Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design Verification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Space Construction Automated Fabrication Experiment Definition Study (SCAFEDS), part 3. Volume 3: Requirements

The performance, design and verification requirements for the space Construction Automated Fabrication Experiment (SCAFE) are defined. The SCAFE program defines, develops, and demonstrates the techniques, processes, and equipment required for the automatic fabrication of structural elements in space and for the assembly of such elements into a large, lightweight structure. The program defines a large structural platform to be constructed in orbit using the space shuttle as a launch vehicle and construction base.

Source record↗

Total main rotor isolation system analysis

Requirements, preliminary design, and verification procedures for a total main rotor isolation system at n/rev are presented. The fuselage is isolated from the vibration inducing main rotor at one frequency in all degrees of freedom by four antiresonant isolation units. Effects of parametric variations on isolation system performance are evaluated.

Sankewitsch, V.↗

Flight test evaluation of a digital controller used in a VTOL automatic approach and landing system

As part of the NASA Langley Research Center's effort to develop technology for VTOL operation in the air transportation system in the late 1980's and beyond, research has been conducted aimed at developing digital controller design procedures. This paper describes the verification of one design procedure by the flight evaluation of an advanced digital control algorithm. The control algorithm, operating at 10 iterations per second, follows step guidance commands with zero steady state error and thus provides an autotrim capability for the nonlinear vehicle. Changes in vehicle dynamics are accounted for using a gain scheduling technique. This control algorithm is combined with sensor filters, a trajectory generator, and a closed loop guidance algorithm to form a VTOL autoland system. A CH-47 tandem rotor helicopter which contains a set of sensors, onboard digital flight computers and electro-hydraulic actuators is used in the evaluation. All software, except input-output routines, is coded in FORTRAN using floating point arithmetic and executed in the flight computer. This autoland system is exercised by automatically flying straight-in descending decelerating trajectories typical of VFR manual approaches to a predetermined landing pad.

Downing, D. R.↗

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗

The application of aerodynamic uncertainties in the design of the entry trajectory and flight control system of the space shuttle orbiter

The process used in the application of aerodynamic uncertainties for the design and verification of the Space Shuttle Orbiter Entry Flight Control System is presented. The uncertainties were used to help set center of gravity, angle of attack and dynamic pressure lateral control divergence parameter as well as C sub n sub beta dynamic were instrumental in setting these placards.

Gamble, J. D.↗

Electrophoretic purification of cells in space - Evaluation of results from STS-3

The procedure and results of Electrophoresis Equipment Verification Test, designed to examine electrophoretic behavior of animal cells is suspension more concentrated than possible on earth and flown on the Shuttle flight STS-3, were discussed. Ground-based laboratory values of electrophoretic mobilities of a mixture of human and rabbit aldehyde-fixed red blood cells (RBC) were compared with those recorded at 11 minute intervals on the Shuttle STS-3. RBC migration and separation observed through photographic records were not as expected. However, cell mobilities and migrating band profiles were consistent with the results of laboratory simulation experiments. It was concluded that zero G electrophoresis of very high concentrations (1 x 10 to the 9th) is possible and similar to electrophoresis of normal cell concentrations on earth.

Sarnoff, B. E.↗

Some real-time simulation applications to Space Shuttle approach and landing design and test

In the present discussion of the roles played by real time, man-in-the-loop engineering simulation in the development of NASA Space Shuttle approaches and landings, attention is given to the function of the simulator as a design and verification tool. Aspects of the problem posed by Shuttle landings, and the difficulties involved in this problem's quantification, are noted. Recent results of control system studies for pitch axis control, using fixed- and motion-base simulators, are discussed.

Law, H. G., III↗

Verification of computer-aided designs of traveling-wave tubes utilizing novel dynamic refocusers and graphite electrodes for the multistage depressed collector

A computational procedure for the design of TWT-refocuser-MDC systems was used to design a short dynamic refocusing system and highly efficient four-stage depressed collector for a 200-W, 8- to 18-GHz, TWT. The computations were carried out with advanced, multidimensional computer programs which model the electron beam as a series of disks of charge and follow their trajectories from the RF input of the TWT, through the slow-wave structure and refocusing section, to their points of impact in the depressed collector. Secondary emission losses in the MDC were treated semi-quantitatively by injecting a representative beam of secondary electrons into the MDC analysis at the point of impact of each primary beam. A comparison of computed and measured TWT and MDC performance showed very good agreement. The electrodes of the MDC were fabricated from a particular form of isotropic graphite that was selected for its low secondary electron yield, ease of machinability, and vacuum properties. This MDC was tested (at CW) for more than 1000 hr with negligible degradation in TWT and MDC performances.

Ramins, P.↗

Verification of an improved computational design procedure for TWT-dynamic refocuser-MDC systems with secondary electron emission losses

A computational procedure for the design of TWT-refocuser-MDC systems was used to design a short 'dynamic' refocusing system and highly efficient four-stage depressed collector for a 200-W 8-18-GHz TWT. The computations were carried out with advanced multidimensional computer programs which model the electron beam as a series of disks of charge and follow their trajectories from the RF input of the TWT, through the slow-wave structure and refocusing section, to their points of impact in the depressed collector. Secondary emission losses in the MDC were treated semiquantitatively by injecting a representative beam of secondary electrons into the MDC analysis at the point of impact of each primary beam. A comparison of computed and measured TWT and MDC performance showed very good agreement. The electrodes of the MDC were fabricated from a particular form of isotropic graphite that was selected for its low secondary electron yield, thermal expansion characteristics, ease of machinability and vacuum properties. This MDC was tested at CW for more than 1000 h with negligible degradation in TWT and MDC performances.

Ramins, P.↗

N-ROSS: The dynamics and control issues

The Navy Remote Ocean Sensing System (N-ROSS) Dynamic Stability Study team concluded that the frozen April 1985 design was viable and contained no show stoppers, although it was also clear from the study results that the configuration required further optimization. While the frozen N-ROSS configuration used has since been superceded, and the vehicle is now under competitive procurement, several other results remain from the study that will have lasting value to the N-ROSS program. The importance of constructing an integrated simulation, to serve as a design and verification aid, has been clearly established. The two team approach to the study afforded the Navy a higher degree of confidence in the results than could have been accomplished by a single simulation, and the approach led to results that highlighted subtleties in the model and simulation development that surely would have been overlookded without the benefit of an independent companion simulation with which to compare it.

Lindberg, Robert E.↗

Orbital Spacecraft Consumables Resupply System (OSCRS). Volume 2: Study results

The objective was to establish an earth storable fluids tanker concept which satisfies the initial resupply requirements for the Gamma Ray Observatory (GRO) for reasonable front end (design, development, verification) cost while providing growth potential for foreseeable future earth storable resupply mission requirements. The achievement of these objectives becomes possible with the development of a modularized tanker concept which is a hybrid of a dedicated GRO tanker and a generic earth storable propellant tanker.

Source record↗

Structural Margins Assessment Approach

A general approach to the structural design and verification used to determine the structural margins of the space vehicle elements under Marshall Space Flight Center (MSFC) management is described. The Space Shuttle results and organization will be used as illustrations for techniques discussed. Given also are: (1) the system analyses performed or to be performed by, and (2) element analyses performed by MSFC and its contractors. Analysis approaches and their verification will be addressed. The Shuttle procedures are general in nature and apply to other than Shuttle space vehicles.

Ryan, Robert S.↗

Design considerations for advanced multi-polarisation SAR

System design and verification of an airborne imaging radar (AIR) system are discussed. Issues of importance to multipolarization systems (e.g., mutual coherence and amplitude balance between channels) are emphasized. Methods of detecting and correcting channel imbalances are discussed, and AIR test results are presented.

Klein, J. D.↗

Practices in Adequate Structural Design

Structural design and verification of space vehicles and space systems is a very tricky and awe inspiring business, particularly for manned missions. Failures in the missions with loss of life is devastating personally and nationally. The scope of the problem is driven by high performance requirements which push state-of-the-art technologies, creating high sensitivites to small variations and uncertainties. Insurance of safe, reliable flight dictates the use of sound principles, procedures, analysis, and testing. Many of those principles which were refocused by the Space Shuttle Challenger (51-L) accident on January 26, 1986, and the activities conducted to insure safe shuttle reflights are discussed. The emphasis will be focused on engineering, while recognizing that project and project management are also key to success.

Ryan, Robert S.↗

The development of test beds to support the definition and evolution of the Space Station Freedom power system

Since the beginning of the Space Station Freedom Program (SSFP), the Lewis Research Center (LeRC) and the Rocketdyne Division of Rockwell International have had extensive efforts underway to develop test beds to support the definition of the detailed electrical power system design. Because of the extensive redirections that have taken place in the Space Station Freedom Program in the past several years, the test bed effort was forced to accommodate a large number of changes. A short history of these program changes and their impact on the LeRC test beds is presented to understand how the current test bed configuration has evolved. The current test objectives and the development approach for the current DC Test Bed are discussed. A description of the test bed configuration, along with its power and controller hardware and its software components, is presented. Next, the uses of the test bed during the mature design and verification phase of SSFP are examined. Finally, the uses of the test bed in operation and evolution of the SSF are addressed.

Soeder, James F.↗

Laser Transmitter Module (LTM) for LITE

In Dec. 1991 TITAN SPECTRON successfully completed its six year effort to design, build, space qualify, test, and deliver the Laser Transmitter Module (LTM) for NASA LaRC's LITE program. The delivered LTM is a three color Q-switched flashlamp pumped Nd:YAG laser that is described as the first true world-class lidar in space. The preliminary design and verification tests results were first presented at the 14th International Laser Radar Conference (ILRC) in 1988. This paper describes not only the delivered product but also the verification and space qualification processes that resulted in the world's first space qualified high powered laser system for environmental exploration from space. Video of the laser operating in a Class 100 clean room and subsystems undergoing 10 G vibration tests will provide a vivid illustration of the key elements that separate a space qualified system from its laboratory counterpart. Flight laser performance measurements form the baseline in post-delivery test results to be presented at this conference.

Chang, John↗

Safety

Software requirements, design, implementation, verification and validation, and especially management are affected by the need to produce safe software. This paper discusses the changes in the software life cycle that are necessary to ensure that software will execute without resulting in unacceptable risk. Software is being used increasingly to monitor and control safety-critical processes in which a run-time failure or error could result in unacceptable losses such as death, injury, loss of property, or environmental harm. Examples of such processes maybe found in transportation, energy, aerospace, basic industry, medicine, and defense systems.

Leveson, Nancy G.↗