SEARCH · Search NASA

Results for “Configuration Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Application of active control landing gear technology to the A-10 aircraft

Two concepts which reduce the A-10 aircraft's wing/gear interface forces as a result of applying active control technology to the main landing gear are described. In the first concept, referred to as the alternate concept a servovalve in a closed pressure control loop configuration effectively varies the size of the third stage spool valve orifice which is embedded in the strut. This action allows the internal energy in the strut to shunt hydraulic flow around the metering orifice. The command signal to the loop is reference strut pressure which is compared to the measured strut pressure, the difference being the loop error. Thus, the loop effectively varies the spool valve orifice size to maintain the strut pressure, and therefore minimizes the wing/gear interface force referenced.

Ross, I.↗

NASA NTRS1983

Analytic redundance management for flight control sensors

The formulation and flight test results of an algorithm to detect and isolate the first failure of any one of 12 duplex control sensor signals (24 in all) being monitored are reviewed. The technique uses like signal differences for fault detection while relying upon analytic redundancy relationships among unlike quantities to isolate the faulty sensor. The fault isolation logic utilizes the modified sequential probability ratio test, which explicitly accommodates the inevitable, irreducible low frequency errors present in the analytic redundancy residuals. In addition, the algorithm used sensor output selftest, which takes advantage of the duplex sensor structure by immediately removing a hard failed sensor from control calculations and analytic redundancy relationships while awaiting a definitive fault isolation decision via analytic redundancy. This study represents a proof of concept demonstration of a methodology that is applied to duplex or higher flight control sensor configurations and, in addition, can monitor the health of one simplex signal per analytic redundancy relationship.

Deckert, J. C.↗

NASA NTRS1983

NASA technology program for future civil air transports

An assessment is undertaken of the development status of technology, applicable to future civil air transport design, which is currently undergoing conceptual study or testing at NASA facilities. The NASA civil air transport effort emphasizes advanced aerodynamic computational capabilities, fuel-efficient engines, advanced turboprops, composite primary structure materials, advanced aerodynamic concepts in boundary layer laminarization and aircraft configuration, refined control, guidance and flight management systems, and the integration of all these design elements into optimal systems. Attention is given to such novel transport aircraft design concepts as forward swept wings, twin fuselages, sandwich composite structures, and swept blade propfans.

Wright, H. T.↗

NASA NTRS1985

Development of the space shuttle body flap actuation subsystem

Development of the Body Flap Actuation Subsystem for Space Shuttles included alterations from the original design to mechanical stops, planet gears, control valves, and solenoid valves. The mechanical stops were redesigned to absorb stall load and rotating inertia of the hydraulic motors instead of only stall load. The institution of a quill shaft (torsion spring) was a successful solution. The planet gears in the geared rotary actuators developed cracks during testing. This failure was alleviated via modification to the gears. A motor pressurization - brake release timing technique was developed thru analysis and testing. This resulted in a control valve configuration which would not permit freewheeling of the body flap surface. Finally, several solenoid valve configurations were tested to obtain the desired performance. Conceptual redesigns and modifications were weighted against each other to optimize a solution. Tradeoffs were usually made between life, performance, failure tolerance, and reliability versus weight, envelope, and maintainability.

Boggs, C. R.↗

NASA NTRS1985

Summary presentation of the Constellations Panel

Tethered multiple spacecraft configurations are discussed relative to low Earth orbit, geosynchronous Earth orbit, and one, two, or three dimensional configurations. Attitude control, pointing, and stabilization of such tethered systems are addressed.

Williams, F.↗

NASA NTRS1985

Space station trace contaminant control

Different systems for the control of space station trace contaminants are outlined. The issues discussed include: spacecabin contaminant sources, technology base, contaminant control system elements and configuration, approach to contaminant control, contaminant load model definition, spacecraft maximum allowable concentrations, charcoal bed sizing and performance characteristics, catalytic oxidizer sizing and performance characteristics, special sorbent bed sizing, animal and plant research payload problems, and emergency upset contaminant removal. It is concluded that the trace contaminant control technology base is firm, the necessary hardware tools are available, and the previous design philosophy is still applicable. Some concerns are the need as opposed to danger of the catalytic oxidizer, contaminants with very low allowable concentrations, and the impact of relaxing materials requirements.

Olcutt, T.↗

NASA NTRS1985

The interpretation of flying qualities requirements for flight control system design

An experimental flight test program was designed for the Total In Flight Simulator (TIFS) directed toward the interface between flying qualities requirements and flight control system design criteria. The eventual goal is to provide an interpretation or translation of flying qualities requirements for use by the flight control system designer. Specifically, an angle of attack and pitch rate command system matrix involving both short term and long term dynamics are specified for evaluation. Flying qualities criteria and flight control system configuration or architecture can be independent was demonstrated. Finally, additional configurations are proposed to evaluate the efficacy of dynamic decoupling.

Rynaski, E. G.↗

NASA NTRS1984

SP-100 space nuclear power system

A baseline design concept for a 100 kWe nuclear reactor space power system is described. The concept was developed under contract from JPL as part of a joint program of the DOE, DOD, and NASA. The major technical and safety constraints influencing the selection of reactor operating parameters are discussed. A lithium-cooled compact fast reactor was selected as the best candidate system. The material selected for the thermoelectric conversion system was silicon germanium (SiGe) with gallium phosphide doping. Attention is given to the improved safety of the seven in-core control rod configuration.

Given, R. W.↗

NASA NTRS1986

Verification of post permanently manned configuration Space Station elements

An account is given of the techniques and ground systems designed to fulfill post permanently manned configuration (PMC) Space Station verification tasks. Consideration is given to analysis using computer math models and computer-aided interface verification systems, testing using simulators and interface mixtures, and special inspection. It is noted that an initial Space Station design that accommodates and facilitates verification is crucial to an effective verification program as well as proper instrumentation, built-in test capability, and a precise configuration management, control and record system. It is concluded that post PMC verification should be accounted for both in the initial Space Station design and in the subsequent development of initial assembly flight verification techniques and capabilities.

Scully, E. J.↗

NASA NTRS1986

A guidance-motivated sensitivity analysis of an aero-assisted boost vehicle

A simple model of an aero-assisted booster is used to examine the contributions of propulsion system type, aerodynamic lift and flight trajectory to the efficiency with which payloads can be placed into low earth orbit. The higher propulsive efficiency of ramjet and scramjet propulsion has the potential of increasing the payload mass ratio significantly. The contributions of turbojet propulsion and aerodynamic lift are less significant. The additional complexity involved in using aerodynamic propulsion and lift requires dealing with a more comprehensive set of design variables than for rocket boosters. The approach taken is to derive a set of sensitivity functions which relate booster performance to the design variables. The problems of optimum mixing of aerodynamic lift with thrust and determining the optimal boost trajectory is treated. The potential payload capacity of a horizontal take-off air-breathing boost vehicle is examined. The optimization problem which considers propulsive efficiency, aerodynamic configuration, and control and guidance issues is discussed.

Taylor, L. W.↗

NASA NTRS1986

Pilot vehicle interface on the advanced fighter technology integration F-16

This paper focuses on the work load aspects of the pilot vehicle interface in regard to the new technologies tested during AMAS Phase II. Subjects discussed in this paper include: a wide field-of-view head-up display; automated maneuvering attack system/sensor tracker system; master modes that configure flight controls and mission avionics; a modified helmet mounted sight; improved multifunction display capability; a voice interactive command system; ride qualities during automated weapon delivery; a color moving map; an advanced digital map display; and a g-induced loss-of-consciousness and spatial disorientation autorecovery system.

Dana, W. H.↗

NASA NTRS1988

Reliability Model Generator for fault-tolerant systems

This paper discusses an analysis tool, the Reliability Model Generator, that reasons from structural and functional system design specifications to generate a reliability model for the system under investigation. The resultant model defines a system state space sufficient to characterize the effects of single and multiple component failures. This model may then be examined by the analyst or used as input to an existing reliability evaluation tool, the Semi-Markov Unreliability Range Evaluator (SURE), to compute numeric bounds for system reliability (i.e., safety, mission success, availability, etc.). In defining the input to the Reliability Model Generator, a separation of the component function from structural specification is proposed to allow easy modification for analysis of alternative architectures. A hierarchical system description paradigm promotes multiple abstractions, thereby enabling analysis at all phases of the design process. The work described in this paper has been supported under NASA contract NAS1-10899, Integrated Airframe/Propulsion Control System Architecture (IAPSA II). IAPSA II promotes a system engineering methodology and supporting analytical tools to evaluate flight control architecture configuration alternatives during early phases of the design cycle when the cost and schedule impact of design revisions is minimal. Emphasis is placed on traceability to ensure that the requirements drive the resulting design.

Catherine M McCann↗

NASA NTRS1987

Stability theory applications to laminar-flow control

In order to design Laminar Flow Control (LFC) configurations, reliable methods are needed for boundary-layer transition predictions. Among the available methods, there are correlations based upon R sub e, shape factors, Goertler number and crossflow Reynolds number. The most advanced transition prediction method is based upon linear stability theory in the form of the e sup N method which has proven to be successful in predicting transition in two- and three-dimensional boundary layers. When transition occurs in a low disturbance environment, the e sup N method provides a viable design tool for transition prediction and LFC in both 2-D and 3-D subsonic/supersonic flows. This is true for transition dominated by either TS, crossflow, or Goertler instability. If Goertler/TS or crossflow/TS interaction is present, the e sup N will fail to predict transition. However, there is no evidence of such interaction at low amplitudes of Goertler and crossflow vortices.

Malik, Mujeeb R.↗

NASA NTRS1991

Thermocouple-Signal-Conditioning Circuit

Thermocouple-signal-conditioning circuit acting in conjunction with thermocouple, exhibits electrical behavior of voltage in series with resistance. Combination part of input bridge circuit of controller. Circuit configured for either of two specific applications by selection of alternative resistances and supply voltages. Includes alarm circuit detecting open circuit in thermocouple and provides off-scale output to signal malfunctions.

Simon, Richard A.↗

NASA NTRS1991

Analysis of interior noise ground and flight test data for advanced turboprop aircraft applications

Interior noise ground tests conducted on a DC-9 aircraft test section are described. The objectives were to study ground test and analysis techniques for evaluating the effectiveness of interior noise control treatments for advanced turboprop aircraft, and to study the sensitivity of the ground test results to changes in various test conditions. Noise and vibration measurements were conducted under simulated advanced turboprop excitation, for two interior noise control treatment configurations. These ground measurement results were compared with results of earlier UHB (Ultra High Bypass) Demonstrator flight tests with comparable interior treatment configurations. The Demonstrator is an MD-80 test aircraft with the left JT8D engine replaced with a prototype UHB advanced turboprop engine.

Simpson, M. A.↗

NASA NTRS1989

Sensor technology for smart structures

Advanced aerospace structures are discussed that will very likely be fabricated with integral sensors, actuators, and microprocessors for monitoring and dynamic control of configuration. The concept of 'smart structures' integrates fiber-optic sensor technology with advanced composite materials, whereby the optical fibers are embedded in a composite material and provide internal sensing capability for monitoring parameters which are important for the safety, performance, and reliability of the material and the structure. Along with other research facilities, NASA has initiated a cooperative program to design, fabricate, and test composite trusses, tubes, and flat panels with embedded optical fibers for testing and developing prototype smart structures. It is shown that fiber-optic sensor technology can be combined with advanced material and structure concepts to produce a new class of materials with internal sensors for health monitoring of structures.

Rogowski, R. S.↗

NASA NTRS1992

An alternate method for achieving temperature control in the -130 C to 75 C range

Thermal vacuum testing often requires temperature control of chamber shrouds and heat exchangers within the -130 C to 75 C range. There are two conventional methods which are normally employed to achieve control through this intermediate temperature range: (1) single-pass flow where control is achieved by alternately pulsing hot gaseous nitrogen (GN2) and cold LN2 into the feed line to yield the setpoint temperature; and (2) closed-loop circulation where control is achieved by either electrically heating or LN2 cooling the circulating GN2 to yield the setpoint temperature. A third method, using a mass flow ratio controller along with modulating control valves on GN2 and LN2 lines, provides excellent control but equipment for this method is expensive and cost-prohibitive for all but long-term continuous processes. The single-pass method provides marginal control and can result in unexpected overcooling of the test article from even a short pulse of LN2. The closed-loop circulation method provides excellent control but requires an expensive blower capable of operating at elevated pressures and cryogenic temperatures. Where precise control is needed (plus or minus 2 C), single-pass flow systems typically have not provided the precision required, primarily because of overcooling temperature excursions. Where several individual circuits are to be controlled at different temperatures, the use of expensive cryogenic blowers for each circuit is also cost-prohibitive, especially for short duration of one-of-a-kind tests. At JPL, a variant of the single-pass method was developed that was shown to provide precise temperature control in the -130 C to 75 C range while exhibiting minimal setpoint overshoot during temperature transitions. This alternate method uses a commercially available temperature controller along with a GN2/LN2 mixer to dampen the amplitude of cold temperature spikes caused by LN2 pulsing. The design of the GN2/LN2 mixer, the overall control system configuration, the operational procedure, and the prototype system test results are described.

Johnson, Kenneth R.↗

NASA NTRS1992

Comparison ofdvanced turboprop interior noise control ground and flight test data

Interior noise ground tests conducted on a DC-9 aircraft test section are described. The objectives were to study ground test and analysis techniques for evaluating the effectiveness of interior noise control treatments for advanced turboprop aircraft, and to study the sensitivity of the ground test results to changes in various test conditions. Noise and vibration measurements were conducted under simulated advanced turboprop excitation, for two interior noise control treatment configurations. These ground measurement results were compared with results of earlier UHB (Ultra High Bypass) Demonstrator flight sts with comparable interior treatment configurations. The Demonstrator is an MD-80 test aircraft with the left JT8D engine replaced with a prototype UHB advanced turboprop engine.

Simpson, Myles A.↗