Search NASA⌕ Search

SEARCH · Search NASA

Results for “Optical diffusers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Radiative equilibrium in a rectangular enclosure bounded by gray walls

Two-dimensional temperature and heat-flux distributions are calculated for an absorbing-emitting gray medium at radiative equilibrium in a rectangular enclosure. The bounding walls are gray and diffuse with arbitrary surface-temperature distributions, and heat generation may take place inside the medium. As a first approximation, the problem is solved for optically thick systems (differential approximation). These results are subsequently improved by the introduction of a number of geometrical parameters to yield good accuracy for all optical thicknesses. As examples, two cases are discussed in detail: (1) uniform heat generation in a black enclosure, and (2) an enclosure with one gray surface at constant temperature. Comparison with some numerical solutions generated by Hottel's /Hottel and Cohen (1958) and Einstein (1963)/ zonal method shows excellent agreement.

Modest, M. F.↗
NASA NTRS1976

Aerosol size distributions - Remote determination from air-borne measurements of the solar aureole

Aerosol-size distributions were determined remotely using an airborne scanning photometer. This instrument consists of a sunshade, optics, and a large-dynamic-range photodetector-amplifier system that scans about the vertical, recording both the direct attenuated solar beam and the diffuse sky radiance in the almucantar of the sun at an effective wavelength of 0.54 micron. Inversion of the measured radiances determined aerosol radii from approximately 0.2 to 8.0 microns. Data were taken during flights over western Lake Superior and southwestern Wisconsin. Inverted aerosol-size distributions are compared with results obtained by other methods.

Twitty, J. T.↗
NASA NTRS1987

Growth of Triglycine Sulfate (TGS) crystals aboard Spacelab-3

An experiment to study the growth of single crystals of triglycine sulfate (NH2CH2COOH)3 H2SO4 (TGS) was successfully carried out on the Spacelab-3 mission during April 29 to May 6, 1985. Two crystals of TGS were grown during the flight, using a specially developed cooled sting technique of solution crystal growth. For the first time in any flight experiment the growth was monitored on-board as well as on ground by video-schlieren technique. Hundreds of holograms were taken for the solution/crystal interaction during the growth process. Preliminary results indicate that the optical system worked very well and the quality of reconstructed holograms is satisfactory. The cooled sting technique was successfully demonstrated. Holographic interferograms indicate convection free, diffusion limited growth. Some of the preliminary results of crystal quality are also presented.

Lal, R. B.↗
NASA NTRS1987

A ray tracing model for leaf bidirectional scattering studies

A leaf is modeled as a deterministic two-dimensional structure consisting of a network of circular arcs designed to represent the internal morphology of major species. The path of an individual ray through the leaf is computed using geometric optics. At each intersection of the ray with an arc, the specular reflected and transmitted rays are calculated according to the Snell and Fresnel equations. Diffuse scattering is treated according to Lambert's law. Absorption is also permitted but requires a detailed knowledge of the spectral attenuation coefficients. An ensemble of initial rays are chosen for each incident direction with the initial intersection points on the leaf surface selected randomly. The final equilibrium state after all interactions then yields the leaf bidirectional reflectance and transmittance distributions. The model also yields the internal two dimensional light gradient profile of the leaf.

Brakke, T. W.↗
NASA NTRS1991

Evidence for particle acceleration in AE Aqr from radio and X-ray observations

The novalike cataclysmic variable AE Aquarii shows evidence for radio synchrotron emission from expanding magnetized clouds. The radio and UV flare timescales are similar indicating that the central engine is located close to the white dwarf. A collisionless shock may develop above the polar cap, which may explain the observed temperature. Protons and ions accelerated up to energies of more than 1 TeV can diffuse away from the central engine, enter magnetized clouds, and generate waves which in turn heat and accelerate electrons. An embarrassing situation exists where reprocessed optical and X-ray pulsations (33 s) are observed, but the expected direct X-ray pulse from the white dwarf is absent. The standard theory for CVs cannot explain this, and one possible explanation is that a beam of relativistic protons and ions from the polar cap may give the observed reprocessed optical to X-rays in a thick target fixed in the system.

De Jager, O. C.↗
NASA NTRS1993

Refractive Index Effects on Radiation in an Absorbing, Emitting, and Scattering Laminated Layer

A simple set of equations is derived for predicting temperature radiative energy flow in a two-region semitransparent laminated layer in the limit of zero heat conduction. The composite is heated on its two sides by unequal amounts of incident radiation. The two layers of the composite have different refractive indices, and each material absorbs, emits, and isotropically scatters radiation. The interfaces are diffuse, and all interface reflections are included. To illustrate the thermal behavior that is readily calculated from the equations, typical results an given for various optical thicknesses and refractive indices of the layers. Internal reflections have a substantial effect on the temperature distribution and radiative heat flow.

Siegel, R.↗
NASA NTRS1994

Distributed Optoelectronic Proximity Sensor

Optoelectronic proximity sensor comprises seven identical units functioning together to provide partially redundant data on spatial relationship between sensor and nearby diffusely reflecting surface. Provides data on distance, relative orientation, and curvature of surface. Sensor called "Hexeye" because its units exhibit hexagonal symmetry when viewed along optical axes and mounted together in hexagonal close packing. Because all six arrays of photodetectors in unit measure essentially identical distributions of light in operating mode, each provides redundant information averaged to increase accuracy or used to verify operation of others. Malfunctioning photodector identified, and output ignored or replaced by interpolated value. Developed for use in such robotic applications as noncontact probing or scanning of surfaces, localization and recognition of objects, and guiding "smart" robot hands in grasping objects.

Lee, Sukhan↗
NASA NTRS1989

Fringe Formation in Dual-Hologram Interferometry

A first order geometrical optics treatment of holograms combined with the generation of interference fringes by two point sources is used to describe reference fringe formation in non-diffuse dual-hologram interferometry.

Burner, A. W.↗
NASA NTRS2004

Optical Sensors for Biomolecules Using Nanoporous Sol-Gel Materials

An important consideration for space missions to Mars is the ability to detect biosignatures. Solid-state sensing elements for optical detection of biological entities are possible using sol-gel based biologically active materials. We have used these materials as optical sensing elements in a variety of bioassays, including immunoassays and enzyme assays. By immobilizing an appropriate biomolecule in the sol-gel sensing element, we have successfully detected analytes such as amino acids and hormones. In the case of the amino acid glutamate, the enzyme glutamate dehydrogenase was the immobilized molecule, whereas in the case of the hormone cortisol, an anti-cortisol antibody was immobilized in the sensing element. In this previous work with immobilized enzymes and antibodies, excellent sensitivity and specificity were demonstrated in a variety of formats including bulk materials, thin films and fibers. We believe that the sol-gel approach is an attractive platform for bioastronautics sensing applications because of the ability to detect a wide range of entities such as amino acids, fatty acids, hopanes, porphyrins, etc. The sol-gel approach produces an optically transparent 3D silica matrix that forms around the biomolecule of interest, thus stabilizing its structure and functionality while allowing for optical detection. This encapsulation process protects the biomolecule and leads to a more "rugged" sensor. The nanoporous structure of the sol-gel matrix allows diffusion of small target molecules but keeps larger, biomolecules immobilized in the pores. We are currently developing these biologically active sol-gel materials into small portable devices for on-orbit cortisol detection

Fang, Jonathan↗
NASA NTRS2017

Spontaneous Ignition of Hydrothermal Flames in Supercritical Ethanol Water Solutions

Results are reported from recent tests where hydrothermal flames spontaneously ignited in a Supercritical Water Oxidation (SCWO) Test Cell. Hydrothermal flames are generally categorized as flames that occur when appropriate concentrations of fuel and oxidizer are present in supercritical water (SCW); i.e., water at conditions above its critical point (218 atm and 374 C). A co-flow injector was used to inject fuel, comprising an aqueous solution of 30-vol to 50-vol ethanol, and air into a reactor held at constant pressure and filled with supercritical water at approximately 240 atm and 425 C. Hydrothermal flames auto-ignited and quickly stabilized as either laminar or turbulent diffusion flames, depending on the injection velocities and test cell conditions. Two orthogonal views, one of which provided a backlit shadowgraphic image, provided visual observations. Optical emission measurements of the steady state flame were made over a spectral range spanning the ultraviolet (UV) to the near infrared (NIR) using a high-resolution, high-dynamic-range spectrometer. Depending on the fuel air flow ratios varying degrees of sooting were observed and are qualitatively compared using light absorption comparisons from backlit images.

hydrothermal flame↗
NASA NTRS1992

The lunar environment and its effect on optical astronomy

The Moon's geologic environment features: (1) gravity field one-sixth that of Earth; (2) sidereal rotation period of 27.3 days; (3) surface with greater curvature than Earth's surface (a chord along a 10 km baseline would have a bulge of 7.2 m); (4) seismically and tidally stable platform on which to make astronomical observations (most moonquakes have magnitudes of 1 to 2 on the Richter scale, within the earth's seismic noise, resulting in ground motions only 1 nm); (5) tenuous atmosphere (the total mass at night is only 10(exp 4) kg) that has an optical depth of 10(exp -6) and does not cause wind induced stresses and vibrations on structures; (6) large diurnal temperature variation (100 to 385 K in equatorial regions), which telescopes must be designed to withstand; (7) weak magnetic field, ranging from 3 to 330 x 10(exp -9) T, compared to 3 x 10(exp -5) T on Earth at the equator; (8) surface exposed to radiation, the most dangerous of which are high energy (1 to 100 Mev) particles resulting from solar flares; (9) high flux of micrometeorites which are not slowed down from their cosmic velocities because of the lack of air (data indicate that microcraters greater than 10 microns across will form at the rate of 3000/sq m/yr); (10) regolith 2 to 30 m thick which blankets the entire lunar surface (this layer is fine-grained (average grain sizes range from 40 to 268 microns), has a low density (800 to 1000 kg/cu m in the upper few mm, rising to 1500 to 1800 kg/cu m at depths of 10 to 20 cm), is porous (35 to 45 pct), cohesive (0.1 to 1.0 kN/sq m), and has a low thermal diffusivity (0.7 to 1.0 x 110-8 sq m/sec); about 29 pct of the regolith is less than 20 micron in size (this dust could pose a hazard to optical telescopes); (11) rubbly upper several hundred meters in which intact bedrock is uncommon, especially in the lunar highlands; and (12) craters with diameter-to-depth ratios of 5 if fresh and less than km across (larger and eroded craters have diameter-to-depth ratios greater than 5).

Taylor, G. Jeffrey↗
NASA NTRSDate not supplied

Column Optical Depth (COD) Derived from CALIOP Ocean Surface Returns

The Cloud Aerosol Lidar with Orthogonal Polarization (CALIOP) on board the Cloud Aerosol Lidar Infrared Pathfinder Satellite Observations (CALIPSO) satellite has been making near-global measurements of clouds and aerosols since mid-June 2006. Among the properties reported in CALIPSO data products are estimates of total column optical depth (COD) obtained by integrating the retrieved extinction coefficients of detected particulates (i.e., aerosols and clouds) from 36 km to the surface. However, due to algorithm detection limits and instrument sensitivities, particulates can go undetected when the particulate loading is especially diffuse or in regions where the signal is attenuated by over-lying layers. Because extinction is not calculated where features are not detected, these undetected particulates can introduce low biases into the reported COD. Lidar ratio assumptions used in the extinction retrievals can also introduce errors. To minimize these biases, future releases of the CALIPSO lidar data products will implement an ocean-derived column optical depth (ODCOD) retrieval. The following paper briefly describes the algorithm, the current status of the algorithm development and verification efforts, and preliminary comparisons to col-located COD estimates derived using other retrieval schemes and obtained from other sensors.

Robert A Ryan↗
NASA NTRS2017

Effect of Ram and Zenith Exposure on the Optical Properties of Polymers in Space

The temperature of spacecraft is influenced by the solar absorptance and thermal emittance of the external spacecraft materials. Optical and thermal properties can degrade over time in the harsh low Earth orbital (LEO) space environment where spacecraft external materials are exposed to various forms of radiation, thermal cycling, and atomic oxygen. Therefore, it is important to test the durability of spacecraft materials in the space environment. One objective of the Polymers and Zenith Polymers Experiments was to determine the effect of LEO space exposure on the optical properties of various spacecraft polymers. These experiments were flown as part of the Materials International Space Station Experiment 7 (MISSE 7) mission on the exterior of the International Space Station (ISS) for 1.5 years. Samples were flown in ram, wake or zenith directions, receiving varying amounts of atomic oxygen and solar radiation exposure. Total and diffuse reflectance and transmittance of flight and corresponding control samples were obtained post-flight using a Cary 5000 UV-Vis-NIR Spectrophotometer. Integrated air mass zero solar absorptance (s) of the flight and control samples were computed from the total transmittance and reflectance, and compared. The optical data are compared with similar polymers exposed to space for four years as part of MISSE 2, and with atomic oxygen erosion data, to help understand the degradation of these polymers in the space environment. Results show that prolonged space exposure increases the solar absorptance of some materials. Knowing which polymers remain stable will benefit future spacecraft design.

Yuanchun Li↗
NASA NTRS2021

A Three-Step Semi Analytical Algorithm (3SAA) for Estimating Inherent Optical Properties Over Oceanic, Coastal, and Inland Waters From Remote Sensing Reflectance

We present a three-step inverse model (3SAA) for estimating the inherent optical properties (IOPs) of surface waters from the remote sensing reflectance spectra, Rrs(). The derived IOPs include the total (a()), phytoplankton (aphy()), and colored detrital matter (acdm()), absorption coefficients, and the total (bb()) and particulate (bbp()) backscattering coefficients. The first step uses an improved neural network approach to estimate the diffuse attenuation coefficient of downwelling irradiance from Rrs. a() and bbp() are then estimated using the LS2 model (Loisel et al., 2018), which does not require spectral assumptions on IOPs and hence can assess a() and bb() at any wavelength at which Rrs() is measured. Then, an inverse optimization algorithm is combined with an optical water class (OWC) approach to assess aphy() and acdm() from anw().The proposed model is evaluated using an in situ dataset collected in open oceanic, coastal, and inland waters. Comparisons with other standard semi-analytical algorithms (QAA and GSM), as well as match-up exercises, have also been performed. The applicability of the algorithm on OLCI observations was assessed through the analysis of global IOPs spatial patterns derived from 3SAA and GSM. The good performance of 3SAA is manifested by median absolute percentage differences (MAPD) of 13%, 23%, 34% and 34% for bbp(443), anw(443), aphy(443) and acdm(443), respectively for oceanic waters. Due to the absence of spectral constraints on IOPs in the inversion of total IOPs, and the adoption of an OWC-based approach, the performance of 3SAA is only slightly degraded in bio-optical complex inland waters.

ocean color↗
NASA NTRS1987

Flow in out-of-plane double S-bends

An experimental investigation of developing flows through a combination of out-of-plane S-bend ducts was conducted to gain insight into the redirection of flow in geometries similar to those encountered in practical aircraft wing-root intake ducts. The present double S-bend was fabricated by placing previously investigated S-ducts and S-diffusers in series and with perpendicular planes of symmetry. Laser-Doppler anemometry was employed to measure the three components of mean velocity, the corresponding rms quantities, and Reynolds stresses in the rectangular cross-section ducts. Due to limited optical access, only two mean and rms velocity components were resolved in the circular cross-section ducts. The velocity measurements were complemented by wall static pressure measurements. The data indicates that the flows at the exit are complex and asymmetric. Secondary flows generated by the pressure field in the first S-duct are complemented or counteracted by the secondary flows produced by the area expansion and the curvature of the S-diffuser. The results indicate the dominance of the inlet conditions and geometry upon the development of secondary flows and demonstrate that the flows are predominantly pressure-controlled. The pressure distribution caused by the duct geometry determines the direction and magnitude of the bulk flow while the turbulence dictates the mixing characteristics and profiles in the near wall region.

Schmidt, M. C.↗
NASA NTRS2011

Numerical Simulations of Single and Multiple Scattering by Fractal Ice Clusters

We consider the scattering model in the form of a vertically and horizontally homogeneous particulate slab of an arbitrary optical thickness composed of widely separated fractal aggregates built of small spherical ice monomers. The aggregates are generated by applying three different approaches, including simulated cluster-cluster aggregation (CCA) and diffusion-limited aggregation (DLA) procedures. Having in mind radar remote-sensing applications, we report and analyze the results of computations of the backscattering circular polarization ratio obtained using efficient superposition T-matrix and vector radiative-transfer codes. The computations have been performed at a wavelength of 12.6 cm for fractal aggregates with the following characteristics: monomer refractive index m=1.78+i0.003, monomer radius r=1 cm, monomer packing density p=0.2, overall aggregate radii R in the range 4<=R<=10 cm and fractal dimensions D(sub f) 2.5 and 3. We show that for aggregates generated with simulated CCA and DLA procedures, the respective values of the backscattering circular polarization ratio differ weakly for D(sub f) 2.5, but the differences can increase somewhat for D(sub f)3, especially in case of an optically semi-infinite medium. For aggregates with a spheroidal overall shape, the dependence of the circular polarization ratio on the cluster morphology can be quite significant and increases with increasing the aspect ratio of the circumscribing spheroid.

Dlugach, Janna M.↗
NASA NTRS1973

Mariner 9 ultraviolet spectrometer experiment - 1971 Mars' dust storm.

The brightness of a region on the south polar cap centered at approximately -87 deg S, 10 deg W was observed. Measurements taken at various incidence and emission angles show that the brightness increased with decreasing air mass. The observed intensity consists primarily of a component reflected from the cap and twice attenuated by the atmosphere and a component diffusely reflected from the atmosphere. The dust cloud over the polar cap was moderately thick between Nov. 26 and Dec. 2, 1971. At this time the optical thickness was near unity, and it decreased approximately linearly with time, reaching a value close to that of a Rayleigh atmosphere by mid-February. The optical thickness showed little dependence on the wavelength during the early orbital observations.

Pang, K.↗
NASA NTRS1983

Redshift modifications to HEAO A-1 cluster X-ray luminosities

New redshift measurements for the 24 Abell galactic clusters are presented. The optical observations are described and applied to the cluster X-ray luminosity function, and the results are used to delimit the cluster contribution to the diffuse X-ray background (DXRB). The evolution of the X-ray luminosity function is then investigated. It is found that while simple two-parameter analytic forms do not fit this function very well, three-parameter forms such as the exponential times power law do fit it very well. Future redshift observations will probably not change the volume emissivity significantly, but they may in a statistically significant way affect the parameters of analytic fits which define the shape of the luminosity function. The contribution of rich clusters to the DXRB in the 2-6 keV range is 5.2 percent. Future redshift observations will modify this result by no more than a factor of about 1.1.

Cruddace, R. G.↗