Search NASA⌕ Search

SEARCH · Search NASA

Results for “Flutter”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Digital-flutter-suppression-system investigations for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the project, and the development and successful use of a methodology for on-line controller performance evaluation.

Perry, Boyd, III↗
NASA NTRS1990

An experimental study of tip shape effects on the flutter of aft-swept, flat-plate wings

The effects of tip chord orientation on wing flutter are investigated experimentally using six cantilever-mounted, flat-plate wing models. Experimentally determined flutter characteristics of the six models are presented covering both the subsonic and transonic Mach number ranges. While all models have a 60 degree leading edge sweep, a 40.97 degree trailing edge sweep, and a root chord of 34.75 inches, they are subdivided into two series characterized by a higher aspect ratio and a lower aspect ratio. Each series is made up of three models with tip chord orientations which are parallel to the free-stream flow, perpendicular to the model mid-chord line, and perpendicular to the free-stream flow. Although planform characteristics within each series of models are held constant, structural characteristics such as mode shapes and natural frequencies are allowed to vary.

Dansberry, Bryan E.↗
NASA NTRS1989

Aeroelastic detuning for stability enhancement of unstalled supersonic flutter

A mathematical model is presented for analyzing the effect of aeroelastic detuning on unstalled supersonic flutter, where the detuning mechanism employed is alternate-blade structural detuning. Two alternative aerodynamic detuning methods are compared: the novel, alternate-chordwise airfoil spacing method, and the alternate circumferential airfoil spacing aerodynamic detuning. A combination of aerodynamic and structural detuning is considered. Relative flutter stability enhancements are assessed for a twelve-blade baseline rotor.

Fleeter, Sanford↗
NASA NTRS1990

Digital-flutter-suppression-system investigations for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind-tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the project, and the development and successful use of a methodology for online controller performance evaluation.

Perry, Boyd, III↗
NASA NTRS1989

Application of the CAP-TSD unsteady transonic small disturbance program to wing flutter

The application and assessment of a computer program called CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) for flutter predictions are described. Flutter calculations are presented for two thin swept-and-tapered wing planforms with well-defined modal properties. One planform is a series of 45-degree swept wings and the other planform is a clipped delta wing. Comparisons are made between the results of CAP-TSD using the linear equation and no airfoil thickness and the results obtained from a subsonic kernel function analysis. The calculations cover a Mach number range from low subsonic to low supersonic values, including the transonic range, and are compared with subsonic linear theory and experimental data. It is noted that since both wings have very thin airfoil sections, the effects of thickness are minimal.

Bennett, Robert M.↗
NASA NTRS1991

Placing Control Surfaces To Suppress Aeroelastic Flutter

Method for assigning positions of control surfaces to suppress aeroelastic flutter involves analysis of transfer of energy. Neither depends on nor prescribes specific form of control law. Assuming suitable control law available by whatever means, shows how to determine where on aircraft or airfoil control surface(s) maximally effective in suppressing flutter.

Nissim, E.↗
NASA NTRS1991

Cascade flutter analysis with transient response aerodynamics

Two methods for calculating linear frequency domain aerodynamic coefficients from a time marching Full Potential cascade solver are developed and verified. In the first method, the Influence Coefficient, solutions to elemental problems are superposed to obtain the solutions for a cascade in which all blades are vibrating with a constant interblade phase angle. The elemental problem consists of a single blade in the cascade oscillating while the other blades remain stationary. In the second method, the Pulse Response, the response to the transient motion of a blade is used to calculate influence coefficients. This is done by calculating the Fourier Transforms of the blade motion and the response. Both methods are validated by comparison with the Harmonic Oscillation method and give accurate results. The aerodynamic coefficients obtained from these methods are used for frequency domain flutter calculations involving a typical section blade structural model. An eigenvalue problem is solved for each interblade phase angle mode and the eigenvalues are used to determine aeroelastic stability. Flutter calculations are performed for two examples over a range of subsonic Mach numbers.

Bakhle, Milind A.↗
NASA NTRS1991

Experimental flutter boundaries with unsteady pressure distributions for the NACA 0012 Benchmark Model

The Structural Dynamics Div. at NASA-Langley has started a wind tunnel activity referred to as the Benchmark Models Program. The objective is to acquire test data that will be useful for developing and evaluating aeroelastic type Computational Fluid Dynamics codes currently in use or under development. The progress is described which was achieved in testing the first model in the Benchmark Models Program. Experimental flutter boundaries are presented for a rigid semispan model (NACA 0012 airfoil section) mounted on a flexible mount system. Also, steady and unsteady pressure measurements taken at the flutter condition are presented. The pressure data were acquired over the entire model chord located at the 60 pct. span station.

Rivera, Jose A., Jr.↗
NASA NTRS1991

User's guide to a system of finite-element supersonic panel flutter programs

The utilization and operation of a set of six computer programs for the prediction of panel flutter at supersonic speeds by finite element methods are described. The programs run individually to determine the flutter behavior of a flat panel where the finite elements which model the panel each have four degrees of freedom (DOF), a curved panel where the finite elements each have four DOF, and a curved panel where the finite elements each have six DOF. The panels are assumed to be of infinite aspect ratio and are subjected to either simply-supported or clamped boundary conditions. The aerodynamics used by these programs are based on piston theory. Application of the program is illustrated by sample cases where the number of beam finite elements equals four, the in-plane tension parameter is 0.0, the maximum camber to panel length ratio for a curved panel case is 0.05, and the Mach number is 2.0. This memorandum provides a user's guide for these programs, describes the parameters that are used, and contains sample output from each of the programs.

Woolley, Christine L.↗
NASA NTRS1991

Panel flutter in a low-density atmosphere

The problem of panel flutter is considered in the case of a free-molecule flow, the effect of the aerodynamic shear stress being incorporated into the structural model through distributed longitudinal and bending moment loads. This kind of analysis is relevant in the case of hypersonic flight vehicles, like the NASP, especially because in these conditions the shear stress can be expected to be considerably larger that the pressure at a given point. The aerodynamic loading is derived assuming a quasi-steady approximation. Two important parameters are given by alpha-m, the 'momentum accommodation coefficient', and Theta, the temperature ratio between the panel temperature and the temperature of the undisturbed flow. For high enough values of Theta the variation of the linear flutter parameter with alpha-m is close to linear. Comparison with continuum theory, given by linear piston theory, depends on the values of Theta and alpha-m considered. Finally, it is shown that buckling with respect to a uniform distributed longitudinal load is stabilizing.

Resende, Hugo B.↗
NASA NTRS1991

Cascade flutter analysis with transient response aerodynamics

Two methods for calculating linear frequency domain aerodynamic coefficients from a time-marching Full-Potential cascade solver are developed and verified. In the first method, the Influence Coefficient method, solutions to elemental problems are superposed to obtain the solutions for a cascade in which all blades are vibrating with a constant interblade phase angle. The elemental problem consists of a single blade in the cascade oscillating while the other blades remain stationary. In the second method, the Pulse Response method, the response to the transient motion of a blade is used to calculate influence coefficients. This is done by calculating the Fourier transforms of the blade motion and the response. Both methods are validated by comparison with the Harmonic Oscillation method and give accurate results. The aerodynamic coefficients obtained from these methods are used for frequency domain flutter calculations involving a typical section blade structural model. An eigenvalue problem is solved for each interblade phase angle mode and the eigenvalues are used to determine aeroelastic stability. Flutter calculations are performed for two examples over a range of subsonic Mach numbers using both flat plates and actual airfoils.

Bakhle, Milind A.↗
NASA NTRS1990

Design, implementation, simulation, and testing of digital flutter suppression systems for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind-tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the projet, and the development and successful use of a methodology for online controller performance evaluation.

Perry, Boyd, III↗
NASA NTRS1991

Experimental flutter boundaries with unsteady pressure distributions for the NACA 0012 Benchmark Model

The Structural Dynamics Division at NASA Langley Research Center has started a wind tunnel activity referred to as the Benchmark Models Program. The primary objective of the program is to acquire test data that will be useful for developing and evaluating aeroelastic type CFD codes currently in use of under development. This paper describes the progress achieved in testing the first model in the Benchmark Models Program. Experimental flutter boundaries are presented for a rigid semispan model (NACA 0012 airfoil section) mounted on a flexible mount system. Also, steady and unsteady pressure measurements taken at the flutter condition are presented. The pressure data were acquired over the entire model chord located at the 60 percent span station.

Rivera, Jose A.↗
NASA NTRS1991

A parametric sensitivity and optimization study for the active flexible wing wind-tunnel model flutter characteristics

In this paper an effort is made to improve the analytical open-loop flutter predictions for the Active Flexible Wing wind-tunnel model using a sensitivity based optimization approach. The sensitivity derivatives of the flutter frequency and dynamic pressure of the model with respect to the lag terms appearing in the Roger's unsteady aerodynamics approximations are evaluated both analytical and by finite differences. Then, the Levenberg-Marquardt method is used to find the optimum values for these lag-terms. The results obtained here agree much better with the experimental (wind tunnel) results than those found in the previous studies.

Rais-Rohani, Masoud↗
NASA NTRS1991

Nonlinear panel flutter in a rarefied atmosphere - Aerodynamic shear stress effects

The panel flutter phenomenon is studied assuming free-molecule flow. This kind of analysis is relevant in the case of hypersonic flight vehicles traveling at high altitudes, especially in the leeward portion of the vehicle. In these conditions the aerodynamic shear can be expected to be considerably larger than the pressure at a given point, so that the effects of such a loading are incorporated into the structural model. This is accomplished by introducing distributed longitudinal and bending moment loads. The former can lead to buckling of the panel, with the second mode in the case of a simply-supported panel playing a important role, and becoming the dominant mode in the solution. The presence of equivalent springs in the longitudinal direction at the panel's ends also becomes of relative importance, even for the evaluation of the linear flutter parameter. Finally, the behavior of the system is studied in the presence of applied compressive forces, that is, classical buckling.

Resende, Hugo B.↗
NASA NTRS1991

Controlling panel flutter using adaptive materials

The effectiveness of using adaptive materials to control panel flutter is examined. Adaptive materials are those whose strain or mechanical properties can be controlled by the application of an external stimulus. Two such material types are piezoelectric (ceramics or polymers) and shape memory alloys. These materials experience controllable strain when subjected to applied voltage and heat, respectively. The present study investigates the use of both material types to modify the flutter characteristics of a simply supported panel in supersonic flow. Piezoelectric materials respond quickly to applied voltages and can be used with feedback control for active vibration suppression. The adaptive process of the shape memory alloy used in this study (geometry and stiffness change) is a relatively low frequency phenomenon; therefore, it is considered for passive (on/off) control schemes only. Nondimensional parameters for these adaptive materials are used with linear panel models, yielding results which allow for a better understanding of their capabilities in controlling aeroelastic responses.

Scott, R. C.↗
NASA NTRS1991

Flutter control of incompressible flow turbomachine blade rows by splitter blades

Splitter blades as a passive flutter control technique is investigated by developing a mathematical model to predict the stability of an aerodynamically loaded splittered-rotor operating in an incompressible flow field. The splitter blades, positioned circumferentially in the flow passage between two principal blades, introduce aerodynamic and/or combined aerodynamic-structural detuning into the rotor. The two-dimensional oscillating cascade unsteady aerodynamics, including steady loading effects, are determined by developing a complete first-order unsteady aerodynamic analysis together with an unsteady aerodynamic influence coefficient technique. The torsion mode flutter of both uniformly spaced tuned rotors and detuned rotors are predicted by incorporating the unsteady aerodyamic influence coefficients into a single-degree-of-freedom aeroelastic model. This model is then utilized to demonstrate that incorporating splitters into unstable rotor configurations results in stable splittered-rotor configurations.

Chiang, Hsiao-Wei D.↗
NASA NTRS1991

Cascade flutter analysis with transient response aerodynamics

Two methods for calculating linear frequency domain aerodynamic coefficients from a time marching Full Potential cascade solver are developed and verified. In the first method, the Influence Coefficient, solutions to elemental problems are superposed to obtain the solutions for a cascade in which all blades are vibrating with a constant interblade phase angle. The elemental problem consists of a single blade in the cascade oscillating while the other blades remain stationary. In the second method, the Pulse Response, the response to the transient motion of a blade is used to calculate influence coefficients. This is done by calculating the Fourier Transforms of the blade motion and the response. Both methods are validated by comparison with the Harmonic Oscillation method and give accurate results. The aerodynamic coefficients obtained from these methods are used for frequency domain flutter calculations involving a typical section blade structural model. An eigenvalue problem is solved for each interblade phase angle mode and the eigenvalues are used to determine aeroelastic stability. Flutter calculations are performed for two examples over a range of subsonic Mach numbers.

Bakhle, M. A.↗