Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface reflectance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of gas injection location and divertor surface material on ITER fusion power operation phase divertor performance assessed with SOLPS-ITER *

Abstract The ITER divertor design and performance assessment, primarily based on the SOLPS-4.3 burning plasma database (Pitts R. et al 2019 Nucl. Mater. Energy 20 100696), assumes the use of beryllium (Be) as the divertor surface material and the injection of gas from the main chamber top. However, the current ITER baseline favors gas injection from the more toroidally symmetric sub-divertor region. This paper evaluates the implications of these assumptions for divertor performance in the ITER fusion power operation phase. The impact of the divertor surface material and the gas injection location on the main ions mirrors the hydrogen only low power phase scenario shown in Park J.-S. et al (2020 Nucl. Fusion 61 016021). However, during burning plasma operation, extrinsic impurity seeding will be required. In the case of neon (Ne), studied here, impurity retention is influenced by both the divertor surface material and the fueling location. Neon leakage increases due to more energetic reflection from tungsten than beryllium, but equivalent divertor performance can be achieved by adjusting the neon seeding rate. While the impurity seeding location does not affect the distributions of impurity or radiation, the fueling location does. Top fueling provides local ionization sources mainly in the mid-SOL under detached conditions, enhancing divergences of the flux there (source-driven flow), bringing stagnation points close to the fueling location, and equilibrating flows towards both targets. In contrast, the global flow pattern (in the absence of fluid drifts) in the case of sub-divertor fueling is biased towards the inner target. Impurity flows, driven by force balance, largely mirror those of the main ion flow, including the stagnation point. The case with top fueling enhances Ne retention and corresponding radiation in the outer divertor, effectively reducing the total and peak target heat fluxes by 20%–40%, compared to the case with divertor fueling. Meanwhile, the case with outer target fueling also achieves similar reductions by enhancing plasma-neutral interactions. These results suggest the possibility that the selection of the fueling location and throughput can be used as an actuator to control impurity divertor retention and divertor radiation asymmetry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Epitaxial stabilization of thin films of the frustrated Ge-based spinels

Frustrated magnets can host numerous exotic many-body quantum and topological phenomena. GeNi 2 O 4 is a three-dimensional S=1 frustrated magnet with an unusual two-stage transition to the two-dimensional antiferromagnetic ground state, while GeCu 2 O 4 is a high-pressure phase with a strongly tetragonally elongated spinel structure and magnetic lattice formed by S=1/2 CuO 2 linear chains with frustrated interchain exchange interactions and exotic magnetic behavior. Here, we report on the thin-film epitaxial stabilization of these two compounds. The developed growth mode, surface morphology, crystal structure, and copper valence state were characterized by in situ reflection high-energy electron diffraction, atomic force microscopy, x-ray reflectivity, x-ray diffraction, x-ray photoelectron spectroscopy, and resonant x-ray absorption spectroscopy. Our results pave an alternative route to the comprehensive investigation of the puzzling magnetic properties of these compounds and the exploration of emergent features driven by strain.

36 MATERIALS SCIENCE↗
DOE OSTI2021

TRANSIENT THERMAL MODELING OF THE HIGH BURNUP DEMONSTRATION RESEARCH PROJECT CASK USING STAR-CCM+ AND COBRA-SFS

The Department of Energy in collaboration with the Electric Power Research Institute is in the process of conducting the High Burnup Demonstration Project. Where the objective is to characterize the performance of high-burnup fuel in long term storage. As part of this demonstration, a TN-32B dry storage cask was instrumented and loaded with spent nuclear fuel at North Anna Nuclear Generating Station in November 2017. The project cask provides a unique opportunity to gain information on spent fuel and cask performance from an in-service operational system. The cask was instrumented with thermocouples inside of the fuel assemblies, then loaded and dried using normal procedures. After the drying process a thermal soak period where the cask was left indoors was used to obtain steady temperatures for model comparison along with surface temperatures. This paper details thermal modeling validation work that was done to model both the steady state and transient cases. Two modeling tools were used to predict temperatures in the cask. The general purpose CFD and heat transfer code STAR-CCM+ was used with both a detailed pin-by-pin model was used along with a more efficient k-effective simplification. The other code is COBRA-SFS, a purpose-built detailed thermal modeling tool developed and maintained at PNNL. Results from all the modeling tools were compared blind to the test data. Each model utilized general design information and compared reasonably well to the blind steady state data using convection and surface temperature boundary conditions. Post-test adjustments were later made to better reflect the “as built” conditions of the cask. Based on lessons learned from the steady state analysis the vacuum drying process was modeled in both codes. Utilizing the measured loading conditions the transient models were able to compare very well with the measured data. Overall the project showed an ability to model spent fuel storage conditions very well and future work is planned to generalize the methodology used for vacuum drying.

Thermal Analysis, Spent Fuel, Dry Storage↗
DOE OSTI2023

Machine-learning-assisted analysis of transition metal dichalcogenide thin-film growth

In situ reflective high-energy electron diffraction (RHEED) is widely used to monitor the surface crystalline state during thin-film growth by molecular beam epitaxy (MBE) and pulsed laser deposition. With the recent development of machine learning (ML), ML-assisted analysis of RHEED videos aids in interpreting the complete RHEED data of oxide thin films. The quantitative analysis of RHEED data allows us to characterize and categorize the growth modes step by step, and extract hidden knowledge of the epitaxial film growth process. In this study, we employed the ML-assisted RHEED analysis method to investigate the growth of 2D thin films of transition metal dichalcogenides (ReSe2) on graphene substrates by MBE. Principal component analysis (PCA) and K-means clustering were used to separate statistically important patterns and visualize the trend of pattern evolution without any notable loss of information. Using the modified PCA, we could monitor the diffraction intensity of solely the ReSe2 layers by filtering out the substrate contribution. These findings demonstrate that ML analysis can be successfully employed to examine and understand the film-growth dynamics of 2D materials. Further, the ML-based method can pave the way for the development of advanced real-time monitoring and autonomous material synthesis techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Real-Time Monitoring of Strain Accumulation and Relief during Epitaxy of Ultrathin Co Ferrite Films with Varied Co Content

Ultrathin Co x Fe 3-x O 4 films of high structural quality and with different Co content (x = 0.6–1.2) were prepared by reactive molecular beam epitaxy on MgO(001) substrates. Epitaxy of these ferrite films is extensively monitored by means of time-resolved (operando) X-ray diffraction recorded in out-of-plane geometry to characterize the temporal evolution of the film structure. The Co ferrite films show high crystalline ordering and smooth film interfaces independent of their Co content. All Co x Fe 3-x O 4 films exhibit enhanced compressive out-of-plane strain during the early stages of growth, which partly releases with increasing film thickness. When the Co content of the ferrite films increases, the vertical-layer distances increase, accompanied by slightly increasing film roughnesses. The latter result is supported by surface-sensitive low-energy electron diffraction as well as X-ray reflectivity measurements on the final films. In contrast, the substrate–film interface roughness decreases with increasing Co content, which is confirmed with X-ray reflectivity measurements. In addition, the composition and electronic structure of the ferrite films is characterized by means of hard X-ray photoelectron spectroscopy performed after film growth. The experiments reveal the expected increasing Fe 3+ /Fe 2+ cation ratios for a higher Co content.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impacts of active satellite sensors' low-level cloud detection limitations on cloud radiative forcing in the Arctic

Previous studies revealed that satellites sensors with the best detection capability identify 25 %–40 % and 0 %–25 % fewer clouds below 0.5 and between 0.5–1.0 km, respectively, over the Arctic. Quantifying the impacts of cloud detection limitations on the radiation flux are critical especially over the Arctic Ocean considering the dramatic changes in Arctic sea ice. In this study, the proxies of the space-based radar, CloudSat, and lidar, CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations), cloud masks are derived based on simulated radar reflectivity with QuickBeam and cloud optical thickness using retrieved cloud properties from surface-based radar and lidar during the Surface Heat Budget of the Arctic Ocean (SHEBA) experiment. Limitations in low-level cloud detection by the space-based active sensors, and the impact of these limitations on the radiation fluxes at the surface and the top of the atmosphere (TOA), are estimated with radiative transfer model Streamer. The results show that the combined CloudSat and CALIPSO product generally detects all clouds above 1 km, while detecting 25 % (9 %) fewer in absolute values below 600 m (600 m to 1 km) than surface observations. These detection limitations lead to uncertainties in the monthly mean cloud radiative forcing (CRF), with maximum absolute monthly mean values of 2.5 and 3.4 Wm –2 at the surface and TOA, respectively. Cloud information from only CALIPSO or CloudSat lead to larger cloud detection differences compared to the surface observations and larger CRF uncertainties with absolute monthly means larger than 10.0 Wm –2 at the surface and TOA. The uncertainties for individual cases are larger – up to 30 Wm –2 . These uncertainties need to be considered when radiation flux products from CloudSat and CALIPSO are used in climate and weather studies.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Spectral Effects in Albedo and Rearside Irradiance Measurment for Bifacial Performance Estimation: Preprint

Albedo data are essential for accurate prediction of bifacial PV module performance. However, spectral response mismatch between PV modules and irradiance sensors used in albedometers can limit the accuracy of performance predictions. In order to provide quantitative assessment of this effect, we investigate via simulation the differences in spectrally responsive albedo measured with thermopile pyranometers and crystallinesilicon PV reference cells in comparison to a representative crystalline-silicon bifacial PV module for nine different representative ground surface materials. Calculations are performed using simulated solar spectra together with catalogued spectral reflectivity data distributed with the SMARTS simulation software. For the specific materials considered, the results show that albedo measurement using thermopile pyranometers could over or under-estimate the ground-reflected radiation usable by a bifacial PV module by up to 10%, versus only approximately 4% total range of variation for a PV reference cell.

Albedo↗
DOE OSTI2026

Structure of Layers Formed by [2-(3,6-Disubstituted-9 H -carbazol-9-yl)ethyl]phosphonic Acids on Metal Oxides

[2-(9 H -Carbazol-9-yl)ethyl]phosphonic acid (2PACz) and its derivatives are being used extensively as hole-transport layers in organic and perovskite solar cells due to their ability to modify electrode work function, surface wettability, and in some cases, to improve active-layer adhesion, while minimizing interfacial energy losses. The orientation and coverage of surface modifiers significantly impact these functional properties; however, the detailed structure and packing in these overlayers are challenging to investigate, leading to a lack of understanding of how this structure and packing influence performance and limiting the ability to rationally design molecular modifiers. Here, we investigate monolayers of 2-(9 H -carbazol-9-yl)ethyl phosphonic acid derivatives (from here on referred to as X-2PACz) on indium tin oxide (ITO) and alpha phase aluminum oxide (α-Al 2 O 3 ) using a combination of X-ray photoelectron spectroscopy (XPS), near-edge X-ray absorption fine structure (NEXAFS) spectroscopy, and X-ray reflectivity (XRR). By correlating elemental ratios, molecular orientation, and electron density profiles, we directly quantify surface coverage, layer thickness, and molecular tilt across a series of chemically related monolayers. We find that 2PACz and the X-2PACz derivatives form dense monolayers on α-Al 2 O 3 and ITO, with similar surface coverages on either substrate that are inversely proportional to molecular steric bulk. These surface coverage results indicate that X-2PACz is sterically limited in its monolayer surface packing density, as opposed to site limited. Despite surface packing density differences between molecules, the NEXAFS data show a constant average molecular orientation of 61° to 65° between the plane of the carbazole and the substrate for all the molecules on both substrates. These results increase our general understanding of 2PACz derivatives as they become increasingly useful in high performance solar cells.

NEXAFS↗
DOE OSTI2026

pH-Driven Restructuring of Hydration Layers and Cation Ad-sorption at the Alumina-Water Interface

Oxide-water interfaces underpin ion separation, catalysis, and electrochemical energy technologies, where the electrical double layer (EDL) controls adsorption, transport, and reactivity. Yet, the molecular-scale link between pH-dependent surface protonation, hydration-layer structure, and counter-ion adsorption remains poorly defined. Here, we combine in situ crystal truncation rod (CTR) and resonant anomalous X-ray reflectivity (RAXR) with streaming potential measurements and ab initio molecular dynamics (AIMD) simulations to resolve the chemical and structural evolution of the EDL at the single-crystal alumina (012)-water interface in 10 mM Rb+ over pH 3-12. CTR measurements reveal two distinct adsorbed water layers at ~2.2 and ~3.5 Å above the surface that each shift toward the substrate at transition pHs near 6.5 and 10.6, respectively, directly reflecting changes in primary hydration layer structure in response to the deprotonation of bridging and terminal aluminol groups. RAXR shows a 10-fold increase in Rb+ coverage and a decrease in mean adsorption height from ~3.5 to ~2.7 Å with increasing pH, indicating enhanced counter-ion binding accompanied by Stern layer contraction. Streaming potential measurements demonstrate that the zeta potential, i.e., potential at the hydrodynamic shear plane, is positive at pH 3 and becomes negative at pH ≥3.5. This negative charge magnitude increases with increasing pH, consistent with progressive surface deprotonation at higher pH. AIMD identifies inner- and outer-sphere Rb+ complexes whose adsorption heights and coordination geometries depend sensitively on the protonation state of surface oxygens, providing atomistic support for the experimentally inferred trends. These measurements establish two discrete, site-specific pH transitions in hydration-layer structure that track aluminol (de)protonation and quantitatively link them to a pH-driven contraction of the Stern layer (increasing Rb+ coverage and decreasing adsorption height). This provides a direct structural basis for connecting surface acid-base chemistry to ion binding distances at an oxide-water interface.

Electrical double layer (EDL), Surface protonation↗
DOE OSTI2021

Atomistic-Scale Simulations on Graphene Bending Near a Copper Surface

Molecular insights into graphene-catalyst surface interactions can provide useful information for the efficient design of copper current collectors with graphitic anode interfaces. As graphene bending can affect the local electron density, it should reflect its local reactivity as well. Using ReaxFF reactive molecular simulations, we have investigated the possible bending of graphene in vacuum and near copper surfaces. We describe the energy cost for graphene bending and the binding energy with hydrogen and copper with two different ReaxFF parameter sets, demonstrating the relevance of using the more recently developed ReaxFF parameter sets for graphene properties. Moreover, the draping angle at copper step edges obtained from our atomistic simulations is in good agreement with the draping angle determined from experimental measurements, thus validating the ReaxFF results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Improved Infrared Optical Constants from Pressed Pellets: II. Ellipsometric n and k Values for Ammonium Sulfate with Variability Analysis

Infrared spectral imaging is facilitated via the comparison of spectra recorded in situ to a databank of actual or synthetic infrared reflectance spectra. It has recently been shown that reference spectra corresponding to the many different morphological forms of the same chemical can be generated synthetically using the imaginary, k, and real, n, components of the complex refractive index, n~ = n + ik. One method to obtain the n and k vectors is infrared ellipsometry, which measures the changes in amplitude, tan ?, and phase, ?, of polarized light reflected from the sample both as a function of wavenumber and angle of incidence. The method requires specularly reflected light so best results are usually obtained with polished planar samples of large surface area. Due to the difficulties of obtaining such samples, however, we investigate the possibility of pressing powders of neat materials and obtaining the corresponding optical constants from the pellets. In this paper, variability in the sample pellet and preparation method is investigated, as is variability in the fitting procedure for the derived optical constants. The n/k vectors are derived from the measured ellipsometric parameters, tan ? and ?, as they are fit by an oscillator model which yield n(?) and k(?) vectors as a function of wavenumber, ?. Construction of the oscillator model is not automatic and depends on significant input from the analyst as well as the sample’s physical characteristics. For the pellet pressing, the experimental variability was found to be minimized for size-selected powdered samples as gauged by the minimal variance in ? and ? for three different pellets; similarly, the analytical precision for multiple measurements of the same pellet was also quite good, suggesting that a pressed pellet is a viable sample preparation method. The greatest variability came in the analytic fitting procedure with differences up to 20% arising from four different fits to the same data set. The final ellipsometric n/k data are compared to literature values obtained from crystalline (NH4)2SO4 samples as well as single-angle reflectance measurements that also used pressed pellets. Comparison with the previous literature values shows generally good agreement although higher k-values are observed for the independent sets of data derived from pressed pellets. These data are suggested as an improved set of optical constants for (NH4)2SO4.

optical constants, ellipsometry, ammonium sulfate,↗
DOE OSTI2024

Spin Textures at Conformal Surfaces and Interfaces: CRADA Final Report

The scientific and technological exploration of artificially designed three-dimensional magnetic nanostructures opens the path to exciting novel physical phenomena, originating from the increased complexity in spin textures, topology, and frustration in three dimensions. Theory predicts that the equilibrium magnetic ground state of two-dimensional systems which reflects the competition between symmetric (Heisenberg) and antisymmetric (Dzyaloshinskii-Moriya interaction (DMI)) exchange interaction is significantly modified on curved surfaces when the radius of local curvature becomes comparable to fundamental magnetic length scales. In this CRADA we performed collaboratively an experimental study of the spin texture in an 8 nm thin magnetic multilayer with growth-induced in-plane anisotropy and DMI deposited onto the curved surface of a 1.8µm long non-magnetic carbon nanowire with a 67 nm radius. The sample was fabricated in Juelich and with collaborators at BESSY in Berlin. Using magnetic soft x-ray tomography at the ALBA synchrotron in Spain, the three-dimensional spin configuration in this nanotube was retrieved with about 30nm spatial resolution. The transition between two vortex configurations on the two ends of the nanotube with opposite circulation occurs through a domain wall that is aligned at an inclined angle relative to the wire axis. Three-dimensional micromagnetic simulations support the experimental observations and represent a visualization of the curvature-mediated DMI. They also allow a quantitative estimate of the DMI value for the magnetic multilayered nanotube.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

GaAs Substrate Recycling Using in-situ Deposited NaCl Layers via Molecular Beam Epitaxy

This work presents an alternative method to conventional III-V substrate recycling methods via growth of NaCl on nearly-lattice matched GaAs (001) substrates. Reflection high energy electron diffraction and transmission electron microscopy confirm an epitaxial relationship between the NaCl layers and the underlying GaAs. If the sample is heated too much prior to GaAs deposition, the NaCl fully desorbs from the surface. The quality of the deposition of GaAs on NaCl ranges from amorphous at low temperature to polycrystalline at intermediate temperatures. Exposure to electron beams during growth results in larger and (001) textured grains. The substrate is separated from the GaAs film in seconds via submersion in water, revealing a substrate surface comparable to the original.

electron beams↗
DOE OSTI2025

Etching-Chemistry-Driven Ruthenium Doping on Ti 3 C 2 T x MXene for Optimizing Electrochemical Performance

We demonstrate that the etching chemistry used during MXene synthesis from Ti 3 AlC 2 MAX phase significantly influences surface functionalization and structural vacancies, which in turn affect ruthenium (Ru) ion interactions. Using hydrofluoric acid (HF) and ammonium bifluoride (NH 4 HF 2 ) as etchants, we obtained MXene surfaces with distinct functional groups and Ti vacancies that impact Ru ion interactions and electrochemical performance. Both MXene variants (labeled MX(H) and MX(N), respectively) exhibited negative zeta potentials in their pristine state, but upon the addition of Ru the zeta potential for MX(H) reached 12.9 mV while that for MX(N) remained negative at −6.4 mV. This adsorption resulted in a 14.4-fold increase in the specific capacitance of MX(H)/Ru compared to pristine MX(H), whereas MX(N)/Ru exhibited only a 4.4-fold increase over its pristine counterpart. X-ray diffraction analysis identified the formation of ammonium titanium oxide fluoride, (NH 4 ) 3 TiOF 5 , on MX(N), which likely contributed to its reduced Ru adsorption. X-ray photoelectron spectroscopy suggested the presence of Ti vacancies in both MXene variants; however, their behavior toward Ru accommodation differed markedly, with MX(H) showing the most obvious shift in the Ti 2p peak in the XPS survey spectrum, while MX(N) showed the most obvious shift in the C 1s peak. Electron paramagnetic resonance spectroscopy further demonstrated a distinct alteration in the spectral signatures of MX(H) upon Ru addition, in contrast to the negligible changes in MX(N), indicating effective passivation of the Ti defect sites in MX(H) via vacancy-assisted Ru doping. Cyclic voltammetry showed that Ru-incorporated MX(H) nanocomposites exhibit more efficient redox-active sites, as reflected in their higher capacitance values. These findings highlight the pivotal role of MXene surface chemistry in controlling cation adsorption, providing valuable insights for the rational design of high-performance electrodes.

2D surface engineering↗
DOE OSTI2022

Mesoscale evaluation of AMPS using AWARE radar observations of a wind and precipitation event over the Ross Island region of Antarctica

Surface, upper-air, and radar observations are used to assess the performance of the Antarctic Mesoscale Prediction System (AMPS) in simulating the mesoscale aspects of a wind and precipitation event over the Ross Island region of Antarctica that spanned January 16–20, 2016. The observations, collected during the Atmospheric Radiation Measurement (ARM) West Antarctic Radiation Experiment (AWARE), provide a unique dataset for evaluating AMPS, especially the radar observations that facilitate a three-dimensional depiction of winds and precipitation. Comparisons of AMPS forecast data with surface meteorology, balloon-sounding, and profiling radar observations at and above sites near McMurdo Station reveal a mixture of similarities and differences. A generally southerly flow is evident at low levels in both the AMPS simulations and observed Doppler radial velocities. AMPS winds are comparable to those observed at the surface and aloft in terms of magnitude, direction, and timing but the strongest simulated southerly flow is displaced eastward relative to the observations. AMPS-simulated reflectivity over the broader Ross Island region is more limited in areal extent and smaller in magnitude than observed by a scanning Doppler radar. Three episodes of surface precipitation are observed near McMurdo Station over the five-day event with peak rates of ~3 mm h -1 and a total accumulation of ~22 mm. However, AMPS produces no surface precipitation at that location over the five-day event due to a low-level dry bias in the forecasts. Herein, the results show the first observationally based three-dimensional understanding of meteorology in the Ross Island region.

AMPS↗
DOE OSTI2023

Climate response to off-equatorial stratospheric sulfur injections in three Earth system models – Part 1: Experimental protocols and surface changes

There is now substantial literature on climate model studies of equatorial or tropical stratospheric SO 2 injections that aim to counteract the surface warming produced by rising concentrations of greenhouse gases. Here we present the results from the first systematic intercomparison of climate responses in three Earth system models wherein the injection of SO 2 occurs at different latitudes in the lower stratosphere: CESM2-WACCM6, UKESM1.0 and GISS-E2.1-G. The first two use a modal aerosol microphysics scheme, while two versions of GISS-E2.1-G use a bulk aerosol (One-Moment Aerosol, OMA) and a two-moment (Multiconfiguration Aerosol TRacker of mIXing state, MATRIX) microphysics approach, respectively. Our aim in this work is to determine commonalities and differences between the climate model responses in terms of the distribution of the optically reflective sulfate aerosols produced from the oxidation of SO 2 and in terms of the surface response to the resulting reduction in solar radiation. A focus on understanding the contribution of characteristics of models transport alongside their microphysical and chemical schemes, and on evaluating the resulting stratospheric responses in different models, is given in the companion paper (Bednarz et al., 2023). The goal of this exercise is not to evaluate these single-point injection simulations as stand-alone proposed strategies to counteract global warming; instead we determine sources and areas of agreement and uncertainty in the simulated responses and, ultimately, the possibility of designing a comprehensive intervention strategy capable of managing multiple simultaneous climate goals through the combination of different injection locations. We find large disagreements between GISS-E2.1-G and the CESM2-WACCM6 and UKESM1.0 models regarding the magnitude of cooling per unit of aerosol optical depth (AOD) produced, which varies from 4.7 K per unit of AOD in CESM2-WACCM6 to 16.7 K in the GISS-E2.1-G version with two-moment aerosol microphysics. By normalizing the results with the global mean response in each of the models and thus assuming that the amount of SO 2 injected is a free parameter that can be managed independently, we highlight some commonalities in the overall distributions of the aerosols, in the inter-hemispheric surface temperature response and in shifts to the Intertropical Convergence Zone, as well as some areas of disagreement, such as the extent of the aerosol confinement in the equatorial region and the efficiency of the transport to polar latitudes. In conclusion, we demonstrate that it is possible to use these simulations to produce more comprehensive injection strategies in multiple climate models. However, large differences in the injection magnitudes can be expected, potentially increasing inter-model spreads in some stratospheric quantities (such as aerosol distribution) while reducing the spread in the surface response in terms of temperature and precipitation; furthermore, the selection of the injection locations may be dependent on the models' specific stratospheric transport.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Coating to cool a surface by passive radiative cooling

Disclosed herein in is a radiative cooling formulation comprising a first component with >55% reflectance in a wavelengths range of 0.3 to 2.5 microns, a second component with >0.85 peak thermal emissivity in a window range of 4 to 35 microns, and a third component to mechanically bind together a mixture of the first and second components.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Coating to cool a surface by passive radiative cooling

Disclosed herein in is a radiative cooling formulation including a first component with >55% reflectance in a wavelengths range of 0.3 to 2.5 microns, a second component with a first thermal emissivity peak value greater than 0.85 at a first wavelength in a range of 8 to 13 microns (μm), and a third component to mechanically bind together a mixture of the first component and second component.

Van Overmeere, Quentin↗