Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Low temperature synthesis and sintering of d-UO2 nanoparticles.

We report on the novel room temperature method of synthesizing advanced nuclear fuels; a method that virtually eliminates any volatility of components. This process uses radiolysis to form stable nanoparticle (NP) nuclear transuranic (TRU) fuel surrogates and in-situ heated stage TEM to sinter the NPs. The radiolysis is performed at Sandia's Gamma Irradiation Facility (GIF) 60Co source (3 x 10{sup 6} rad/hr). Using this method, sufficient quantities of fuels for research purposes can be produced for accelerated advanced nuclear fuel development. We are focused on both metallic and oxide alloy nanoparticles of varying compositions, in particular d-U, d-U/La alloys and d-UO2 NPs. We present detailed descriptions of the synthesis procedures, the characterization of the NPs, the sintering of the NPs, and their stability with temperature. We have employed UV-vis, HRTEM, HAADF-STEM imaging, single particle EDX and EFTEM mapping characterization techniques to confirm the composition and alloying of these NPs.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Polycyclic aromatic hydrocarbon emission profiles and removal efficiency by electrostatic precipitator and wetfine scrubber in an iron ore sintering plant

A monitoring campaign of polychlorinated dibenzo-p-dioxins and dibenzofurans, polyaromatic hydrocarbons (PAHs), and polychlorinated biphenyl was carried out in an Italian iron ore sintering plant by sampling the combustion gases at the electrostatic precipitator (ESP) outlet, at the Wetfine scrubber (WS) outlet, and by collecting the ESP dust. Few data are available on these micropollutants produced in iron ore sintering plants, particularly from Italian plants. This study investigates the PAH emission profiles and the removal efficiency of ESPs and WS. PAHs were determined at the stack, ESP outlet flue gases, and in ESP dust to characterize the emission profiles and the performance of the ESP and the WS for reducing PAH emission. The 11 PAHs monitored are listed in the Italian legislative decree 152/2006. The mean total PAH sum concentration in the stack flue gases is 3.96 {mu}g/N m{sup 3}, in ESP outlet flue gases is 9.73 {mu}g/N m{sup 3}, and in ESP dust is 0.53 {mu}g/g. Regarding the emission profiles, the most abundant compound is benzo(b)fluoranthene, which has a relative low BaP toxic equivalency factors (TEF) value, followed by dibenzo(a,l)pyrene, which has a very high BaP(TEF) value. The emission profiles in ESP dust and in the flue gases after the ESP show some changes, whereas the fingerprint in ESP and stack flue gases is very similar. The removal efficiency of the ESP and of WS on the total PAH concentration is 5.2 and 59.5%, respectively. 2 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Optimization of sintered AgI-Mordenite composites for {sup 129}I storage

The thermal processing of a proposed durable waste form for {sup 129}I was investigated. The waste form is a composite with a matrix of low-temperature sintering glass that encapsulates particles of AgI-mordenite. Ag-mordenite, an ion-exchanged zeolite, is being considered as a capture medium for gaseous {sup 129}I{sub 2} as part of a spent nuclear fuel reprocessing scheme under development by the US Department of Energy/Nuclear Energy (NE). The thermal processing of the waste form is necessary to increase the density of the glass matrix by viscous sintering so that the final waste form does not have any open porosity. Other processes that can also occur during the thermal treatment include desorption of chemisorbed I{sub 2}, volatilization of AgI and crystallization of the glass matrix. We have optimized the thermal processing to achieve the desired high density with higher AgI-mordenite loading levels and with minimal loss of iodine. Using these conditions, 625 C. degrees for 20 minutes, the matrix crystallizes to form a eulytite phase. Results of durability tests indicate that the matrix crystallization does not significantly decrease the durability in aqueous environments. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ultra‐Uniform Nanocrystalline Materials via Two‐Step Sintering

Abstract Nanocrystalline materials with superior properties are of great interest. Much is discussed about obtaining nanograins, but little is known about maintaining grain‐size uniformity that is critical for reliability. An especially intriguing question is whether it is possible to achieve a size distribution narrower than what Hillert theoretically predicted for normal grain growth, a possibility suggested—for growth with a higher growth exponent—by the generalized mean‐field theory of Lifshitz, Slyozov, Wagner (LSW), and Hillert but never realized in practice. Following a rationally designed two‐step sintering route, it has been made possible in bulk materials by taking advantage of the large growth exponent in the intermediate sintering stage to form a uniform microstructure despite residual porosity, and freezing the grain growth thereafter while continuing densification to reach full density. The bulk dense Al 2 O 3 ceramic thus obtained has an average grain size of 34 nm and a size distribution much narrower than Hillert's prediction. Bulk Al 2 O 3 with a grain‐size distribution narrower than the particle‐size distribution of starting powders is also demonstrated, as are highly uniform bulk engineering metals (refractory Mo and W‐Re alloy) and complex functional ceramics (BaTiO 3 ‐based alloys with superior dielectric strength and energy capacity).

Dong, Yanhao↗

Laser‐Sintered Silver Metallization for Silicon Heterojunction Photovoltaic Cells

Herein, a novel metallization technique is reported for crystalline silicon heterojunction (SHJ) solar cells in which silver (Ag) fingers are printed on the SHJ substrates by dispensing Ag nanoparticle‐based inks through a needle and then sintered with a continuous‐wave carbon dioxide (CO 2 ) laser. The impact of the Ag ink viscosity on the line quality and the line resistance is investigated on three Ag inks with different viscosities. Increasing ink viscosity yields higher Ag contact heights, larger aspect ratios, and lower line resistance values. The Ag line height increases from less than a micrometer to ≈18.62 ± 3.48 μm with the increasing viscosity. Photoluminescence imaging shows that the low‐resistance Ag metal contacts obtained do not result in any passivation damage of the SHJ substrate. This is because the wavelength of light emitted from the CO 2 laser (i.e., 10.6 μm) leads to optical absorption in the Ag, but this light is effectively transparent to the transparent conductive oxide film, amorphous silicon films, and crystalline silicon substrate. Bulk resistivity values as low as 6.5 μΩ cm are obtained for the laser‐sintered Ag contact and printed using the Ag ink with the highest viscosity in this work.

Mousumi, Jannatul Ferdous↗

Effects of Sintering Temperature on Structural, Morphological and Magnetic Properties of Strontium Ferrite Nanoparticles

In the present investigation, structural, morphological and magnetic properties of SrFe{sub 2}O{sub 4} ferrite nanoparticles prepared by a sol–gel method were studied. The techniques used in this investigation were thermogravimetric analysis/differential thermal analysis (TGA/DTA), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), field emission scanning electron microscopy (FESEM), Fourier transform infrared spectrometry (FT-IR), vibrating sample magnetometry (VSM) and Curie temperature analysis. The average crystallite sizes of the SrFe{sub 2}O{sub 4} were calculated using the Scherrer formula and found in the range of 11–22 nm, and this can be attributed to the grain growth of the particles. The lattice parameter of SrFe{sub 2}O{sub 4} nanoparticles decreased from 6.64 to 6.51 nm as the sintering temperature was raised from 600 to 900 °C. FT-IR analysis confirmed that bands in the range 430–590 cm{sup − 1} are due to the stretching vibration of oxygen atom and metal ions (M–O) that is Fe–O confirming the formation of spinel ferrite. Surface morphology of the samples has been studied using FESEM. The elemental composition along with their relative ratios was given by EDX and was found to be in agreement with their initial calculated values. The saturation magnetization, magnetic coercivity and remanence increase with an increasing sintering temperature from 600 to 900 °C. The present study reports the Curie temperature with an amount of 551 °C of the synthesized strontium nanoferrites using the Faraday technique.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Structural, Infrared, Magnetic, and Electrical Properties of Ni{sub 0.6}Cd{sub 0.2}Cu{sub 0.2}Fe{sub 2}O{sub 4} Ferrites Synthesized Using Sol-Gel Method Under Different Sintering Temperatures

Ni{sub 0.6}Cd{sub 0.2}Cu{sub 0.2}Fe{sub 2}O{sub 4} ferrites were synthesized using sol-gel method under different sintering temperatures. XRD patterns with the Rietveld refinement indicate that samples crystallize in the cubic spinel structure. The increase of sintering temperature leads successively to the increase of lattice constant, average crystallite size, intensities of absorption bands, magnetization, and electrical conductivity of the prepared ferrites. Dielectric constants decrease with frequency and their behaviors have been investigated using the interfacial polarization theory predicted by Maxwell. The modulus analysis shows the presence of electrical relaxation phenomenon and non-Debye nature for the samples. An appropriate electrical equivalent circuit was used to analyze the Nyquist plots, and the results show that the conduction mechanism of the synthesized ferrites is mainly due to the grain boundary contribution.

36 MATERIALS SCIENCE↗

Mechanical and Tribological Behavior of ZrB{sub 2}-TiB{sub 2} System Prepared by Mechanical Activation Spark Plasma Sintering Technique

ZrB{sub 2}-TiB{sub 2} system among varying amount of TiB{sub 2} loading (5, 10, 15, 20 and 30 wt.%) was prepared by mechanical activation spark plasma sintering at 2100 °C for 15-min dwell time under 50 MPa uniaxial pressure in argon atmosphere. The effect of the TiB{sub 2} loading on properties like physical, mechanical and tribological of the prepared samples was studied and evaluated with monolithic ZrB{sub 2} ceramic. Finally, almost fully dense samples (> 96% of theoretical density) were fabricated. Microstructural observation and XRD phase analysis of sintered compact revealed that TiB{sub 2} completely went into the ZrB{sub 2} structure by formation of solid solution with ZrB{sub 2} phase. ZrB{sub 2}-TiB{sub 2} (30 wt.%) showed the highest Vickers micro-hardness (H{sub V}) of 20.64 GPa at 10 N load. On addition of TiB{sub 2}, the fracture toughness of the ZrB{sub 2}-TiB{sub 2} improved up to 4.69 ± 0.43 MPa m{sup 1/2} over monolithic ZrB{sub 2} at 10 N load. At 10 N load, the scratch resistance coefficient, wear rate and wear resistance coefficient of ZrB{sub 2}-TiB{sub 2} (30 wt.%) reached a lowest value of 0.32, 0.35 mm{sup 3}/N m and 0.008, respectively, at 10 N load than other ZrB{sub 2} compositions.

36 MATERIALS SCIENCE↗

Effect of MWCNT Content on the Structure and Properties of Spark Plasma-Sintered Iron-MWCNT Composites Synthesized by High-Energy Ball Milling

The effect of multiwall carbon nanotube (MWCNT) content on the physical and mechanical properties of Fe-MWCNT composites has been studied. High-energy ball milling (HEBM) is employed to produce the composite powder; following this, spark plasma sintering (SPS) process has been adopted for powder consolidation. The composite powder and the sintered products were subjected to structural characterization by XRD. Microstructural studies were carried out by optical, field-emission scanning and high-resolution transmission electron microscopy. While Fourier transform infrared spectroscopic study of composites was done to understand the bonding characteristics, Raman spectroscopy was employed to assess the structural damage of MWCNT after HEBM. The effects of processing on the behavior of C-C, C-O and Fe-O bonds are studied by x-ray photoelectron spectroscopy. Microhardness and compressive strength of composites are also determined. Finally, magnetic and electrical properties of the composites were characterized. It was observed that optimized ball milling conditions help to preserve the structural identity of MWCNT. Consolidation by SPS insured good interfacial bonding. The microhardness and compression strength are significantly improved in MWCNT-reinforced iron matrix composite. MWCNT has appreciably improved the electrical conductivity of the composites. Tethering of MWCNT by iron oxide has led to appreciable improvement in saturation magnetization till 3 wt.% MWCNT.

36 MATERIALS SCIENCE↗

Compression Molding and Novel Sintering Treatments for Alnico Type-8 Permanent Magnets in Near-Final Shape with Preferred Orientation

We present economic uncertainty in the rare earth (RE) permanent magnet marketplace, as well as in an expanding electric drive vehicle market that favors permanent magnet alternating current synchronous drive motors, motivated renewed research in RE-free permanent magnets like “alnico,” an Al-Ni-Co-Fe alloy. Thus, high-pressure, gas-atomized isotropic type-8H pre-alloyed alnico powder was compression molded with a clean burn-out binder to near-final shape and sintered to density >99% of cast alnico 8 (full density of 7.3 g/cm 3 ). To produce aligned sintered alnico magnets for improved energy product and magnetic remanence, uniaxial stress was attempted to promote controlled grain growth, avoiding directional solidification that provides alignment in alnico 9. Lastly, successful development of solid-state powder processing may enable anisotropically aligned alnico magnets with enhanced energy density to be mass-produced.

36 MATERIALS SCIENCE↗

Evaluation of sintered bauxite proppant for binary enhanced geothermal systems

Abstract Solid granular proppant particles are widely used in oil and gas development to sustain permeability through fractures after hydraulic stimulation. Similar proppants are of interest for geothermal applications where the goal of sustaining permeability is the same, but the harsh geothermal environment risks rapid proppant degradation that will reduce fracture permeability. Here, we present proppant conductivity experiments using saw cut granite, tensile fractured granite, and aluminum control specimens packed with sintered bauxite ceramic proppants at concentrations of 0.0, 0.1, and 1.0 kg/m 2 . Simulated geothermal conditions included temperatures up to 130 °C and normal closure stresses up to 60 MPa. Compared to unpropped specimens, peak fracture conductivity enhancement was up to 6 orders of magnitude. At simulated geothermal conditions, proppants were able to sustain fracture conductivity over 60 h, but chemical dissolution and decreasing permeability over time were evident. Irreversible conductivity reductions with crushing and embedment of proppants during loading stages were also observed. Overall, sintered bauxite proppant remains a promising option for low-temperature binary-cycle enhanced geothermal systems.

58 GEOSCIENCES↗

The Functional Resonance Analysis Method for a systemic risk based environmental auditing in a sinter plant: A semi-quantitative approach

Environmental auditing is a main issue for any production plant and assessing environmental performance is crucial to identify risks factors. The complexity of current plants arises from interactions among technological, human and organizational system components, which are often transient and not easily detectable. The auditing thus requires a systemic perspective, rather than focusing on individual behaviors, as emerged in recent research in the safety domain for socio-technical systems. We explore the significance of modeling the interactions of system components in everyday work, by the application of a recent systemic method, i.e. the Functional Resonance Analysis Method (FRAM), in order to define dynamically the system structure. We present also an innovative evolution of traditional FRAM following a semi-quantitative approach based on Monte Carlo simulation. This paper represents the first contribution related to the application of FRAM in the environmental context, moreover considering a consistent evolution based on Monte Carlo simulation. The case study of an environmental risk auditing in a sinter plant validates the research, showing the benefits in terms of identifying potential critical activities, related mitigating actions and comprehensive environmental monitoring indicators. - Highlights: • We discuss the relevance of a systemic risk based environmental audit. • We present FRAM to represent functional interactions of the system. • We develop a semi-quantitative FRAM framework to assess environmental risks. • We apply the semi-quantitative FRAM framework to build a model for a sinter plant.

54 ENVIRONMENTAL SCIENCES↗

Thermophysical properties of sintered aluminum-silicon

The effect of silicon addition to aluminum on the thermophysical properties of Al was experimentally investigated. Thermal diffusivity, heat capacity, density, and thermal expansion of sintered Al-Si samples with Si content ranging 0-8 wt% were measured. For U-Mo/Al dispersion fuel for research reactors, an addition of Si (up to 8 wt% Si) to the Al matrix has been adopted as a method to reduce the formation of interaction layer between the U-Mo and the Al. In this study, the Si-added Al matrix was simulated by using a powder metallurgical method, in which an Al powder and a Si powder were mixed and sintered. All measured properties decreased with the addition of Si. The effect was most pronounced in thermal diffusivity while the decreases in heat capacity and density were relatively insignificant. The measured thermal conductivity from the present study was higher than those measured data for alloy samples available in the literature to the differences in the fabrication method. All measured data including this study, however, were lower than the prediction by the Bruggeman model. It is because the model assumes an ideal heat-transfer conditions such as spherical particles, homogeneous particle distribution, perfect bonding between Al and Si. (C) 2018 Elsevier B.V. All rights reserved.

Cho, Tae Won↗

Elastic moduli of high-density, sintered monoliths of yttrium dihydride

Yttrium dihydride has been considered as potential nuclear reactor moderator for micro-reactors operating in the thermal energy spectrum due to their ability to retain hydrogen to high temperatures while having a relatively low impact on neutron economy. Despite these advantages, it is difficult to prepare yttrium dihydride in high-density, near net-shape monoliths for moderator applications due to volume expansion upon hydriding and the pyrophoric nature of the material. In this work, high-density monoliths of yttrium dihydride were prepared by direct hydriding and using powder metallurgical methods. Resonant ultrasound spectroscopy was used to measure the elastic moduli of the sintered monoliths, while nanoindentation was used to determine the Young’s modulus and hardness of the directly-hydrided yttrium and the sintered monoliths. Single crystal elastic constants and related properties of yttrium dihydride were also determined using density functional theory (DFT) for comparison. We report mechanical properties of materials produced by both methods were observed to be consistent with the values from literature for yttrium dihydride. Due to the novelty of producing yttrium dihydride by powder metallurgy, this result indicated that the monoliths produced by powder metallurgy were of high quality. To that end, powder metallurgy is believed to be a viable method for large-scale production of yttrium dihydride monoliths for nuclear reactor moderator applications.

36 MATERIALS SCIENCE↗

Thermophysical properties of high-density, sintered monoliths of yttrium dihydride in the range 373–773 K

Yttrium dihydride is a promising nuclear reactor moderator for high-temperature, thermal micro-reactors due to its ability to retain hydrogen to high temperatures while having a relatively low impact on neutron economy. However, it is difficult to fabricate yttrium dihydride in high-density, near net-shape monoliths for moderator applications due to challenges associated with the hydrogen absorption process. Here, high-density monoliths of yttrium dihydride were prepared by powder metallurgical methods. The lattice strain and thermal expansion coefficient were measured using neutron diffraction of powders of directly-hydrided yttrium, while the molar heat capacity and thermal diffusivity of sintered yttrium dihydride were measured using differential scanning calorimetry (DSC) and laser flash analysis (LFA), respectively. The molar heat capacity of yttrium dihydride was also calculated using density functional theory (DFT) for comparison. These parameters were used to then calculate the thermal conductivity and resistivity of yttrium dihydride as a function of temperature. The thermophysical properties of materials produced by both methods were observed to be consistent with the values from literature for yttrium dihydride. Due to the novelty of producing yttrium dihydride by powder metallurgical methods, this result indicated that the sintered monoliths were of high quality and that powder metallurgy is a viable method for large-scale production of yttrium dihydride monoliths for nuclear reactor moderator applications.

36 MATERIALS SCIENCE↗

Synthesis and flash sintering of (Hf 1-x Zr x )B 2 solid solution powders

(Hf 1-x Zr x )B 2 solid solution powders were synthesized by two methods. First, solution-based processing of HfCl 4 , ZrCl 4 , sucrose, and H 3 BO 3 was conducted followed by heat treatment in Argon to carry out the carbothermal reduction (CTR) reaction to form the diboride powders. Alternatively, in the so-called borohydride reduction (BHR) method, HfCl 4 , ZrCl 4 and NaBH 4 were mixed in an Argon glove box followed by heat treatment in Argon at 700-1500°C. The synthesized powders were characterized by XRD, SEM, TEM, EDS, and TGA, and the influence of different parameters such as starting composition, heat treatment temperature and time on products characteristics were revealed. Both CTR and BHR solid solution powders were then consolidated within ~5 min in a homemade flash sintering (FS) setup. Here, the composition, microstructure, hardness, and thermal-oxidation properties of flash sintered ceramics were characterized, and the implication of this study and directions for future research were discussed.

36 MATERIALS SCIENCE↗

Effects of the addition of boron nitride nanoplate on the fracture toughness, flexural strength, and Weibull Distribution of hydroxyapatite composites prepared by spark plasma sintering

Hydroxyapatite (HA) has inherently low fracture toughness and low flexural strength, thus limiting it from wide scale application as an implant material in the biomedical field. To increase the fracture toughness and flexural strength, HA composites were fabricated by adding boron nitride nanoplatelets (BNNP) as reinforcement. Spark plasma sintering was utilized to achieve fine grain structure. The addition of BNNP facilitated grain size refinement. The BNNP reinforced HA composites exhibited increased fracture toughness (2.3 MPa m 1/2 ) and flexural strength (79.79 MPa) of HA over previous published values (1.0 MPa m 1/2 ). Despite that the Weibull Distribution indicated a sacrifice in mechanical reliability, all the composites fabricated in this study showed a low probability of failure and a factor of safety (~ 5.6) that is consistent with that of human bones (~ 6). In addition, the current study provides an approach to statistically design sintering parameters and mechanical loading for fabrication of ceramics.

36 MATERIALS SCIENCE↗

Selective laser sintering of MA956 oxide dispersion strengthened steel

Oxide Dispersion Strengthened (ODS) steels’ qualities of radiation damage resistance and high strength at high temperature make them promising nuclear structural materials. However, the dispersed yttria that gives ODS steel its beneficial qualities are generally compromised during joining processes, making fabrication difficult and expensive. The selective laser sintering process offers a potential path through this barrier by which net-shape parts can feasibly be built via additive manufacturing without fully melting the structure. By rastering a 400 W laser over a MA956 ODS steel powder bed, here we additively built parts with varying build conditions. Although density was achieved to within 97% of the wrought MA956, ultimate tensile strengths achieved only 65% of the wrought strength. Spectroscopy analysis points to the agglomeration of the yttria nano-particles as a possible explanation for the loss in strength. Further study might benefit from exploration of other parameters such as thinner powder build layers which would require less energy input to achieve sintering while minimizing time above the melting temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗