Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIGNITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Bulk Production of Any Ratio 12 C: 13 C Turbostratic Flash Graphene and Its Unusual Spectroscopic Characteristics

As graphene enjoys worldwide research and deployment, the biological impact, geologic degradation, environmental retention, and even some physical phenomena remain less well studied. Bulk production of 13 C-graphene yields a powerful route to study all of these questions. Gram scale synthesis of high quality and high purity turbostratic flash graphene with varying amounts of 13 C-enrichment, from 5% to 99% is reported here. Here, the material is characterized by solid state nuclear magnetic resonance spectroscopy, Raman spectroscopy, infrared (IR) spectroscopy, X-ray photoelectron spectroscopy and inductively coupled plasma mass spectrometry. Notably, an unusual enhancement in the Raman spectroscopic D’ peak is observed, resulting from the modification in vibrational frequency through isotopic enrichment favoring intravalley phonon scattering modes. While the IR absorbance spectrum of graphene is for the most part silent, we prepare here 13 C-enhanced graphene samples that show a large aromatic 12 C= 13 C stretch that reveals this IR-active mode.

01 COAL, LIGNITE, AND PEAT↗

Ultrafast and Controllable Phase Evolution by Flash Joule Heating

Flash Joule heating (FJH), an advanced material synthesis technique, has been used for the production of high-quality carbon materials. Direct current discharge through the precursors by large capacitors has successfully converted carbon-based starting materials into bulk quantities of turbostratic graphene by the FJH process. However, the formation of other carbon allotropes, such as nanodiamonds and concentric carbon materials, as well as the covalent functionalization of different carbon allotropes by the FJH process, remains challenging. Here, we report the solvent-free FJH synthesis of three different fluorinated carbon allotropes: fluorinated nanodiamonds, fluorinated turbostratic graphene and fluorinated concentric carbon. This is done by millisecond flashing of organic fluorine compounds and fluoride precursors. Spectroscopic analysis confirms the modification of the electronic states and the existence of various short-range and long-range orders in the different fluorinated carbon allotropes. As a result, the flash time-dependent relationship is further demonstrated to control the phase evolution and product compositions.

01 COAL, LIGNITE, AND PEAT↗

Plastic Waste Product Captures Carbon Dioxide in Nanometer Pores

We discuss, plastic waste (PW) and increasing atmospheric carbon dioxide (CO 2 ) levels are among the top environmental concerns presently facing humankind. With an ambitious 2050 zero-CO 2 emissions goal, there is a demand for economical CO 2 capture routes. Here we show that the thermal treatment of PW in the presence of potassium acetate yields an effective carbon sorbent with pores width of 0.7–1.4 nm for CO 2 capture. The PW to carbon sorbent process works with single or mixed streams of polyolefin plastics. The CO 2 capacity of the sorbent at 25 °C is 17.0 ± 1.1 wt % (3.80 ± 0.25 mmol g –1 ) at 1 bar and 5.0 ± 0.6 wt % (1.13 ± 0.13 mmol g –1 ) at 0.15 bar, and it regenerates upon reaching 75 ± 5 °C. The CO 2 capture cost from flue gas via this technology is estimated to be <$21 ton –1 CO 2 , much lower than competing CO 2 capture technologies. Hence, this PW-derived carbon material should find utility in the capture of CO 2 from point sources of high CO 2 emissions while providing a use for otherwise deleterious PW.

01 COAL, LIGNITE, AND PEAT↗

Heteroatom-Doped Flash Graphene

Heteroatom doping can effectively tailor the local structures and electronic states of intrinsic two-dimensional materials, and endow them with modified optical, electrical, and mechanical properties. Recent studies have shown the feasibility of preparing doped graphene from graphene oxide and its derivatives via some post-treatments, including solid-state and solvothermal methods, but they require reactive and harsh reagents. However, direct synthesis of various heteroatom-doped graphene in larger quantities and high purity through bottom-up methods remains challenging. Here, we report catalyst-free and solvent-free direct synthesis of graphene doped with various heteroatoms in bulk via flash Joule heating (FJH). Seven types of heteroatom-doped flash graphene (FG) are synthesized through millisecond flashing, including single-element-doped FG (boron, nitrogen, oxygen, phosphorus, sulfur), two-element-co-doped FG (boron and nitrogen), as well as three-element-co-doped FG (boron, nitrogen, and sulfur). Here, a variety of low-cost dopants, such as elements, oxides, and organic compounds are used. The graphene quality of heteroatom-doped FG is high, and similar to intrinsic FG, the material exhibits turbostraticity, increased interlayer spacing, and superior dispersibility. Electrochemical oxygen reduction reaction of different heteroatom-doped FG is tested, and sulfur-doped FG shows the best performance. Lithium metal battery tests demonstrate that nitrogen-doped FG exhibits a smaller nucleation overpotential compared to Cu or undoped FG. The electrical energy cost for the synthesis of heteroatom-doped FG synthesis is only 1.2 to 10.7 kJ g –1 , which could render the FJH method suitable for low-cost mass production of heteroatom-doped graphene.

01 COAL, LIGNITE, AND PEAT↗

Processing and characterization of Ultrathin carbon coatings on glass

Ultrathin carbon layers, on the order of 3-6 nm in thickness, were formed on glass substrates by spin coating and pyrolysis of polymer precursors. The organic precursors used were poly(furfuryl alcohol), coal tar pitch, and a photoresist. The carbon coatings were characterized by ellipsometry, optical profilometry, water contact angle, confocal Raman spectroscopy, UV-vis spectroscopy, and atomic force microscopy. We also report the transparency, hydrophobicity, friction, weathering resistance, and electrical conductivity of the carbon-coated glass. The results reveal that up to 97% transparent, ultrathin carbon films could be formed on glass substrates with a root-mean-square roughness of less than about to 0.3 nm. This carbon layer modified the otherwise hydrophilic surface of the glass to yield a water contact angle of 85{sup o}. The coatings were also found to provide a water barrier against weathering under hot and humid conditions. A 4.5-nm-thick carbon film on glass had a sheet resistance of 55.6 k {Omega} m and a conductivity of 40 S/cm.

01 COAL, LIGNITE, AND PEAT↗

The foul side of 'clean coal'

As power plants face new air pollution control, ash piles and their environmental threats are poised to grow. Recent studies have shown that carcinogens and other contaminants in piles of waste ash from coal-fired power plants can leach into water supplies at concentrations exceeding drinking water standards. Last year an ash dam broke at the 55-year old power plant in Kingston, TN, destroying homes and rising doubts about clean coal. Despite the huge amounts of ash generated in the USA (131 mtons per year) no federal regulations control the fate of ash from coal-fired plants. 56% of this is not used in products such as concrete. The EPA has found proof of water contamination from many operating ash sites which are wet impoundments, ponds or reservoirs of some sort. Several member of Congress have show support for new ash-handling requirements and an inventory of waste sites. Meanwhile, the Kingston disaster may well drive utilities to consider dry handling. 3 photos.

01 COAL, LIGNITE, AND PEAT↗

Chemicals to help coal come clean

Scrubbing methods to capture carbon from power plants are advancing to the demonstration phase. The article gives an update of projects around the world, and the goals and cost of CCS projects. BASF, together with RWE Power and Linde, are working to ensure state of the art integration of the carbon-capture process into a power plant to minimize the penalty in electrical output. A pilot project will test new solvents in an 'advanced amine' system at RWE's power station in Niederaussem, Germany. A pilot unit will soon capture CO{sub 2} from a coal-fired plant of Dow's in South Charleston, WV, USA and Dow has also agreed to build an amines demonstration facility in Belchatow, Poland. Other projects in the USA and Canada are reported. 1 fig.

01 COAL, LIGNITE, AND PEAT↗

Proximate analysis of coal

This lab experiment illustrates the use of thermogravimetric analysis (TGA) to perform proximate analysis on a series of coal samples of different rank. Peat and coke are also examined. A total of four exercises are described. These are dry exercises as students interpret previously recorded scans. The weight percent moisture, volatile matter, fixed carbon, and ash content are determined for each sample and comparisons are made. Proximate analysis is performed on a coal sample from a local electric utility. From the weight percent sulfur found in the coal (determined by a separate procedure the Eschka method) and the ash content, students calculate the quantity of sulfur dioxide emissions and ash produced annually by a large coal-fired electric power plant.

01 COAL, LIGNITE, AND PEAT↗

Comparative investigation on chemical looping combustion of coal-derived synthesis gas containing H2S over supported NiO oxygen carriers

Chemical looping combustion (CLC) of simulated coal-derived synthesis gas was conducted with NiO oxygen carriers supported on SiO2, ZrO2, TiO2, and sepiolite. The effect of H2S on the performance of these samples for the CLC process was also evaluated. Five-cycle thermogravimetric analysis (TGA) tests at 800 C indicated that all oxygen carriers had a stable performance at 800 C, except NiO/SiO2. Full reduction/oxidation reactions of the oxygen carrier were obtained during the five-cycle test. It was found that support had a significant effect on reaction performance of NiO both in reduction and oxidation rates. The reduction reaction was significantly faster than the oxidation reaction for all oxygen carriers, while the oxidation reaction is fairly slow due to oxygen diffusion on NiO layers. The reaction profile was greatly affected by the presence of H2S, but there was no effect on the capacity due to the presence of H2S in synthesis gas. The presence of H2S decreased reduction reaction rates significantly, but oxidation rates of reduced samples increased. X-ray diffraction (XRD) data of the oxidized samples after a five-cycle test showed stable crystalline phases without any formation of sulfides or sulfites/sulfates. Increase in reaction temperature to 900 C had a positive effect on the performance.

01 COAL, LIGNITE, AND PEAT↗

Evaluating the combustion reactivity of drop tube furnace and thermogravimetric analysis coal chars with a selection of metal additives

Opportunities exist for effective coal combustion additives that can reduce the carbon content of pulverized fuel ash (PFA) to below 6%, thereby making it saleable for filler/building material applications without the need for postcombustion treatment. However, with only limited combustion data currently available for the multitude of potential additives, catalytic performance under pulverized fuel (PF) boiler conditions has received relatively little attention. This paper therefore compares the reactivity of catalyzed bituminous coal chars from thermogravimetric analysis (TGA) with those generated by devolatilization in a drop tube furnace (DTF). The principal aim was to explore the fundamental chemistry behind the chosen additives' relative reactivities. Accordingly, all eight of the investigated additives increased the TGA burnout rate of the TGA and DTF chars, with most of the catalysts demonstrating consistent reactivity levels across chars from both devolatilization methods. Copper(I) chloride, silver chloride, and copper nitrate were thus identified as the most successful additives tested, but it proved difficult to establish a definitive reactivity ranking. This was largely due to the use of physical mixtures for catalyst dispersion, the relatively narrow selection of additives examined, and the inherent variability of the DTF chars. Nevertheless, one crucial exception to normal additive behavior was discovered, with copper(I) chloride perceptibly deactivating during devolatilization in the DTF, even though it remained the most effective catalyst tested. As a prolonged burnout at over 1000{sup o}C was required to replicate this deactivation effect on the TGA, the phenomenon could not be detected by typical testing procedures. Subsequently, a comprehensive TGA study showed no obvious relationship between the catalyst-induced reductions in the reaction's apparent activation energy and the samples recorded burnout rates.

01 COAL, LIGNITE, AND PEAT↗

Speciation of Selenium, Arsenic, and Zinc in Class C Fly Ash

A major environmental concern associated with coal fly ash is the mobilization of trace elements that may contaminate water. To better evaluate proper use of fly ash, determine appropriate disposal methods, and monitor postdisposal conditions, it is important to understand the speciation of trace elements in fly ash and their possible environmental impact. The speciation of selenium, arsenic, and zinc was determined in five representative Class C fly ash samples from combustion of sub-bituminous Powder River Basin coal using synchrotron-based X-ray absorption spectroscopy to provide an improved understanding of the mechanisms of trace element association with the fly ash. Selenium in all fly ash samples occurs predominantly as Se(IV), with the exception of one sample, in which there was a minor amount of Se(0). Se(0) is likely associated with the high content of unburned coal in the sample. Arsenic exists in the fly ash as a single phase most consistent with calcium pyroarsenate. In contrast, zinc occurs as two distinct species in the silicate glass matrix of the fly ash. This work demonstrates that residual carbon in fly ash may reduce potential Se mobility in the environment by retaining it as less soluble elemental Se instead of Se(IV). Further, this work suggests that As and Zn in Class C fly ash will display substantially different release and mobilization behaviors in aquatic environments. While As release will primarily depend upon the dissolution and hydrolysis of calcium pyroarsenate, Zn release will be controlled by the dissolution of alkaline aluminosilicate glass in the ash.

01 COAL, LIGNITE, AND PEAT↗

Pore accessibility by methane and carbon dioxide in coal as determined by neutron scattering

Contrast-matching ultrasmall-angle neutron scattering (USANS) and small-angle neutron scattering (SANS) techniques were used for the first time to determine both the total pore volume and the fraction of the pore volume that is inaccessible to deuterated methane, CD{sub 4}, in four bituminous coals in the range of pore sizes between {approx}10 {angstrom} and {approx}5 {micro}m. Two samples originated from the Illinois Basin in the U.S.A., and the other two samples were commercial Australian bituminous coals from the Bowen Basin. The total and inaccessible porosity were determined in each coal using both Porod invariant and the polydisperse spherical particle (PDSP) model analysis of the scattering data acquired from coals both in vacuum and at the pressure of CD{sub 4}, at which the scattering length density of the pore-saturating fluid is equal to that of the solid coal matrix (zero average contrast pressure). The total porosity of the coals studied ranged from 7 to 13%, and the volume of pores inaccessible to CD{sub 4} varied from {approx}13 to {approx}36% of the total pore volume. The volume fraction of inaccessible pores shows no correlation with the maceral composition; however, it increases with a decreasing total pore volume. In situ measurements of the structure of one coal saturated with CO{sub 2} and CD{sub 4} were conducted as a function of the pressure in the range of 1-400 bar. The neutron scattering intensity from small pores with radii less than 35 {angstrom} in this coal increased sharply immediately after the fluid injection for both gases, which demonstrates strong condensation and densification of the invading subcritical CO{sub 2} and supercritical methane in small pores.

01 COAL, LIGNITE, AND PEAT↗

Effects of Measurement Materials and Oxygen Partial Pressure on the Viscosity of synthetic Eastern and Western United States Coal Slags

The viscosity of the molten ash (slag) resulting from the mineral constituents in carbon feedstock used in slagging gasifiers is critical for controlling the gasification process. The viscosity of two synthetic slags with compositions resembling the mineral impurities in average eastern and western coal feedstock was examined at temperatures from 1300–1500 °C using a rotating bob viscometer. A few combinations of atmospheres and experimental materials were investigated with respect to one another to determine slag viscosity. A CO/CO{sub 2} atmosphere (CO/CO{sub 2} = 1.8, corresponding to a P{sub O{sub 2}} = 10–8 atm) is required to sustain ferrous ions in FeO-containing slags, an environment that is oxidizing to most metals. Iron oxide in the slag prevents usage of Fe parts. In unpurified Ar, the Fe metal surface oxidizes. Using purified argon prevents iron measurement components from oxidation; however, the metallic surfaces act as nucleation sites for the reduction of the Fe oxide in the slag into metallic Fe. Dissolution of ceramic materials into the slag, including Al{sub 2}O{sub 3} and ZrO{sub 2}, occurs in both atmospheres. Therefore, evaluating slag properties in the laboratory is challenging. The measured viscosities of two synthetic slags in this study diverged depending upon material selection. This difference is likely attributable to container/spindle-slag interactions. Viscosity measurements of the eastern coal slag using all ceramic parts agreed best with FactSage prediction above 1350 °C, with an average activation energy of 271.2 kJ. For western coal slag, the dissolution of container/spindle materials was substantial during the measurement, with precipitation of crystalline phase noted. The experimental viscosity data of the western coal slag agreed best with Kalmanovitch prediction above 1350 °C. The activation energy changed dramatically for both data sets of western coal slag, likely indicating the Newtonian-to-non-Newtonian transition.

01 COAL, LIGNITE, AND PEAT↗

Porosity of coal and shale: Insights from gas adsorption and SANS/USANS techniques

Two Pennsylvanian coal samples (Spr326 and Spr879-IN1) and two Upper Devonian-Mississippian shale samples (MM1 and MM3) from the Illinois Basin were studied with regard to their porosity and pore accessibility. Shale samples are early mature stage as indicated by vitrinite reflectance (R{sub o}) values of 0.55% for MM1 and 0.62% for MM3. The coal samples studied are of comparable maturity to the shale samples, having vitrinite reflectance of 0.52% (Spr326) and 0.62% (Spr879-IN1). Gas (N{sub 2} and CO{sub 2}) adsorption and small-angle and ultrasmall-angle neutron scattering techniques (SANS/USANS) were used to understand differences in the porosity characteristics of the samples. The results demonstrate that there is a major difference in mesopore (2-50 nm) size distribution between the coal and shale samples, while there was a close similarity in micropore (<2 nm) size distribution. Micropore and mesopore volumes correlate with organic matter content in the samples. Accessibility of pores in coal is pore-size specific and can vary significantly between coal samples; also, higher accessibility corresponds to higher adsorption capacity. Accessibility of pores in shale samples is low.

01 COAL, LIGNITE, AND PEAT↗

Steam-Coal Gasification Using CaO and KOH for in Situ Carbon and Sulfur Capture

We present experimental results of coal gasification with and without the addition of calcium oxide and potassium hydroxide as dual-functioning catalyst-capture agents. Using two different coal types and temperatures between 700 and 900 °C, we studied the effect of these catalyst-capture agents on (1) the syngas composition, (2) CO 2 and H 2 S capture, and (3) the steam-coal gasification kinetic rate. The syngas composition from the gasifier was roughly 20% methane, 70% hydrogen, and 10% other species when a CaO/C molar ratio of 0.5 was added. We demonstrated significantly enhanced steam–coal gasification kinetic rates when adding small amounts of potassium hydroxide to coal when operating a CaO-CaCO 3 chemical looping gasification reactor. For example, the steam–coal gasification kinetic rate increased 250% when dry mixing calcium oxide at a Ca/C molar ratio of 0.5 with a sub-bituminous coal, and the kinetic rate increased 1000% when aqueously mixing calcium oxide at a Ca/C molar ratio of 0.5 along with potassium hydroxide at a K/C molar ratio of 0.06. In addition, we conducted multi-cycle studies in which CaCO 3 was calcined by heating to 900 °C to regenerate the CaO, which was then reused in repeated CaO-CaCO 3 cycles. The increased steam-coal gasification kinetics rates for both CaO and CaO + KOH persisted even when the material was reused in six cycles of gasification and calcination. The ability of CaO to capture carbon dioxide decreased roughly 2-4% per CaO-CaCO 3 cycle. We also discuss an important application of this combined gasifier-calciner to electricity generation and selling the purge stream as a precalcined feedstock to a cement kiln. In this scenario, the amount of purge stream required is fixed not by the degradation in the capture ability but rather by the requirements at the cement kiln on the amount of CaSO 4 and ash in the precalcined feedstock.

01 COAL, LIGNITE, AND PEAT↗

Steam Gasification Rates of Three Bituminous Coal Chars in an Entrained-Flow Reactor at Pressurized Conditions

Three bituminous coal chars (Illinois #6, Utah Skyline, and Pittsburgh #8) were gasified separately at total pressures of 10 and 15 atm in an entrained-flow reactor using gas temperatures up to 1830 K and particle residence times <240 ms. The experiments were performed at conditions where the majority of particle mass release was due to H 2 O gasification, although select experiments were performed at conditions where significant mass release was due to gasification by both H 2 O and CO 2 . The measured coal data we recorded were fit to three char gasification models including a simple first-order global model, as well as the CCK N and CCK models that stem from the CBK model. The optimal kinetic parameters for each of the three models are reported, and the steam reactivity of the coal chars at the studied conditions is as follows: Pittsburgh #8 > Utah Skyline > Illinois #6.

01 COAL, LIGNITE, AND PEAT↗