Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Effect of an oscillating flow direction on leading edge heat transfer

An experimental investigation was conducted to examine the effect of a periodic variation in the angle of attack on heat transfer at the leading edge of a gas turbine blade. A circular cylinder was used as a large-scale model of the leading edge region. The cylinder was placed in a wind tunnel and was oscillated rotationally about its axis. The incident flow Reynolds number and the Strouhal number of oscillation were chosen to model an actual turbine condition. Incident turbulence levels up to 4.9 percent were produced by grids placed upstream of the cylinder. The transfer rate was measured using a mass transfer technique and heat transfer rates inferred from the results. A direct comparison of the unsteady and steady results indicate that the effect is dependent on the Strouhal number, turbulence level, and the turbulence length scale, but that the largest observed effect was only a 10 percent augmentation at the nominal stagnation position.

Marziale, M. L.↗
NASA NTRS1984

Length to diameter ratio and row number effects in short pin fin heat transfer

The relative effects of pin length to diameter ratio and of pin row geometry on the heat transfer from pin fins, was determined. Array averaged heat transfer coefficients on pin and endwall surfaces were measured for two configurations of staggered arrays of short pin fins (length to diameter ratio of 4). One configuration contained eight streamwise rows of pins, while the other contained only four rows. Results showed that both the 8-row and the 4-row configurations for an L sub p/D of 4, exhibit higher heat transfer than in similar tests on shorter pin fins (L sub p/D of 1/2 and 2). It was also found that for this L sub p/D ratio, the array averaged heat transfer was slightly higher with eight rows of staggered pins than with only four rows. Previously announced in STAR as N83-14431

Brigham, B. A.↗
NASA NTRS1984

Explicit guidance of drag modulated aeroassisted transfer between elliptical orbits

This paper presents the complete analysis of the problem of minimum-fuel aeroassisted transfer between coplanar elliptical orbits in the case where the orientation of the final orbit is free for selection in the optimization process. The comparison between the optimal pure propulsive transfer and the idealized aeroassisted transfer, by several passages through the atmosphere, is made. In the case where aeroassisted transfer provides fuel saving, a practical scheme for its realization by one passage is proposed. The maneuver consists of three phases: a deorbit phase for nonzero entry angle, followed by an atmospheric fly-through with variable drag control and completed by a postatmospheric phase. An explicit guidance formula for drag control is derived and it is shown that the required exit speed for ascent to the final orbit can be obtained with a very high degree of accuracy.

Vinh, N. X.↗
NASA NTRS1982

Turbine heat transfer

Objectives and approaches to research in turbine heat transfer are discussed. Generally, improvements in the method of determining the hot gas flow through the turbine passage is one area of concern, as is the cooling air flow inside the airfoil, and the methods of predicting the heat transfer rates on the hot gas side and on the coolant side of the airfoil. More specific areas of research are: (1) local hot gas recovery temperatures along the airfoil surfaces; (2) local airfoil wall temperature; (3) local hot gas side heat transfer coefficients on the airfoil surfaces; (4) local coolant side heat transfer coefficients inside the airfoils; (5) local hot gas flow velocities and secondary flows at real engine conditions; and (6) local delta strain range of the airfoil walls.

Rohde, J. E.↗
NASA NTRS1982

Coolant passage heat transfer with rotation

Although the effects of the coriolis and buoyancy forces due to rotation on coolant-side heat transfer are generally not included in the design methods for blades, the influence of these forces could be large. Comparisons of nonrotating heat transfer data and extrapolations of available correlation for the average heat transfer coefficients with radial outflow of cooling air showed that neglecting rotation at gas turbine engine conditions result in variations in the heat transfer coefficient by as much as 45 percent. This, in effect, results in blade metal temperatures running as much as 100 F different from predicted values. This also may explain why rotating blade metal temperatures in engine tests are often higher than expected from results obtained in nonrotating cascade tests.

Rohde, J. E.↗
NASA NTRS1984

Preliminary results of a study of the relationship between free stream turbulence and stagnation region heat transfer

The mechanism that causes free stream turbulence to increase heat transfer in the stagnation region of turbine vanes and blades was studied. The work is being conducted in a wind tunnel at atmospheric conditions to facilitate measurements of turbulence and heat transfer. The model size is scaled up to simulate Reynolds numbers (based on leading edge diameter) that are to be expected on a turbine blade leading edge. Reynolds numbers from 13,000 to 177,000 were run in the present tests. Spanwise averaged heat transfer measurement with high and low turbulence were made with rough and smooth surface stagnation regions. Results of these measurements show that the boundary layer remains laminar in character even in the presence of free stream turbulence at the Reynolds numbers tested. If roughness is added the boundary layer becomes transitional as evidenced by the heat transfer increase with increasing distance from the stagnation line. Hot wire measurements near the stagnation region downstream of an array of parallel wires has shown that vorticity in the form of mean velocity gradients is amplified as flow approaches the stagnation region.

Vaanfossen, G. J., Jr.↗
NASA NTRS1984

Heat transfer and pressure drop in blade cooling channels with turbulence promoters

Repeated rib roughness elements have been used in advanced turbine cooling designs to enhance the internal heat transfer. Often the ribs are perpendicular to the main flow direction so that they have an angle-of-attack of 90 deg. The objective of the project was to investigate the effect of rib angle-of-attack on the pressure drop and the average heat transfer coefficients in a square duct with two opposite rib-roughned walls for Reynolds number varied from 8000 to 80,000. The rib height-to-equivalent diameter ratio (e/D) was kept at a constant value of 0.063, the rib pitch-to-height ratio (P/e) was varied from 10 to 20, and the rib angle-of-attack (alpha) was varied from 90 deg to 60 deg to 45 deg to 30 deg respectively. Two types of entrance conditions were examined, namely, long duct and sudden contraction. The heat transfer coefficient distribution on the smooth side wall and the rough side wall at the entrance and the fully developed regions were measured. Thermal performance comparison indicated that the pumping power requirement for the rib with an oblique angle to the flow (alpha = 45 deg to 30 deg) was about 20 to 50 percent lower than the rib with a 90 deg angle to the flow for a given heat transfer duty.

Han, J. C.↗
NASA NTRS1984

Methods for heat transfer and temperature field analysis of the insulated diesel

Work done during phase 1 of a three-year program aimed at developing a comprehensive heat transfer and thermal analysis methodology oriented specifically to the design requirements of insulated diesel engines is reported. The technology developed in this program makes possible a quantitative analysis of the low heat rejection concept. The program is comprehensive in that it addresses all the heat transfer issues that are critical to the successful development of the low heat rejection diesel engine: (1) in-cylinder convective and radiative heat transfer; (2) cyclic transient heat transfer in thin solid layers at component surfaces adjacent to the combustion chamber; and (3) steady-state heat conduction in the overall engine structure. The Integral Technologies, Inc. (ITI) program is comprised of a set of integrated analytical and experimental tasks. A detailed review of the ITI program approach is provided, including the technical issues which underlie it and a summay of the methods that were developed.

Morel, T.↗
NASA NTRS1985

Primary propulsion of electrothermal, ion and chemical systems for space-based radar orbit transfer

An orbit transfer mission concept has been studied for a Space-Based Radar (SBR) where 40 kW required for radar operation is assumed available for orbit transfer propulsion. Arcjet, pulsed electrothermal (PET), ion, and storable chemical systems are considered for the primary propulsion. Transferring two SBR per shuttle flight to 1112 km/60 deg using electrical propulsion systems offers an increased payload at the expense of increased trip time, up to 2000 kg each, which may be critical for survivability. Trade offs between payload mass, transfer time, launch site, inclination, and height of parking orbits are presented.

Wang, S. Y.↗
NASA NTRS1985

Local heat-transfer measurements on a large, scale-model turbine blade airfoil using a composite of a heater element and liquid crystals

Local heat transfer coefficients were experimentally mapped along the midchord of a five-time-size turbine blade airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a mylar sheet with a layer of cholesteric liquid crystals, that change color with temperature, and a heater sheet made of a carbon-impregnated paper, that produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. The local heat transfer coefficients are presented for Reynolds numbers from 2.8 x 10 to the 5th power to 7.6 x 10 to the 5th power. Comparisons are made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code. Also, a leading edge separation bubble was revealed by thermal and flow visualization.

Hippensteele, S. A.↗
NASA NTRS1985

Chemical and thermal nonequilibrium heat transfer analysis for hypervelocity, low Reynolds number flow

Chemical and thermal nonequilibrium phenomena are studied in the stagnation region of a hypervelocity blunt body. This investigation is motivated by the need to predict the heat transfer rate to the leading edge of Aeromaneuvering Orbital Transfer Vehicles. Flight speeds of approximately 10 km/s at altitudes of approximately 80 km are considered for body radii of 1 to 50 cm. The analysis is based on continuum theory and is applicable to the viscous-layer and incipient-merged-layer rarefied-flow regimes. A two-species, two-temperature gas model is assumed. Comparisons are made with previous theories, experimental data, and results based on the thermodynamic equilibrium assumption. The equation accounting for vibrational nonequilibrium is presented and its effects on flow properties are discussed. Parameters which require further investigation are identified. Preliminary results indicate that the inclusion of vibrational relaxation has little effect on heat transfer rate for a catalytic surface. However, vibrational nonequilibrium may increase the heat transfer rate to a noncatalytic surface, depending on the degree of nonequilibrium.

Brown, K. G.↗
NASA NTRS1984

Heat transfer investigation in the junction region of circular cylinder normal to a flat plate at 90 deg location

External heat-transfer rates were measured on a flat plate in the junction region of a circular cylinder mounted normal to the plate at a location 90 deg from the stagnation point. This configuration simulates the junction of the shroud with gas-turbine vanes. Heat-transfer results are presented for laminar, transition, and turbulent boundary layers for a Mach number of 0.14 with gas temperatures of approximately 750 deg R over a flat plate at room temperature. The measurements were made in air for a unit Reynolds number, Re/cm, range of 11,000 to 58,000. Heat-transfer measurements were conducted in the 70-ft long, 4-in. diameter shock tube. A shock-wave reflection technique was used to produce a flow Mach number of 0.14. Thin-film platinum heat gages were mounted on the flat plate and along the line of the stagnation point of the cylinder to measure the local heat flux in the junction region. The experimental heat-transfer data were correlated with the laminar and turbulent boundary-layer theories for the flat plate. With the cylinder the heat fluxes on the flat plate were greatly increased in the junction region compared to the heat flux for the plate alone.

Nagamatsu, H. T.↗
NASA NTRS1985

lasants for transfer blackbody-pumped lasers

The concept of transfer blackbody-pumped lasers is outlined, recent research results concerning these lasers are presented and the search for new lasant materials for transfer blackbody-pumped lasers is expanded. There are two basic concepts for the blackbody-pumped transfer laser which are schematically drawn. The first concept is called the translational heating concept, an example being N2:CO2. Here the blackbody cavity is heated to approximately 2000 K by collected sunlight in space. An absorbing molecule would come in contact with the blackbody walls thus coming into equilibrium with the blackbody temperature. An alternative concept shown is called the vibrational heating transfer laser. Here the absorbing molecule is not translationally heated. Energy is coupled to the molecule only by optical absorption creating a high density of vibrational states. Thus the gas temperature is near room temperature whereas the vibrational temperature comes into equilibrium with the blackbody temperature.

Deyoung, R. J.↗
NASA NTRS1985

Energy transfer mechanisms between molecules

Reliable rate coefficients for energy transfer and relaxation phenomena are needed in order to do the theoretical modeling which is necessary for accomplishing the following objectives: understanding and justifying proposed laser systems, determining limitations, identifying control parameters, and scaling to space-power requirements. Modeling also establishes the criteria to be followed for lasant selection. Lack of knowledge of rate coefficients is invariably the biggest obstacle to successful modeling. Existing theoretical methods are discussed, sources of error are identified, and transfer laser criteria suggested by the theory are listed. The emphasis is on vibrational-vibrational (V-V) energy transfer caused by both short range and long range interactions between molecules. Special attention is given to the importance of near-resonant collisional and dipole-dipole transfer. A technique is proposed for significantly improving the theoretical predictions of rate coefficients.

Meador, W. E.↗
NASA NTRS1985

Report from the Transfer-Laser Working Group

Light absorbing molecules and lasing molecules were discussed with regard to satisfying the following criteria for blackbody transfer lasers: (1) Good absorbers of blackbody radiation at 1500-2000 K; (2) Near resonant energy transfer from the absorbing gas to the lasant, provided not too many quantum number changes are required; (3) Dipole-dipole interactions for most efficient energy transfer; (4) Exothermic forward transfer reaction; (5) Polyatomic lasant molecules with at least two fundamental vibrational modes to ensure one or more states between the upper laser level and the ground state; (6) Polyatomic lasant molecules should not be so large or so complex that fast V-V relaxation occurs; (7) Metastable upper laser level for maintaining inversion, at least with respect to radiative and V-V decay; (8) Fast V-V into the upper laser level and out of the lower laser level; and (9) Lasing wavelengths less than 10.6 microns. Possible combinations of absorbers and lasants satisfying these criteria were discussed.

Meador, W. E.↗
NASA NTRS1985

Methods for heat transfer and temperature field analysis of the insulated diesel phase 2 progress report

This report describes work done during Phase 2 of a 3 year program aimed at developing a comprehensive heat transfer and thermal analysis methodology for design analysis of insulated diesel engines. The overall program addresses all the key heat transfer issues: (1) spatially and time-resolved convective and radiative in-cylinder heat transfer, (2) steady-state conduction in the overall structure, and (3) cyclical and load/speed temperature transients in the engine structure. During Phase 2, radiation heat transfer model was developed, which accounts for soot formation and burn up. A methodology was developed for carrying out the multi-dimensional finite-element heat conduction calculations within the framework of thermodynamic cycle codes. Studies were carried out using the integrated methodology to address key issues in low heat rejection engines. A wide ranging design analysis matrix was covered, including a variety of insulation strategies, recovery devices and base engine configurations. A single cylinder Cummins engine was installed at Purdue University, and it was brought to a full operational status. The development of instrumentation was continued, concentrating on radiation heat flux detector, total heat flux probe, and accurate pressure-crank angle data acquisition.

Morel, T.↗
NASA NTRS1986

Transfer function analysis of thermospheric perturbations

Applying perturbation theory, a spectral model in terms of vectors spherical harmonics (Legendre polynomials) is used to describe the short term thermospheric perturbations originating in the auroral regions. The source may be Joule heating, particle precipitation or ExB ion drift-momentum coupling. A multiconstituent atmosphere is considered, allowing for the collisional momentum exchange between species including Ar, O2, N2, O, He and H. The coupled equations of energy, mass and momentum conservation are solved simultaneously for the major species N2 and O. Applying homogeneous boundary conditions, the integration is carred out from the Earth's surface up to 700 km. In the analysis, the spherical harmonics are treated as eigenfunctions, assuming that the Earth's rotation (and prevailing circulation) do not significantly affect perturbations with periods which are typically much less than one day. Under these simplifying assumptions, and given a particular source distribution in the vertical, a two dimensional transfer function is constructed to describe the three dimensional response of the atmosphere. In the order of increasing horizontal wave numbers (order of polynomials), this transfer function reveals five components. To compile the transfer function, the numerical computations are very time consuming (about 100 hours on a VAX for one particular vertical source distribution). However, given the transfer function, the atmospheric response in space and time (using Fourier integral representation) can be constructed with a few seconds of a central processing unit. This model is applied in a case study of wind and temperature measurements on the Dynamics Explorer B, which show features characteristic of a ringlike excitation source in the auroral oval. The data can be interpreted as gravity waves which are focused (and amplified) in the polar region and then are reflected to propagate toward lower latitudes.

Mayr, H. G.↗
NASA NTRS1986

Convective heat transfer from circular cylinders located within perforated cylindrical shrouds

The influence of perforated cylindrical shrouds on the convective heat transfer to circular cylinders in transverse flow has been studied experimentally. Geometries studied were similar to those used in industrial platinum resistance thermometers. The influence of Reynolds number, ventilation factor (ratio of the open area to the total surface area of shroud), radius ratio (ratio of shroud's inside radius to bare cylinder's radius), and shroud orientation with respect to flow were studied. The experiments showed that perforated shrouds with ventilation factors in the range 0.1 to 0.4 and radius ratios in the range 1.1 to 2.1 could enhance the convective heat transfer to bare cylinders up to 50%. The maximum enhancement occurred for a radius ratio of 1.4 and ventilation factors between 0.2 and 0.3. It was found that shroud orientation influenced the heat transfer, with maximum heat transfer generally occurring when the shroud's holes were centered on either side of the stagnation line. However, the hole orientation effect is of second order compared to the influence of ventilation factor and radius ratio.

Daryabeigi, K.↗