Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESISTANCE HEATING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Heat sterilizable impact resistant cell development

Developments in the design and fabrication of 25 AH, 5AH, 70 AH, and 25 AH high impact cells and batteries are reported along with the development of high cycle life, low impact cells. Discussions of the performance and failure modes are included.

Jordan, A. W.↗
DOE OSTI2021

Burst resistant thin wall heat sink

An method for forming a cooling apparatus for cooling an electronic component. The apparatus has a planar top member of a thermal energy conductive material and a parallel planar bottom member of the material, the planar bottom member including a surface having regions configured for heat exchange contact with the electronic component. The planar top member has a plurality of stamped indent formations at a plurality of locations, each indent formation providing a contact surface such that the planar top member is affixed to the bottom member by braze or solder at each contact surface. Alternatively, the planar bottom member also has a plurality of stamped indent formations in alignment with indent formations of the top member. The planar top member is affixed to the bottom member by brazing or soldering each respective contact surface of an indent formation of the planar top member to an opposing contact surface of a corresponding indent formation of the parallel planar bottom member.

Coteus, Paul W.↗
NASA NTRS1980

Effect of mechanical surface and heat treatments on erosion resistance

The effects of mechanical surface treatments as well as heat treatments on the erosion resistance of 6061 aluminum alloy and 1045 steel were studied. Mechanical surface treatments were found to have little or no effect on the erosion resistance. This is due to the formation by particle impact of a work hardened surface layer regardless of the initial surface condition. The erosion resistance of Al single crystals is found to be independent of orientation. This is due to destruction of the surface microstructure and formation of a polycrystalline surface layer by the impact of erodant particles as observed by X-ray diffraction. While upon solution treatment of annealed 6061 aluminum the increase in hardness is accompanied by an increase in erosion resistance, precipitation treatment which causes a further increase in hardness results in slightly lower erosion resistance. Using two types of erodant particles, glass beads and crushed glass, the erosion rate is found to be strongly dependent on erodant particle shape, being an order of magnitude higher for erosion with crushed glass as compared to glass beads. While for erosion with glass beads heat treatment of 1045 steel had a profound effect on its erosion resistance, little or no such effect was observed for erosion with crushed glass.

Salik, J.↗
NASA NTRS1978

A siphon method of determining resistivities of thin heat-pipe wicks

A simple siphon method is described for determining the resistivities of thin heat pipe wicks as a function of the pressure difference between the liquid in the wick and the vapor above it. The method was applied to wicks of one layer and two layers of 100 mesh (40 per centimeter) stainless steel screens diffusion bonded to stainless steel substrates. Some possible improvements in the method are suggested.

Katzoff, S.↗
NASA NTRS1991

Measurements of the effects of thermal contact resistance on steady state heat transfer in phosphoric-acid fuel cell stack

The influence of the thermal contact resistance on the heat transfer between the electrode plates, and the cooling system plate in a phosphoric-acid fuel-cell stack was experimentally investigated. The investigation was conducted using a set-up that simulates the operating conditions prevailing in a phosphoric acid fuel-cell stack. The fuel-cell cooling system utilized three types of coolants, water, engine oil, and air, to remove excess heat generated in the cell electrode and to maintain a reasonably uniform temperature distribution in the electrode plate. The thermal contact resistance was measured as a function of pressure at the interface between the electrode plate and the cooling system plate. The interface pressure range was from 0 kPa to 3448 kPa, while the Reynolds number for the cooling limits varied from 15 to 79 for oil, 1165 to 6165 for water, and 700 to 6864 for air. Results showed that increasing the interface pressure resulted in a higher heat transfer coefficient.

Abdul-Aziz, Ali↗
NASA NTRS1981

Effect of mechanical surface and heat treatments on erosion resistance

The effect of erosion by glass beads and crushed glass and by heat treatments on the erosional resistance of 6061 aluminum alloy and 1045 steel were studied. The aluminum alloy's erosion resistance was found to be insensitive to mechanical surface treatment applied before testing, and was determined to depend on the properties of the work-hardened surface layer; this was also demonstrated for aluminum alloy single crystals. The aluminum alloy heat treatments included annealing, solution, and precipitation. Solution was found to increase erosion resistance but precipitation had the opposite effect. Hardness showed no correlation with erosion resistance for either aluminum alloy steel. The steel tests showed that crushed glass provides an order of magnitude more erosion than glass beads.

Salik, J.↗
NASA NTRS1994

Sensible heat flux - Radiometric surface temperature relationship for eight semiarid areas

Measurements of sensible heat flux, radiometric surface temperature, air temperature, and wind speed made at eight semiarid rangeland sites were used to investigate the sensible heat flux-aerodynamic resistance relationship. The individual sites covered a wide range of vegetation (0.1-4 m tall) and cover (3%-95% bare soil) conditions. Mean values of k/B, a quantity related to the resistance of heat versus momentum transfer at the surface, for the individual sites varied between 3.5 and 12.5. A preliminary test of the utility of an excess resistance based on the mean value of k/B showed that the difference between the mean estimated and measured sensible heat fluxes varied +/- 60 W/sq m for the eight semiarid sites. For the eight sites the values of k/B were plotted against the roughness Reynolds number. The plot showed considerable scatter with values ranging between and beyond the theoretical curves for bluff rough and permeable rough surfaces.

Stewart, J. B.↗