Search NASA⌕ Search

SEARCH · Search NASA

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

An efficient tip jet drive

A reexamination is conducted of the ideal propulsive efficiency of helicopter main rotor tipjet drives, in view of reduced tip-speed and lower jet exhaust velocity possibilities afforded by more advanced rotor designs than those contemplated in the 1950s. Relative to a hot jet-drive design, the most efficient system presently formulated inproves ideal propulsive efficiency by 62 percent, actual propulsive efficiency by 45 percent, and overall fuel efficiency by 19 percent. This vehicle, with reduced rotor speed and ibcreased rotor solidity, will result in a lighter, quieter vehicle than a turboshaft rotor-drive system, up to a gross vehicle weight of 36,400 lbs.

Phillips, James D.↗
NASA NTRS1992

Annoyance caused by aircraft en route noise

A laboratory experiment was conducted to quantify the annoyance response of people on the ground to enroute noise generated by aircraft at cruise conditions. The en route noises were ground level recordings of eight advanced turboprop aircraft flyovers and six conventional turbofan flyovers. The eight advanced turboprop enroute noises represented the NASA Propfan Test Assessment aircraft operating at different combinations of altitude, aircraft Mach number, and propeller tip speed. The conventional turbofan en route noises represented six different commercial airliners. The overall durations of the en route noises varied from approximately 40 to 160 sec. In the experiment, 32 subjects judged the annoyance of the en route noises as well as recordings of the takeoff and landing noises of each of 5 conventional turboprop and 5 conventional turbofan aircraft. Each of the noises was presented at three sound pressure levels to the subjects in an anechoic listening room. Analysis of the judgments found small differences in annoyance between three combinations of aircraft type and operation. Current tone and corrections did not significantly improve en route annoyance prediction. The optimum duration-correction magnitude for en route noise was approximately 1 dB per doubling of effective duration.

Mccurdy, David A.↗
NASA NTRS1990

Overview of NASA PTA propfan flight test program

The progress is covered of the NASA sponsored Propfan Test Assessment (PTA) flight test program. In PTA, a 9 ft. diameter propfan was installed on the left wing of a Gulfstream GII executive jet and is undergoing extensive flight testing to evaluate propfan structural integrity, near and far field noise, and cabin interior noise characteristics. This research testing includes variations in propeller tip speed and power loading, nacelle tilt angle, and aircraft Mach number and altitude. As a result, extensive parametric data will be obtained to verify and improve computer codes for predicting propfan aeroelastic, aerodynamic, and aeroacoustic characteristics. Over 600 measurements are being recorded for each of approx. 600 flight test conditions.

Graber, Edwin J.↗
NASA NTRS1991

Far-field hover acoustic characteristics of the XV-15 tiltrotor aircraft with Advanced Technology Blades

An experimental investigation has been conducted with the XV-15 tilt-rotor VTOL aircraft in order to ascertain the noise-reduction efficacy of Advanced Technology Blades (ATBs). Attention is given to acoustic directivity characteristics in the lower hemisphere of the sound field. Modest overall sound pressure levels (OASPLs) were measured near the in-plane position, showing that thickness noise is not significant in hover when ATBs are used; rotor tip-speed reductions reduced the average OASPL by nearly 8 dB in-plane and by nearly 5 dB at 12.6 deg below the rotor plane.

Conner, David A.↗
NASA NTRS1950

Performance of High-pressure-ratio Axial-flow Compressor Using Highly Cambered NACA 65-series Blower Blades at High Mach Numbers

A complete stage of an axial-flow compressor was designed and built to investigate the possibility of obtaining a high pressure ratio with an acceptable efficiency through the use of the optimum combination of high blade loading and high relative inlet Mach number. Over-all stage performance was investigated over a range of flows at equivalent tip speeds of 418 to 836 feet per second. At design speed (836 ft/sec), a peak total-pressure ration of 1.445 was obtained with an adiabatic efficiency of 0.89. For design angle of attack at the mean radius, a total-pressure ratio of 1.392 was obtained.

COMPRESSORS - AXIAL FLOW↗
NASA NTRS1951

Effect of Blade-surface Finish on Performance of a Single-stage Axial-flow Compressor

A set of modified NACA 5509-34 rotor and stator blades was investigated with rough-machine, hand-filed, and highly polished surface finishes over a range of weight flows at six equivalent tip speeds from 672 to 1092 feet per second to determine the effect of blade-surface finish on the performance of a single-stage axial-flow compressor. Surface-finish effects decreased with increasing compressor speed and with decreasing flow at a given speed. In general, finishing blade surfaces below the roughness that may be considered aerodynamically smooth on the basis of an admissible-roughness formula will have no effect on compressor performance.

COMPRESSORS - AXIAL FLOW↗
NASA NTRS1951

Some effects of blade trailing-edge thickness on performance of a single-stage axial-flow compressor

A set of modified NACA 65-series blower blades designed for axial inlet velocity, high inlet Mach number, and high blade loading was investigated for trailing-edge thickness of 0.015, 0.030, and 0.045 inch to determine the effect of trailing-edge thickness on single-stage axial-flow-compressor performance. Trailing-edge thickness effects were small except at the highest tip speed investigated (915 ft/sec). Trailing-edge thickness up to 30 percent of maximum blade thickness were used without sacrifice of performance of NACA 65-series blades.

AIRFOILS - THICKNESS↗
NASA NTRS1955

Performance of a High-solidity High-pressure-ratio Transonic Rotor

A high-solidity low-aspect-ratio transonic rotor with an inlet hub-tip ratio of 0.52 was investigated experimentally. The rotor developed a total-pressure tatio of 1.93 and an efficiency of 92 percent at an equivalent wheel tip speed of 1036 feet per second. The feasibility of using this rotor as a component of an inlet stage of an axial-flow compressor was investigated.

Neumann, Harvey E↗
NASA NTRS1928

Characteristics of Five Propellers in Flight

This investigation was made for the purpose of determining the characteristics of five full-scale propellers in flight. The equipment consisted of five propellers in conjunction with a VE-7 airplane and a Wright E-2 engine. The propellers were of the same diameter and aspect ratio. Four of them differed uniformly in thickness and pitch and the fifth propeller was identical with one of the other four with exception of a change of the airfoil section. The propeller efficiencies measured in flight are found to be consistently lower than those obtained in model tests. It is probable that this is mainly a result of the higher tip speeds used in the full-scale tests. The results show also that because of differences in propeller deflections it is difficult to obtain accurate comparisons of propeller characteristics. From this it is concluded that for accurate comparisons it is necessary to know the propeller pitch angles under actual operating conditions. (author)

Crowley, J W , Jr↗
NASA NTRS1933

Measurement of the Differential and Total Thrust and Torque of Six Full-Scale Adjustable-Pitch Propellers

Force measurements giving total thrust and torque, and propeller slip stream surveys giving differential thrust and torque were simultaneously made on each of six full-scale propellers in the 20-foot propeller-research tunnel of the National Advisory Committee for Aeronautics. They were adjustable-pitch metal propellers 9.5 feet in diameter; three had modified Clark Y blade sections and three had modified RAF-6 blade sections. This report gives the differential thrust and torque and the variation caused by changing the propeller tip speed and the pitch setting. The total thrust and torque obtained from integration of the thrust and torque distribution curves are compared with those obtained by direct force measurements.

Stickle, George W↗
NASA NTRS1936

Wind-Tunnel Tests of a 10-foot-diameter Gyroplane Rotor

This report presents the results of wind-tunnel tests on a model gyroplane rotor 10 feet in diameter. The rotor blades had zero sweepback and zero offset; the hub contained a feathering mechanism that provided control of the rotor rolling moment, but not of the pitching moment. The rotor was tested with 4 blades and with 2 blades. The entire useful range of pitch settings and tip-speed ratios was investigated including the phase of operation in which the rotor turned very slowly, or idled.

Wheatley, John B↗
NASA NTRS1937

An analysis of the factors that determine the periodic twist of an autogiro rotor blade, with a comparison of predicted and measured results

Report presents an analysis of the factors that determine the periodic twist of a rotor blade under the action of the air forces on it. The results of the analysis show that the Fourier coefficients of the twist are linear expressions involving only the tip-speed ratio, the pitch setting, the inflow coefficient, the pitching-moment coefficient of the blade airfoil section, and the physical characteristics of the rotor blade and machine. The validity of the analysis was examined by using it to predict the twist of a rotor whose twist characteristics had previously been measured in flight. The agreement between the calculated and experimental results was satisfactory.

Wheatley, John B↗
NASA NTRS1941

A simplified theoretical method of determining the characteristics of a lifting rotor in forward flight

Theoretical derived expressions for the flapping, the thrust, the torque, and the profile drag-lift ratio of nonfeathering rotor with hinged, rectangular, linearly twisted blades are given as simple functions of the inflow velocity and the blade pitch. Representative values of the coefficients of each of the terms in these expressions are tabulated for a series of specified values of the tip-speed ratio. Analysis indicates that the tabulated values can be used to calculate, with reasonable accuracy, the characteristics of any rotor of conventional design.

Bailey, F J , Jr↗
NASA NTRS1948

Full-Scale Investigation of Aerodynamic Characteristics of a Typical Single-Sotor Helicopter in Forward Flight

As part of the general helicopter research program being undertaken by the National Advisory Committee for Aeronautics to provide designers with fundamental rotor information, the forward-flight performance characteristics of a typical single-rotor helicopter, which is equipped with main and tail rotors, have been investigated in the Langley full-scale tunnel. The test conditions included operation of tip-speed ratios from 0.10 to 0.27 and at thrust coefficients from 0.0030 to 0.0060. Results obtained with production rotor were compared with those for an alternate set of blades having closer rib spacing and a smoother and more accurately contoured surface in order to evaluate the performance gains that are available by the use of rotor blades having an improved surface condition. The wind tunnel results are shown to be in fair agreement with the results of both flight tests and theoretical predictions.

Dingeldein, Richard C↗
NASA NTRS1949

Two-dimensional compressible flow in turbomachines with conic flow surfaces

A general method of analysis is developed for two-dimensional, steady, compressible flow in stators or rotors of radial and mixed flow turbomachines with conic flow surfaces (surfaces of right circular cones generated by center line of flow passage in the axial-radial plane). The variables taken into account are: (1) tip speed of the rotor, (2) flow rate, (3) blade shape, (4) variation in passage height with radius, (5) number of blades, and (6) cone angle of the flow surface. Relaxation methods are used to solve the nonlinear differential equation for the stream function. Two numerical examples are presented; one for compressible and the other for incompressible flow in a centrifugal compressor with thin, straight blades. The results of these examples are given by plots of the streamlines, constant velocity-ratio lines, and constant pressure-ratio line.

Stanitz, John D↗
NASA NTRS1949

Design and performance of family of diffusing scrolls with mixed-flow impeller and vaneless diffuser

A family of diffusing scrolls was designed for use with a mixed-flow impeller and a small-diameter vaneless diffuser. The design theory, intended to maintain a uniform pressure around the scroll inlet, permits determination of the position of scroll cross sections of preassigned area by considering the radial variation in fluid density and the effects of friction along the scroll. Inasmuch as the design method leaves the cross-sectional shape undetermined, the effect of certain variations in scroll shape was investigated by studying scrolls having angles of divergence (of the scroll walls downstream of the entrance section) of 24 degrees, 40 degrees, and 80 degrees. A second 80 degree scroll was of asymmetrical construction and a third was plaster-cast instead of sand-cast. Each scroll was tested as a compressor component at actual impeller tip speeds of 700 to 1300 feet per second from full throttle to surge.

Brown, W Byron↗
NASA NTRS1950

Two-dimensional compressible flow in centrifugal compressors with straight blades

Six numerical examples are presented for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with thin straight blades, the center lines of which generate the surface of a right circular cone when rotated about the axis of the compressor. A seventh example is presented for incompressible flow. The solutions were obtained in a region of the compressors, including the impeller tip, that was considered to be unaffected by the diffuser vanes or by the impeller-inlet configuration. Each solution applies to radial and mixed flow compressors with various cone angles but with the same angle between blades on the conic flow surface. The solution also apply to radial and mixed flow turbines with the rotation and the flow direction reversed. The effects of variations in the following parameters were investigated: (1) flow rate, (2) impeller-tip speed, (3) variation of passage height with radius, and (4) angle between blades on conic flow surface. The numerical results are presented in plots of the streamlines and constant Mach number lines. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined (in the region investigated by this analysis) for all operating conditions.

Stanitz, John D↗
NASA NTRS1952

Effects of compressibility on the performance of two full-scale helicopter rotors

Report presents the results of an investigation conducted on the Langley helicopter test tower to determine experimentally the effects of compressibility on the performance and blade pitching moments of two full-scale helicopter rotors. Two sets of rotor blades were tested which differed only in that the blades of one set incorporated -8 degrees of linear twist, whereas the blades of the other set were untwisted. The tests covered a range of tip speeds from 350 to 770 feet per second and a range of pitch angles from 0 degrees to the limit imposed by extreme vibration.

Carpenter, Paul J↗