Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS RELAXATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Effects of pre-annealing on the uni- and bi-axial stretching behavior of poly(ethylene naphthalate) films

Effect of pre-annealing on stress and birefringence behavior of poly(ethylene naphthalate) (PEN) films during stretching and relaxation processes was investigated. Amorphous and non-oriented PEN films were pre-annealed under the conditions of different temperatures and periods. The pre-annealed films were stretched uniaxially or equi-biaxially and then relaxed at fixed length. It was found that pre-annealing did not cause any notable change for the initial behavior of refractive indices variation, whereas the behaviors after necking were significantly affected. Through the comparison between in-plane and out-of-plane birefringence and the analysis of wide-angle x-ray diffraction patterns of drawn films of both stretching modes, it was confirmed that the orientation of naphthalene ring in the film plane was enhanced by pre-annealing.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of Processing Parameters on Internal Stress of BN Films Prepared by Ion Mixing and Vapor Deposition

Boron nitride (BN) films have been attractive due to their excellent properties such as high hardness, thermal conductivity and chemical stability. In this study, BN films were prepared by depositing B vapor under simultaneous irradiation of N ions, that is ion mixing and vapor deposition (IVD) technique. The effects of processing parameters such as, acceleration voltage of N ions, transport ratio B/N and substrate temperature, on the internal stress of BN films were investigated. As a result, compressive internal stress increases at low acceleration voltage and high transport ratio B/N, which corresponded to the condition for formation of cBN phase. The hardness also becomes high at this condition and there is a strong correlation between internal stress and hardness of BN film. In addition to that, relaxation of internal stress by inserting inner layer between substrate and cBN layer has been carried out. It is confirmed that internal stress can be decreased by inner layer. Especially, relaxation of internal stress without degradation of high hardness can be achieved when the crystal structure of inner layer is hBN.

36 MATERIALS SCIENCE↗

The contour method cutting assumption: error minimization and correction

The recently developed contour method can measure 2-D, cross-sectional residual-stress map. A part is cut in two using a precise and low-stress cutting technique such as electric discharge machining. The contours of the new surfaces created by the cut, which will not be flat if residual stresses are relaxed by the cutting, are then measured and used to calculate the original residual stresses. The precise nature of the assumption about the cut is presented theoretically and is evaluated experimentally. Simply assuming a flat cut is overly restrictive and misleading. The critical assumption is that the width of the cut, when measured in the original, undeformed configuration of the body is constant. Stresses at the cut tip during cutting cause the material to deform, which causes errors. The effect of such cutting errors on the measured stresses is presented. The important parameters are quantified. Experimental procedures for minimizing these errors are presented. An iterative finite element procedure to correct for the errors is also presented. The correction procedure is demonstrated on experimental data from a steel beam that was plastically bent to put in a known profile of residual stresses.

36 MATERIALS SCIENCE↗

Growth of multilayers of Bi{sub 2}Se{sub 3}/ZnSe: Heteroepitaxial interface formation and strain

Multilayers of Bi{sub 2}Se{sub 3}/ZnSe with the periodicity of a few nanometers were grown by molecular-beam epitaxy on Si(111). While epitaxial growth of Bi{sub 2}Se{sub 3} on ZnSe proceeded by two-dimensional nucleation, ZnSe growth on Bi{sub 2}Se{sub 3} showed the three-dimensional growth front. Therefore, the two complementary interfaces of Bi{sub 2}Se{sub 3}/ZnSe were asymmetric in morphological properties. Strain-relaxation rates were found to differ between epitaxial ZnSe and Bi{sub 2}Se{sub 3}, which could be attributed to the specific growth modes and the properties of Bi{sub 2}Se{sub 3} and ZnSe surfaces.

36 MATERIALS SCIENCE↗

A biharmonic relaxation method for calculating thermal stress in cooled irregular cylinders

A numerical method was developed for calculating thermal stresses in irregular cylinders cooled by one or more internal passages. The use of relaxation methods and elementary methods of finite differences was found to give approximations to the correct values when compared with previously known solutions for concentric circular cylinders possessing symmetrical and asymmetrical temperature distributions.

Holms, Arthur G↗

Acute dyskerin depletion triggers cellular senescence and renders osteosarcoma cells resistant to genotoxic stress-induced apoptosis

Highlights: • Dyskerin depletion triggers cellular senescence in U2OS osteosarcoma cells. • Dyskerin-depleted cells are resistant to apoptosis induced by genotoxic stress. • Chromatin relaxation sensitizes dyskerin-depleted cells to apoptosis. - Abstract: Dyskerin is a conserved, nucleolar RNA-binding protein implicated in an increasing array of fundamental cellular processes. Germline mutation in the dyskerin gene (DKC1) is the cause of X-linked dyskeratosis congenita (DC). Conversely, wild-type dyskerin is overexpressed in sporadic cancers, and high-levels may be associated with poor prognosis. It was previously reported that acute loss of dyskerin function via siRNA-mediated depletion slowed the proliferation of transformed cell lines. However, the mechanisms remained unclear. Using human U2OS osteosarcoma cells, we show that siRNA-mediated dyskerin depletion induced cellular senescence as evidenced by proliferative arrest, senescence-associated heterochromatinization and a senescence-associated molecular profile. Senescence can render cells resistant to apoptosis. Conversely, chromatin relaxation can reverse the repressive effects of senescence-associated heterochromatinization on apoptosis. To this end, genotoxic stress-induced apoptosis was suppressed in dyskerin-depleted cells. In contrast, agents that induce chromatin relaxation, including histone deacetylase inhibitors and the DNA intercalator chloroquine, sensitized dyskerin-depleted cells to apoptosis. Dyskerin is a core component of the telomerase complex and plays an important role in telomere homeostasis. Defective telomere maintenance resulting in premature senescence is thought to primarily underlie the pathogenesis of X-linked DC. Since U2OS cells are telomerase-negative, this leads us to conclude that loss of dyskerin function can also induce cellular senescence via mechanisms independent of telomere shortening.

60 APPLIED LIFE SCIENCES↗

Micro-slotting Residual Stress Measurement Technique for Understanding Fatigue Performance of Open-Hole Ti-6Al-4V Samples

Micro-slotting, a microscale relaxation residual stress measurement technique, has been shown in recent years to be a reliable method for measuring local residual stresses in metallic materials. This study demonstrates the unique application of the micro-slotting residual stress measurement technique for measuring near-edge tangential residual stresses around cold-expanded holes in Ti-6Al-4V plates. Knowledge of the near-edge elastic strains induced by the hole processing, in combination with plastic strain information obtained using electron backscatter diffraction, allowed for interpretation of fatigue life differences and crack growth behavior between the as-drilled and cold-expanded conditions. The similar crack initiation lives of the as-drilled and cold-expanded open-hole coupons were attributed to the similar elastic and plastic strains present at the hole edges. The subsequent crack growth resistance observed for the cold-expanded holes was a result of the large compressive residual stress region induced by cold expansion.

36 MATERIALS SCIENCE↗

Fatigue Characterization of Alloy 10: a 1300F Disk Alloy for Small Gas Turbine Engines

A detailed fatigue characterization of Alloy 10, a high strength nickel-based disk alloy, was conducted on test coupons machined from a 'pancake' forging. Smooth bar, strain controlled fatigue testing at various R-ratios was run at representative bore, 750 F, and rim, 1300 F, temperatures. This was followed by notch fatigue testing (Kt=2) run under load control. Analysis of the fatigue data using a Smith-Watson-Topper approach and finite element analysis of the notch root was employed to understand material behavior in these tests. Smooth bar fatigue data showed a significant R-ratio dependence at either test temperature which could be accounted for using a Smith-Watson-Topper parameter (SWT). In general, fatigue life was longer at 750 F than 1300 F for a given SWT. For notch fatigue tests, life was longer at 750 F than 1300 F but only at higher stresses. This was attributed to differences in alloy strength. At lower stresses, finite element analysis suggested that convergence of fatigue life at both temperatures resulted from relaxation of stresses at the notch root in the 1300 F tests.

Gayda, John↗

Strain relaxation effect by nanotexturing InGaN/GaN multiple quantum well

The relaxation of lattice-mismatched strain by deep postetching was systematically investigated for InGaN/GaN multiple quantum wells (MQWs). A planar heterojunction wafer, which included an In{sub 0.21}Ga{sub 0.79}N (3.2 nm)/GaN (14.8 nm) MQW, was etched by inductively coupled plasma dry etching, to fabricate high-density nanopillar, nanostripe, and nanohole arrays. The etching depth was 570 nm for all nanostructures. The diameter of the nanopillars was varied from 50 to 300 nm, then the mesa stripe width of the nanostripes and the diameter of the nanoholes were varied from 100 nm to 440 nm and 50 nm to 310 nm, respectively. The effect of strain relaxation on various optical properties was investigated. For example, in an array of nanopillars with diameter 130 nm and interval 250 nm, a large blueshift in the photoluminescence (PL) emission peak from 510 nm (as-grown) to 459 nm occurred at room temperature (RT). PL internal quantum efficiency (defined by the ratio of PL integral intensity at 300 K to that at 4.2 K) was enhanced from 34% (as-grown) to 60%, and the PL decay time at 4.2 K was reduced from 22 ns (as-grown) to 4.2 ns. These results clearly indicate the reduction of lattice-mismatched strain by postetching, which enhanced strain reduction with decreasing nanopillar diameter down to a diameter of 130 nm, where the strain reduction became saturated. The dependence of RT-PL decay time on nanopillar diameter was measured, and the surface nonradiative recombination velocity was estimated to be 5.8x10{sup 2} cm/s. This relatively slow rate indicates a little etching damage.

36 MATERIALS SCIENCE↗

Molecular beam epitaxy growth and optical properties of AlN nanowires

Growth of catalyst-free AlN nanowires has been achieved by plasma-assisted molecular beam epitaxy on SiO{sub 2}/Si (100), by taking advantage of Volmer-Weber growth mode of AlN on amorphous SiO{sub 2}. Using a combination of high resolution transmission electron microscopy and Raman spectroscopy, it is found that AlN nanowires are completely relaxed, which has been assigned to the compliant character of SiO{sub 2}. Elastic strain relaxation of AlN nanowires has been further confirmed by photoluminescence experiments, showing in addition that spectra are dominated by near-band edge emission.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Elastic-Plastic Fracture Mechanics Analysis of Critical Flaw Size in ARES I-X Flange-to-Skin Welds

NASA's Ares 1 Upper Stage Simulator (USS) is being fabricated from welded A516 steel. In order to insure the structural integrity of these welds it is of interest to calculate the critical initial flaw size (CIFS) to establish rational inspection requirements. The CIFS is in turn dependent on the critical final flaw size (CFS), as well as fatigue flaw growth resulting from transportation, handling and service-induced loading. These calculations were made using linear elastic fracture mechanics (LEFM), which are thought to be conservative because they are based on a lower bound, so called elastic, fracture toughness determined from tests that displayed significant plasticity. Nevertheless, there was still concern that the yield magnitude stresses generated in the flange-to-skin weld by the combination of axial stresses due to axial forces, fit-up stresses, and weld residual stresses, could give rise to significant flaw-tip plasticity, which might render the LEFM results to be non-conservative. The objective of the present study was to employ Elastic Plastic Fracture Mechanics (EPFM) to determine CFS values, and then compare these values to CFS values evaluated using LEFM. CFS values were calculated for twelve cases involving surface and embedded flaws, EPFM analyses with and without plastic shakedown of the stresses, LEFM analyses, and various welding residual stress distributions. For the cases examined, the computed CFS values based on elastic analyses were the smallest in all instances where the failures were predicted to be controlled by the fracture toughness. However, in certain cases, the CFS values predicted by the elastic-plastic analyses were smaller than those predicted by the elastic analyses; in these cases the failure criteria were determined by a breakdown in stress intensity factor validity limits for deep flaws (a greater than 0.90t), rather than by the fracture toughness. Plastic relaxation of stresses accompanying shakedown always increases the calculated CFS values compared to the CFS values determined without shakedown. Thus, it is conservative to ignore shakedown effects.

Chell, G. Graham↗

A Passive Magnetoelastic Radiation Sensor

A passive gamma detection technology, consisting of a fielded sensor and a separate analysis system, is described. The sensor is a small cylinder, about 2.5 mm in diameter and 15 mm in length. It requires no onboard power sources or physical connections for power or data transfer, and retains its cumulative response to radiation. The sensor consists of an amorphous magnetoelastic wire held in a longitudinally-stressed state by a radiation-sensitive material. When the radiation-sensitive material is subjected to gamma radiation, it mechanically degrades, relaxing the stress on the wire and lowering the wire’s magnetic permeability. The changes in permeability are observed by switching the magnetic domains in the wire and measuring the reduction in the Faraday voltage as the stress is diminished. The analysis package is built around an excitation-detection coil set and can communicate wirelessly with the sensor through a metallic or nonmetallic barrier at distances up to about 25 mm. The sensor response is linear up to a dose of at least 7 kGy.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

MECHANICAL PROPERTIES OF CATHODE-INTERCONNECT INTERFACES IN PLANAR SOFCs

The residual stresses in manganese cobaltite, i.e., Mn1.5Co1.5O4, coatings applied onto alloys 441 and Crofer 22 APU were determined by X-Ray Diffraction. The residual stresses were found to be tensile at 800 C for both systems. The residual stress for spinel-coated AL441 relaxed with time and reached a value of 0.16 0.02 GPa after 300 minutes. The stress relaxation process was slower for spinel-coated Crofer and reached a value of 0.23 0.01 GPa after 500 minutes. Four-point bend SENB testing technique was used to evaluate the toughness of the interfaces between LSM10, i.e., (La0.9Sr0.1)0.98MnO3+δ, and spinel-coated AL441 and Crofer. Sandwich test specimens were prepared by sintering the LSM10 layer at 900 C for four hours in air or under PO2 cyclic conditions. The strain energy release rate was found to be 1.52 0.11 J/m2 for regular sintering and 1.47 0.15 J/m2 for sintering with cyclic PO2 treatment. This difference was found to be statistically insignificant.

36 MATERIALS SCIENCE↗

Plasma anisotropy and the radial particle flux in a rippled tokamak

We show that an often used relation between the radial particle flux and the divergence of the gyrotropic stress is an algebraic identity, unrelated to momentum conservation. Our calculation is completely general with regard to toroidal geometry and plasma collisionality. The result bears on the role of anisotropy in momentum relaxation and also clarifies certain methodological issues.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Derivation of Hydrodynamic Equations for Binary Gas Mixture

Velocities, densities, pressures, stresses, temperatures, heat fluxes and internal energies of each gas are individually defined. Moment equations for mass, momentum and energy of both gases are separately derived on basis of Boltzmann equations. Momentum equations have velocity relaxation terms between different gases and energy equations have velocity and temperature relaxation terms between those.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Pre-Stressed Viscoelastic Composites: Effective Incremental Moduli and Band-Gap Tuning

We study viscoelastic wave propagation along pre-stressed nonlinear elastic composite bars. In the pre-stressed state we derive explicit forms for the effective incremental storage and loss moduli with dependence on the pre-stress. We also derive a dispersion relation for the effective wavenumber in the case of arbitrary frequency, hence permitting a study of viscoelastic band-gap tuning via pre-stress.

36 MATERIALS SCIENCE↗

Catastrophic degradation of the interface of epitaxial silicon carbide on silicon at high temperatures

Epitaxial cubic silicon carbide on silicon is of high potential technological relevance for the integration of a wide range of applications and materials with silicon technologies, such as micro electro mechanical systems, wide-bandgap electronics, and graphene. The hetero-epitaxial system engenders mechanical stresses at least up to a GPa, pressures making it extremely challenging to maintain the integrity of the silicon carbide/silicon interface. In this work, we investigate the stability of said interface and we find that high temperature annealing leads to a loss of integrity. High–resolution transmission electron microscopy analysis shows a morphologically degraded SiC/Si interface, while mechanical stress measurements indicate considerable relaxation of the interfacial stress. From an electrical point of view, the diode behaviour of the initial p-Si/n-SiC junction is catastrophically lost due to considerable inter-diffusion of atoms and charges across the interface upon annealing. Temperature dependent transport measurements confirm a severe electrical shorting of the epitaxial silicon carbide to the underlying substrate, indicating vast predominance of the silicon carriers in lateral transport above 25 K. This finding has crucial consequences on the integration of epitaxial silicon carbide on silicon and its potential applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Robust, Brillouin Active Embedded Fiber-Is-The-Sensor System in Smart Composite Structures

Extensive review of our proposed sensing scheme, based mainly on the forward Guided Acoustic Wave Brillouin Scattering (GAWBS) with backward stimulated Brillouin scattering (sBs) as an auxiliary scheme for system fault tolerance has been completed during this project period. This preliminary study is conducted for a number of reasons. The most significant reasons lie in the essential capability of the system to measure temperature and pressure. These two measurands have been proposed to be sensed by sBs in our proposal. Temperature and pressure/strain are important measurands in structural monitoring, so that the effectiveness of sensing by sBs needs to be further examined. It has been pointed out initially that sBs shift will be dependent on temperature and pressure/strain simultaneously. The shift versus temperature or strain is linear. Now, the question is how can these two measurands be separated when sBs is used to sense an environment, in which both temperature and strain are changing simultaneously. Typical sBs shift plotted versus strain and varying temperature is shown in Fig. 1. As is clear, a fiber initially stressed will relax with rising temperature. This is verified by a displacement to the right with rising temperature of the sBs shift vs strain curves in the figure. A way to circumvent this ambiguity is by employing two fibers, one pre-stressed and the other is a free fiber. The latter will measure temperature and subtracting data in the latter fiber from those of the former will give us net strain readings. This is a laborious approach, since it involves the use of two identical fibers, and this is hard to accomplish, especially when many sensors are needed. Additional multiplexing of the data stream for data subtraction becomes a necessity.

Yu, Chung↗