Search NASA⌕ Search

SEARCH · Search NASA

Results for “SWEEP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Flow visualization study of spanwise blowing applied to the F-4 fighter aircraft configuration

Water tunnel studies were performed to define the changes that occur in vortex flow fields above the wing due to spanwise blowing over the inboard and outboard wing panels and over the trailing-edge flaps. Flow visualization photographs were obtained for angles of attack up to 30 deg and sideslip angles up to 10 deg. The sensitivity of the vortex flows to changes in flap deflection angle, nozzle position, and jet momentum coefficient was determined. Deflection of the leading edge flap delayed flow separation and the formation of the wing vortex to higher angles of attack. Spanwise blowing delayed the breakdown of the wing vortex to farther outboard and to higher angles of attack. Spanwise blowing over the trailing edge flap entrained flow downward, producing a lift increase over a wide range of angles of attack. The sweep angle of the windward wing was effectively reduced in sideslip. This decreased the stability of the wing vortex, and it burst farther inboard. Reduced wing sweep required a higher blowing rate to maintain a stable vortex. A vortex could be stabilized on the outboard wing panel when an outboard blowing nozzle was used. Blowing from both an inboard and an outboard nozzle was found to have a favorable interaction.

Lorincz, D. J.↗
NASA NTRS1981

Preliminary results of buffet tests in a cryogenic wind tunnel

Buffet tests of two wings with different leading-edge sweep show that it is feasible to use the standards wing root bending moment technique in a cryogenic wing tunnel. The results for the 65 deg sweep delta wing indicate the importance of matching the reduced frequency parameter in model tests for planforms which are sensitive to reduced frequency parameter if quantitative buffet measurements are required. The unique ability of a pressurized cryogenic wind tunnel to separate the effects of Reynolds number and of aeroelastic distortion by variations in the tunnel stagnation temperature and pressure was demonstrated.

Boyden, R. P.↗
NASA NTRS1980

Boundary layer stability analysis of a natural laminar flow glove on the F-111 TACT airplane

A natural laminar flow airfoil has been developed as a part of the aircraft energy efficiency program. A NASA flight program incorporating this airfoil into partial wing gloves on the F-111 TACT airplane was scheduled to start in May, 1980. In support of this research effort, an extensive boundary layer stability analysis of the partial glove has been conducted. The results of that analysis show the expected effects of wing leading-edge sweep angle, Reynolds number, and compressibility on boundary layer stability and transition. These results indicate that it should be possible to attain on the order of 60% laminar flow on the upper surface and 50% laminar flow on the lower surface for sweep angles of at least 20 deg, chord Reynolds numbers of 25 x 10 to the 6th and Mach numbers from 0.81 to 0.85.

Runyan, L. J.↗
NASA NTRS1982

Summary and recent results from the NASA advanced High Speed Propeller Research Program

Advanced high-speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. The current status of the NASA research program on high-speed propeller aerodynamics, acoustics, and aeroelastics is described. Recent wind tunnel results for five 8- to 10-blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing near-field cruise noise by dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some initial lifting line results are compared with propeller force and probe data. Some initial laser velocimeter measurements of the flow field velocities of an 8-bladed 45 deg swept propeller are shown. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller near-field noise data with linear acoustic theory indicate that the theory adequate predicts near-field noise for subsonic tip speeds but overpredicts the noise for supersonic tip speeds. Potential large gains in propeller efficiency of 7 to 11 percent at Mach 0.8 may be possible with advanced counter-rotation propellers.

Mitchell, G. A.↗
NASA NTRS1981

The development of cryogenic wind tunnels and their application to maneuvering aircraft technology

Cryogenic wind tunnels are considered as a means of studying high Reynolds number (Re) complicated flows encountered by high maneuvering lift and high angles of attack characteristic of modern fighter aircraft. Large decreases in the viscous force while the inertial force remains constant are provided by the use of cryogenic facilities. A 2.5 m square tunnel is nearing completion at the National Transonic Facility (NTF), and will be driven by synchronous motors having a total power of 120,000 hp. The tunnel, using N2 as the cryogenic fluid, will allow large Re sweeps at constant dynamic pressure and dynamic pressure, and aeroelastic sweeps at constant Re; full altitude (air density) and acceleration force simulation will also be possible. Advances in model and strain gage balance technologies for use at the NTF are outlined, and experiments with buffet are described.

Polhamus, E. C.↗
NASA NTRS1981

AD-1 oblique wing aircraft program

A NASA program for evaluation of the handling and flying characteristics of the AD-1 oblique wing aircraft is discussed. The vehicle was flown to compare wind tunnel predictions with aerodynamic data, explore the control system requirements, and obtain a preliminary assessment of the aeroelastic effects. The fiberglass sandwich skin aircraft is designed for 8 g positive and 4 g negative loading at 175 knots, while the wing pivot can withstand 25 g loading. Flight monitoring was accomplished with a 41 channel pulse code modulation system for telemetry and by averaging of pilot ratings. Maneuvering tests are outlined, noting that pilot ratings indicated acceptable handling at up to 50 deg sweep. It is concluded that acceptable flying qualities can be achieved with a 60 deg sweep, and that aeroelastic tailoring can be used to satisfy cruise design technology.

Mcmurtry, T. C.↗
NASA NTRS1981

Thematic mapper - An overview of spectral band registration

The Thematic Mapper (TM) is a high-resolution radiometer designed for earth resources classification and mapping. The TM employs multispectral scanning in a near polar orbit to sweep a 185-km swath. Data are obtained through a combination of spacecraft motion and the sweeping action of the scan mirror. These data are transmitted either directly to ground stations around the world or through a relay to the central data processing facility at White Sands, NM. Seven spectral passbands are employed, and applications include coastal water mapping, soil vegetation differentiation, biomass surveys, water body delineation, vegetation moisture measurement, plant heat stress management, and hydrothermal mapping. Attention is given to the scan mirror assembly, scan nonlinearities, the characterization and compensation of scan profiles, experimental performance, and a procedure for midscan correction.

Freudenstein, W. H.↗
NASA NTRS1982

Dynamic load measurements with delta wings undergoing self-induced roll-oscillations

The aerodynamic forces acting on a delta wing, mounted on a free-to-roll sting-balance apparatus, were measured. Two wing planforms having leading edge sweeps of 76 and 80 deg were tested, but only the wing with the 80 deg sweep would undergo periodic self-induced roll oscillation. The time dependent forces and roll angles for this wing were then recorded for various test conditions. In these tests a considerable drop in the average normal force of the free-to-roll wing was measured, relative to the normal force obtained in the static tests. Also, the helium-bubble flow visualization technique was used to gain some insight into the periodic motion of the separated leading edge vortices.

Levin, D.↗
NASA NTRS1982

Noise of the 10-bladed, 40 deg swept SR-6 propeller in a wind tunnel

The noise generated by supersonic helical-tip-speed propellers is a likely cabin environment problem for future airplanes powered by these propellers. Three propeller models with different tip sweeps. SR-1M, SR-2, and SR-3, designed for 244 m/sec (800 ft/sec) tip speed at a flight Mach number of 0.8 were previously tested in the NASA Lewis 8- by 6-Foot Wind Tunnel. In order to investigated another design point condition, the SR-6 propeller was designed for 213 m-sec (700 ft/sec) tip speed at a flight Mach number of 0.8. The noise data from this propeller are reported herein. Curves of blade passing frequency noise versus tip Mach number (at constant advance ratio) showed that the SR-6 propeller behaved similarly to the SR-1M propeller. The noise of the SR-6 propeller at its design condition, helical tip Mach number of 1.07, is approximately 3 dB quieter than the SR-2 propeller at its higher design helical tip Mach number of 1.15, but about 2.5 dB noisier than SR-3 at its design condition. The helical tip Mach number shift of the steep noise rise followed the same progression as the blade sweep angle for all of the propellers. When operated at the SR-3 design point, the SR-6 propeller was approximately 1.5 dB quieter than SR-2 and 4 dB noisier than SR-3.

Dittmar, J. H.↗
NASA NTRS1983

Augmentation of Fighter-Aircraft Performance by Spanwise Blowing over the Wing Leading Edge

Spanwise blowing over the wing and canard of a 1:35 model of a close-coupled-canard fighter airplane configuration (similar to the Kfir-C2) was investigated experimentally in low-speed flow. Tests were conducted at airspeeds of 30 m/sec (Reynolds number of 1.8 x 10 to the 5th power based on mean aerodynamic chord) with angle-of-attack sweeps from -8 to 60 deg, and yaw-angle sweeps from -8 to 36 deg at fixed angles of attack 0, 10, 20, 25, 30, and 35 deg. Significant improvement in lift-curve slope, maximum lift, drag polar and lateral/directional stability was found, enlarging the flight envelope beyond its previous low-speed/maximum-lift limit. In spite of the highly swept (60 deg) leading edge, the efficiency of the lift augmentation by blowing was relatively high and was found to increase with increasing blowing momentum on the close-coupled-canard configuration. Interesting possibilities of obtaining much higher efficiencies with swirling jets were indicated.

Seginer, A.↗
NASA NTRS1983

Evaluation of LANDSAT-4 TM and MSS ground geometry performance without ground control

Techniques and software developed to characterize the Washington, D.C. scene were improved and are being systematically applied to an Imperial Valley, CA scene. Digital elevation files are being acquired. One hundred seventy-two tiepoints were located in the Imperial Valley scene. They were digitized from USGS maps to determine their lat-long coordinates. A least squares fit is currently being performed between line-sample image data and the lat-long positions of the tiepoints. Thematic mapper scanner sweeps were determined for the Imperial Valley P-data. VICAR jobs are currently under way to analyze sample-direction offsets between sweeps in the data, as well as band to band registration offsets. Tiepoint location is about to begin in the Harrisburg, PA scene.

Bryant, N. A.↗
NASA NTRS1983

Real-time flutter analysis of an active flutter-suppression system on a remotely piloted research aircraft

Flight-test results of the first three flights of an aeroelastic research wing are described. The flight flutter-test technique used to obtain real-time damping estimates from fast-frequency sweep data was obtained and the open-loop flutter boundary determined. Nyquist analyses of sweep maneuvers appear to provide additional valuable information about flutter suppression system operation, both in terms of phase-margin estimates and as a means of evaluating maneuver quality. An error in implementing the flutter-suppression system required in a one-half nominal gain configuration, which caused the wing to be unstable at lower Mach numbers than anticipated, and the vehicle experienced closed-loop flutter on its third flight. Real-time flutter-testing procedures were improved.

Gilyard, G. B.↗
NASA NTRS1983

Noise generation by a finite span swept airfoil

An analysis is developed for the noise generated by a convected gust interacting with a single swept airfoil. The airfoil spans a channel with infinite parallel walls which contains a uniform subsonic mean flow. High frequency gusts, for which the noise generation is concentrated at the airfoil leading edge, are considered. The solution utilizes the Wiener-Hopf technique applied to the equations in nonorthogonal coordinates. Closed form expressions for the farfield acoustic pressure are obtained. The convected gust is assumed to be a plane wave, i.e., the lowest order spanwise mode. Because of the swept leading edge, this convected gust generates acoustic modes of all orders. At high frequencies and low Mach numbers, moderate sweep angles produce substantial noise reductions. The residual acoustic energy is carried mainly by the higher modes. The airfoil sweep also modulates the basic high frequency farfield directivity, producing lobed patterns. The angular modulation of the directivity patterns is most pronounced for the lower order modes.

Kerschen, E. J.↗
NASA NTRS1983

Measured inplane stability characteristics in hover for an advanced bearingless rotor

A study was made of the inplane stability characteristics of a model of an advanced bearingless main rotor. The four-bladed rotor system was tested for aeroelastic stability in hover for both isolated and body-free conditions. Variations in several hub design parameters were tested, including blade coning and sweep angles, blade inplane structural damping, pitch-link location (delta-free effect), and fuselage structural damping. An analysis of the experimental results shows that parametric stability trends observed from isolated-rotor studies may yield incorrect conclusions regarding coupled rotor-body characteristics. For body-free conditions, the baseline rotor configuration resulted in the best stability margins at 1-g thrust as well as at the nominal design rotor speed. Blade built-in coning had little effect on the body-free damping levels at the inplane/body resonance points. Introducing blade sweep destabilized the rotor at the inplane/body pitch resonance.

Weller, W. H.↗
NASA NTRS1983

Numerical simulation of the leading-edge separation vortex for a wing and strake-wing configuration

In the present investigation, the 'thin layer' Navier-Stokes equations are used to compute the flow about a delta wing and a strake-delta wing configuration. Both configurations possess blunt noses and rounded leading edges. The computational grid about these configurations is generated using a newly developed three-dimensional grid-generation code which solves a set of Poisson equations with spherical coordinate variables using an alternating direction implicit (ADI) scheme. Computational results are obtained for an isolated wing with 60 deg sweep and a strake-wing configuration with 80-60 deg sweep. Computations for angles of attack in the range from 6 to 30 deg are presented. Attention is given to the effect of the angle of attack, the Mach number, and the Reynolds number. Theoretical results are compared with experimental data.

Fujii, K.↗
NASA NTRS1983

Application of slender wing benefits to military aircraft

A review is provided of aerodynamic research conducted at the Langley Research Center with respect to the application of slender wing benefits in the design of high-speed military aircraft, taking into account the supersonic performance and leading-edge vortex flow associated with very highly sweptback wings. The beginning of the development of modern classical swept wing jet aircraft is related to the German Me 262 project during World War II. In the U.S., a theoretical study conducted by Jones (1945) pointed out the advantages of the sweptback wing concept. Developments with respect to variable sweep wings are discussed, taking into account early research in 1946, a joint program of the U.S. with the United Kingdom, the tactical aircraft concept, and the important part which the Langley variable-sweep research program played in the development of the F-111, F-14, and B-1. Attention is also given to hybrid wings, vortex flow theory development, and examples of flow design technology.

Polhamus, E. C.↗
NASA NTRS1983

Augmentation of fighter-aircraft performance by spanwise blowing over the wing leading edge

Spanwise blowing over the wing and canard of a 1:35 model of a close-coupled-canard fighter-airplane configuration (similar to the Kfir-C2) was investigated experimentally in low-speed flow. Tests were conducted at airspeeds of 30 m/sec (Reynolds number of 1.8 x 10 to the 5th power based on mean aerodynamic chord) with angle-of-attack sweeps from -8 deg to 60 deg, and yaw-angle sweeps from -8 deg to 36 deg at fixed angles of attack 0 deg, 10 deg, 20 deg, 25 deg, 30 deg, and 35 deg. Significant improvement in lift-curve slope, maximum lift, drag polar and lateral/directional stability was found, enlarging the flight envelope beyond its previous low-speed/maximum-lift limit. In spite of the highly swept (60 deg) leading edge, the efficiency of the lift augmentation by blowing was relatively high and was found to increase with increasing blowing momentum on the close-coupled-canard configuration. Interesting possibilities of obtaining much higher efficiencies with swirling jets were indicated.

Seginer, A.↗
NASA NTRS1983

Aeroelastic analysis for propellers - mathematical formulations and program user's manual

Mathematical development is presented for a specialized propeller dedicated version of the G400 rotor aeroelastic analysis. The G400PROP analysis simulates aeroelastic characteristics particular to propellers such as structural sweep, aerodynamic sweep and high subsonic unsteady airloads (both stalled and unstalled). Formulations are presented for these expanded propeller related methodologies. Results of limited application of the analysis to realistic blade configurations and operating conditions which include stable and unstable stall flutter test conditions are given. Sections included for enhanced program user efficiency and expanded utilization include descriptions of: (1) the structuring of the G400PROP FORTRAN coding; (2) the required input data; and (3) the output results. General information to facilitate operation and improve efficiency is also provided.

Bielawa, R. L.↗