Results for “Hover Performance” — Page 30

NASA NTRS1979

A piloted simulator investigation of helicopter precision decelerating approaches to hover to determine single-pilot IFR /SPIFR/ requirements

The results of single-pilot instrument flight rules (SPIFR) experiments conducted on the NASA-Ames V/STOLAND simulator are presented. Several factors having a significant impact on requirements for helicopter SPIFR decelerating, steep approaches to landing are considered: (1) approach weather conditions, (2) flight path geometry, (3) deceleration guidance law, (4) level of stability and command augmentation, (5) cockpit display sophistication, (6) accuracy of navigation aids, and (7) helipad lighting and visual aids. Particular emphasis is placed on the relative effects of deceleration profile, control augmentation, and flight director parameters on pilot performance, workload, and opinion rating. Problems associated with the development of a pilot acceptance analytical methodology are outlined.

Phatak, A. V.↗

NASA NTRS2016

Second-Generation Large Civil Tiltrotor 7- by 10-Foot Wind Tunnel Test Data Report

An approximately 6-percent scale model of the NASA Second-Generation Large Civil Tiltrotor (LCTR2) Aircraft was tested in the U.S. Army 7- by 10-Foot Wind Tunnel at NASA Ames Research Center January 4 to April 19, 2012, and September 18 to November 1, 2013. The full model was tested, along with modified versions in order to determine the effects of the wing tip extensions and nacelles; the wing was also tested separately in the various configurations. In both cases, the wing and nacelles used were adopted from the U.S. Army High Efficiency Tilt Rotor (HETR) aircraft, in order to limit the cost of the experiment. The full airframe was tested in high-speed cruise and low-speed hover flight conditions, while the wing was tested only in cruise conditions, with Reynolds numbers ranging from 0 to 1.4 million. In all cases, the external scale system of the wind tunnel was used to collect data. Both models were mounted to the scale using two support struts attached underneath the wing; the full airframe model also used a third strut attached at the tail. The collected data provides insight into the performance of the preliminary design of the LCTR2 and will be used for computational fluid dynamics (CFD) validation and the development of flight dynamics simulation models.

Theodore, Colin R.↗

NASA NTRS2024

Fundamental Proprotor Design Considerations

The purpose of this technical memorandum is to document some of the fundamental considerations in the aerodynamic design of a proprotor blade, which include distributions of twist, chord, and thickness. A proprotor is expected to operate efficiently in different speed regimes, such as hover and forward flight, which presents challenges that are unique from designing either rotors or propellers. Operating in hover and at high advance ratios in cruise present conflicting design requirements on the blade's geometry that must be reconciled with the vehicle's mission. Though a proprotor must also fly in edgewise and other non-axial flight phases, these portions of the mission do not typically drive the proprotor's aerodynamic design. This memorandum describes an approach to integrate a blade's twist and chord distributions to provide an aerodynamic performance estimate that could be coupled with other design considerations, such as acoustics or structures. The intended audience for this memorandum is engineers beginning to work in this discipline who are looking for a primer on the behavior of proprotor performance and design considerations. The memorandum is not intended as a step-by-step guide to designing proprotors, nor does it provide insight into more advanced proprotor design/analysis tools.

Rotor Aerodynamics↗

NASA NTRS2020

Mars Science Helicopter Conceptual Design

Robotic planetary aerial vehicles increase the range of terrain that can be examined, compared to traditional landers and rovers, and have more near-surface capability than orbiters. Aerial mobility is a promising possibility for planetary exploration as it reduces the challenges that difficult obstacles pose to ground vehicles. The first use of a rotorcraft for a planetary mission will be in 2021, when the Mars Helicopter technology demonstrator will be deployed from the Mars 2020 rover. The Jet Propulsion Laboratory and NASA Ames Research Center are exploring possibilities for a Mars Science Helicopter, a second-generation Mars rotorcraft with the capability of conducting science investigations independently of a lander or rover (although this type of vehicle could also be used assist rovers or landers in future missions). This report describes the conceptual design of Mars Science Helicopters. The design process began with coaxial-helicopter and hexacopter configurations, with a payload in the range of two to three kg and an overall vehicle mass of approximately twenty kg. Initial estimates of weight and performance were based on the capabilities of the Mars Helicopter. Rotorcraft designs for Mars are constrained by the dimensions of the aeroshell and lander for the trip to the planet, requiring attention to the aircraft packaging in order to maximize the rotor dimensions and hence overall performance potential. Aerodynamic performance optimization was conducted, particularly through airfoils designed specifically for the low Reynolds number and high Mach number inherent to operation on Mars. Rotor structural designs were developed that met blade frequency and weight targets, subject to material stress limits. The final designs show a substantial capability for science operations on Mars: a 31 kg hexacopter that fits within a 2.5 m diameter aeroshell could carry a 5 kg payload for 10 min of hover time or over a range of 5 km.

Wayne Johnson↗

NASA NTRS1982

Helistat simulation studies

An analysis of the flight dynamics and piloted control characteristics of the Helistat, a quadrotor heavy-lift airship, was completed using the HYBRDS airship simulation facility. The analysis covered the full operating flight envelope, including likely ranges of altitude, airspeed, sideslip, and loading variations. Particular areas of study were performance, trim, power requirements, linearized dynamics, handling qualities, and mooring operations. The key assumptions were: a rigid vehicle, no control system dynamics, fixed rotor and propeller RPM, and no ballonet dynamics. The nominal cruise speed for the H34 engines operating at 1275 HP was found to be 40-50 kts, depending on the loading condition. The maximum payload capability was calculated as 45,000 lbs for sea level-based operations. The crosswind capability in hover is 5-10 kts depending on the loading conditions, but this requires excessive roll angle due to the roll-to-translate control gearing. Sideslip angles of 110-135 degrees (wind from aft quarters) are critical for directional trim and stability, and should be avoided.

Tischler, M. B.↗

NASA NTRS1990

Analysis of internal flow in a ventral nozzle for STOVL aircraft

Short takeoff and vertical landing (STOVL) aircraft are planned for possible future development. For these aircraft, the same propulsion system will provide power for lift, hover, and horizontal flight. To accomplish this, many designs include a ventral nozzle to provide part of the vertical thrust required. Understanding and predicting the internal aerodynamic flow caused by a single exhaust duct opening are highly desirable in assessing this concept. A numerical simulation of a ventral nozzle is presented and the results are compared with experimental data. Comparisons include visualizations of the flow along the ventral duct walls and in the tailpipe plane of symmetry. Performance calculations are also compared with measured values.

Smith, C. Frederic↗

NASA NTRS1990

Analysis of internal flow in a ventral nozzle for STOVL aircraft

Short takeoff and vertical landing (STOVL) aircraft are planned for possible future development. For these aircraft, the same propulsion system will provide power for lift, hover, and horizontal flight. To accomplish this, many designs include a ventral nozzle to provide part of the vertical thrust required. Understanding and predicting the internal aerodynamic flow caused by a single exhaust duct opening are highly desirable in assessing this concept. A numerical simulation of a ventral nozzle is presented and the results are compared with experimental data. Comparisons include visualizations of the flow along the ventral duct walls and in the tailpipe plane of symmetry. Performance calculations are also compared with measured values.

Smith, C. Frederic↗

NASA NTRS1985

Visual and motion cueing in helicopter simulation

Early experience in fixed-cockpit simulators, with limited field of view, demonstrated the basic difficulties of simulating helicopter flight at the level of subjective fidelity required for confident evaluation of vehicle characteristics. More recent programs, utilizing large-amplitude cockpit motion and a multiwindow visual-simulation system have received a much higher degree of pilot acceptance. However, none of these simulations has presented critical visual-flight tasks that have been accepted by the pilots as the full equivalent of flight. In this paper, the visual cues presented in the simulator are compared with those of flight in an attempt to identify deficiencies that contribute significantly to these assessments. For the low-amplitude maneuvering tasks normally associated with the hover mode, the unique motion capabilities of the Vertical Motion Simulator (VMS) at Ames Research Center permit nearly a full representation of vehicle motion. Especially appreciated in these tasks are the vertical-acceleration responses to collective control. For larger-amplitude maneuvering, motion fidelity must suffer diminution through direct attenuation through high-pass filtering washout of the computer cockpit accelerations or both. Experiments were conducted in an attempt to determine the effects of these distortions on pilot performance of height-control tasks.

Bray, R. S.↗

NASA NTRS1986

Visual and motion cueing in helicopter simulation

The visual cues presented in the simulator are compared with those of flight in an attempt to identify deficiencies. For the low-amplitude maneuvering tasks normally associated with the hover mode, the unique motion capabilities of the Vertical Motion Simulator (VMS) at Ames Research Center permit nearly a full representation of vehicle motion. Especially appreciated in these tasks are the vertical-acceleration responses to collective control. For larger-amplitude maneuvering, motion fidelity must suffer diminution through direct attenuation through high-pass filtering washout of the computer cockpit accelerations or both. Experiments were conducted in an attempt to determine the effects of these distortions on pilot performance of height-control tasks.

Bray, Richard S.↗

NASA NTRS2002

Computational Analysis of a Prototype Martian Rotorcraft Experiment

This paper presents Reynolds-averaged Navier-Stokes calculations for a prototype Martian rotorcraft. The computations are intended for comparison with an ongoing Mars rotor hover test at NASA Ames Research Center. These computational simulations present a new and challenging problem, since rotors that operate on Mars will experience a unique low Reynolds number and high Mach number environment. Computed results for the 3-D rotor differ substantially from 2-D sectional computations in that the 3-D results exhibit a stall delay phenomenon caused by rotational forces along the blade span. Computational results have yet to be compared to experimental data, but computed performance predictions match the experimental design goals fairly well. In addition, the computed results provide a high level of detail in the rotor wake and blade surface aerodynamics. These details provide an important supplement to the expected experimental performance data.

Corfeld, Kelly J.↗

NASA NTRS2001

Computational Analysis of a Prototype Martian Rotorcraft Experiment

This paper presents Reynolds-averaged Navier-Stokes calculations for a prototype Martian rotorcraft. The computations are intended for comparison with an ongoing Mars rotor hover test at NASA Ames Research Center. These computational simulations present a new and challenging problem, since rotors that operate on Mars will experience a unique low Reynolds number and high Mach number environment. Computed results for the 3-D rotor differ substantially from 2-D sectional computations in that the 3-D results exhibit a stall delay phenomenon caused by rotational forces along the blade span. Computational results have yet to be compared to experimental data, but computed performance predictions match the experimental design goals fairly well. In addition, the computed results provide a high level of detail in the rotor wake and blade surface aerodynamics. These details provide an important supplement to the expected experimental performance data.

Corfeld, Kelly J.↗

NASA NTRS1987

Analysis of a fixed-pitch X-wing rotor employing lower surface blowing

Lower surface blowing (LSB) is investigated as an alternative to the variable blade pitch requirement for the X-wing Circulation Control (CC) rotor concept. Addition trailing edge blowing slots on the lower surfaces of CC airfoils provide a bidirectional lift capability that effectively doubles the control range. The operational requirements of this rotor system are detailed and compared to the projected performance attributes of LSB airfoils. Analysis shows that, aerodynamically, LSB supplies a fixed pitch rotor system with the equivalent lift efficiency and rotor control of present CC rotor designs that employ variable blade pitch. Aerodynamic demands of bidirectional lift production are predicted to be within the capabilities of current CC airfoil design methodology. Emphasis in this analysis is given to the high speed rotary wing flight regime unique to stoppable rotor aircraft. The impact of a fixed pitch restriction in hover and low speed flight is briefly discussed.

Schwartz, Alan W.↗

NASA NTRS2000

Fluid Mechanics, Drag Reduction and Advanced Configuration Aeronautics

This paper discusses Advanced Aircraft configurational approaches across the speed range, which are either enabled, or greatly enhanced, by clever Flow Control. Configurations considered include Channel Wings with circulation control for VTOL (but non-hovering) operation with high cruise speed, strut-braced CTOL transports with wingtip engines and extensive ('natural') laminar flow control, a midwing double fuselage CTOL approach utilizing several synergistic methods for drag-due-to-lift reduction, a supersonic strut-braced configuration with order of twice the L/D of current approaches and a very advanced, highly engine flow-path-integrated hypersonic cruise machine. This paper indicates both the promise of synergistic flow control approaches as enablers for 'Revolutions' in aircraft performance and fluid mechanic 'areas of ignorance' which impede their realization and provide 'target-rich' opportunities for Fluids Research.

Bushnell, Dennis M.↗

NASA NTRS1978

Simulator evaluation of three situation and guidance displays for V/STOL aircraft zero-zero landing approaches

A simulator study was undertaken to compare and evaluate the design features of the electronic displays for possible use in V/STOL aircraft: a combined transition display (Display A), a perspective display (Display B), and a hover display (Display C). Display B presents height information via integrated elements; Displays A and C present information similarly except that Display C presents vertical and lateral guidance via conventional cross pointers. High pilot work load was attained by evaluating the displays only as situational guidance displays in a simulated vehicle without stability augmentation. Glide slopes of 6 and 15 deg were used, and steady-state and no-wind conditions were randomly presented. Six pilots participated, and fifty-five objective performance measures were taken along with pilot opinions

Murphy, M. R.↗

NASA NTRS1986

Effects of simulator variations on the fidelity of a UH-60 Black Hawk simulation

The validity of the vertical motion simulator used to simulate the UH-60A Black Hawk helicopter is evaluated. Aircraft simulation of bob-up, hover turn, and dash/quick stop manuevers are compared to actual flight data. The effects of variations in the simulator's visual and motion characteristics on the simulation data are investigated. Data obtained with the nonintrusive parameter identification procedure and optimal control measures are applied to the helicopter math model used for real-time aircraft simulation. Analysis of the model reveals that the simulated aircraft is underdamped, and the changes in the visual reference have the greatest effect on the ability of the pilot to perform the maneuvers.

Cleveland, W. B.↗

NASA NTRS2016

Measurement and Modelling of Multicopter UAS Rotor Blades in Hover

Multicopters are becoming one of the more common and popular type of unmanned aircraft systems (UAS) which have both civilian and military applications. One example being the concept of drone deliveries proposed by the distribution company Amazon [1]. The electrical propulsion is considered to have both faster and easier deliveries and also environmental benefits compared to other vehicles that still use fossil fuel. Other examples include surveillance and just simple entertainment. The reason behind their success is often said to be due to their small size, relatively low cost, simple structure and finally simple usage. With an increase in the UAS market comes challenges in terms of security, as both people and other aircrafts could be harmed if not used correctly. Therefore further studies and regulations are needed to ensure that future use of drones, especially in the civilian and public sectors, are safe and efficient. Thorough research has been done on full scale, man or cargo transporting, helicopters so that most parts of flight and performance are fairly well understood. Yet not much of it have been verified for small multicopters. Until today many studies and research projects have been done on the control systems, navigation and aerodynamics of multicopters. Many of the methods used today for building multicopters involve a process of trial an error of what will work well together, and once that is accomplished some structural analysis of the multicopter bodies might be done to verify that the product will be strong enough and have a decent aerodynamic performance. However, not much has been done on the research of the rotor blades, especially in terms of structural stress analyses and ways to ensure that the commonly used parts are indeed safe and follow safety measures. Some producers claim that their propellers indeed have been tested, but again that usually tends towards simple fluid dynamic analyses and even simpler stress analyses. There is no real deflection measurement of said blades and all theory is today based on the theory developed for full scale helicopters. This report thus intends to highlight the problems that come with blade deflection theory and measurements for multicopters. This thesis starts with the introduction and problem formulation where the grounds for what the report contains are laid out. Then a literature review of the research within the area follows where previous and current research and methods are presented. In the background information and theory relevant to the area are presented. After that the methods and set up of the different experimental and computer simulation approaches are depicted. In the results section the obtained results are presented and compared. Lastly there is a discussion where the results and methods are evaluated and analyzed, followed by the most important conclusions.

Multicopter UAS Rotor Blades↗

NASA NTRSDate not supplied

An Overview of the Proprotor Performance Test in the 14- by 22-Foot Subsonic Tunnel

This work experimentally investigates the aerodynamic behavior of proprotors across a wide range of angles of attack. These flight conditions are intended to be representative of Urban Air Mobility (UAM) vehicle platforms that utilize articulating propulsors to transition from a vertical takeoff and landing (VTOL) phase typical of a conventional rotorcraft, to an axial mode of forward flight typical of a fixed-wing aircraft. These data are used to identify the potential limits of lower fidelity aerodynamic modeling tools, as well as to inform future acoustic phases of testing. Tests were conducted on two proprotor designs in the NASA Langley 14- by 22-Foot Subsonic Tunnel using an articulating propeller test stand. Hover results identified unique flow physics on one of the proprotors, including severe outboard flow separation and perpendicular blade vortex interactions on the outboard portions of the blades. Transition and forward flight conditions yielded very informative trends in terms of both on- and off-axis forces and moments against which low-fidelity prediction models were compared.

Nikolas Zawodny↗

NASA NTRSDate not supplied

An Overview of the Proprotor Performance Test in the 14- by 22-Foot Subsonic Tunnel

This work experimentally investigates the aerodynamic behavior of proprotors across a wide range of angles of attack. These flight conditions are intended to be representative of Urban Air Mobility (UAM) vehicle platforms that utilize articulating propulsors to transition from a vertical takeoff and landing (VTOL) phase typical of a conventional rotorcraft, to an axial mode of forward flight typical of a fixed-wing aircraft. These data are used to identify the potential limits of lower fidelity aerodynamic modeling tools, as well as to inform future acoustic phases of testing. Tests were conducted on two proprotor designs in the NASA Langley 14- by 22-Foot Subsonic Tunnel using an articulating propeller test stand. Hover results identified unique flow physics on one of the proprotors, including severe outboard flow separation and perpendicular blade vortex interactions on the outboard portions of the blades. Transition and forward flight conditions yielded very informative trends in terms of both on- and off-axis forces and moments against which low-fidelity prediction models were compared.

aerodynamics↗