Search NASA⌕ Search

SEARCH · Search NASA

Results for “Edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Improved Woodward's panel method for calculating edge suction forces

A new technique to improve Woodward's (1968) unified subsonic and supersonic panel method is described. The pressure prediction is improved based on a new two-dimensional theory. The method used by Lan (1977) is then used to calculate the leading-edge and side-edge suction forces by direct use of the predicted pressure distribution. The method is applicable to both subsonic and supersonic flow. It is shown that the improved Woodward panel method is capable of accurately predicting leading-edge and side-edge suction forces in subsonic and supersonic flow. Therefore, the method can be used not only to predict the vortex lift of complex planforms through the method of suction analogy, but also to calculate some lateral-directional stability derivatives.

Lan, C. E.↗
NASA NTRS1979

Exploratory study of the effects of wing-leading-edge modifications on the stall/spin behavior of a light general aviation airplane

Configurations with full-span and segmented leading-edge flaps and full-span and segmented leading-edge droop were tested. Studies were conducted with wind-tunnel models, with an outdoor radio-controlled model, and with a full-scale airplane. Results show that wing-leading-edge modifications can produce large effects on stall/spin characteristics, particularly on spin resistance. One outboard wing-leading-edge modification tested significantly improved lateral stability at stall, spin resistance, and developed spin characteristics.

Source record↗
NASA NTRS1978

A computer program for calculating aerodynamic characteristics of low aspect-ratio wings with partial leading-edge separation

The necessary information for using a computer program to predict distributed and total aerodynamic characteristics for low aspect ratio wings with partial leading-edge separation is presented. The flow is assumed to be steady and inviscid. The wing boundary condition is formulated by the Quasi-Vortex-Lattice method. The leading edge separated vortices are represented by discrete free vortex elements which are aligned with the local velocity vector at midpoints to satisfy the force free condition. The wake behind the trailing edge is also force free. The flow tangency boundary condition is satisfied on the wing, including the leading and trailing edges. The program is restricted to delta wings with zero thickness and no camber. It is written in FORTRAN language and runs on CDC 6600 computer.

Mehrotra, S. C.↗
NASA NTRS1979

Design, analysis, and tests of a shuttle-type heat-pipe-cooled leading edge

A one-half scale heat-pipe-cooled leading edge model was designed and fabricated to verify feasibility and performance of a full-scale Phase B shuttle orbiter design. Model performance was investigated experimentally by radiant heating and aerothermal tests and analytically by using a simple technique which predicts heat pipe start-up from the frozen state and also predicts transient and steady-state thermal behavior. Analytical results agree well with experimental results for start-up and steady-state heat pipe operation. The results indicate that variations in angle of attack and roll orientation had a negligible effect on heat pipe performance. The heat pipes effectively isothermalized the leading edge, and reduced peak temperatures to levels compatible with the use temperatures of superalloys. Results of these tests demonstrated the durability of the heat-pipe-cooled leading edge in withstanding earth-entry thermal and mechanical loads and indicate that the use of heat pipes in leading edge structures is a reliable concept for fully reusable hypersonic cruise and space transportation systems.

Camarda, C. J.↗
NASA NTRS1980

The effects of leading edge modifications on the post-stall characteristics of wings

An investigation of the effects of leading edge modifications on the post-stall characteristics of two rectangular planform wings in a series of low speed wind tunnel tests is presented. Abrupt discontinuities in the leading edge shape of the wings were produced by placing a nose glove over a portion of the span or by deflecting sections of a segmented leading edge flap. Six component balance data, oil flow visualization photographs, and pressure distribution measurements were obtained, and tests made to study the development of flow separation at stall on small scale planform wing models. Results of oil flow visualization tests at and beyond stall showed the formation of counter-rotating swirl patterns on the upper surface of the '2-D' and '3-D' wings, and results of a numerical lifting line technique applied to wings with leading edge modifications are included.

Winkelmann, A. E.↗
NASA NTRS1980

Full-scale wind-tunnel investigation of the effects of wing leading-edge modifications on the high angle-of-attack aerodynamic characteristics of a low-wing general aviation airplane

The paper presents the results of a recent investigation to determine the effects of wing leading-edge modifications on the high angle-of-attack aerodynamic characteristics of a low-wing general aviation airplane in the Langley Full-Scale Wind Tunnel. The investigation was conducted to provide aerodynamic information for correlation and analysis of flight-test results obtained for the configuration. The wind-tunnel investigation consisted of force and moment measurements, wing pressure measurements, flow surveys, and flow visualization studies utilizing a tuft grid, smoke and nonintrusive mini-tufts which were illuminated by ultra-violet light. In addition to the tunnel scale system which measured overall forces and moments, the model was equipped with an auxiliary strain-gage balance within the left wing panel to measure lift and drag forces on the outer wing panel independent of the tunnel scale system. The leading-edge modifications studied included partial- and full-span leading-edge droop arrangements as well as leading-edge slats.

Johnson, J. L., Jr.↗
NASA NTRS1980

Trailing edge noise from hovering rotors

A method has been developed to predict the high frequency broadband noise due to the interaction of convecting turbulent eddies with the trailing edges of a hovering rotor. The trailing edge noise from each blade was modeled as point dipole noise with spanwise loading corrections. This point dipole approximation was checked by applying the concept to a stationary airfoil in a moving medium with excellent results. In order to estimate the strength of the point dipole, the trailing edge noise theory of Amiet was used. The method was applied specifically to blade boundary layer turbulence and compared to incident atmospheric turbulence noise. The results indicate that the relative importance of these two mechanisms is related to the magnitudes of the intensity and of the length scales of the inflow and boundary layer turbulence. The results tend to fall below some available experimental data indicating that in those experiments other broadband noise sources were stronger than boundary layer-trailing edge noise. The approach which was developed is also applicable to other blade-turbulence interaction mechanisms such as local stall and tip noise.

Kim, Y. N.↗
NASA NTRS1981

Trailing edge noise prediction from measured surface pressures

Trailing edge (TE) noise is investigated for the case of a two-dimensional airfoil embedded in a uniform low Mach number flow, and the usefulness of several TE noise theories is examined by applying them to the measured data. The TE noise spectra and directivity are quantitatively determined for the case of a high Reynolds number and a fully turbulent boundary layer. Parameters include angle of attack, flow velocity and TE bluntness. Evanescent wave theories by Chase (1975) and Chandiramani (1974) are compared to the present results and show good agreement. Agreement of the near field pressure scatter phenomenon analysis with measurements implies that the basic assumptions used in the analysis are correct, i.e., the turbulent boundary layer (TBL) flow passes the trailing edge into the wake region. No hydrodynamic wake shedding activity is confirmed for the two-sided TBL flow, and a method incorporating the principles of the coherent output power method is used to determine the sound field. The near field edge scatter model is found to not only establish optimum sizing of edge treatment for noise control, but also to separate and identify the scattered field from the incident hydrodynamic field.

Brooks, T. F.↗
NASA NTRS1955

Investigation of Porous Gas-Heated Leading-Edge Section for Icing Protection of a Delta Wing

A tip section of a delta wing having an NACA 0004-65 airfoil section and a 600 leading-edge sweepback was equipped with a porous leading-edge section through which hot gas was 'bled for anti-icing. Heating rates for anti-icing were determined for a wide range of icing conditions. The effects of gas flow through the porous leading-edge section on airfoil pressure distribution and drag in dry air were investigated. The drag increase caused by an ice formation on the unheated airfoil was measured for several icing conditions. Experimental porous surface- to free-stream convective heat-transfer coefficients were obtained in dry air and compared with theory. Adequate icing protection was obtained at all icing conditions investigated. Savings in total gas-flow rate up to 42 percent may be obtained with no loss in anti-icing effectiveness by sealing half the upper-surface porous area. Gas flow through the leading-edge section had no appreciable effect on airfoil pressure distribution. The airfoil section drag increased slightly (5-percent average) with gas flow through the porous surface. A heavy glaze-ice formation produced after 10 minutes of icing caused an increase in section drag coefficient of 240 percent. Experimental convective heat-transfer coefficients obtained with hot-gas flow through the porous area in dry air and turbulent flow were 20 to 30 percent lower than the theoretical values for a solid surface under similar conditions. The transition region from laminar to turbulent flow moved forward as the ratio of gas velocity through the porous surface to air-stream velocity was increased.

Bowden, Dean T.↗
NASA NTRS1981

Helicopter rotor trailing edge noise

A two dimensional section of a helicopter main rotor blade was tested in an acoustic wind tunnel at close to full-scale Reynolds numbers to obtain boundary layer data and acoustic data for use in developing an acoustic scaling law and testing a first principles trailing edge noise theory. Results were extended to the rotating frame coordinate system to develop a helicopter rotor trailing edge noise prediction. Comparisons of the calculated noise levels with helicopter flyover spectra demonstrate that trailing edge noise contributes significantly to the total helicopter noise spectrum at high frequencies. This noise mechanism is expected to control the minimum rotor noise. In the case of noise radiation from a local blade segment, the acoustic directivity pattern is predicted by the first principles trailing edge noise theory. Acoustic spectra are predicted by a scaling law which includes Mach number, boundary layer thickness and observer position. Spectrum shape and sound pressure level are also predicted by the first principles theory but the analysis does not predict the Strouhal value identifying the spectrum peak.

Schlinker, R. H.↗
NASA NTRS1982

Effects of wing-leading-edge modifications on a full-scale, low-wing general aviation airplane: Wind-tunnel investigation of high-angle-of-attack aerodynamic characteristics

Wing-leading-edge modifications included leading-edge droop and slat configurations having full-span, partial-span, or segmented arrangements. Other devices included wing-chord extensions, fences, and leading-edge stall strips. Good correlation was apparent between the results of wind-tunnel data and the results of flight tests, on the basis of autorotational stability criterion, for a wide range of wing-leading-edge modifications.

Newsom, W. A., Jr.↗
NASA NTRS1981

Edge delamination in angle-ply composite laminates, part 5

A theoretical method was developed for describing the edge delamination stress intensity characteristics in angle-ply composite laminates. The method is based on the theory of anisotropic elasticity. The edge delamination problem is formulated using Lekhnitskii's complex-variable stress potentials and an especially developed eigenfunction expansion method. The method predicts exact orders of the three-dimensional stress singularity in a delamination crack tip region. With the aid of boundary collocation, the method predicts the complete stress and displacement fields in a finite-dimensional, delaminated composite. Fracture mechanics parameters such as the mixed-mode stress intensity factors and associated energy release rates for edge delamination can be calculated explicity. Solutions are obtained for edge delaminated (theta/-theta theta/-theta) angle-ply composites under uniform axial extension. Effects of delamination lengths, fiber orientations, lamination and geometric variables are studied.

Wang, S. S.↗
NASA NTRS1982

The digital step edge

The facet model was used to accomplish step edge detection. The essence of the facet model is that any analysis made on the basis of the pixel values in some neighborhood has its final authoritative interpretation relative to the underlying grey tone intensity surface of which the neighborhood pixel values are observed noisy samples. Pixels which are part of regions have simple grey tone intensity surfaces over their areas. Pixels which have an edge in them have complex grey tone intensity surfaces over their areas. Specially, an edge moves through a pixel only if there is some point in the pixel's area having a zero crossing of the second directional derivative taken in the direction of a non-zero gradient at the pixel's center. To determine whether or not a pixel should be marked as a step edge pixel, its underlying grey tone intensity surface was estimated on the basis of the pixels in its neighborhood.

Haralick, R. M.↗
NASA NTRS1983

Red edge measurements for remotely sensing plant chlorophyll content

The feasibility of using the wavelength of the maximum slope of the red edge of leaf reflectance spectra, Lambda(re), as an indication of plant chlorophyll status was examined in the laboratory for single leaves of several species. Lambda(re) for each sample was determined by derivative reflectance spectroscopy. A high positive correlation was found between Lambda(re) and leaf chlorophyll content for all species, although there were some differences in the quantitative nature of the relationship for plants of different types. The position of the red edge was found to be unaffected by simulated change in ground cover, but multiple leaf layers produced a shift in its position. Appropriate spectral measurements and processing for obtaining useful information from the red edge are discussed, and the potential of the red edge in relation to other spectral measurements is considered.

Horler, D. N. H.↗
NASA NTRS1984

Advanced leading edge thermal-structure concept. Direct bond reusable surface insulation to a composite structure

An advanced leading-edge concept was analyzed using the space shuttle leading edge system as a reference model. The comparison indicates that a direct-bond system utilizing a high temperature (2700 F) fibrous refractory composite insulation tile bonded to a high temperature (PI/graphite) composite structure can result in a weight savings of up to 800 lb. The concern that tile damage or loss during ascent would result in adverse entry aerodynamics if a leading edge tile system were used is addressed. It was found from experiment that missing tiles (as many as 22) on the leading edge would not significantly affect the basic force-and-moment aerodynamic coefficients. Additionally, this concept affords a degree of redundancy to a thermal protection system in that the base structure (being a composite material) ablates and neither melts nor burns through when subjected to entry heating in the event tiles are actually lost or damaged during ascent.

Riccitiello, S. R.↗
NASA NTRS1984

Edge analyzing properties of center/surround response functions in cybernetic vision

The ability of center/surround response functions to make explicit high resolution spatial information in optical images was investigated by performing convolutions of two dimensional response functions and image intensity functions (mainly edges). The center/surround function was found to have the unique property of separating edge contrast from shape variations and of providing a direct basis for determining contrast and subsequently shape of edges in images. Computationally simple measures of contrast and shape were constructed for potential use in cybernetic vision systems. For one class of response functions these measures were found to be reasonably resilient for a range of scan direction and displacements of the response functions relative to shaped edges. A pathological range of scan directions was also defined and methods for detecting and handling these cases were developed. The relationship of these results to biological vision is discussed speculatively.

Jobson, D. J.↗
NASA NTRS1982

VORCOR: A computer program for calculating characteristics of wings with edge vortex separation by using a vortex-filament and-core model

A computer code base on an improved vortex filament/vortex core method for predicting aerodynamic characteristics of slender wings with edge vortex separations is developed. The code is applicable to camber wings, straked wings or wings with leading edge vortex flaps at subsonic speeds. The prediction of lifting pressure distribution and the computer time are improved by using a pair of concentrated vortex cores above the wing surface. The main features of this computer program are: (1) arbitrary camber shape may be defined and an option for exactly defining leading edge flap geometry is also provided; (2) the side edge vortex system is incorporated.

Pao, J. L.↗
NASA NTRS1983

Edge discrimination as applied to Thematic Mapper data

An evaluation of suitable edge discrimination techniques and their application to image segmentation is reported. From an analysis of Thematic Mapper Simulator data, it is concluded that segmentation by automated edge discrimination is a valuable technique which can be used in the development of per-field classifiers. A Laplacian convolution operator appears to be the most cost-effective high-pass filter. Spatial frequency domain filtering is more versatile in its ability to enhance different edge types. A simple global gray value threshold can produce good edge discrimination from an enhanced image which may be improved by using a local thresholding technique. A gap-fill postprocessing technique is necessary for useful segmentation. Gradient and other directionally dependent techniques are unsuitable for segmentation.

Hall, J. R.↗