SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Research into the nondestructive evaluation of advanced reinforced composite laminates is summarized. The applicability of the Framers-Kronig equations to the nondestructive evaluation of composite materials is described.
The extension of linear elastic fracture mechanics (LEFM) from metallic alloys to advanced fiber composite laminates is considered. LEFM is shown to be valid for both isotropic and anisotropic homogeneous continua; the applicability of LEFM to advanced fiber composites is thus dependent on the validity of a homogeneous model of such materials. An experimental program to determine the validity of such a model for graphite/epoxy laminates is reviewed. Such laminates are found to have an apparent fracture toughness, from which it is inferred that a homogeneous material model is valid for the particular specimen geometry and composite laminates considered. Strain energy release rates are calculated from the experimentally determined fracture toughness of the various laminates. These strain energy release rates are found to lie in one of two groups, depending upon whether crack extension required fiber failure or matrix failure. The latter case is further investigated. It is concluded that matrix failure is governed by the tensile stress normal to the crack path.
A model for the prediction of loading sequence effects on the statistical distribution of fatigue life and residual strength in composite materials is generalized and applied to (0/90/45/-45)s graphite/epoxy laminates. Load sequence effects are found to be caused by both the difference in residual strength when failure occurs (boundary effect) and the effect of previously applied loads (memory effect). The model allows the isolation of these two effects, and the estimation of memory effect magnitudes under dual fatigue loading levels. It is shown that the material memory effect is insignificant, and that correlations between predictions of the number of early failures agree with the verification tests, as do predictions of fatigue life and residual strength degradation under dual stress levels.
In this study, the fatigue crack growth behavior of fiber bridging matrix cracks in cross-ply SCS-6/Ti-15-3 and SCS-6/Timetal-21S laminates containing center holes was investigated. Experimental observations revealed that matrix cracking was far more extensive and wide spread in the SCS-6/Ti-15-3 laminates compared to that in the SCS-6/Timetal-21S laminates. In addition, the fatigue life of the SCS-6/Ti-15-3 laminates was significantly longer than that of the SCS-6/Timetal-21S laminates. The matrix cracking observed in both material systems was analyzed using a fiber bridging (FB) model which was formulated using the boundary correction factors and weight functions for center hole specimen configurations. A frictional shear stress is assumed in the FB model and was used as a curve fitting parameter to model matrix crack growth data. The higher frictional shear stresses calculated in the SCS-6/Timetal-21S laminates resulted in lower stress intensity factors in the matrix and higher axial stresses in the fibers compared to those in the SCS-6/Ti-15-3 laminates at the same applied stress levels.
A computational procedure is presented for evaluating the analytic sensitivity derivatives of the tire response with respect to material and geometrical properties of the tire. The tire is modeled by using a two-dimensional laminated anisotropic shell theory with the effects of variation in material and geometric parameters included. The computational procedure is applied to the case of the Space Shuttle orbiter nose-gear tire subjected to uniform inflation pressure. Numerical results are presented which show the sensitivity of the different tire response quantities to variations in the material characteristics of both the cord and rubber.
A computational procedure is presented for evaluating the analytic sensitivity derivatives of the tire response with respect to material and geometric parameters of the tire. The tire is modeled by using a two-dimensional laminated anisotropic shell theory with the effects of variation in material and geometric parameters included. The computational procedure is applied to the case of uniform inflation pressure on the Space Shuttle nose-gear tire when subjected to uniform inflation pressure. Numerical results are presented showing the sensitivity of the different response quantities to variations in the material characteristics of both the cord and the rubber.
This volume discusses a vaety of applications of both low- and high-cost composite materials in a number of selected engineering fields. The text stresses the use of fiber-reinforced composites, along with interesting material systems used in the electrical and nuclear industries. As to technology transfer, a similarity is noted between many of the reasons responsible for the utilization of composites and those problems requiring urgent solution, such as mechanized fabrication processes and design for production. Features topics include road transportation, rail transportation, civil aircraft, space vehicles, builing industry, chemical plants, and appliances and equipment. The laminate orientation code devised by Air Force materials laboratory is included. Individual items are announced in this issue.
The application of advanced composite materials in aerospace, ground transportation, and sporting industries are discussed. Failure theories for the design and mechanical behavior of composite materials are emphasized. Methods for detecting specific types of flaws are outlined. The effect of detected flaws on mechanical properties such as stiffness, strength, fatigue lifetime, or residual strength is described.
PSANAL computes composite-laminate elastic and thermal properties and allowable load levels for any combination of applied membrane and bending loads occurring at a point. Basic linear orthotropic stress/ strain relationships and standard composite-laminate theory formulas are utilized.
The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.
The impact damage response of two thermoplastic material systems were compared over a range of impact energies. Eight-inch-square impact specimens with a 24-ply quasi-isotropic layup were manufactured from TC1225 LMPAEK T700G from Toray Industries and APC AS4D/PEKK-FC from Solvay. The effect of the degree of crystallinity (DOC) on the damage response was also investigated using a third set of specimens from the Toray material manufactured with reduced crystallinity. Using a combination of data obtained from X-ray computed tomography (CT) scans and ultrasonic testing (UT), detailed damage maps were created for every interface and ply for selected specimens. Using these damage maps, the delamination size, shape, and area were evaluated at each interface. The presence of fractured fibers was also identified on each ply. The LMPAEK material was found to have fewer and smaller delaminations than the PEKK specimens for impacts at the same energy. However, the LMPAEK specimens contained a larger number of fiber breaks. A similar trend was observed when comparing the baseline LMPAEK specimens with the low-crystallinity LMPAEK specimens. The low-crystallinity specimens had very little delamination but had a large number of plies with fiber breaks. In addition, the LMPAEK specimens often contained lines of fiber fractures in near-surface plies emanating from the contact region that were not present in the PEKK specimens.
The fracture behavior of hybrid (buffer strip) laminated composites is predicted by a novel method in terms of material properties, geometry, and internal damage. Attention is given to the cases of broken fibers in a unidirectional half-plane, adjoined half-planes having different fiber and matrix properties, and the solution of two half-planes bounding a third, distinct region of finite width. The analysis is based on a materials modeling approach using the classical shear-lag assumption to represent the stress transfer between fibers. Explicit fiber and matrix properties of the three regions are retained, and changes in the laminate behavior as a function of the material properties, buffer strip width and initial crack length are discussed.
A study of interaction between wing bending and twist by graphite/epoxy anisotropic laminates used in aircraft wing skins is presented. The laminates were used as covers for subscale box beams supported as a cantilever and tested in tip shear and tip torque, measuring beam response with a reflected light technique. The results indicated that the in-plane stiffness properties of anisotropic laminates can be predicted if the layer properties of the composite materials are known; thus, the coupled bending/twist response of wing type structures made from these laminates can be determined provided the limits of the laminate linear behavior are not significantly exceeded.
The impact sensitivity of aramide fiber-reinforced aluminum laminates (ARALL) was investigated by testing two types of ARALL (7075 aluminum prestrained and 2024 aluminum not prestrained), via static indentation, and the results were compared to those of sheet aluminum alloys 7075-T6 and 2024-T3 and to a state of the art composite AS6/5245. It was found that the impact resistance of the two ARALL samples was inferior to that of monolithic sheet aluminum samples, although the ARALL material made with 2024-T3 aluminum was superior to that made with 7075-T6 aluminum. The impact damage resistance of ARALL materials was at least equal to that of AS6/5245, and the AS6/5245 had higher residual tension-tension fatigue strength after impact than the ARALL samples. It was also found that the prestraining of the ARALL reduced the fatigue growth of impact damage.
Probabilistic predictions based on the Integrated Probabilistic Assessment of Composite Structures (IPACS) code are presented for the material and structural response of unnotched and notched, 1M6/3501-6 Gr/Ep laminates. Comparisons of predicted and measured modulus and strength distributions are given for unnotched unidirectional, cross-ply, and quasi-isotropic laminates. The predicted modulus distributions were found to correlate well with the test results for all three unnotched laminates. Correlations of strength distributions for the unnotched laminates are judged good for the unidirectional laminate and fair for the cross-ply laminate, whereas the strength correlation for the quasi-isotropic laminate is deficient because IPACS did not yet have a progressive failure capability. The paper also presents probabilistic and structural reliability analysis predictions for the strain concentration factor (SCF) for an open-hole, quasi-isotropic laminate subjected to longitudinal tension. A special procedure was developed to adapt IPACS for the structural reliability analysis. The reliability results show the importance of identifying the most significant random variables upon which the SCF depends, and of having accurate scatter values for these variables.
The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F)has been demonstrated using a block copolymer, BlCo(13), PPQ derivative. Initially, thirteen polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), and tensile strength and modulus at ambient temperature. A block copolymer (Bl Co 13) derived from one mole p-bis (phenylglyoxalyl) benzene, one fourth mole 3,3'-diaminobenzidine and three-fourths mole 3,3', 4,4'-tetraminobenzophenone was selected for extensive study. Tensile, flexural, and interlaminar shear values were obtained after aging and testing postcured BlCo(13) laminates at 316 C (600 F). The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.
The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F) has been demonstrated using a block copolymer, BICo(1:3), PPQ derivative. Initially, 13 polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), tensile strength, and modulus of ambient temperature. The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.
Anisotropic plate theory is used to calculate the anisotropic stress concentration factors for a composite plate (AS/3501-5 graphite/epoxy composite, single ply or laminated) containing a circular hole. This composite material is used on the highly maneuverable aircraft technology (HiMAT) vehicle. It is found that the anisotropic stress concentration factor could be greater or less than 3 (the stress concentration factor for isotropic materials), and that the locations of the maximum tangential stress points could shift with the change of fiber orientation with respect to the loading axis. The effect of hole size on the stress concentration factor is examined using the Point Stress Criterion and the Averaged Stress Criterion. The predicted stress concentration factors based on the two theories compared fairly well with the measured values for the hole size 0.3175 cm (1/8 in). It is also found that through the lamination process, the stress concentration factor could be reduced drastically, indicating an improvement in structural performance.