SEARCH · Search NASA

Results for “ENGINES - COMPRESSION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Enhanced, continuous, liquid-liquid extraction and in-situ separation of volatile fatty acids from fermentation broth

In 2018 alone, the US landfilled 35.3 million tons of food waste, about 24% of the total landfilled mass. In addition to the negative impacts landfills have demonstrated on the environment and human health, some states have begun to outlaw or dissuade the disposal of food waste and sewage sludge into landfills altogether. An urgent need has thus been created for the development of digestion processes like anaerobic digestion (AD) and arrested methanogenesis (AM) to convert food waste into valuable chemical products. Unfortunately, the buildup of volatile fatty acids (VFAs) during these processes eventually halts the reaction, and energy efficient methodologies for VFA removal are critical for the operation of fermenters. Additionally, VFAs themselves can serve as valuable chemical precursors, and recently AD processes have been modified to increase VFA production during fermentation. However, even with significant research over the past three decades, the separation of VFAs from the fermenter broth has remained expensive. Moreover, the separation of these VFAs from the fermenter broth may cost up to 50% of the entire process budget, hindering the widespread commercial adoption of AD and AM. Here we present a novel liquid-liquid extraction process termed CLEANS (Continuous Liquid-liquid Extraction And iN-situ Separation) as a highly efficient method for continuously separating VFAs from a real fermentation broth solely under gravity. Our optimized process (using an aqueous broth feed pH of 2.5, tri-noctylamine as an extractant, and a 10:1 ratio of aqueous broth to organic extractant), achieved a VFA distribution constant K D = 44.5 ± 7.9, a single-pass recovery = 81.3 ± 2.5%, and an extraction factor = 8.1 ± 0.3. These KD values are over an order of magnitude higher than what has been previously reported for comparable processes. A high aqueous-to-organic flowrate ratio, enabled for the first time by CLEANS, was found to be particularly crucial for achieving optimal extraction. Our separation process demonstrates excellent reproducibility and potential for scalability. The economic and environmental implications of this work are briefly discussed.

42 ENGINEERING↗

DOE OSTI2024

Shock-driven three-fluid mixing with various chevron interface configurations

When a shock wave crosses a density interface, the Richtmyer–Meshkov instability causes perturbations to grow. Richtmyer–Meshkov instabilities arise from the deposition of vorticity from the misaligned density and pressure gradients at the shock front. In many engineering applications, microscopic surface roughness will grow into multi-mode perturbations, inducing mixing between the fluid on either side of an initial interface. Applications often have multiple interfaces, some of which are close enough to interact in the later stages of instability growth. In this study, we numerically investigate the mixing of a three-layer system with periodic zigzag (or chevron) interfaces, calculating the dependence of the width and mass of mixed material on properties such as the shock timing, chevron amplitude, multi-mode perturbation spectrum, density ratio, and shock mach number. The multi-mode case is also compared with a single-mode perturbation. The Flash hydrodynamic code is used to solve the Euler equations in three dimensions with adaptive grid refinement. Key results include a significant increase in mixed mass when changing from a single-mode to a multi-mode perturbation on one of the interfaces. The mixed width is mainly sensitive to the density ratio and chevron amplitude, whereas the mixed mass also depends on the multi-mode spectrum. In conclusion, steeper initial perturbation spectra have lower mixed mass at early times but a greater mixed mass after the reflected shock transits back across the layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Multilevel Switched-Capacitor AC–DC Step-Down Rectifier for Wireless Charging With Reduced Conduction Loss and Harmonic Content

In this paper, a wireless charging architecture employing a multilevel switched-capacitor (MSC) AC-DC rectifier is investigated. The proposed MSC rectifier features a multilevel design which is scalable to accommodate different power ratings and load ranges. The topology showcases advantages for wireless power transfer (WPT) systems in terms of compactness, efficiency, impedance tunability, and harmonic attenuation. The single-stage active topology is capable of varying its low-distortion staircase input voltage to tune the wireless power transfer system for high system-wide efficiency. A 7-level, 20 W prototype is used to verify the WPT loading and loss analysis. The prototype operates at 150 kHz with up to 3:1 step-down conversion ratio to an output voltage of 5.0 V. The experimental peak DC-to-DC efficiency is 93.8% and the rectifier peak efficiency is 98.3%. As a result. the rectifier demonstrates low waveform distortion and high efficiency across many WPT loading conditions, solidifying its place as a strong candidate for wireless power applications.

42 ENGINEERING↗

DOE OSTI2020

The Installation of Direct Water-Cooling Systems to Reduce Cooling Energy Requirements for High-Performance Computing Centers

A large cluster of High-Performance Computing (HPC) equipment at the Lawrence Livermore National Laboratory in California was retrofitted with an Asetek cooling system. The Asetek system is a hybrid scheme with water-cooled cold plates on high-heat-producing components in the information technology (IT) equipment, and with the remainder of the heat being removed by conventional air-cooling systems. In order to determine energy savings of the Asetek system, data were gathered and analyzed two ways: using top-down statistical models, and bottom-up engineering models. The cluster, “Cabernet”, rejected its heat into a facilities cooling water loop which in turn rejected the heat into the same chilled water system serving the computer-room air handlers (CRAHs) that provided the air-based cooling for the room. Because the “before” and “after” cases both reject their heat into the chilled water system, the only savings is due to reduction in CRAH fan power. The top-down analysis showed a 4% overall energy savings for the data center (power usage effectiveness (PUE) —the ratio of total data center energy to IT energy— dropped from 1.60 to 1.53, lower is better); the bottom-up analysis showed a 3% overall energy savings (PUE from 1.70 to 1.66) and an 11% savings for the Cabernet system by itself (partial PUE of 1.51). Greater savings, on the order of 15-20%, would be possible if the chilled water system was not used for rejecting the heat from the Asetek system. About 37% of the heat from the Cab system was rejected to the cooling water, lower than at other installations.

Earni, Shankar↗

DOE OSTI2024

High-Fidelity Modeling of a Type-5 Wind Turbine Gearbox (Intern Poster) [Poster]

Type-5 wind turbines are unique in their use of a permanent magnet synchronous generator, as well as their use of a hydraulic torque converter. This architecture presents an opportunity to provide steady and grid-ready energy without the need for a power converter. With infrastructure continuity and reliability being an important topic amongst renewable energies, researchers have been prompted to further investigate the benefits of type-5 turbines’ unique electromechanical configuration on stable electricity generation. Researchers involved in the WindSG project, SG standing for synchronous generator, are aiming to model a type-5 turbine using Real Time Digital Simulation (RTDS) to evaluate its efficacy in the grid. RSCAD, the software run on the RTDS, comes pre-loaded with electrical and electromechanical components to help simulate electrical generation and grid conditions. However, within this repertoire there is a lack of a component to represent a gearbox with high-fidelity. Within RSCAD’s case studies, the gearbox is often represented simply by a gear ratio value. This presented the task of developing a high-fidelity gearbox model in RSCAD for use in the larger RTDS type-5 wind turbine model. This poster describes a method of developing a lumped parameter mathematical model to represent a planetary-parallel-parallel gearbox in RSCAD for use in RTDS.

17 WIND ENERGY↗

DOE OSTI2024

High-Fidelity Modeling of a Type-5 Wind Turbine Gearbox (Intern Technical Presentation) (Poster)

Type-5 wind turbines are unique in their use of a permanent magnet synchronous generator, as well as their use of a hydraulic torque converter. This architecture presents an opportunity to provide steady and grid-ready energy without the need for a power converter. With infrastructure continuity and reliability being an important topic amongst renewable energies, researchers have been prompted to further investigate the benefits of type-5 turbines’ unique electromechanical configuration on stable electricity generation. Researchers involved in the WindSG project, SG standing for synchronous generator, are aiming to model a type-5 turbine using Real Time Digital Simulation (RTDS) to evaluate its efficacy in the grid. RSCAD, the software run on the RTDS, comes pre-loaded with electrical and electromechanical components to help simulate electrical generation and grid conditions. However, within this repertoire there is a lack of a component to represent a gearbox with high-fidelity. Within RSCAD’s case studies, the gearbox is often represented simply by a gear ratio value. This presented the task of developing a high-fidelity gearbox model in RSCAD for use in the larger RTDS type-5 wind turbine model. This presentation describes a method of developing a lumped parameter mathematical model to represent a planetary-parallel-parallel gearbox in RSCAD for use in RTDS.

17 WIND ENERGY↗

DOE OSTI2021

Design of Novel Flash Ironmaking Reactors for Greatly Reduced Energy Consumption and CO2 Emissions

The development of a novel ironmaking technology based on fine iron ore concentrate in a flash reactor is summarized. The design of potential industrial reactors for flash ironmaking based on the computational fluid dynamics technique is described. Overall, this simulation work has shown that the size of the reactor used in the novel flash ironmaking technology (FIT) can be quite reasonable vis-à-vis the blast furnaces. A flash reactor of 12 m diameter and 35 m height with a single burner operating at atmospheric pressure would produce 1.0 million tons of iron per year. The height can be further reduced by either using multiple burners, preheating the feed gas, or both. The computational fluid dynamics (CFD)-based design of potential industrial reactors for flash ironmaking pointed to a number of features that should be incorporated. The flow field should be designed in such a way that a larger portion of the reactor is used for the reduction reaction but at the same time excessive collision of particles with the wall must be avoided. Further, a large diameter-to-height ratio that still allows a high reduction degree should be used from the viewpoint of decreased heat loss. This may require the incorporation of multiple burners and solid feeding ports.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Magnesium Technology 2020

Magnesium and its alloys are being investigated widely for applications that require extraordinarily high strength-to-weight ratio, vibration damping, electromagnetic shielding, reduction in carbon footprint, sustainability improvements, and low toxicity. In the past decade or so, this drive has led to increased adoption of magnesium and its alloys in everyday products and it is no longer regarded as an esoteric material. The overarching goal of its widespread adoption and replacement of conventional materials such as steel and aluminum alloys has been restricted because of the cost of the material, limited sources of primary material, alloying constraints, high chemical reactivity, and challenges associated with its plasticity. Researchers, scientists, engineers, and economists from industry, government agencies and laboratories, and academic institutions alike are actively developing roadmaps for next-generation products and addressing these challenges as quickly as possible through unique and innovative methods. The TMS Magnesium Committee has been actively involved in providing a platform to these entities for disseminating the latest information, developments, and cutting-edge research and development, and showcasing the latest research and development trends related to magnesium and its alloys through the Magnesium Technology Symposium, which takes place every year at the TMS Annual Meeting. This proceedings volume retains the essence of this longstanding tradition. The twenty-first volume in the series, Magnesium Technology 2020, is the proceedings of the Magnesium Technology Symposium held during the 149th TMS Annual Meeting & Exhibition in San Diego, CA, February 23–27, 2020. The volume captures commentaries and papers from 15 different countries. The papers have been categorized systematically based on topics pertaining to magnesium production, casting and solidification, thermomechanical processing, deformation mechanisms, modeling, corrosion, and applications. The symposium began with keynote sessions that featured several distinguished invited speakers from government organizations and academia, who provided their perspectives on the state of the art, goals, and opportunities in magnesium alloy research and development. Dr. Carlos Tomé from Los Alamos National Laboratory, U.S. Department of Energy, discussed 3D characterization of mechanical twins across grain boundaries. This was followed by a talk on hierarchically structured ultrafine-grained magnesium alloys by Dr. Rajiv Mishra from the University of North Texas, USA, who presented an example of using friction stir additive manufacturing for implementing such microstructures at a component level. Dr. Mark Horstemeyer from Liberty University, USA, presented an overview of fatigue modeling to capture the corrosion-fatigue behavior of magnesium alloys. The final talk in this session was presented by Dr. Bin Jiang from Chongqing University, China, who presented a novel extrusion approach for achieving high-strength magnesium alloy plates.

Jordon, J. Brian↗

DOE OSTI2023

A reacting multiphase computational flow model for 2,3-butanediol synthesis in industrial-scale bioreactors

The microbe, Zymomonas mobilis, can efficiently convert sugars to 2,3 butanediol (BDO), an important intermediate for downstream chemical products, only in a well-controlled microaerated environment. However, controlling oxygen distribution in industrial-scale bioreactors is challenging, and at-scale BDO production is hard to optimize using traditional engineering methods. This study takes a step towards addressing this problem through a computational model for reacting multiphase flows in large-scale bioreactors. A phenomenological metabolic model was first developed and validated against experiments, and then it was coupled to a multiphase computational fluid dynamics (CFD) solver using a subcycling algorithm for simulating long conversion times (~30 hours). Large-scale (~500 m 3 ) bubble column simulations using this coupled approach demonstrated a 25% improvement in BDO yield with low sparging rates (0.002 m/s) and low height-to-diameter ratio (0.875) compared to a baseline bubble column (35 m height, 5 m diameter) with a superficial gas velocity of 0.06 m/s.

09 BIOMASS FUELS↗

DOE OSTI2022

Numerical and experimental investigation of the flame kernel growth in a methane/air mixture near the lean flammability limit

Lean combustion has the potential to improve the thermal efficiency of spark-ignition engines, but it faces the significant challenge of increased cycle-to-cycle variation due to low mixture reactivity and unstable flame dynamics. Computational fluid dynamics (CFD) employing predictive models can guide engine design and optimize operating strategies for lean combustion. However, ignition and combustion models have rarely been validated at fuel-lean conditions, and a fundamental understanding of the early flame kernel growth process is also lacking for a successful sub-model development. Here, the present study develops a numerical simulation framework used to investigate early flame kernel growth in methane/air mixtures. A nanosecond-pulsed discharge (NPD) approach is employed to effectively decouple the flame kernel growth from the electrical discharge due to their difference in timescales, and equivalence ratios near the experimentally measured lean flammability limit (LFL) are selected to focus on challenging mixture conditions. Three numerical investigations, such as the choice of turbulence modeling, grid size, and grid control strategies, are examined to match both LFL and flame kernel structure measured from experiments. It is demonstrated that a quasi-direct numerical simulation (QDNS) with a fixed grid embedding of 10 μm can predict the LFL as φ CFD =0.61 and match the displacement speed of the kernel’s boundary marked in schlieren images. To predict the LFL and flame kernel shape, a fine grid (Δ≤12.5 μm) is needed to capture the consumption of formaldehyde (CH 2 O) in kernel’s reaction branches attached to the anode, and adaptive mesh refinement is replaced with the fixed embedding due to loss of simulation accuracy. Also, it is found that a large-eddy simulation (LES) using the Dynamic Structure model is not suitable for the NPD-induced flame kernel simulation because artificial sub-grid turbulent kinetic energy induced by shock dynamics alters the flow velocity calculation, resulting in divergence of LES from QDNS. Lastly, the simulation well matches the experimental data for the flame kernel evolution in three mixture conditions (φ = 0.7, 0.61, 0.55), showing toroidal flame kernel expansion and flame kernel growth/extinction.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2026

Bioproduction, bioprotection, and biocontainment in multi-kingdom microbial systems with 3D spatial control

Engineered living materials (ELMs) are a class of hybrid materials that include engineered microbes encapsulated by a polymer matrix. The biotic and abiotic components define the ELMs design space and can be altered to improve performance and function. While current synthetic materials in the field display robust biocompatibility with both native and engineered living systems, we have a limited understanding of how to leverage three-dimensional (3D) form factors to spatially organize and control microbial dynamics within the material. Motivated by this knowledge gap, we employed extrusion-based 3D printing to fabricate multi-kingdom hydrogel constructs for the encapsulation of both single and multi-kingdom microbial systems. Core–shell cubic constructs enabled the spatial organization of a constitutive multi-kingdom system of levodopa (L-DOPA)-producing E. coli and betaxanthins (BXN)-producing S. cerevisiae. This spatial organization in 3D materials can introduce precise control over bioproduction, bioprotection, and biocontainment features that are critical to the efficacy of current ELMs. The relative spatial organization of the organisms, as well as the surface area-to-volume ratio were investigated to determine how these design elements impact microbial behavior (metabolite production, growth, expression, and cell distribution) over time. We demonstrated that F127-bis-urethane methacrylate (F127-BUM) core–shell geometries enable the hierarchical 3D printing of multi-kingdom constructs, offering customizable control over bioproduction, bioprotection, and biocontainment. With the optimization of these core–shell structures for continuous bioproduction, these ELMs could be deployed as compact and sustainable bioreactors in remote environments.

additive manufacturing↗

DOE OSTI2024

Rheology of bi-disperse dense fiber suspensions

While significant progress has been made in the modeling and simulation of uniform fiber suspensions, no existing model has been validated for industrially-relevant concentrated suspensions containing fibers of multiple aspect ratios. In the present work, we investigate bi-disperse suspensions with two fiber populations in varying aspect ratios in a steady shear flow using direct numerical simulations. Moreover, we measure the suspension viscosity by creating a controlled length bidispersity for nylon fibers suspended in a Newtonian fluid. Here the results showed good agreement between the experimentally measured and numerically predicted viscosity for bi-disperse suspensions. The ratio between the aspect ratio of large to small fibers (size ratio) and the volume fraction of large fibers (composition) in bi-disperse systems strongly affected the rheological behavior of the suspension. The increment of relative viscosity associated with size ratio and composition can be explained by the decrease in the maximum flowable limit or jamming volume fraction. Moreover, the relative viscosity of bi-disperse suspensions collapses, when plotted against the reduced volume fraction, demonstrating the controlling influence of the jamming fraction in bi-disperse fiber suspensions.

42 ENGINEERING↗

DOE OSTI2022

Transient creep‐fatigue crack growth in creep‐brittle materials: Application to Alloy 718

Abstract This study presents incremental finite element computations of creep‐fatigue crack growth in Alloy 718 at in air. Alloy 718 is representative of creep‐brittle materials, in which viscoplastic deformation is restricted near the tip of a growing crack. The computations predict crack growth using a unique combination of an irreversible cohesive zone formulation and a strain gradient viscoplastic material model based on the Kocks–Mecking formulation. Cohesive zone damage parameters are estimated using sustained loading and constant‐amplitude cyclic loading experiments. Computations of crack extension under three different waveforms containing overloads all predict post‐overload retardation. The amount of retardation depends strongly on the overload ratio, consistent with experiments in the literature using similar waveforms. Analysis of the crack‐tip fields demonstrates retardation is associated with unloading in the highly deformed material near the advancing crack tip. Dynamic recovery and geometrically necessary dislocations are shown to significantly influence post‐overload crack extension.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Experimental and computational studies of load ratio effect on fatigue crack growth rates in Alloy 709 at elevated temperatures

Abstract Experimental testing and finite element simulations of fatigue crack growth were performed in austenitic 20Cr‐25Ni (Alloy 709) steel at different load ratios and elevated temperatures. The experimental tests were performed using compact tension specimens, and crack growth rates were measured at stress intensity factors ranging between 5 and 35 MPa√m. Fractographic analysis using scanning electron microscopy indicated crack surface roughness and secondary cracking depending on testing temperature and load ratio. Finite element simulations of fatigue crack growth were performed to compute plasticity‐induced crack opening loads and predict crack growth rates. Predictions of fatigue crack growth rates using finite element simulations were performed using the computed crack‐tip opening loads, and they are shown to match well the experimental measurements.

Engineering↗

DOE OSTI2024

Optimal load attachment of a deeply embedded ring anchor in clay

A Deeply Embedded Ring Anchor (DERA) system has been developed as a cost-effective solution for mooring arrays of floating offshore wind turbines (FOWTs) to the seabed. The DERA boasts several key features, including its versatility in various soil types, compact size, compatibility with diverse mooring systems, multi-line potential, and robust performance even under unintentional loading conditions. While prior preliminary studies have provided valuable insights into how the DERA can enhance cost-effectiveness by offering a high load capacity, these studies have predominantly focused on optimizing anchor performance under translational horizontal and vertical loading. However, to design the DERA optimally, we must also consider its ability to handle inclined loading conditions in addition to lateral and axial loadings. Due to its shorter length compared to a conventional caisson, the DERA has less resistance to moments, making it more sensitive to horizontal load capacity and the optimal load attachment depth concerning load angle. For this reason, our study introduces an analytical approach to evaluate the effects of inclined loading on anchor performance, utilizing the previously validated upper bound plastic limit analysis (PLA) method. In investigating the optimal load attachment of the DERA, this paper conducts a parametric study to analyze how factors such as load attachment depth, anchor aspect ratio, and load inclination affect the DERA’s load capacity. Our findings indicate that PLA can serve as a valuable analytical tool for assessing the ultimate load capacity of the DERA, particularly under inclined loading conditions.

42 ENGINEERING↗

DOE OSTI2025

Data for Influence of Particle Size on NIR Spectroscopic Characterization of Sorghum Biomass for the Biofuel Industry

NIR spectroscopy is a rapid and accurate green technology for high-throughput biomass characterization, including sorghum ( Sorghum bicolor ), a promising energy crop for the biofuel industry. This study assessed the influence of particle size on NIR spectroscopic analysis (wavelength range: 867–2535 nm) of sorghum biomass composition. Grown under field conditions, a total of 113 types of genetically diverse sorghum accessions were dried, ground, and sieved (<250, 250–600, 600–850, and > 850 µm particle size) for developing partial least square regression (PLSR) prediction models for moisture, ash, extractive, glucan, xylan, acid-soluble lignin (ASL), acid-insoluble lignin (AIL), and total lignin (ASL + AIL). Overall, smaller particle sizes provided better model performance, while no single particle size provided the best performance for all the selected components. With only 9 selected bands and 4 latent variables (LVs), the best PLSR model was obtained for moisture with particle size of 600–850 µm with the square root of the coefficient of determination (R) of 0.85, the ratio of prediction to deviation (RPD) of 2.2, and the root mean square error (RMSE) of 0.46 % in external validation. Similar model performances were also obtained for ash, extractive, glucan, and xylan. This study showed that size reduction could effectively improve NIR spectroscopic analysis for lipid-producing sorghum biomass for the biofuel industry.

Biomass Analytics↗

DOE OSTI2026

Injection Locking Dynamics of Oscillation Loop with Saturable Gain

We analytically derive and experimentally verified the injection-locking range and phase-noise suppression ratio of an oscillation loop with saturable gain, establishing a general and straightforward approach for analyzing injection locking dynamics.

Xi, Zichen [ORNL]↗

DOE OSTI2022

Preliminary Thermal-hydraulics and Selected Safety Analysis for Holos-Quad Reactor Design

This report presents thermal hydraulics and safety analyses of the 10 MWe Holos-Quad micro-reactor design developed by HolosGen LLC. These analyses were executed under steady-state and station black-out (SBO) transient conditions using the System Analysis Module (SAM), with a focus on ensuring peak fuel temperatures do not exceed the safety thresholds of 1,250°C for steady state normal operating conditions and 1,600°C for transient conditions. For steady-state temperature predictions, a coupled 1D fluid-to-3D solid heat conduction methodology was used. The steady-state simulations included a model of the central core region where power peaking occurs to predict the maximum steady-state fuel temperature, and a coarse-mesh full-core model to provide the initial condition for the consequent transient SBO decay heat removal simulation. The maximum fuel temperature predicted from the central core region simulations under the normal operating condition was 1,222°C, which is below the design limit 1,250°C. To simulate a SBO transient, a full core model was necessary because of the non-axial symmetric core design and heat loss from the outer core structures to the environment. To reduce the required computational costs, a novel scaled subassembly approach was used to model the full core domain. With the full core steady-state temperature distribution provided as the initial condition, the passive decay heat removal of the core was simulated with the scaled subassembly full core model under SBO transient conditions. This analysis showed that the peak fuel temperatures of the Holos-Quad core remained below their steady-state values during the transient, therefore much lower than the safety limit 1,600°C. This is mainly due to the large thermal inertia of the graphite matrix, relatively low power density, and the large surface-to-volume-ratio of the core. The preliminary analyses presented in this report confirm the inherent safety of the Holos-Quad micro-reactor thermal-hydraulics design, as the peak fuel temperatures under both normal and off-normal operational conditions remain within design and safety limits.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗