Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flow separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Suggested future directions in high-speed transition experimental research

Historical developments in the area of high-speed experimental transition research are outlined, and future directions in this area as determined by the panel membership are listed. The directions include measurement and modeling of initial disturbance fields, both in ground facilities and flight, for all modes; development of advanced high-speed instrumentation for disturbance field measurements, measurements of the details of receptivity in multitudinous flows; further development and use of high-speed quiet tunnels; stability and transition studies for multitudinous flows; detailed studies of the transitional region for boundary layers, free flows, vortices separated flows, corner flows, etc.; and studies of flow-chemistry effects on transition phenomena. Applied research such areas as the physics of perforated-surface suction stabilization and the resolution of anomalies in the existing high-speed database is also suggested.

Bushnell, Dennis↗
NASA NTRS1997

Flight Demonstration of a Shock Location Sensor Using Constant Voltage Hot-Film Anemometry

Flight tests have demonstrated the effectiveness of an array of hot-film sensors using constant voltage anemometry to determine shock position on a wing or aircraft surface at transonic speeds. Flights were conducted at the NASA Dryden Flight Research Center using the F-15B aircraft and Flight Test Fixture (FTF). A modified NACA 0021 airfoil was attached to the side of the FTF, and its upper surface was instrumented to correlate shock position with pressure and hot-film sensors. In the vicinity of the shock-induced pressure rise, test results consistently showed the presence of a minimum voltage in the hot-film anemometer outputs. Comparing these results with previous investigations indicate that hot-film anemometry can identify the location of the shock-induced boundary layer separation. The flow separation occurred slightly forward of the shock- induced pressure rise for a laminar boundary layer and slightly aft of the start of the pressure rise when the boundary layer was tripped near the airfoil leading edge. Both minimum mean output and phase reversal analyses were used to identify the shock location.

Moes, Timothy R.↗
NASA NTRS2002

Wake Closure Characteristics and Afterbody Heating on a Mars Sample Return Orbiter

Aeroheating wind-tunnel tests were conducted on a 0.028 scale model of an orbiter concept considered for a possible Mars sample return mission. The primary experimental objectives were to characterize hypersonic near wake closure and determine if shear layer impingement would occur on the proposed orbiter afterbody at incidence angles necessary for a Martian aerocapture maneuver. Global heat transfer mappings, surface streamline patterns, and shock shapes were obtained in the NASA Langley 20-Inch Mach 6 Air and CF4 Tunnels for post-normal shock Reynolds numbers (based on forebody diameter) ranging from 1,400 to 415,000, angles of attack ranging from -5 to 10 degrees at 0, 3, and 6 degree sideslip, and normal-shock density ratios of 5 and 12. Laminar, transitional, and turbulent shear layer impingement on the cylindrical afterbody was inferred from the measurements and resulted in a localized heating maximum that ranged from 40 to 75 percent of the reference forebody stagnation point heating. Comparison of laminar heating prediction to experimental measurement along the orbiter afterbody highlight grid alignment challenges associated with numerical simulation of three- dimensional separated wake flows. Predicted values of a continuum breakdown parameter revealed significant regions of non-continuum flow downstream of the flow separation at the MSRO shoulder and in the region of the reattachment shock on the afterbody. The presence of these regions suggest that the Navier-Stokes predictions at the laminar wind-tunnel condition may encounter errors in the numerical calculation of the wake shear layer development and impingement due to non-continuum effects.

Horvath, Thomas J.↗
NASA NTRS2016

Effect of Stagger on the Vibroacoustic Loads from Clustered Rockets

The effect of stagger startup on the vibro-acoustic loads that form during the end- effects-regime of clustered rockets is studied using both full-scale (hot-gas) and laboratory scale (cold gas) data. Both configurations comprise three nozzles with thrust optimized parabolic contours that undergo free shock separated flow and restricted shock separated flow as well as an end-effects regime prior to flowing full. Acoustic pressure waveforms recorded at the base of the nozzle clusters are analyzed using various statistical metrics as well as time-frequency analysis. The findings reveal a significant reduction in end- effects-regime loads when engine ignition is staggered. However, regardless of stagger, both the skewness and kurtosis of the acoustic pressure time derivative elevate to the same levels during the end-effects-regime event thereby demonstrating the intermittence and impulsiveness of the acoustic waveforms that form during engine startup.

Rojo, Raymundo↗
NASA NTRS1992

Hypersonic flows as related to the national aerospace plane

The study in the last 6 months has observed a clear evidence that the current two-equation models tend to under-predict flow separation and over-predict heat transfer rate near flow re-attachment regions. In hypersonic flow calculations, these model deficiencies appear to be even more pronounced. This is particularly true in the incapability of the model to predict the extent of the flow separation. Two major deficiencies of the current two-equation models in predicting complex hypersonic flows have been reported, i.e., under-prediction of flow separation and over-prediction of peak heat transfer rate. Two modifications to the k - epsilon model were reported and tested over a range of flows. Based on our limited study, the modified models have been found to give better agreements in both surface pressure and heat transfer predictions for several complex shock-wave boundary-layer interaction flows. However, in order to confirm our observation, more calculations will be performed in the future study covering a wider range of flows and conditions than reported here.

Kussoy, Marvin↗
NASA NTRS1977

Numerical solution of axisymmetric boattail flow fields with plume simulators

Turbulent separating flows over axisymmetric afterbody-boattail configurations with solid sting plume simulators are computed with a time-dependent finite-difference method to solve the compressible Navier-Stokes equations. The Reynolds stress terms are replaced with a two-layer eddy viscosity model including a relaxation formula to model the nonequilibrium effects of the separated flow. The mesh is alined with the boattail body through an analytic transformation which accommodates a wide variety of boattail geometries. Numerical results for a series of boattail geometries over a wide range of Reynolds number (140,000 to 140 million) are presented and, when possible, compared with experimental data or independent numerical results.

Holst, T. L.↗
NASA NTRS1983

Structure of Evaporating and Combusting Sprays: Measurements and Predictions

Complete measurements of the structure of nonevaporating, evaporating and combusting sprays for sufficiently well defined boundary conditions to allow evaluation of models of these processes were obtained. The development of rational design methods for aircraft combustion chambers and other devices involving spray combustion were investigated. Three methods for treating the discrete phase are being considered: a locally homogeneous flow (LHF) model, a deterministic separated flow (DSF) model, and a stochastic separated flow (SSF) model. The main properties of these models are summarized.

Shuen, J. S.↗
NASA NTRS1983

Measurements and predictions for nonevaporating sprays in a quiescent environment

Yule et al. (1982) have conducted a study of vaporizing sprays with the aid of laser techniques. The present investigation has the objective to supplement the measurements performed by Yule et al., by considering the limiting case of a spray in a stagnant environment. Mean and fluctuating velocities of the continuous phase are measured by means of laser Doppler anemometry (LDA) techniques, while Fraunhofer diffraction and slide impaction methods are employed to determine drop sizes. Liquid fluxes in the spray are found by making use of an isokinetic sampling probe. The obtained data are used as a basis for the evaluation of three models of the process, including a locally homogeneous flow (LHF) model, a deterministic separated flow (DSF) model, and a stochastic separated flow (SSF) model. It is found that the LHF and DSF models do not provide very satisfactory predictions for the test sprays, while the SSF model does provide reasonably good predictions of the observed structure.

Solomon, A. S. P.↗
NASA NTRS1984

The structure of evaporating and combusting sprays: Measurements and predictions

An apparatus developed, to allow observations of monodisperse sprays, consists of a methane-fueled turbulent jet diffusion flame with monodisperse methanol drops injected at the burner exit. Mean and fluctuating-phase velocities, drop sizes, drop-mass fluxes and mean-gas temperatures were measured. Initial drop diameters of 100 and 180 microns are being considered in order to vary drop penetration in the flow and effects of turbulent dispersion. Baseline tests of the burner flame with no drops present were also conducted. Calibration tests, needed to establish methods for predicting drop transport, involve drops supported in the post-flame region of a flat-flame burner operated at various mixture ratios. Spray models which are being evaluated include: (1) locally homogeneous flow (LFH) analysis, (2) deterministic separated flow (DSF) analysis and (3) stochastic separated flow (SSF) analysis.

Shuen, J. S.↗
NASA NTRS2012

Experimental Investigation of Normal Shock Boundary-Layer Interaction with Hybrid Flow Control

Hybrid flow control, a combination of micro-ramps and micro-jets, was experimentally investigated in the 15x15 cm Supersonic Wind Tunnel (SWT) at the NASA Glenn Research Center. Full factorial, a design of experiments (DOE) method, was used to develop a test matrix with variables such as inter-ramp spacing, ramp height and chord length, and micro-jet injection flow ratio. A total of 17 configurations were tested with various parameters to meet the DOE criteria. In addition to boundary-layer measurements, oil flow visualization was used to qualitatively understand shock induced flow separation characteristics. The flow visualization showed the normal shock location, size of the separation, path of the downstream moving counter-rotating vortices, and corner flow effects. The results show that hybrid flow control demonstrates promise in reducing the size of shock boundary-layer interactions and resulting flow separation by means of energizing the boundary layer.

Vyas, Manan A.↗
NASA NTRS2016

Sweeping Jet Optimization Studies

Progress on experimental efforts to optimize sweeping jet actuators for active flow control (AFC) applications with large adverse pressure gradients is reported. Three sweeping jet actuator configurations, with the same orifice size but di↵erent internal geometries, were installed on the flap shoulder of an unswept, NACA 0015 semi-span wing to investigate how the output produced by a sweeping jet interacts with the separated flow and the mechanisms by which the flow separation is controlled. For this experiment, the flow separation was generated by deflecting the wing's 30% chord trailing edge flap to produce an adverse pressure gradient. Steady and unsteady pressure data, Particle Image Velocimetry data, and force and moment data were acquired to assess the performance of the three actuator configurations. The actuator with the largest jet deflection angle, at the pressure ratios investigated, was the most efficient at controlling flow separation on the flap of the model. Oil flow visualization studies revealed that the flow field controlled by the sweeping jets was more three-dimensional than expected. The results presented also show that the actuator spacing was appropriate for the pressure ratios examined.

Melton, LaTunia Pack↗
NASA NTRS1993

Vortex developments over steady and accelerated airfoils incorporating a trailing edge jet

Computational and experimental studies are conducted to investigate the influence of a trailing edge jet on flow separation and subsequent vortex formation over steady and accelerated airfoils at high angles of attack. A computer code, employing the stream function-vorticity approach, is developed and utilized to conduct numerical experiments on the flow problem. To verify and economize such efforts, an experimental system is developed and incorporated into a subsonic wind tunnel where streamline and vortex flow visualization experiments are conducted. The study demonstrates the role of the trailing edge jet in controlling flow separation and subsequent vortex development for steady and accelerating flow at angles past the static stall angle of attack. The results suggest that the concept of the trailing edge jet may be utilized to control the characteristics of unsteady separated flows over lifting surfaces. This control possibility seems to be quite effective and could have a significant role in controlling unsteady separated flows.

Finaish, F.↗
NASA NTRS1978

Analytical studies of separated vortex flow on highly swept wings

A subsonic potential flow mathematical model of the flow past slender aerodynamic surfaces with sharp edges and separated vortex flow is reported. Comparisons with experimental data are presented for overall forces and pressure distributions for a series of thin, low aspect ratio wings, including both flat and conically cambered ones. A discussion is presented of the limitations of the current theory, and some suggestions are made as to how the theory might be improved. Details of program data input modifications for three-dimensional geometry are described in an appendix.

Kuhlman, J. M.↗
NASA NTRS1973

Prediction of space shuttle fluctuating pressure environments, including rocket plume effects

Preliminary estimates of space shuttle fluctuating pressure environments have been made based on prediction techniques developed by Wyle Laboratories. Particular emphasis has been given to the transonic speed regime during launch of a parallel-burn space shuttle configuration. A baseline configuration consisting of a lightweight orbiter and monolithic SRB, together with a typical flight trajectory, have been used as models for the predictions. Critical fluctuating pressure environments are predicted at transonic Mach numbers. Comparisons between predicted environments and wind tunnel test results, in general, showed good agreement. Predicted one-third octave band spectra for the above environments were generally one of three types: (1) attached turbulent boundary layer spectra (typically high frequencies); (2) homogeneous separated flow and shock-free interference flow spectra (typically intermediate frequencies); and (3) shock-oscillation and shock-induced interference flow spectra (typically low frequencies). Predictions of plume induced separated flow environments were made. Only the SRB plumes are important, with fluctuating levels comparable to compression-corner induced separated flow shock oscillation.

Plotkin, K. J.↗
NASA NTRS1983

A time-dependent approach for calculating steady inverse boundary-layer flows with separation

An unsteady inverse boundary-layer method is developed which can be used to calculate steady flows with separation. Two versions of Keller's box method with the Mechul function formulation developed by Cebeci (1976) are employed, depending on the complexity of the flow. The regular box is employed in regions of positive streamwise velocity component u, whereas the zigzag box is employed in regions where u becomes negative (t greater than 0). The regular box with the FLARE approximation is employed when t = 0 and u becomes negative in some region across the layer. Results of calculations show that the use of a time-dependent inverse boundary-layer method in which time is used as an iteration parameter provides a good approach in improving the accuracy of the solutions obtained from the FLARE approximation.

Cebeci, T.↗
NASA NTRS1961

Free Flight Observation of a Separated Turbulent Flow Including Heat Transfer Up to Mach 8.5

A turbulent boundary layer separated by a forward-facing step was observed on the cylindrical portion of a hemisphere-cone-cylinder test vehicle. Tip blunting, producing a shear flow, was found to induce higher pressures on the cylindrical portion than were predicted from ballistic tunnel data of unblunted projectiles. An approximate method for predicting this blunt-body pressure distribution was hypothesized. These findings, along with the hypothesis, were substantiated by a wind tunnel test of a similar body. The peak pressure ratios of the separation were smaller in magnitude than flat plate theory predicted because of the effect of the shear flow. The decrement in heating of the separated flow, relative to the corresponding attached flow, was found to compare well with the expected results.

McConnell, Dudley George↗
NASA NTRS1991

Summary of in-flight flow visualization obtained from the NASA high alpha research vehicle

A summary of the surface and off-surface flow visualization results obtained in flight on the F-18 high alpha research vehicle (HARV) is presented, highlighting the extensive 3-D vortical flow on the aircraft at angles of attack up to 50 degs. The emitted fluid technique, as well as tufts and flow cones, were used to document the surface flow. A smoke generator system injected smoke into the vortex cores generated by the forebody and leading edge extensions (LEXs). Documentation was provided by onboard still and video, by air-to-air, and by postflight photography. The surface flow visualization techniques revealed laminar separation bubbles near the forebody apex, lines of separation on the forebody and LEX, and regions of attached and separated flow on the wings and fins. The off-surface flow visualization techniques showed the path of the vortex cores on the forebody and LEX as well as the LEX vortex core breakdown location. An interaction between the forebody and LEX vortices was noted. The flow over the surfaces of the vertical tail was categorized into regions of attached, unsteady, or separated flow using flow tufts.

Fisher, David F.↗
NASA NTRS1982

Phenomenological study of subsonic turbulent flow over a swept rearward-facing step

The phenomenology of turbulent, subsonic flow over a swept, rearward-facing step was studied. Effects of variations in step height, sweep angle, base geometry, and end conditions on the 3-D separated flow were examined. The separated flow was visualized using smoke wire, oil drop, and surface tuft techniques. Measurements include surface pressure, reattachment distance and swirl angle. Results indicate: (1) model/test section coupling affects the structure of the separated flow, but spanwise end conditions do not; (2) the independence principle is evidently valid for sweep angles up to 38 deg; (3) a sweep angle/swirl angle correlation exists; and (4) base modifications can significantly reduce the reattachment distance.

Selby, G. V.↗