhydrophobicity. The resulting foam is demonstrated to be multifunctional, such that it can work as an oil sorbent with super capacity (1320%) and customizable soft sensor after absorption of carbon nanotubes on the foam surface. The strategy enables tunability of mechanical strength, elasticity, stretchability, and absorbing capacity, while printing different materials together offers property gradients as an extra dimension of tunability. Finally, the first 3D printed silicone foam, which serves an important step toward its application expansion, is achieved.

36 MATERIALS SCIENCE↗

3D Printing Prototypes for a Reflector-Based Broadband Axion Search

This work sought to begin research and development on a horn antenna which can be used to transfer the energy of microwave photons produced by axions in a strong magnetic field to a coaxial cable for measurement. 3D prototypes of pyramidal horn antennas and a parabolic reflector were printed and then coated with conductive spray paint. The S 11 parameter was measured and simulated for both 3D printed horn antenna and the conical horn antenna both with and without the reflector present to determine how much of the radiated power was reflected back. Ultimately, for both the conical and pyramidal antennas, less than one percent of the energy emitted by the antennas was reflected back. When the pyramidal antenna was tilted by about 45 degrees, however, around 30-40 percent of the microwaves emitted by the antennas was reflected back.

43 PARTICLE ACCELERATORS↗

3D scanning and 3D printing AlSi10Mg single crystal mounts for neutron scattering

Here, we present methods to quantify sample shapes and generate sample mounts as motivated by the needs of neutron scattering experiments. The 3D sample scanning was performed using photogrammetry and laser scanning, and a comparison is made between the two techniques. The aluminum alloy AlSi10Mg is shown to have favorable properties for many types of mounts used in neutron scattering. Parts were first prototyped with 3D plastic printers, and then, 3D AlSi10Mg prints were made. The final additively manufactured part holds the sample with more points of contact than is possible with traditional manufacturing. The goodness of fit between the mount and sample was measured by x-ray tomography.

47 OTHER INSTRUMENTATION↗

Hydrogen trapping in 3D-printed (additive manufactured) Ti-6Al-4V

Highlights: • The AM process influence hydrogen trapping and desorption behavior. • Susceptibility to hydrogen embrittlement significantly depends on the printing direction. • Hydrogen desorption in SLM Ti-6Al-4V is designated to dislocations and Ti-hydride phase. - Abstract: Hydrogen trapping state and desorption behavior in 3D printed-Ti-6Al-4V, designed using additive manufacturing (AM), have been investigated. The AM process in this work is selective laser melting (SLM) by which components are built using melting powder's layers with a laser beam. During this process, hydrogen can meet with Ti, leading to a catastrophically failure known as hydrogen embrittlement. The effect of hydrogen on different textural anisotropy of AM-Ti-6Al-4V, and on metal's defect (created during the SLM process), have been studied in relation with hydrogen trapping state, and hydrogen embrittlement. The common effect of hydrogen on phase transformation in AM-Ti-6Al-4V has been shown. It is shown that the susceptibility to hydrogen embrittlement significantly depends on the printing direction. The impact of hydrogen desorption on AM-Ti-6Al-4V have been demonstrated with thermal desorption spectrometry (TDS), X-ray diffraction (XRD) and microstructural observations.

36 MATERIALS SCIENCE↗

3D Printed Parahydrophobic Surfaces as Multireaction Platforms

We report Parahydrophobic surfaces (PHSs) composed of arrays of cubic μ-pillars with a double scale of roughness and variable wettability were systematically obtained in one step and a widely accessible stereolithographic Formlabs 3D printer. The wettability control was achieved by combining the geometrical parameters (H = height and P = pitch) and the surface modification with fluoroalkyl silane compounds. Homogeneous distribution of F and Si atoms onto the pillars was observed by XPS and SEM-EDAX. A nano-roughness on the heads of the pillars was achieved without any post-treatment. The smallest P values lead to surfaces with static contact angles (CAs) >150° regardless of the H utilized. Interestingly, the relationship 0.6 ≤ H/P ≤ 2.6 obtained here was in good agreement with the H/P values reported for nano- and submicron pillars. Furthermore, experimental CAs, advancing and receding CAs, were consistent with the theoretical prediction from the Cassie–Baxter model. Structures covered with perfluorodecyltriethoxysilane with high H and short P lead to PHSs. Conversely, structures covered with perfluorodecyltrimethoxysilane exhibited a superhydrophobic behavior. Finally, several aqueous reactions, such as precipitation, coordination complex, and nanoparticle synthesis, were carried out by placing the reactive agents as microdroplets on the parahydrophobic pillars, demonstrating the potential application as chemical multi-reaction array platforms for a large variety of relevant fields in microdroplet manipulation, microfluidics systems, and health monitoring, among others.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A defect-resistant Co–Ni superalloy for 3D printing

Abstract Additive manufacturing promises a major transformation of the production of high economic value metallic materials, enabling innovative, geometrically complex designs with minimal material waste. The overarching challenge is to design alloys that are compatible with the unique additive processing conditions while maintaining material properties sufficient for the challenging environments encountered in energy, space, and nuclear applications. Here we describe a class of high strength, defect-resistant 3D printable superalloys containing approximately equal parts of Co and Ni along with Al, Cr, Ta and W that possess strengths in excess of 1.1 GPa in as-printed and post-processed forms and tensile ductilities of greater than 13% at room temperature. These alloys are amenable to crack-free 3D printing via electron beam melting (EBM) with preheat as well as selective laser melting (SLM) with limited preheat. Alloy design principles are described along with the structure and properties of EBM and SLM CoNi-base materials.

36 MATERIALS SCIENCE↗

3D Printed Robotic Hand

Dexterous robotic hands are changing the way robots and humans interact and use common tools. Unfortunately, the complexity of the joints and actuations drive up the manufacturing cost. Some cutting edge and commercially available rapid prototyping machines now have the ability to print multiple materials and even combine these materials in the same job. A 3D model of a robotic hand was designed using Creo Parametric 2.0. Combining "hard" and "soft" materials, the model was printed on the Object Connex350 3D printer with the purpose of resembling as much as possible the human appearance and mobility of a real hand while needing no assembly. After printing the prototype, strings where installed as actuators to test mobility. Based on printing materials, the manufacturing cost of the hand was $167, significantly lower than other robotic hands without the actuators since they have more complex assembly processes.

Pizarro, Yaritzmar Rosario↗