Search NASA⌕ Search

SEARCH · Search NASA

Results for “TESTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Results of aerodynamic heat transfer tests of a 0.0175-scale model of the Rockwell International Space Shuttle Orbiter 139 (model number 22-0) in the NASA/Ames 3.5-foot hypersonic wind tunnel (test OH6)

The results of a hypersonic wind tunnel test program conducted using a 0.0175 scale thin-skin thermocouple model of the Space Shuttle Orbiter to obtain aerodynamic heat transfer data on the Orbiter under simulated reentry conditions were presented. The test program was conducted at a Mach number of 7.3 and a freestream Reynolds number ranging between 1.0 and 6.0 million/foot. The model was tested for angles of attack ranging between 10 deg and 30 deg and a sideslip angle of 0 deg. The model was constructed of 15-5 PH stainless steel with the instrumented areas machined to a nominal skin thickness of 0.030 in. The model instrumentation consisted of 288 iron-constantan thermocouples spot welded to the skin inner surface, but only 75 of these were used in this test program. A high-speed, analog-to-digital data acquisition system was used to record data on magnetic tape.

Dye, W. H.↗
NASA NTRS1975

Shake Test of a Propeller Test Rig in the 40- by 80-Foot Wind Tunnel

A shake test was conducted to determine the dynamic characteristics of a propeller test rig in the Ames 40- by 80-Foot Wind Tunnel. The rotor off hub transfer function (acceleration per unit force as a function of frequency) was measured in the longitudinal, lateral, and vertical directions for shaft angles of 0 and 90 deg corresponding to propeller and helicopter operation, respectively. The dynamic data are summarized for the configurations tested, giving the following properties for each mode identified: the natural frequency, the hub response at resonance, the damping coefficient, the damping ratio, and the modal mass. The complete transfer functions are presented, and the detailed test results are included.

Johnson, W.↗
NASA NTRS1973

GEOS-C coherent C-band transponder test procedure for spacecraft level tests

Procedures for the performance of two tests (electrical and airlink) for the transponder are outlined. The C-band test console used in performing the above tests is described (circuit diagrams and block diagrams), and equipment specifications are given. Calibration of the test equipment is also discussed.

Selser, A. R.↗
NASA NTRS1975

Small scale noise and wind tunnel tests of upper surface blowing nozzle flap concepts. Volume 1. Aerodynamic test results

The results and analyses of aerodynamic and acoustic studies conducted on the small scale noise and wind tunnel tests of upper surface blowing nozzle flap concepts are presented. Various types of nozzle flap concepts were tested. These are an upper surface blowing concept with a multiple slot arrangement with seven slots (seven slotted nozzle), an upper surface blowing type with a large nozzle exit at approximately mid-chord location in conjunction with a powered trailing edge flap with multiple slots (split flow or partially slotted nozzle). In addition, aerodynamic tests were continued on a similar multi-slotted nozzle flap, but with 14 slots. All three types of nozzle flap concepts tested appear to be about equal in overall aerodynamic performance but with the split flow nozzle somewhat better than the other two nozzle flaps in the landing approach mode. All nozzle flaps can be deflected to a large angle to increase drag without significant loss in lift. The nozzle flap concepts appear to be viable aerodynamic drag modulation devices for landing.

Renselaer, D. J.↗
NASA NTRS1978

Test data report, low speed wind tunnel tests of a full scale lift/cruise-fan inlet, with engine, at high angles of attack

A low speed wind tunnel test of a fixed lip inlet with engine, was performed. The inlet was close coupled to a Hamilton Standard 1.4 meter, variable pitch fan driven by a lycoming T55-L-11A engine. Tests were conducted with various combinations of inlet angle of attack freestream velocities, and fan airflows. Data were recorded to define the inlet airflow separation boundaries, performance characteristics, and fan blade stresses. The test model, installation, instrumentation, test, data reduction and final data are described.

Shain, W. M.↗
NASA NTRS1979

X-band slotted array test panel and test fixture

Data from the development of the X-band slotted array test band, X-band array test fixture, and the X/L-band test fixture for the Support Instrumentation Requirements program are documented. An X-band array was built and installed with an existing L-band module in such a way as to permit antenna pattern measurements in a series of nonplanar configurations that might simulate the thermal effects of nonuniform solar illumination on the array in a space environment. This was accomplished with eight X-band subpanels mounted adjacently on individually adjusted supports which were then co-mounted to a larger frame which served to mount and physically distort the existing L-band module. The L-band module is a heavy electrical breadboard array section that was fabricated to demonstrate the performance capabilities of a slotted waveguide array at L-band frequencies. Drawings, mechanical analysis, and descriptions of test configurations are presented.

Source record↗
NASA NTRS1981

Results of the Mission Profile Life Test first test segment - Thruster J1

A series of long term test segments of 30 cm diameter mercury bombardment thrusters is being conducted as the Mission Profile Life Test. The first 4000 hour segment has been completed with the J series thruster, J1. Thruster and power processing units were controlled by computer with software algorithms governing normal functions of startup, throttle, and shutdown as well as automatically handling a variety of off-normal conditions. Thruster operation includes a discussion of the test chronology describing notable events and their significance. Post-test examination provides insight into thruster lifetime. Results are consistent with mission requirements of 15,000 hours at 2A

James, E. L.↗
NASA NTRS1984

Fastener load tests and retention systems tests for cryogenic wind-tunnel models

A-286 stainless steel screws were tested to determine the tensile load capability and failure mode of various screw sizes and types at both cryogenic and room temperature. Additionally, five fastener retention systems were tested by using A-286 screws with specimens made from the primary metallic alloys that are currently used for cryogenic models. The locking system effectiveness was examined by simple no-load cycling to cryogenic temperatures (-275 F) as well as by dynamic and static loading at cryogenic temperatures. In general, most systems were found to be effective retention devices. There are some differences between the various devices with respect to ease of application, cleanup, and reuse. Results of tests at -275 F imply that the cold temperatures act to improve screw retention. The improved retention is probably the result of differential thermal contraction and/or increased friction (thread-binding effects). The data provided are useful in selecting screw sizes, types, and locking devices for model systems to be tested in cryogenic wind tunnels.

Wallace, J. W.↗
NASA NTRS1986

Ground vibration test results for Drones for Aerodynamic and Structural Testing (DAST)/Aeroelastic Research Wing (ARW-1R) aircraft

The drones for aerodynamic and structural testing (DAST) project was designed to control flutter actively at high subsonic speeds. Accurate knowledge of the structural model was critical for the successful design of the control system. A ground vibration test was conducted on the DAST vehicle to determine the structural model characteristics. This report presents and discusses the vibration and test equipment, the test setup and procedures, and the antisymmetric and symmetric mode shape results. The modal characteristics were subsequently used to update the structural model employed in the control law design process.

Cox, T. H.↗
NASA NTRS1985

Extended testing of a general contextual classifier using the massively parallel processor - Preliminary results and test plans

Earlier encouraging test results of a contextual classifier that combines spatial and spectral information employing a general statistical approach are expanded. The earlier results were of limited meaning because they were produced from small (50-by-50 pixel) data sets. An implementation of the contextual classifier on NASA Goddard's Massively Parallel Processor (MPP) is presented; for the first time the MPP makes feasible the testing of the classifier on large data sets (a 12-hour test on a VAX-11/780 minicomputer now takes 5 minutes on the MPP). The MPP is a Single-Instruction, Multiple Data Stream computer, consisting of 16,384 bit serial microprocessors connected in a 128-by-128 mesh array with each element having data transfer connections with its four nearest neighbors so that the MPP is capable of billions of operations per second. Preliminary results are given (with more expected for the conference) and plans are mentioned for extended testing of the contextual classifier on Thematic Mapper data sets.

Tilton, J. C.↗
NASA NTRS1987

Small-scale rotor test rig capabilities for testing vibration alleviation algorithms

A test was conducted to assess the capabilities of a small scale rotor test rig for implementing higher harmonic control and stability augmentation algorithms. The test rig uses three high speed actuators to excite the swashplate over a range of frequencies. The actuator position signals were monitored to measure the response amplitudes at several frequencies. The ratio of response amplitude to excitation amplitude was plotted as a function of frequency. In addition to actuator performance, acceleration from six accelerometers placed on the test rig was monitored to determine whether a linear relationship exists between the harmonics of N/Rev control input and the least square error (LSE) identification technique was used to identify local and global transfer matrices for two rotor speeds at two batch sizes each. It was determined that the multicyclic control computer system interfaced very well with the rotor system and kept track of the input accelerometer signals and their phase angles. However, the current high speed actuators were found to be incapable of providing sufficient control authority at the higher excitation frequencies.

Jacklin, Stephen A.↗
NASA NTRS1987

Space station data management system - A common GSE test interface for systems testing and verification

This paper examines the fundamental problems and goals associated with test, verification, and flight-certification of man-rated distributed data systems. First, a summary of the characteristics of modern computer systems that affect the testing process is provided. Then, verification requirements are expressed in terms of an overall test philosophy for distributed computer systems. This test philosophy stems from previous experience that was gained with centralized systems (Apollo and the Space Shuttle), and deals directly with the new problems that verification of distributed systems may present. Finally, a description of potential hardware and software tools to help solve these problems is provided.

Martinez, Pedro A.↗
NASA NTRS1988

Propfan test assessment testbed aircraft stability and control/performance 1/9-scale wind tunnel tests

One-ninth scale wind tunnel model tests of the Propfan Test Assessment (PTA) aircraft were performed in three different NASA facilities. Wing and propfan nacelle static pressures, model forces and moments, and flow field at the propfan plane were measured in these tests. Tests started in June 1985 and were completed in January 1987. These data were needed to assure PTA safety of flight, predict PTA performance, and validate analytical codes that will be used to predict flow fields in which the propfan will operate.

Little, B. H., Jr.↗
NASA NTRS1987

Three-dimensional test requirement for random vibration testing

An approach to defining and evaluating three-dimensional vibration test requirements is discussed. The approach is used to develop the three-dimensional space random-vibration test requirements for missile components subjected to truck transportation environments. One-dimensional testing parameters such as power spectral density and overall g rms values for three mutually perpendicular directions represent the test requirements. The coherence characteristics between each input axis were established and adjusted empirically in an attempt to simulate the cross-correlation in three-dimensional random vibration excitation.

Chang, Kurng↗
NASA NTRS1988

The Instrument Test Dewar (ITD): Testing satellite instruments at 1.5 K

The Instrument Test Dewar (ITD) is a cryogenic facility designed and built to test Cosmic Background Explorer (COBE) satellite instruments at 1.5 K. The facility provides a high vacuum and thermal environment with payload thermal, electrical and optical interfaces. There are two concentric vacuum spaces which are not hermitically sealed. The instrument vacuum space is 81.28 cm by 243.84 cm and is cooled by an LHe shroud. The guard vacuum space surrounds an LN2 shroud. There are two separate cryosorption pumping systems and a mechanical LHe pumping system. The data acquisition systems provide payload and housekeeping data. There have been various problems with the facility, and changes and improvements have been made to assure optimum test conditions. COBE instrument testing has been completed on structural, thermal model hardware and the protoflight units.

Milam, Laura J.↗
NASA NTRS1988

Transient Pressure Test Article test program

The Transient Pressure Test Article test program being conducted at NASA-Marshall is described. The main goal of the TPTA test program is to provide data to verify the sealing capability of the redesigned SRM field joints, the nozzle-to-case joint, and the igniter joint. The TPTA test program can be used to demonstrate the assembly/disassembly and reusability of the redesigned joints along with the adequacy of assembly/disassembly tooling, procedures, and inspections.

Vibbart, Charles M.↗
NASA NTRS1989

The Space Station Photovoltaic Panels Plasma Interaction Test Program: Test plan and results

The Plasma Interaction Test performed on two space station solar array panels is addressed. This includes a discussion of the test requirements, test plan, experimental set-up, and test results. It was found that parasitic current collection was insignificant (0.3 percent of the solar array delivered power). The measured arcing threshold ranged from -210 to -457 V with respect to the plasma potential. Furthermore, the dynamic response of the panels showed the panel time constant to range between 1 and 5 microsec, and the panel capacitance to be between .01 and .02 microF.

Nahra, Henry K.↗