Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Ultrafast probing of the x-ray-induced lattice and electron dynamics in graphite at atomic-resolution

We used LCLS pulses to excite thin-film and bulk graphite with various different microstructures, and probed the ultrafast ion and electron dynamics through Bragg and x-ray Thomson scattering (XRTS). We pioneered XRTS at LCLS, making this technique viable for other users. We demonstrated for the first time that the LCLS can be used to characterize warm-dense-matter through Bragg and x-ray Thomson scattering. The warm-dense-matter conditions were created using the LCLS beam. Representative examples of the results are shown in the Figure above. In our experiment, we utilized simultaneously both Bragg and two Thomson spectrometers. The Bragg measurements as a function of x-ray fluence and pulse length allows us to characterize the onset of atomic motion at 2 keV with the highest resolution to date. The Bragg detector was positioned in back-reflection, providing us access to scattering data with large scattering vectors (nearly 4{pi}/{lambda}). We found a clear difference between the atomic dynamics for 70 and 300 fs pulses, and we are currently in the process of comparing these results to our models. The outcome of this comparison will have important consequences for ultrafast diffractive imaging, for which it is still not clear if atomic resolution can truly be achieved. The backward x-ray Thomson scattering data suggests that the average graphite temperature and ionization was 10 eV and 1.0, respectively, which agrees with our models. In the forward scattering data, we observed an inelastic feature in the Thomson spectrum that our models currently do not reproduce, so there is food for thought. We are in the process of writing these results up. Depending on if we can combine the Bragg and Thomson data or not, we plan to publish them in a single paper (e.g. Nature or Science) or as two separate papers (e.g. two Phys. Rev. Lett.). We will present the first analysis of the results at the APS Plasma Meeting in November 2010. We had a fantastic experience performing our experiment at the LCLS, and we are grateful to the beamline scientists and all the support personnel for enabling this experiment. A major hurdle was the very short transition time of two days, which despite all our preparations did not give us sufficient time to test the full system before the start of the beam time. We further were not able to make optimal use of the beam time since we had to exchange samples in the middle of the 36-hours shift. An additional 12-hours break could have avoided this. Finally, our experiment would have benefitted from the best possible focus, but 5 shifts do not allow performing the experiment while fine-tuning the focusing optics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Physicochemical investigations of carbon nanofiber supported Cu/ZrO{sub 2} catalyst

Zirconia-promoted copper/carbon nanofiber catalysts (Cu‐ZrO{sub 2}/CNF) were prepared by the sequential deposition precipitation method. The Herringbone type of carbon nanofiber GNF-100 (Graphite nanofiber) was used as a catalyst support. Carbon nanofiber was oxidized to (CNF-O) with 5% and 65 % concentration of nitric acid (HNO{sub 3}). The CNF activated with 5% HNO{sub 3} produced higher surface area which is 155 m{sup 2}/g. The catalyst was characterized by X-ray Diffraction (XRD), Fourier Transform Infra-Red (FTIR) and N{sub 2} adsorption-desorption. The results showed that increase of HNO{sub 3} concentration reduced the surface area and porosity of the catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of YBa{sub 2}Cu{sub 3}O{sub 7−δ} Superconductor/Graphene Oxide Composite

The aim of this research was to fabricate YBa{sub 2}Cu{sub 3}O{sub 7−δ} (YBCO) superconductor composite with graphene oxide nanosheets and to study the effect of the graphene oxide nanosheets on YBCO superconductor properties. For this purpose, the samples of pure superconductor and superconductor composite with 0.001, 0.01, and 0.1 wt.% graphene oxide were synthesized. First, graphite oxide was made by Hummer’s chemical method; after that, graphene oxide nanosheets were produced by bath-keeper ultrasonic. Then, different amounts of graphene oxide were added to the process of superconductor fabrication, which was made by solid-state reaction method. The samples were characterized and studied by Meissner effect test, XRD analysis, FESEM imaging, EDX measurement, and ac magnetic susceptibility. The critical current density (J{sub c}) of samples was measured by four probes method. The results showed that by increasing the weight ratio of graphene oxide, J{sub c} and T{sub c} decrease.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization of detonation soot produced during steady and overdriven conditions for three high explosive formulations

The detonation of high explosives (HE) produces a dense fluid of molecular gases and solid carbon. The solid detonation carbon contains various carbon allotropes such as detonation nanodiamonds, onion-like carbon, graphite and amorphous carbon, with the formation of the different forms dependent upon pressure, temperature and the environmental conditions of the detonation. We have collected solid carbon residues from controlled detonations of three HE formulations (Composition B-3, PBX 9501, and PBX 9502). Soot was collected from experiments designed to produce both steady and overdriven conditions, and from detonations in both an ambient (air) atmosphere and in an inert Ar atmosphere. Differences in solid carbon residues were quantified using X-ray photoelectron spectroscopy and carbon isotope measurements. Environmental conditions, HE formulation, and peak pressures influenced the amount of and isotopic composition of the carbon in the soot. Detonations in an Ar atmosphere produced greater amounts of carbon soot with lower δ 13 C values than those in ambient air. Therefore, solid carbon residues continued to evolve after detonation due to excess oxygen in the ambient air detonations. As well, higher peak pressures in overdriven conditions produced less carbon soot with, in general, higher δ 13 C values. Consequently, while overdriven conditions only produced peak pressures for a limited duration, it was enough to influence the composition of the solid carbon residues.

36 MATERIALS SCIENCE↗

Moiré nematic phase in twisted double bilayer graphene

Graphene moiré superlattices display electronic flat bands. At integer fillings of these flat bands, energy gaps due to strong electron-electron interactions are generally observed. However, the presence of other correlation-driven phases in twisted graphitic systems at non-integer fillings is unclear. Here, we report the existence of threefold rotational symmetry breaking in twisted double bilayer graphene. Using spectroscopic imaging over large and uniform areas to characterize the direction and degree of C 3 symmetry breaking, we find it to be prominent only at energies corresponding to the flat bands and nearly absent in the remote bands. We demonstrate that the magnitude of the rotational symmetry breaking does not depend on the degree of the heterostrain or the displacement field, being instead a manifestation of an interaction-driven electronic nematic phase. We show that the nematic phase is a primary order that arises from the normal metal state over a wide range of doping away from charge. Furthermore, our modelling suggests that the nematic instability is not associated with the local scale of the graphene lattice, but is an emergent phenomenon at the scale of the moiré lattice.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Single-particle chemical analysis reveals organic-rich detonation soot products

The detonation of high explosives produces a wide variety of particulate matter (PM) with distinct properties, not all of which are traditionally studied for chemical composition, formation processes, and forensic applications. We report particle-resolved measurements of Composition B detonation soot using soot particle aerosol mass spectrometry (SP-AMS), identifying carbonaceous species and metals not previously characterized on a single-particle basis. Results are combined with scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) to enhance source-dependent signatures. Black carbon, including graphitic carbon and detonation nanodiamonds, contributed 50.5-71.4% of PM 2.5 mass, while 22.5-43.4% was non-refractory organic carbon, a previously overlooked component that exhibited a complex and varying composition. Detonations were performed with and without PMMA confinement and under steady and overdriven conditions. Distinct particles enriched with polycyclic aromatic hydrocarbons (PAHs) were observed in experiments utilizing confinement, with quantities dependent on manufacturing method. SEM-EDS validated SP-AMS findings of metals internally mixed with carbonaceous species and extended the particle size range to 100 µm. This work makes detecting non-refractory organics using single-particle techniques more feasible for detonation forensics and understanding high-energy soot formation. While this analysis uses offline sample collection, SP-AMS could be deployed for in-situ measurements of detonation PM 2.5 transported in the atmosphere.

36 MATERIALS SCIENCE↗

p-Type BP nanosheet photocatalyst with AQE of 3.9% in the absence of a noble metal cocatalyst: investigation and elucidation of photophysical properties

While stability, significantly poor apparent quantum efficiency (AQE < 0.5%) and over dependence on noble metal cocatalysts is a long standing problem, here, we report, for the first time, microwave-exfoliated p-type few-layer black phosphorous (BP-nanosheets) as a stable photocatalyst for hydrogen production without any supporting noble metal co-catalyst. This few layer BP has shown a record high apparent quantum efficiency (AQE) of ~4% at 420 nm under visible light irradiation. This unprecedented AQE stems from a low level of material oxidation that impedes the degradation of BP under ambient conditions, strong absorption of photons at the surface, and a conduction band edge position that favorably facilitates the proton reduction reaction. These BP-nanosheets have also shown superior photocatalytic performance compared to the known cohort of metal-free photocatalysts such as graphitic carbon nitride, carbon dots, and red-P under identical experimental conditions. An understanding of the photo-physicochemical reasons that drive this chemistry is elucidated along with results obtained from physicochemical characterization and finite difference time domain simulations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of calcining temperature on photocatalysis of g-C{sub 3}N{sub 4}/TiO{sub 2} composites for hydrogen evolution from water

Highlights: • TiO{sub 2} promotes melon to form at 400 °C, whereas it forms at 500 °C for only melamine. • The highest photocatalytic activity was achieved when calcination was performed at 400 °C. • Coordinated N−Ti−N bonds were formed in MA/TiO{sub 2} (400) and disappeared at high temperature. • The surface area decreased and the pore size increased with increasing of temperature. • Only MA/TiO{sub 2} (400) has a narrower band gap than pure g-C{sub 3}N{sub 4}. - Abstract: A composite of graphitic carbon nitride and TiO{sub 2} (g-C{sub 3}N{sub 4}/TiO{sub 2}) with enhanced photocatalytic hydrogen evolution capacity was achieved by calcining melamine and TiO{sub 2} sol-gel precursor. Characterization results reveal that heating temperature had a great influence on the structure, surface area and properties of the composites. Compared with the polycondensation of pure melamine, the presence of TiO{sub 2} precursor can promote the formation of melon at a low temperature. The highest photocatalytic activity of g-C{sub 3}N{sub 4}/TiO{sub 2}(400) was achieved when the calcination was performed at 400 °C, exhibiting H{sub 2} production rate of 76.25 μmol/h under UV–vis light irradiation (λ > 320 nm) and 35.44 μmol/h under visible light irradiation (λ > 420 nm). The highest photocatalytic performance of g-C{sub 3}N{sub 4}/TiO{sub 2}(400) can be attributed to: (1) the strong UV–vis light absorption due to the narrow bandgap caused by synergic effect of TiO{sub 2} and g-C{sub 3}N{sub 4}, (2) high surface area and porosity, (3) the effective separation of photo-generated electron-holes owing to the favorable heterojunction between TiO{sub 2} and g-C{sub 3}N{sub 4}.

36 MATERIALS SCIENCE↗

C/CrC nanocomposite coating deposited by magnetron sputtering at high ion irradiation conditions

CrC with the fcc NaCl (B1) structure is a metastable phase that can be obtained under the non-equilibrium conditions of high ion irradiation. A nano-composite coating consisting of amorphous carbon embedded in a CrC matrix was prepared via the unbalanced magnetron sputtering of graphite and Cr metal targets in Ar gas with a high ionized flux (ion-to-neutral ratio Ji/Jn = 6). The nanoscale amorphous carbon clusters self-assembled into layers alternated by CrC, giving the composite a multilayer structure. The phase, microstructure, and composition of the coating were characterized using x-ray diffraction, transmission electron microscopy, and aberration corrected scanning transmission electron microscopy coupled with electron energy loss spectroscopy. The interpretation of the true coating structure, in particular the carbide type, is discussed.

36 MATERIALS SCIENCE↗

Electrochemical-driven green recovery of lithium, graphite and cathode from lithium-ion batteries using water

The expected exponential increase in consumption of lithium-ion batteries (LIBs) would pose a unique challenge to the availability of near-critical resources like lithium and graphite in the upcoming decade. In this work, we present a lithium recovery process that utilizes a degradation mechanism, i.e., lithium plating, as a tool to concentrate metallic lithium at the anode/separator interface for convenient extraction at room temperature – using only water. Electrochemical characterization of fast charged (1–6 C) LIBs yielded a maximum capacity fade of 50% over ten cycles. The lithium plating was confirmed via voltage plateau analysis, coulombic efficiency, and DC resistance measurements. A maximum lithium plating condition was observed to exist between 4C and 5C, thereby limiting the energy consumption in the extraction process. Post-mortem film thickness measurement showed an incrementing film deposition with a maximum of 35 µm thickness. SEM and XPS analysis confirmed increasing concentration of a dense dendritic metallic lithium deposition on the anode/separator interface with C-rate. A green recovery process was adopted to extract the concentrated metallic lithium using distilled water. The lithium from the plated film, solid/electrolyte interface (SEI), electrolyte, anode, and cathode, was extracted as salts. A 37% improvement in lithium recoverability was achieved with fast charging under ambient conditions. XPS analysis showed ~92% of lithium yield with no residual lithium in the graphite. In addition, the battery-grade graphite was recovered with 97% purity after heat treatment of the washed anode film, and concentrated transition metals oxides in the cathode to 93% purity for convenient extraction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-temperature low cycle fatigue behavior of a gray cast iron

The strain controlled low cycle fatigue properties of the studied gray cast iron for engine cylinder blocks were investigated. At the same total strain amplitude, the low cycle fatigue life of the studied material at 523 K was higher than that at 423 K. The fatigue behavior of the studied material was characterized as cyclic softening at any given total strain amplitude (0.12%–0.24%), which was attributed to fatigue crack initiation and propagation. Moreover, this material exhibited asymmetric hysteresis loops due to the presence of the graphite lamellas. Transmission electron microscopy analysis suggested that cyclic softening was also caused by the interactions of dislocations at 423 K, such as cell structure in ferrite, whereas cyclic softening was related to subgrain boundaries and dislocation climbing at 523 K. Micro-analysis of specimen fracture appearance was conducted in order to obtain the fracture characteristics and crack paths for different strain amplitudes. It showed that the higher the temperature, the rougher the crack face of the examined gray cast iron at the same total strain amplitude. Additionally, the microcracks were readily blunted during growth inside the pearlite matrix at 423 K, whereas the microcracks could easily pass through pearlite matrix along with deflection at 523 K. The results of fatigue experiments consistently showed that fatigue damage for the studied material at 423 K was lower than that at 523 K under any given total strain amplitude. - Highlights: • The low cycle fatigue behavior of the HT250 for engine cylinder blocks was investigated. • TEM investigations were conducted to explain the cyclic deformation response. • The low cycle fatigue cracks of HT250 GCI were studied by SEM. • The fatigue life of the examined material at 523 K is higher than that at 423 K.

36 MATERIALS SCIENCE↗

Superconducting magnesium diboride films for levitation of laser targets

Inertial confinement fusion targets would benefit from being levitated inside hohlraums to avoid capsule support-related implosion perturbations. Levitation inside a magnetic trap requires coating the capsule with a thin film that is superconducting at 20 K. Such non-epitaxial film growth on non-planar substrates is challenging. Here, we study Mg vapor annealing and solid-phase reactive inter-diffusion methods to form superconducting magnesium diboride (MgB 2 ) films on different planar and spherical carbon substrates, evaluating glassy carbon, polycrystalline diamond made by chemical vapor deposition, and carbon deposited by magnetron sputtering of graphite targets. Thin films of B and Mg are produced by magnetron sputtering onto stationary planar or rolling spherical substrates and annealed at either 600 or 850 °C in Mg vapor. The films are characterized by a combination of high-energy ion scattering, electron microscopy, and magnetometry. Results show that the critical superconducting temperature of resultant films depends on film microstructure and oxygen impurity content. The formation of MgB 2 films is also strongly substrate dependent, even in this case of non-epitaxial growth. Important factors to consider are oxygen outgassing of the substrate during thermal processing, substrate surface roughness, and the matching of thermal expansion coefficients of different layers in the multilayer structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nitrogen-doped mesoporous carbon for energy storage in vanadium redox flow batteries

We demonstrate an excellent performance of nitrogen-doped mesoporous carbon (N-MPC) for energy storage in vanadium redox flow batteries. Mesoporous carbon (MPC) is prepared using a soft-template method and doped with nitrogen by heat-treating MPC in NH{sub 3}. N-MPC is characterized with X-ray photoelectron spectroscopy and transmission electron microscopy. The redox reaction of [VO]{sup 2+}/[VO{sub 2}]{sup +} is characterized with cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalytic kinetics of the redox couple [VO]{sup 2+}/[VO{sub 2}]{sup +} is significantly enhanced on N-MPC electrode compared with MPC and graphite electrodes. The reversibility of the redox couple [VO]{sup 2+}/[VO{sub 2}]{sup +} is greatly improved on N-MPC (0.61 for N-MPC vs. 0.34 for graphite), which is expected to increase the energystorage efficiency of redoxflowbatteries. Nitrogen doping facilitates the electron transfer on electrode/electrolyte interface for both oxidation and reduction processes. N-MPC is a promising material for redoxflowbatteries. This also opens up new and wider applications of nitrogen-doped carbon.

25 ENERGY STORAGE↗

The many phases of CaC{sub 2}

Polymorphic CaC{sub 2} was prepared by reacting mixtures of CaH{sub 2} and graphite with molar ratios between 1:1.8 and 1:2.2 at temperatures between 700 and 1400 °C under dynamic vacuum. These conditions provided a well controlled, homogeneous, chemical environment and afforded products with high purity. The products, which were characterized by powder X-ray diffraction, solid state NMR and Raman spectroscopy, represented mixtures of the three known polymorphs, tetragonal CaC{sub 2}-I and monoclinic CaC{sub 2}-II and -III. Their proportion is dependent on the nominal C/CaH{sub 2} ratio of the reaction mixture and temperature. Reactions with excess carbon produced a mixture virtually free from CaC{sub 2}-I, whereas high temperatures (above 1100 °C) and C-deficiency favored the formation of CaC{sub 2}-I. From first principles calculations it is shown that CaC{sub 2}-I is dynamically unstable within the harmonic approximation. This indicates that existing CaC{sub 2}-I is structurally/dynamically disordered and may possibly even occur as slightly carbon-deficient phase CaC{sub 2-δ}. It is proposed that monoclinic II is the ground state of CaC{sub 2} and polymorph III is stable at temperatures above 200 °C. Tetragonal I represents a metastable, heterogeneous, phase of CaC{sub 2}. It is argued that a complete understanding of the occurrence of three room temperature modifications of CaC{sub 2} will require a detailed characterization of compositional and structural heterogeneities within the high temperature form CaC{sub 2}-IV, which is stable above 450 °C. The effect of high pressure on the stability of the monoclinic forms of CaC{sub 2} was studied in a diamond anvil cell using Raman spectroscopy. CaC{sub 2}-II and -III transform into tetragonal CaC{sub 2}-I at about 4 and 1GPa, respectively. - Graphical abstract: The famous tetragonal form of CaC{sub 2}, CaC{sub 2}-I, is dynamically unstable. Why does it exist? Display Omitted - Highlights: • Critical review of complex polymorphism of the commodity chemical CaC{sub 2}. • Tetragonal CaC{sub 2}-I is identified as dynamical instable and its existence attributed to disorder. • With pressure monoclinic CaC{sub 2}-II and –III transform into tetragonal CaC{sub 2}-I. • The high temperature form CaC{sub 2}-IV is assigned a key role for understanding the polymorphism of CaC{sub 2}.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Carbonaceous Material Properties and Their Interactions with Slag During Electric Arc Furnace Steelmaking

The state of the interface between slag and carbon determines the slag foaming behavior and thus the effectiveness of carbon in electric arc furnace (EAF) steelmaking. This paper explores the interaction between synthetic slag and carbonaceous materials derived from various sources, including bio-char produced by two different technologies, graphite, coke, and char from tire pyrolysis. Different interfacial phenomena were found between slag and the carbonaceous materials examined. The interactions between bio-char and slag are found to be poor in comparison with other carbonaceous materials. Carbonaceous materials were characterized in terms of their chemical composition and the results obtained suggested that interfacial phenomena were not dominated by ash in the carbonaceous material. The effects of carbon crystalline structure on interaction with slag were evaluated by Raman spectroscopy and X-ray diffraction. Surface properties of the samples were evaluated using scanning electron microscopy, and surface morphology was identified as the principal factor affecting the interaction of slag on carbonaceous particles. The smooth surface of bio-char results in reduced slag foaming. This finding forms the basis for future research on the production of bio-char to be used as a slag foaming agent in EAF steelmaking.

36 MATERIALS SCIENCE↗

Effect of Air Oxidation on Pore Structure Development and Mechanical Properties of Nuclear Graphite

This document reports on continuation of R&D activities at ORNL directed at investigating the effect of air oxidation of nuclear graphite on development and structure of porosity in the oxidized layer, and on the effect on mechanical properties of oxidized graphite. The material investigated was nuclear-grade graphite (purified PCEA graphite, from GrafTech International). Based on conclusions of previous work (ORNL/TM-2009/192), the method of analysis of the porosity in the oxidized layer based on optical microscopy coupled with automated image analysis was further improved and standardized. In addition, characterization of oxidized specimens by optical microscopy was complemented with measurements of mechanical properties (compressive strength) on a statistically significant number of specimens. A series of cylindrical shape specimens were machined and oxidized in air at two temperatures (600 and 700 o C) and at three levels of burn-off at each temperature (5-6 %; 10-12 % and 15-17%). The procedure used for specimen preparation and oxidation, and the oxidation equipment, were those recommended in ASTM D-7542-09. However, in order to comply with the aspect ratio requirements for specimens employed in compressive strength measurements (ASTM C-695-91) all specimens were machined with a length to diameter ratio of 2 (i.e. 25.4 mm height vs. 12.7 mm diameter) instead of 25.4 mm length and 25.4 mm diameter recommended by ASTM D-7542-09. After oxidation, mechanical properties (compressive strength) were measured on at least three samples obtained at equal oxidation conditions, while another specimen from the same lot was sectioned, mounted in resin and surface polished for optical microscopy analysis. In the latter procedure, mosaic pictures were collected of a rectangular stripe across the diameter of each specimen. These images were analyzed in order to derive the penetration depth and the pore structure in the oxidized layer as a function of oxidation temperature and weight loss level. Automated image analysis was performed using the commercial software Image Pro Plus. The results led to the conclusion that the depth of the oxidation layer is more dependent on the oxidation temperature than on the level of weight-loss. The penetration depth of the oxidized layer is about 6 mm at 600 o C and about 1.5 mm at 700 o C. Consequently, the 12.5 mm diameter specimens oxidized at 600 o C were completely penetrated by oxidation, while those oxidized at 700 o C had the oxidation layer restricted in a narrower band near the exposed surface. This difference was reflected by mechanical properties. A closer analysis of high magnification images in the oxidized layer revealed that oxidation attacks preferentially the binder phase in graphite, where development of fine new pores was observed. The density of new pores was higher near large pores pre-existing in graphite structure. Acute oxidation at low temperatures (e.g. 600 o C) causes more damage on mechanical strength than high temperature oxidation (700 o C). Although the latter is much faster, the oxidized layer is limited to a narrow zone next to the external surface, so that the core is not visibly affected. In contrast, oxidation at lower temperature, although slower, is more damaging because it penetrates deeply beyond the exposed surface.

36 MATERIALS SCIENCE↗

Mesoporous Textured Fe-N-C Electrocatalysts as Highly Efficient Cathodes for Proton Exchange Membrane Fuel Cells

A new platinum group metal (PGM)-free proton exchange membrane fuel cell (PEMFC) cathode catalyst materials, synthesized using the VariPore™ method by Pajarito Powder, LLC, are characterized for their structure and activity. The physico-chemical analysis of the iron-nitrogen-carbon (Fe-N-C) electrocatalysts show mesoporous carbon material effectively doped with iron and nitrogen. The materials have an average pore size of 7-8 nm and high specific surface area. The Fe-N-C catalysts exhibit good oxygen reduction reaction (ORR) activity in 0.5 M H2SO4 electrolyte with high half-wave potential and sustainable electrochemical stability over 10,000 repeated potential cycles with insignificant losses in their activities. As cathode catalysts in a PEMFC, the Fe-N-C materials deliver remarkably good fuel cell performance at low overpotential approaching that of the commercial Pt catalyst. The high ORR electrocatalytic activity of these Fe-N-C catalysts is credited to the synergy between nitrogen-moieties, specifically pyrrolic-N, pyridinic-N, and graphitic-N, and iron in addition to the high mesoporosity that facilitate an effective reaction path in boosting the electrocatalytic activity and stability.

DIRECT ENERGY CONVERSION↗