Search NASA⌕ Search

SEARCH · Search NASA

Results for “Membrane Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

A Comparison of Flow-Through Versus Non-Flow-Through Proton Exchange Membrane Fuel Cell Systems for NASA's Exploration Missions

As part of the Exploration Technology Development Program (ETDP) under the auspices of the Exploration Systems Mission Directorate (ESMD), NASA is developing both primary fuel cell power systems and regenerative fuel cell (RFC) energy storage systems within the fuel cell portion of the Energy Storage Project. This effort is being led by the NASA Glenn Research Center (GRC) in partnership with the NASA Johnson Space Center (JSC), Jet Propulsion Laboratory (JPL), NASA Kennedy Space Center (KSC), and industrial partners. The development goals are to improve fuel cell and electrolysis stack electrical performance, reduce system mass, volume, and parasitic power requirements, and increase system life and reliability. A major focus of this effort has been the parallel development of both flow-through and non-flow-through proton exchange membrane (PEM) primary fuel cell power systems. The plan has been, at the appropriate time, to select a single primary fuel cell technology for eventual flight hardware development. Ideally, that appropriate time would occur after both technologies have achieved a technology readiness level (TRL) of six, which represents an engineering model fidelity PEM fuel cell system being successfully tested in a relevant environment. Budget constraints in fiscal year 2009 and beyond have prevented NASA from continuing to pursue the parallel development of both primary fuel cell options. Because very limited data exists for either system, a toplevel, qualitative assessment based on engineering judgement was performed expeditiously to provide guidance for a selection. At that time, the non-flow-through technology was selected for continued development because of potentially major advantages in terms of weight, volume, parasitic power, reliability, and life. This author believes that the advantages are significant enough, and the potential benefits great enough, to offset the higher state of technology readiness of flow-through technology. This paper summarizes the technical considerations which helped form the engineering judgement that led to the final decision.

Hoberecht, Mark A.↗
DOE OSTI2021

Recent advances in CO 2 hydrogenation to value-added products — Current challenges and future directions

Climate change, global warming, fossil fuel depletion and rising fuel prices have created great incentives to seek alternative fuel production technologies. CO 2 transformation to value-added products using renewable H 2 has proven to be an emerging solution to enable this goal. In this regard, three different promising processes, namely methane, methanol and hydrocarbon synthesis via CO 2 hydrogenation are thoroughly discussed. In addition, the influential factors affecting process efficiencies such as catalyst design and mechanistic insight, operating conditions as well as reactor types are investigated, with key pathways that dictate catalyst activity and selectivity of the most promising materials described. Furthermore, a brief overview of the reactor configuration and its crucial role in the improving process viability is analyzed. Accordingly, fixed-bed, fluidized-bed, annular and spherical reactors along with H 2 O/H 2 perm-selective membrane reactors are disscussed for hydrocarbon production. In addition, different reactor configurations are compared to assess the best one that is adjustable depending on the reaction mechanism. In conclusion, a corrugated-wall dual-type membrane reactor is proposed as an emerging alternative for CO 2 hydrogenation to value-added products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Developing novel electrodes with ultralow catalyst loading for high-efficiency hydrogen production in proton exchange membrane electrolyzer cells

Hydrogen plays more crucial roles for decarbonizing the planets and meeting the climate challenges because of its high energy density and zero-emission. It can be produced with proton exchange membrane electrolyzer cells (PEMECs) driven by sustainable and renewable energy resources. Although PEMECs have a number of advantages, including high purity production, quick response, and the ability to operate at high pressure facilitating the gas delivering, their performance and cost greatly hinder their commercial-scale applications. To achieve high-efficiency and cost-reduced hydrogen production in PEMECs, we proposed thin engineered liquid/gas diffusion layers (LGDLs) and associated electrodes, i.e., catalyst-coated LGDLs (CCLGDLs), over conventional porous transport layers (PTLs) and catalyst-coated membranes (CCMs). The research approaches in this project are based on material synthesis, in-situ and ex-situ characterizations, component design and treatment, numerical modeling, and cost analysis. The thin and tunable LGDLs (TT-LGDLs) and CCLGDLs were successfully developed with great performance improvement as demonstrated in lab-scale, bench-scale, and system-scale electrolyzer tests. The electrode thickness was reduced from 370 µm to less than 100 µm with simplified fabrication processes. With the catalytically enhanced Ir-based catalyst coating, the as-developed CCLGDLs with a catalyst loading of 0.34 mg Ir /cm 2 achieved a cell performance of 1.77 V at 2 A cm -2 , exhibiting the catalyst mass activity enhanced by >20 times with significant catalyst saving over conventional catalyst cell design. In-situ PEMEC characterizations, including the current distribution mapping and high-speed and multiscale visualizations, were conducted for a deeper understanding of mass transport and electrochemical reactions within an electrolyzer with LGDLs and CCLGDLs. A 2D cell model was developed and validated for the enhanced performance on TT-LGDL through reducing ohmic losses due to nonuniform hydration and water transport. Further, the cost analysis results have shown a path to move beyond equivalency and surpass costs associated with the project baseline. In this project, the design and fabrication of TT-LGDLs and CCLGDLs will contribute to the performance enhancement, manufacturing simplification, and cost reduction for PEMECs and other energy conversion devices, thus shortening their pathways towards commercialization. This project also provides a good foundation for furthering the in-situ reaction interface research.

08 HYDROGEN↗
DOE OSTI2026

Impact of Porous Transport Layer In-Plane Conduction on Spatially Resolved Current and EIS Measurements in a Proton Exchange Membrane Water Electrolyzer

An XY segmented cell was developed for low temperature PEM water electrolysis (PEMWE). The system can assess the local performance by enabling in situ measurements of spatial currents and impedances. In this work, we show through experiments, as well as through modelling work, that the porous transport layer (PTL) must be segmented to eliminate crosstalk. Accurate measurements are only possible when crosstalk is fully eliminated. The XY segmented cell is applied to a case study characterizing the impact of a PTL platinum coating void on spatial performance. The localized performance impact of the coating void is found to be orientation specific: coating voids facing the catalyst layer reduce performance significantly more than coating voids facing the flow field. The results suggest that the tolerances for PTL coating uniformity can be lower at the side facing the flow field. The work showcases the feasibility of the XY segmented cell for impact assessment studies. The presented XY segmented cell enables the characterization of spatial phenomena in PEMWE devices and is envisioned to support modeling efforts and the investigation of manufacturing related tolerances for mass produced PEMWE devices.

08 HYDROGEN↗
NASA NTRS1988

A model to predict the removal of oxygen from air using a zirconia solid electrolyte membrane

A finite difference mathematical model has been developed to predict the removal of oxygen from air using a zirconia separation cell. The model predicts the electrical and mass transfer processes in circular disk cells with either axial or radial current flow in the electrodes and in tubular cells with axial current flow in the electrodes. Representative results are presented and discussed.

Marner, W. J.↗
NASA NTRS2015

Continued Advancement of Supported Liquid Membranes for Carbon Dioxide Control in Extravehicular Activity Applications

The Development of a new, robust, portable life support system (PLSS) is currently a high NASA priority in order to support longer and safer extravehicular activity (EVA) missions that will be necessary as space travel extends to near-Earth asteroids and eventually Mars. One of the critical PLSS functions is maintaining the carbon dioxide (CO2) concentration in the suit at acceptable levels. The Metal Oxide (MetOx) canister has a finite CO2 adsorption capacity and therefore in order to extend mission times, the unit would have to be larger and heavier, which is undesirable; therefore new CO2 control technologies must be developed. While recent work has centered on the use of alternating sorbent beds that can be regenerated during the EVA, this strategy increases the system complexity and power consumption. A simpler approach is to use a membrane that vents CO2 to space but retains oxygen(O2). A membrane has many advantages over current technology: it is a continuous system with no theoretical capacity limit, it requires no consumables, and it requires no hardware for switching beds between absorption and regeneration. Conventional gas separation membranes do not have adequate selectivity for use in the PLSS, but the required performance could be obtained with a supported liquid membrane (SLM), which consists of a microporous film filled with a liquid that selectively reacts with CO2 over oxygen (O2). In a recently completed Phase II Small Business Innovative Research project, Reaction Systems developed a new reactive liquid that has effectively zero vapor pressure, making it an ideal candidate for use in an SLM. Results obtained with the SLM in a flat sheet configuration with representative pressures of CO2, O2, and water (H2O) have shown that the CO2 permeation rate and CO2/O2 selectivity requirements have been met. In addition, the SLM vents moisture to space very effectively. The SLM has also been prepared and tested in a hollow fiber form, which will be necessary to meet size requirements in the PLSS. In initial tests, the required CO2 permeance values have been obtained, while the current CO2/O2 selectivity values are somewhat lower than needed. However, the performance of the SLM is a strong function of the method used to impregnate the sorbent in the hollow fiber walls and rapid progress is being made in that area.

Wickham, David T.↗
NASA NTRS2004

Innovative Structural Design Features for a 10 m Solar Sail Demonstrator

The successful development of sail architectures will require careful attention to a number of key issues including but not limited to material strength issues, stress conditions for the membrane, load interactions between membrane and structure, and membrane material planarity. Along with the inherent challenges of fabricating and handling very large membrane structures these issues will pose real challenges for the near-term development of practical sail technologies. SRS has developed innovative technologies that deal directly with the challenges of developing very large sail membranes. Some of these technologies include edge reinforcements and innovative reinforcement attachment techniques, production of flight durable sail materials of less than 2.5 micron thicknesses and large scale fabrication techniques. SRS has employed these technologies in several large 10 m demonstrators that have been delivered to LaRC for solar vacuum testing. Details of the design of this system will be discussed.

Laue, G.↗
DOE OSTI2026

Synaptic Functionality and Neuromorphic Information Processing in Membrane Ion Channel Junctions

The human brain performs complex memory and computational tasks with high energy efficiency by regulating ion transport through membrane channels. These signaling mechanisms have been inspiring the development of nanofluidic memristors that emulate synaptic behavior. Here, in this study, we describe a membrane ion channel synapse (MICS), constructed from aqueous droplets linked by gramicidin A channels, that achieves neuromorphic functionality. MICS exhibits memristive ion transport with hysteretic current–voltage behavior arising from voltage-dependent channel formation and ion transport dynamics. MICS emulates a range of synaptic behaviors including associative learning. We further demonstrate its application in reservoir computing by performing handwritten digit classification and tic-tac-toe game and explore the system parameters that improve the computational performance. This droplet-based biomimetic synapse offers a potentially scalable and energy-efficient platform for next-generation neuromorphic computing systems.

Droplet interface bilayer↗
DOE OSTI2023

Update on MEA AST [Slides]

Goals: Developing MEA ASTs for Heavy Duty Applications: 1) New protocol published within M2FCT in Nov 2022; 2) Work is ongoing to understand the degradation rates of SOA (State of the Art) materials; 3) The protocol will be updated (If needed) by the end of the Fiscal Year (Sept 2023). Updating component specific ASTs: 1) Catalyst AST: Extend from 30K cycles to 90K cycles to reflect LDV and HDV lifetimes of 5000 (8000 hours) and 25000 (30000 hours); 2) Catalyst Supports: Quantifying carbon corrosion during H 2 /Air AST using NDIR; 3) Membrane Degradation: Membrane thinning and FER measurement. Validating developed ASTs with modeled drive cycles and experiments.

08 HYDROGEN↗
NASA NTRS1996

Cellular responses to endogenous electrochemical gradients in morphological development

Endogenous electric fields give vectorial direction to morphological development in Zea mays (sweet corn) in response to gravity. Endogenous electrical fields are important because of their ability to influence: (1) intercellular organization and development through their effects on the membrane potential, (2) direct effects such as electrophoresis of membrane components, and (3) both intracellular and extracellular transport of charged compounds. Their primary influence is in providing a vectorial dimension to the progression of one physiological state to another. Gravity perception and transduction in the mesocotyl of vascular plants is a complex interplay of electrical and chemical gradients which ultimately provide the driving force for the resulting growth curvature called gravitropism. Among the earliest events in gravitropism are changes in impedance, voltage, and conductance between the vascular stele and the growth tissues, the cortex, in the mesocotyl of corn shoots. In response to gravistimulation: (1) a potential develops which is vectorial and of sufficient magnitude to be a driving force for transport between the vascular stele and cortex, (2) the ionic conductance changes within seconds showing altered transport between the tissues, and (3) the impedance shows a transient biphasic response which indicates that the mobility of charges is altered following gravistimulation and is possibly the triggering event for the cascade of actions which leads to growth curvature.

Desrosiers, M. F.↗
NASA NTRS2004

New Hydrophilic, Composite Membranes for Air Removal from Water Coolant Systems

Liquid coolants are commonly used as thermal transport media to increase efficiency and flexibility in aerospace vehicle design. The introduction of gas bubbles into the coolant can have negative consequences, including: loss of centrifugal pump prime, irregular sensor readings, and blockage of coolant flow to remote systems. One solution to mitigate these problems is the development of a passive gas removal device, or gas trap, installed in the flight cooling system. In this study, a new hydrophilic, composite membrane has been developed for passage of the coolant fluid and retention of gas bubbles. The trapped bubbles are subsequently vented from the system by a thin, hydrophobic, microporous membrane. The original design for this work employed a homogeneous membrane that was susceptible to fouling and pore plugging. Spare gas traps of this variety have degraded during storage, and recreation of the membranes has been complicated due to problems with polymer duplication and property variations in the final membranes. In this work, replacements have been developed based on deposition of a hydrophilic polymer on the bore-side of a porous polyethylene (PE) tube. The tube provides excellent chemical and mechanical stability, and the hydrophilic layer provides retention of gas bubbles. Preliminary results have shown that intimate contact is required between the deposited layer and the substrate to overcome material differences. This has been accomplished by presoaking the membrane tube in the solvent to raise its surface energy. Polymer solutions of various concentrations have been used to promote penetration of the polymer layer into the porous substrate and to control separation layer thickness. The resulting composite membranes have shown repeatable decrease in nitrogen permeability, which is indicative of a decrease in membrane pore size. Studies with water permeation have yielded similar results. We have observed some swelling of the added polymer layer, which causes a slight decrease in membrane pore size, and should result in improved bubble retention. Preliminary studies have also been performed on gas retention in flowing systems. Initial results have been promising, with negligible gas permeation for the coated membranes compared to 100% gas permeation in the uncoated tube.

Ritchie, Stephen M. C.↗
DOE OSTI2025

Catalytic Difunctionalization of Cyclic Dienes: Direct Entry to Novel ROMP Monomers

We developed a catalytic platform to convert simple hydrocarbon feedstocks into valuable, tunable materials by leveraging nickel-catalyzed difunctionalization of cyclic dienes to access a novel class of cyclic alkene monomers. These monomers undergo ring-opening metathesis polymerization (ROMP) to yield sequence-controlled polymers with defined stereochemistry. Through mechanistic studies and catalyst optimization, we established a scalable, gram-level synthesis for selective diarylation, and expanded the reaction scope to include arylalkylation through rationally tuning the organoboron coupling partner. The resulting polymers were systematically studied to understand how steric, electronic, and stereochemical features influence polymerization behavior and bulk material properties. Functionalized derivatives bearing sulfonated groups were explored as proton-exchange membranes, and chemical recycling pathways were developed to recover monomers from the final materials. This work bridges small-molecule catalysis and macromolecular design, enabling access to tunable, recyclable polymers from abundant hydrocarbon starting materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of a Hybrid Carbon Capture System at a NGCC Power Plant That Performs Direct Air Capture During Off-Peak Hours

The goal of this project was to investigate the feasibility of coupling NGCC power plants with membrane and solid sorbent carbon capture to achieve net negative carbon emissions. This novel hybrid system has a couple of potential benefits: 1) the carbon capture systems could help the NGCC plant by minimizing its carbon footprint and giving it a new revenue stream from direct air capture, and 2) the NGCC plant could help direct air capture scale up quickly and costeffectively by providing it with electricity, steam and compressed air streams. In order to investigate this hybrid design, we developed a complex, integrated system model consisting of: 1) a NGCC power plant model developed by Dr. Bhattacharyya’s team at WVU, 2) a membrane carbon capture model developed by Dr. Lipscomb’s team at U Toledo, and 3) a solid sorbent carbon capture model developed by Dr. Hornbostel’s team at U Pittsburgh. Mr. Matuszewski’s team at AristoSys LLC integrated these three models into a single, integrated model using FOQUS, an optimization tool developed by the NETL CCSI 2 program. Optimizations were then performed on this integrated model to determine the cost and carbon capture rates under a range of electricity and carbon price scenarios.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Assessing the Oxidative Stability of Anion Exchange Membranes in Oxygen Saturated Aqueous Alkaline Solutions

While anion exchange membrane water electrolyzers show promise as a source of green hydrogen using low-temperatures and non-platinum group metal catalysts, many concerns must be addressed. A primary challenge for the development of high-performance anion exchange membrane water electrolyzers is the fabrication of a stable membrane that will be able to survive long-term stability test while maintaining high anion conductivity, which is a necessity for a durable water electrolyzer. This method will present a standardized protocol that can be used by researchers to assess the quality of their AEM materials and be able to provide insight into how materials may be degrading and how to improve the quality of AEMs. Using Mohr or Volhard titration to measure ion-exchange capacity, EIS to determine the ionic conductivity, NMR and FTIR to understand the extent of membrane degradation over time, and mechanical analyzers to determine the strength of their AEMs, this standardized protocol will guide researchers to determining and improving upon the long-term durability and performance of their AEM materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Final Technical Report for project entitled Highly Active, Durable, and Ultra-Low PGM NSTF Thin Film ORR Catalysts and Support

In this project, the objective was to develop new oxygen reduction reaction (ORR) electrocatalysts for proton exchange membrane fuel cells (PEMFCs) which could exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001224, Subtopic 1b, Table I. The expected outcome was development of one or more electrocatalysts which are substantially improved over the current state-of-the-art in terms of overall activity, durability, and cost, and are suitable for automotive traction and stationary fuel cell applications. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of key findings and conclusions. The development activities towards new highly active and durable thin film electrocatalysts has led to the discovery of several electrocatalysts which approached or exceeded several DOE 2020 targets for activity, durability, and performance in proton exchange membrane fuel cell (membrane electrode assemblies (MEAs). In this project, electrocatalyst development focused on systematic physical and electrochemical characterization of electrocatalyst activity, durability, and performance in MEAs as a function of electrocatalyst fabrication, compositional and structural variables. The project approach was to develop relationships between the catalyst functional responses (activity, durability and performance) with catalyst physical properties and catalyst fabrication methods. Additionally, the thin film catalysts were integrated onto the unique and durable 3M Nanostructured Thin Film (NSTF) support, consisting of arrays of self-assembled organic crystalline whiskers. The catalysts were evaluated against the project targets via extensive electrochemical characterization in MEA format at 3M, advanced structural and compositional microscopy at Oak Ridge National Laboratory (ORNL), and atomic structure analysis via XAFS at Argonne National Laboratory (ANL). The extensive electrochemical and physical characterization resulted in development of several trends which correlate the catalysts’ electrochemical properties to their physical properties, including composition, structure, and method of fabrication. The development was guided by density functional theory (DFT) modeling at Purdue University and kinetic Monte Carlo (kMC) modeling at Johns Hopkins University. The catalyst simulations provided key insights into the observed experimental activity and durability trends, and additionally were utilized to assess new electrocatalyst concepts prior to or coincident with physical catalyst development. This development has led to several electrocatalyst candidates with activity and durability which approach or exceed DOE targets. One class of catalysts, based on nm-scale thin layers of Pt on Ir, met or exceeded 6 of the 6 DOE targets the project addressed.

08 HYDROGEN↗
NASA NTRS2011

Pressure Regulator With Internal Ejector Circulation Pump, Flow and Pressure Measurement Porting, and Fuel Cell System Integration Options

An advanced reactant pressure regulator with an internal ejector reactant circulation pump has been developed to support NASA's future fuel cell power systems needs. These needs include reliable and safe operation in variable-gravity environments, and for exploration activities with both manned and un manned vehicles. This product was developed for use in Proton Exchange Membrane Fuel Cell (PEMFC) power plant reactant circulation systems, but the design could also be applied to other fuel cell system types, (e.g., solid-oxide or alkaline) or for other gas pressure regulation and circulation needs. The regulator design includes porting for measurement of flow and pressure at key points in the system, and also includes several fuel cell system integration options. NASA has recognized ejectors as a viable alternative to mechanical pumps for use in spacecraft fuel cell power systems. The ejector motive force is provided by a variable, high-pressure supply gas that travels through the ejector s jet nozzle, whereby the pressure energy of the fluid stream is converted to kinetic energy in the gas jet. The ejector can produce circulation-to-consumption-flow ratios that are relatively high (2-3 times), and this phenomenon can potentially (with proper consideration of the remainder of the fuel cell system s design) be used to provide completely for reactant pre-humidification and product water removal in a fuel cell system. Specifically, a custom pressure regulator has been developed that includes: (1) an ejector reactant circulation pump (with interchangeable jet nozzles and mixer sections, gas-tight sliding and static seals in required locations, and internal fluid porting for pressure-sensing at the regulator's control elements) and (2) internal fluid porting to allow for flow rate and system pressure measurements. The fluid porting also allows for inclusion of purge, relief, and vacuum-breaker check valves on the regulator assembly. In addition, this regulator could also be used with NASA's advanced nonflow-through fuel cell power systems by simply incorporating a jet nozzle with an appropriate nozzle diameter.

Vasquez, Arturo↗
DOE OSTI2026

NiFeCo-based catalysts in high current zero-gap anion exchange membrane water electrolyzers

Understanding degradation mechanisms in pure water anion exchange membrane water electrolyzers is essential for developing durable and precious metal-free hydrogen production systems, yet electronic, chemical, and transport-driven pathways often occur simultaneously at the anode. To separate these effects, we establish a morphology invariant Ni/Fe/Co thin film model catalyst platform using physical vapor deposition and systematically compare composition-dependent behavior under both pure water and 0.1 M KOH feeds. Devices were operated under industrially relevant current density conditions, galvanostatically at 1 A cm −2 for 24 hours; metal dissolution, ionomer oxidation, and resistance growth were quantified using inductively coupled plasma mass spectrometry, X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy. Under pure-water operation, Ni-rich films showed voltage increases that correlated with rising total cell resistance (ΔV ≈ 243 mV, ΔR ≈ 0.17 Ω cm 2 ). Co-rich films maintained near constant voltages with minimal resistance change (ΔV < 10 mV, ΔR ≈ 0.03 Ω cm 2 ) but induced pronounced ionomer oxidation observed by XPS. In 0.1 M KOH, ionomer oxidation is suppressed, and impedance growth is minimized (<0.08 Ω cm 2 ) across all compositions, consistent with reduced transport limitations and improved ionic conduction relative to pure-water feeds. These results demonstrate how a controlled thin film model platform can isolate composition electrolyte relationships and provide mechanistic design principles for stable pure water anion exchange membrane electrolyzers.

Milenia Rojas Mendoza, B. [Stanford Univ., CA (Uni↗
NASA NTRS2010

High-Precision Shape Control of In-Space Deployable Large Membrane/Thin-Shell Reflectors

This innovation has been developed to improve the resolutions of future spacebased active and passive microwave antennas for earth-science remote sensing missions by maintaining surface figure precisions of large membrane/thin-shell reflectors during orbiting. The intention is for these sensing instruments to be deployable at orbit altitudes one or two orders of magnitude higher than Low Earth Orbit (LEO), but still being able to acquire measurements at spatial resolution and sensitivity similar to those of LEO. Because active and passive microwave remote sensors are able to penetrate through clouds to acquire vertical profile measurements of geophysical parameters, it is desirable to elevate them to the higher orbits to obtain orbital geometries that offer large spatial coverage and more frequent observations. This capability is essential for monitoring and for detailed understanding of the life cycles of natural hazards, such as hurricanes, tropical storms, flash floods, and tsunamis. Major components of this high-precision antenna-surface-control system include a membrane/thin shell reflector, a metrology sensor, a controller, actuators, and corresponding power amplifier and signal conditioning electronics (see figure). Actuators are attached to the back of the reflector to produce contraction/ expansion forces to adjust the shape of the thin-material reflector. The wavefront-sensing metrology system continuously measures the surface figure of the reflector, converts the surface figure to digital data and feeds the data to the controller. The controller determines the control parameters and generates commands to the actuator system. The flexible, piezoelectric polymer actuators are thus activated, providing the control forces needed to correct any distortions that exist in the reflector surface. Piezoelectric polymer actuators are very thin and flexible. They can be implemented on the back of the membrane/thin-shell reflector without introducing significant amounts of mass or stiffness to the reflector. They can be rolled up or folded to accommodate the packaging needed for launch. An analytical model of the system, which includes the membrane reflector, actuator, and controller has been developed to investigate the functionality of this control system on a 35-meter-diameter membrane reflector. The performance of this system under external disturbances such as in space thermal loads and W-error due to inflation has been investigated. A subscale breadboard has been developed, and the functionality of this control concept has been demonstrated by this breadboard.

Watkins, Ronald↗