Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flexural testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Rotating Balances Used for Fluid Pump Testing

Marshall Space Flight Center has developed and demonstrated two direct read force and moment balances for sensing and resolving the hydrodynamic loads on rotating fluid machinery. These rotating balances consist of a series of stainless steel flexures instrumented with semiconductor type, unidirectional strain gauges arranged into six bridges, then sealed and waterproofed, for use fully submerged in degassed water at rotational speeds up to six thousand revolutions per minute. The balances are used to measure the forces and moments due to the onset and presence of cavitation or other hydrodynamic phenomena on subscale replicas of rocket engine turbomachinery, principally axial pumps (inducers) designed specifically to operate in a cavitating environment. The balances are inserted into the drive assembly with power to and signal from the sensors routed through the drive shaft and out through an air-cooled twenty-channel slip ring. High frequency data - balance forces and moments as well as extensive, flush-mounted pressures around the rotating component periphery - are acquired via a high-speed analog to digital data acquisition system while the test rig conditions are varied continuously. The data acquisition and correction process is described, including the in-situ verifications that are performed to quantify and correct for known system effects such as mechanical imbalance, "added mass," buoyancy, mechanical resonance, and electrical bias. Examples of four types of cavitation oscillations for two typical inducers are described in the laboratory (pressure) and rotating (force) frames: 1) attached, symmetric cavitation, 2) rotating cavitation, 3) attached, asymmetric cavitation, and 4) cavitation surge. Rotating and asymmetric cavitation generate a corresponding unbalanced radial force on the rotating assembly while cavitation surge generates an axial force. Attached, symmetric cavitation induces no measurable force. The frequency of the forces can be determined a priori from the pressure environment while the magnitude of the hydrodynamic force is proportional to the pressure unsteadiness.

Skelley, Stephen↗

Effect of Aluminum Titanate (Al 2 TiO 5 ) Doping on the Mechanical Performance of Solid Oxide Fuel Cell Ni-YSZ Anode

The mechanical behavior of un-doped and 1–10 wt.% aluminum titanate doped NiO-YSZ anodes was evaluated in the oxidized and reduced state of the material. Sample bars 25 × 5 × 2 mm were fabricated and tested in a three-point bending apparatus and statistical analyzes of the collected data were performed. A remarkable enhancement of the flexural strength was found both for the reduced and oxidized state of the material when compared to the un-doped samples. In both cases, the development of a secondary phase was observed proportional to the doping amount of aluminum titanate. Morphological analysis along with preliminary phase identification and suspected mechanisms for strength enhancement are presented and discussed.

25 ENERGY STORAGE↗

Why Firn Quakes

Snow dampens sounds, but anecdotal reports concisely describe audible propagating collapse events—firnquakes—in Antarctic and Arctic snowfields. We propose combining granular and continuum mechanics to form a testable theory for conditioning, triggering, and propagation of firnquakes consistent with scarce data. A central condition for collapse events is unconsolidated firn at depth. As firn grains compact, stresses are transmitted along force chains which carry the overburden and transition into a continuous medium by pressure sintering. This granular legacy creates solid-like supports of denser layers that keep the material below unconsolidated. Dynamic amplification triggers local brittle failure of the supports, which induces a cascade of collapse propagation. Using bulk density from ice cores as proxy for stiffness, we find the flexural wave speed by collapsing supports matches the recorded firnquake velocities on the order of 100 m/s. Our theory is to be tested in firn sheets and other compacting granular materials.

Voigtländer, A. [Lawrence Berkeley National Labora↗

Investigation of the Effect of In-Plane Fiber Waviness in Composite Materials through Multiple Scales of Testing and Finite Element Modeling

Defects in materials can reduce strengths and lifetimes of manufactured parts. The number of possible defects increases with the complexity inherent in composite materials. The wind industry uses composite wind turbine blades in which the manufacturing process induces a number of defects. In order for the wind industry to continue sustainable expansion, the effects of defects must be better understood. In-plane (IP) fiber waviness is the focus of this work. The three main parts of this work include testing on the coupon level, modeling on the coupon level, and testing of beams in four-point bending (with and without defects). The coupon level testing includes partial IP waves, similar to those in manufactured parts, rather than full width IP waves. This allows investigation into complex interactions and varying failure mechanisms caused by the fiber misalignment gradient. Partial waves are also modeled to both validate testing as well as to increase robustness of a previously developed progressive damage modeling method. Lastly, a sandwich beam test specimen for testing in 4-point bending is developed to investigate the effects of fiber waviness in both tension and compression when loaded in flexure.

36 MATERIALS SCIENCE↗

The impact of remote manipulator structural dynamics on Shuttle on-orbit flight control

The performance of the Space Shuttle on-orbit flight control system during payload operations with the remote manipulator system is described. The changing mass and inertia distribution associated with payload manipulation can have a significant effect on the control authority provided by the orbiter's reaction control jets. Commanded payload motion and jet firings can excite significant flexure in the orbiter/manipulator/payload structure. These effects combine to stress the control capabilities of the flight control system. Data from recent flight tests is presented to illustrate these effects.

Sargent, D. G.↗

Polyimide Matrix composites: Polyimidesulfone/LARC-TPI (1:1) blend

Polyimide matrix composites were fabricated from unidirectional unsized AS-4 carbon fiber and a doped 1:1 blend of two polyimides: benzophenone dianhydride-3,3'-diamino diphenylsulfone (PISO2) and benzophenone dianhydride-3,3'-diamino benzophenone (LARC-TPI). To enhance melt flow properties, the molecular weight of the PISO2 was controlled by end-capping with phthalic anhydride and addition of 5 percent by weight p-phenylene diamine-phthalic anhydride bisamic acid dopant. Prepreg was drum-wound using a diglyme slurry comprised of the soluble polyamideacid of PISO2, the soluble bisamideacid of the dopant, and the insoluble imidized LARC-TPI powder. Melt flow studies with a rotary rheometer and parallel plate plastometer on neat resin and prepreg helped develop an optimum cure cycle. Composite mechanical properties at room and elevated temperatures, dry and moisture-saturated, were evaluated, including short beam shear strength and flexure, tensile, shear, and compression properties. Two 18 in. x 24 in. skin-stringer panels were fabricated, one of which was tested in compression to failure.

Johnston, Norman J.↗

Development of a precision, six-axis laboratory dynamometer

This paper describes the design, fabrication, test, and operation of a unique six axis force/torque dynamometer The specimen table used to hold components under test is supported in a full six axis kinematic mount. Support struts fabricated from high strength steel with special integral two axis flexures link the specimen table to the load cell transducers. Realtime force/torque coordinate transform, root mean squared calculation, and data averaging, and color six axis display with controllable scaling are provided by a specially programmed desktop computer. The extensive structural analysis and design optimization required to obtain a stiff, well damped, lightweight structure is described in detail. Geometric optimization of the kinematic mount and fabrication details of the struts are also described.

P. J. Champagne↗

Effects of Impact Damage in Midplane Asymmetric Sandwich Composites

Several structural sandwich composites arc in service on military and commercial aerospace vehicles, however, these components have been limited to secondary structures partly because the impact damage and damage tolerance of these composites have not been extensively characterized. To improve durability, safety, and life cycle performance of PMCs while reducing maintenance costs, combined analysis, and test methods that provide a means of predicting critical engineering properties after impact damage of the structure, must be developed. A key enabling technology here is the establishment of the correlation between the impact test results conducted in the laboratory and the mechanics-based phenomenological solutions. This research was undertaken to investigate the compression and flexural properties following low velocity impact of a nomex/phenolic honeycomb core, fiberglass/epoxy facesheet, midplane asymmetric sandwich composite. One facesheet (thin side) was composed of two plies of the fiberglass/epoxy (0/90), while the other facesheet (thick side) was composed of four plies (0/90/0/90) of fiberglass/epoxy. Due to the differences in facesheet thickness, impact damage was separately induced on the thick side as well as the thin side. The compression and flexural strength properties for each damage arrangement were compared using different levels of impact energy ranging from 0 to 452 Joules. In all cases, higher impact energy resulted in decreased compression and flexural strength. Impact on the thin side showed slightly more retention of compression strength at low impact levels, whereas higher residual compressive strength was observed from impact on the thick side at higher impact levels. Different facesheet thicknesses or midplane asymmetry, played an important role in the flexural strength, however, low velocity impact on the both the thick and thin fiberglass/epoxy facesheet side showed an almost linear loss of flexural strength to saturation.

Meador, Michael↗

Equibiaxial Flexure Strength of a Superfine-Grained Nuclear Graphite

The strength of advanced graphite is reported in accordance with ASTM D7846-16 using a two-parameter Weibull distribution for uniaxial strength testing. The rule of thumb for Weibull distributions is to use a minimum of 30 strength measurements to have a high level of confidence in the Weibull characteristic strength and the Weibull modulus. These large sample sets for statistical confidence are easily obtained for as-manufactured graphite, but determination of the Weibull two-factor parameters on graphite that has been exposed to neutron irradiation is nearly impossible due to irradiation testing restraints on specimen size and space limitations in test reactors for the accommodation of specimens. These restrictions have resulted in irradiation programs that use sub-sized specimens to measure uniaxial strength change, but the specimen geometries still hinder the number of replicate specimens for each irradiation condition. In contrast, this work used an advanced ceramic standard, ASTM C1499-05, as the foundation for equibiaxial strength testing of a superfine-grained nuclear graphite to investigate the irradiation-induced strength change and any changes to the two-parameter Weibull distribution. The goal was to investigate the effect of specimen size on the two-parameter Weibull distribution parameters in support of the small specimens and geometry desired for irradiation. A study of the effect of a reduced sample population was also undertaken to investigate the reliability of using the two-parameter Weibull distribution to study changes to the materials properties caused by neutron irradiation damage. The results of this work suggest that these equibiaxial specimens would be ideal for statistically significant studies of the effects of irradiation on the Weibull characteristic strength (but not the modulus) and for providing a method for surveillance specimen campaigns for future operating commercial reactors.

Campbell, Anne↗

Signal and power roll ring testing update

The development of the roll ring as a long-life, low-torque alternative to the slip ring is discussed. A roll ring consists of one or more circular flexures captured by their own spring force in the annular space between two concentric conductors or contact rings. The advantages of roll rings over other types of electrical transfer devices are: extremely low drag torque, high transfer efficiencies in high-power configurations, extremely low wear debris generation, long life, and low weight for high-power applications.

Smith, Dennis W.↗

Sintering and Fracture Behavior of Plasma-sprayed Thermal Barrier Coatings

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. There is a need to characterize the fundamental sintering and fracture behavior of the current ZrO2-(7 to 8)wt%Y2O3 coating, in order to fully take advantage of the coating capability. In addition, a thorough evaluation of the coating behavior and temperature limits will be useful for more accurately assessing the benefit gained from future advanced coating systems. In this study, the sintering behavior of plasma-sprayed ZrO2-8wt%Y2O3 coatings was systematically investigated as a function of temperature and time using a dilatometer in the temperature range of 1200-1500 C. The coating sintering kinetics obtained by dilatometry were compared with the coating thermal conductivity increase kinetics, determined by a steady-state laser heat-flux testing approach, under high temperature and thermal gradient sintering conditions. The mode I, mode II, and mixed mode I-mode II fracture behavior of as-processed and sintering-annealed coatings was determined in asymmetric flexure loading at ambient and elevated temperatures in order to evaluate the coating sintering effects on the fracture envelope of K(sub I) versus K(sub II). The coating thermal conductivity cyclic response associated with the interface delamination of the coating systems under simulated engine heat-flux conditions will be discussed in conjunction with the sintering and fracture testing results.

Zhu, Dongming↗

Advanced Active-Magnetic-Bearing Thrust-Measurement System

An advanced thrust-measurement system utilizes active magnetic bearings to both (1) levitate a floating frame in all six degrees of freedom and (2) measure the levitation forces between the floating frame and a grounded frame. This system was developed for original use in measuring the thrust exerted by a rocket engine mounted on the floating frame, but can just as well be used in other force-measurement applications. This system offers several advantages over prior thrust-measurement systems based on mechanical support by flexures and/or load cells: The system includes multiple active magnetic bearings for each degree of freedom, so that by selective use of one, some, or all of these bearings, it is possible to test a given article over a wide force range in the same fixture, eliminating the need to transfer the article to different test fixtures to obtain the benefit of full-scale accuracy of different force-measurement devices for different force ranges. Like other active magnetic bearings, the active magnetic bearings of this system include closed-loop control subsystems, through which the stiffness and damping characteristics of the magnetic bearings can be modified electronically. The design of the system minimizes or eliminates cross-axis force-measurement errors. The active magnetic bearings are configured to provide support against movement along all three orthogonal Cartesian axes, and such that the support along a given axis does not produce force along any other axis. Moreover, by eliminating the need for such mechanical connections as flexures used in prior thrust-measurement systems, magnetic levitation of the floating frame eliminates what would otherwise be major sources of cross-axis forces and the associated measurement errors. Overall, relative to prior mechanical-support thrust-measurement systems, this system offers greater versatility for adaptation to a variety of test conditions and requirements. The basic idea of most prior active-magnetic-bearing force-measurement systems is to calculate levitation forces on the basis of simple proportionalities between changes in those forces and changes in feedback-controlled currents applied to levitating electromagnetic coils. In the prior systems, the effects of gap lengths on fringing magnetic fields and the concomitant effects on magnetic forces were neglected. In the present system, the control subsystems of the active magnetic bearings are coupled with a computer-based automatic calibration system running special-purpose software wherein gap-length-dependent fringing factors are applied to current and magnetic-flux-based force equations and combined with a multipoint calibration method to obtain greater accuracy.

Imlach, Joseph↗

Design, analysis and testing of a parallel-kinematic high-bandwidth XY nanopositioning stage

This paper presents the design, analysis, and testing of a parallel-kinematic high-bandwidth XY nanopositioning stage driven by piezoelectric stack actuators. The stage is designed with two kinematic chains. In each kinematic chain, the end-effector of the stage is connected to the base by two symmetrically distributed flexure modules, respectively. Each flexure module comprises a fixed-fixed beam and a parallelogram flexure serving as two orthogonal prismatic joints. With the purpose to achieve high resonance frequencies of the stage, a novel center-thickened beam which has large stiffness is proposed to act as the fixed-fixed beam. The center-thickened beam also contributes to reducing cross-coupling and restricting parasitic motion. To decouple the motion in two axes totally, a symmetric configuration is adopted for the parallelogram flexures. Based on the analytical models established in static and dynamic analysis, the dimensions of the stage are optimized in order to maximize the first resonance frequency. Then finite element analysis is utilized to validate the design and a prototype of the stage is fabricated for performance tests. According to the results of static and dynamic tests, the resonance frequencies of the developed stage are over 13.6 kHz and the workspace is 11.2 μm × 11.6 μm with the cross-coupling between two axes less than 0.52%. It is clearly demonstrated that the developed stage has high resonance frequencies, a relatively large travel range, and nearly decoupled performance between two axes. For high-speed tracking performance tests, an inversion-based feedforward controller is implemented for the stage to compensate for the positioning errors caused by mechanical vibration. The experimental results show that good tracking performance at high speed is achieved, which validates the effectiveness of the developed stage.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Low loss, flexible, lightweight corporate RF feed system for SAR antenna application

Mechanical and electrical efficiency constraints imposed by the SEASAT-A synthetic aperture radar antenna posed difficult design problems. After consideration of available standard cable and waveguide systems, it was determined that an optimum design could be obtained from a suspended substrate RF feed system. Size and mechanical flexibility constraints forced the design of a flexible, suspended substrate section capable of 180-degree flexure. Original design goal for insertion loss over power division was 1 db; measured results indicated 0.6 db maximum across the band. Multipactor testing of system components indicated system breakdown capability in excess of 4 kW compared to a specification input maximum of 1500 W.

Schiavone, F.↗

Fracture analysis of radial scientific instrument module registration fittings of the space telescope

Various pieces of the registration fittings for the Radial Scientific instrument (SI) module of the Space Telescope were examined from a fracture mechanics point of view and deemed to be fail-safe or else have had maximum allowable flaw sizes specified for them. The results of these analyses are summarized in tabular form. In many instances the applied stress levels were so low that the threshold stress intensity factor range was never reached. In most of the others the allowable flaw sizes were large enough to be detected by visual inspection. However, for some parts, such as the flexures connecting the aluminum cover to the ball retainer in the fitting at point A, the flaw sizes were rather small. Eddy current tests are capable of detecting flaws of this size (0.022 inches x 0.1 inches), so for those which have been so tested these small flaws should represent no danger of going undetected. In every instance approximations were made to err on the conservative side. These were pointed out in the discussions of the analyses for each fitting. One conservative approximation that was not mentioned, however, is the fact that retardation was not included in the crack propagation computations.

Springfield, C. W., Jr.↗

Various Analyses of Structures and Systems Pertaining to Optical Communications

The Optical Communications Group intends to experiment with a 2 by 2 meter Fresnel lens to determine its likelihood as an alternative to focusing mirrors for optical communications. The lens was delivered in four sections. A support structure was required for the lens in order to hold the four sections in a single flat plane with an adjustable degree angle. In order to use the 200-in. Hale telescope for optical communications purposes, an optical filter membrane must used to pass the communications wavelength while blocking sunlight wavelengths. This filter must withstand wind gusts of up to 50 miles per hour. Stress analysis predicts that the membrane will survive with a safety factor greater than two. The methods used were verified by pressure testing the material. Mechanical and thermodynamic analyses were performed on a simple Golay cell in order to optimize its dimensions for best performance. Flexures are examined as an inexpensive alternative to traditional methods for kinematically constraining a 1.5-meter spherical mirror.

Petersen, Collin W.↗

Synthesis and Characterization of Zr2SC Ceramics

MAX-phase Zr{sub 2}SC ceramics were synthesized by hot pressing mixtures containing ZrH{sub 2}, carbon or ZrC, and ZrS{sub 2}, WS{sub 2}, or FeS{sub 2} as sulfur sources. The Zr{sub 2}SC synthesized with FeS{sub 2} had a typical MAX-phase laminated structure, good thermal shock resistance, thermal stability to 2100 C, and were readily machineable. The flexural strength was about 250 MPa up to 800 C. The thermal expansion coefficient was 8.8 x 10{sup -6}/C in the 25-2000 C-temperature range, thermal conductivity was 38 W/m-K at 100 C and about 30 W/m-K at 1100 C, and specific heat at temperatures from 100 to 1100 C ranged from 0.4 to 0.5 kJ/kg C. Load-deflection curves exhibited plastic deformation from RT to 2066 C. The sample deflection at fracture demonstrated significant dependence on temperature with a minimum at 1510 C. In arc heater testing at 2150 C for 23 s, the material developed an adherent, protective scale.

36 MATERIALS SCIENCE↗

Graphite/polyimide composites with improved toughness

Studies were performed to determine the toughness characteristics of composites prepared from modified addition-type polyimides, using Celion 6000 graphite fiber as the reinforcement. The polyimides were prepared from aromatic diamines containing flexibilizing ether connecting groups. The composite flexural and short beam shear strengths were determined at room temperature and elevated temperatures. Composite toughness was evaluated using 10 deg off axis tensile tests and double cantilever beam fracture tests at room temperature. The effects of the flexibilized resin structure on composite mechanical properties, toughness characteristics, and thermo-oxidative stability are discussed.

Delvigs, Peter↗