Search NASA⌕ Search

SEARCH · Search NASA

Results for “Volatile analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Self-Supplied Liquid Injection Field Desorption/Ionization Ion Source for an Orthogonal Time-of-Flight Instrument

A new implementation of a dedicated ion source for field ionization (FI), field desorption (FD), and liquid injection field desorption/ionization (LIFDI) for the JEOL AccuTOF GC series of orthogonal-acceleration time-of-flight instruments is presented. In contrast to existing implementations, this third-party LIFDI probe and source combination does not require the exchange of the entire ion source comprising ion source block and lens stack to switch from electron ionization (EI) to LIFDI. Rather, the methods may be swapped conveniently by only exchanging the ion source block for a mechanical probe guide and inserting the LIFDI probe in place of the standard direct insertion probe (DIP) via the vacuum lock. Further, this LIFDI setup does not require any changes of the electronics or software of the AccuTOF mass spectrometer because it is self-supplied in terms of power supply, observation optics, and computer control. The setup offers advanced FI/FD/LIFDI control features such as emission-controlled emitter heating current and emitter flash baking during elongated runs as required for gas chromatography-FI-mass spectrometry (MS). The LIFDI source and probe and its operation are reported in detail. FI spectra of the volatile analytes toluene, heptane, and pentafluoroiodobenzene are presented. LIFDI operation is demonstrated for the analysis of the saturated hydrocarbon dotriacontane and the low-mass hydrocarbon polymers polystyrene 484 and polystyrene 1050. Further, the air-sensitive 2nd-generation Hoveyda–Grubbs catalyst is analyzed by LIFDI-MS. For comparison with long-established LIFDI instrumentation, some of the spectra obtained with the new setup are also compared with those from a double-focusing magnetic sector instrument. .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Ambient Gas-Particle Partitioning of Tracers for Biogenic Oxidation

Exchange of atmospheric organic compounds between gas and particle phases is important in the production and chemistry of particle-phase mass but is poorly understood due to a lack of simultaneous measurements in both phases of individual compounds. Measurements of particle- and gas phase organic compounds are reported here for the southeastern United States and central Amazonia. Polyols formed from isoprene oxidation contribute 8% and 15% on average to particle-phase organic mass at these sites but are also observed to have substantial gas-phase concentrations contrary to many models that treat these compounds as nonvolatile. The results of the present study show that the gas-particle partitioning of approximately 100 known and newly observed oxidation products is not well explained by environmental factors (e.g., temperature). Compounds having high vapor pressures have higher particle fractions than expected from absorptive equilibrium partitioning models. These observations support the conclusion that many commonly measured biogenic oxidation products may be bound in low-volatility mass (e.g., accretion products, inorganic organic adducts) that decomposes to individual compounds on analysis. However, the nature and extent of any such bonding remains uncertain. Similar conclusions are reach for both study locations, and average particle fractions for a given compound are consistent within similar to 25% across measurement sites.

Environmental Molecular Sciences Laboratory↗

Embedded Electronic Nose for VOC Mixture Analysis

This paper details the work done towards a low cost, small size, portable embedded electronic nose (e-nose) and its application for analysis of different VOC mixtures. The sensor array is composed of commercially available metal oxide semiconductor sensors by Figaro. The embedded E-nose consists of an ADuC831 and has an RS 232 interface for Desktop PC for higher level data collection and NN training. The ESP tool with database facility and multilayer perceptron neural network (MLP NN) is employed to interface the embedded hardware and to process the electronic nose signals before being classified. The use of embedded e-nose for the quantification of VOCs in mixtures is investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Integration of wholesale and retail electricity markets: Modeling and stability analysis

The main contribution of this report is to develop a theoretical model of the interaction between retail and wholesale markets and to analyze properties of this dynamical model. The behavior by the flexible loads, when combined with interaction of the retail market with the wholesale market, creates a dynamical system. It is then of interest to understand the behavior of this dynamical system. This analysis will be useful in determining the impact of the market architecture on price volatility, generator dispatch, congestion in the transmission system, etc.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Generating Novel Aroma Phenotypes Using Commercial Wine Samples to Characterize an F1 Population

Due to their disease tolerance and cold hardy nature, interspecific hybrid grapes are widely grown in the Midwestern and Northeastern United States, with additional interest worldwide in the face of increased abiotic and biotic stresses from climate change. However, the aroma profile of these hybrids is unique and generally less popular in comparison with Vitis vinifera grapes. One of the challenges in any phenotyping project is first defining the traits of interest. As wine quality was our ultimate metric of interest, the aroma profile of commercial wines produced from the parents of a breeding population ( Vitis aestivalis derived ‘Norton’ x V. vinifera . ‘Cabernet Sauvignon’) was first assessed for traits of interest. We investigated 11 commercial wines each of Norton, a popular hybrid in Missouri and Cabernet Sauvignon (Cab) for their volatile profiles using the more inclusive metabolomics-based workflow. We then analyzed 21 Norton and 21 Cab grapes from different sites and vintages for the free and bound volatile compounds using HS-SPME-GCMS to validate the differences in wine. The GCMS data was processed using XCMS software to find features that were different between the two cultivars. The two cultivars were found to have differences in their volatile profiles, with 304 features different for wine volatiles, 418 features different for free volatiles, and 302 features different for bound volatiles at 0.05 significance level and with at least a 1.5-fold change between the two cultivars. Those features were used to identify several odor-active compounds in both grapes and wines, including β-damascenone, β-ionone, eugenol, 1,1,6-trimethyl-1,2-dihydronaphthalene (TDN), and methyl salicylate. Some of the identified compounds were higher in Norton than Cab; however, several features were higher in Cab. Using the identified aroma compounds as markers, we phenotyped an F1 population of Norton and Cab. The F1 population was found to be segregating for many aroma compounds with some genotypes demonstrating an even higher concentration of aroma volatiles than either of the parents. Ultimately, using commercially available samples paired with untargeted analysis proved to be an efficient way to determine phenotypes of interest for further analysis and may offer an easy way to choose potential parents with desired traits for breeding.

59 BASIC BIOLOGICAL SCIENCES↗

Thermochemical characterization of some thermoplastic materials

The thermochemical and flammability characteristics of some typical thermoplastic materials currently in use or being considered for use in aircraft interiors are described. The properties studied included thermomechanical properties such as glass-transition and melt temperature, changes in polymer enthalpy, thermogravimetric analysis in anerobic and oxidative environments, oxygen index, smoke evolution, relative toxicity of the volatile products of pyrolysis, and selected physical properties. The generic polymers evaluated included acrylonitrile butadiene styrene, bisphenol A polycarbonate, 9,9 bis (4-hydroxyphenyl) fluorene polycarbonate-poly (dimethylsiloxane) block polymer, phenolphthalein-bisphenol A polycarbonate, phenolphthalein polycarbonate, polyether sulfone, polyphenylene oxide, polyphenylene sulfide, polyaryl sulfone, chlorinated polyvinyl chloride homopolymer, polyvinyl fluoride, and polyvinylidene fluoride. Processing parameters, including molding characteristics of some of the advanced polymers, are described. Test results and relative rankings of some of the flammability, smoke, and toxicity properties are presented. Under these test conditions, some of the advanced polymers evaluated were significantly less flammable and toxic than or equivalent to polymers in current use.

Kourtides, D. A.↗

Extracting trace substances from biological fluids

Apparatus is used as aid in extraction of trace amounts of volatile organics from biological fluids. "Transervaporator" makes it possible to prepare violate fraction for analysis by high-resolution gas chromatography.

Zlatkis, A.↗

Depth/diameter relationships of fresh craters within Hesperia Planum, Mars

Meteorite impact craters represent important geological features for revealing the near-surface layers of a planetary surface. In the case of Mars, this characteristic was proposed as a useful method to study spatial variations of such attributes as the distribution of sub-surface volatiles, and heat flow. Using the Planetary Image Cartography System (PICS) software, a quantitative analysis was completed of the geometry of fresh impact craters in the Hesperia Planum region of Mars, where an uniform target material and optimum viewing geometry make possible an analysis of target effects over a large geographic region. Because of the morphologic similarity to the lunar maria, it is likely that Hesperia Planum comprises a series of flood lavas that partially infilled topographic depressions within the Martian highlands. Measurements of partially buried crater rims suggest that the lava flows within Hesperia Planum are between 200-400 m thick.

Mouginis-Mark, P. J.↗

Geochemistry of HASP, VLT, and other glasses from double drive tube 79001/2

The Apollo 17 double drive tube 79001/2 (station 9, Van Serg Crater) is distinctive because of its extreme maturity, abundance, and variety of glass clasts. It contains mare glasses of both high Ti and very low Ti (VLT) compositions, and highland glasses of all compositions common in lunar regolith samples: highland basalt (feldspathic; Al2O3 greater than 23 wt percent), KREEP (Al2O3 less than 23 wt percent, K2O greater than 0.25 wt percent), and low-K Fra Mauro (LKFM; Al2O3 less than 23 wt percent, K2O less than 0.25 wt percent). It also contains rare specimens of high-alumina, silica-poor (HASP), and ultra Mg glasses. HASP glasses contain insufficient SiO2 to permit the calculation of a standard norm, and are thought to be the product of volatilization during impact melting. They have been studied by electron microprobe major-element analysis techniques but have not previously been analyzed for trace elements. The samples analyzed for this study were polished grain mounts of the 90-160 micron fraction of four sieved samples from the 79001/2 core (depth range 2.3-11.5 cm). A total of 80 glasses were analyzed by SEM/EDS and electron microprobe, and a subset of 33 of the glasses, representing a wide range of compositional types, was chosen for high-sensitivity INAA. A microdrilling device removed disks (mostly 50-100 micron diameter, weighing approx. 0.1-0.5 micro-g) for INAA. Preliminary data reported here are based only on short counts done within two weeks of irradiation.

Lindstrom, D. J.↗

Electronic Model of a Ferroelectric Field Effect Transistor

A pair of electronic models has been developed of a Ferroelectric Field Effect transistor. These models can be used in standard electrical circuit simulation programs to simulate the main characteristics of the FFET. The models use the Schmitt trigger circuit as a basis for their design. One model uses bipolar junction transistors and one uses MOSFET's. Each model has the main characteristics of the FFET, which are the current hysterisis with different gate voltages and decay of the drain current when the gate voltage is off. The drain current from each model has similar values to an actual FFET that was measured experimentally. T'he input and o Output resistance in the models are also similar to that of the FFET. The models are valid for all frequencies below RF levels. No attempt was made to model the high frequency characteristics of the FFET. Each model can be used to design circuits using FFET's with standard electrical simulation packages. These circuits can be used in designing non-volatile memory circuits and logic circuits and is compatible with all SPICE based circuit analysis programs. The models consist of only standard electrical components, such as BJT's, MOSFET's, diodes, resistors, and capacitors. Each model is compared to the experimental data measured from an actual FFET.

MacLeod, Todd C.↗

Simulation Model of A Ferroelectric Field Effect Transistor

An electronic simulation model has been developed of a ferroelectric field effect transistor (FFET). This model can be used in standard electrical circuit simulation programs to simulate the main characteristics of the FFET. The model uses a previously developed algorithm that incorporates partial polarization as a basis for the design. The model has the main characteristics of the FFET, which are the current hysterisis with different gate voltages and decay of the drain current when the gate voltage is off. The drain current has values matching actual FFET's, which were measured experimentally. The input and output resistance in the model is similar to that of the FFET. The model is valid for all frequencies below RF levels. A variety of different ferroelectric material characteristics can be modeled. The model can be used to design circuits using FFET'S with standard electrical simulation packages. The circuit can be used in designing non-volatile memory circuits and logic circuits and is compatible with all SPICE based circuit analysis programs. The model is a drop in library that integrates seamlessly into a SPICE simulation. A comparison is made between the model and experimental data measured from an actual FFET.

MacLeod, Todd C.↗

Oxidation of High-temperature Alloy Wires in Dry Oxygen and Water Vapor

Small diameter wires (150 to 250 microns) of the high temperature alloys Haynes 188, Haynes 230, Haynes 230, Haynes 214, Kanthal Al and PM2000 were oxidized at 1204 C in dry oxygen or 50% H2O /50% O2 for 70 Hours. The oxidation kinetics were monitored using a thermogravimetric technique. Oxide phase composition and morphology of the oxidized wires were determined by X-ray diffraction,field emission scanning electron microscopy, and energy dispersive spectroscopy. The alumina-forming alloys, Kanthal Al and PM2000, out-performed the chromia-forming alloys under this conditions. PM2000 was recommended as the most promising candidate for advanced hybrid seal applications for space reentry control surface seals or hypersonic propulsion system seals. This study also demonstrated that thermogravimetric analysis of small diameter wires is a powerful technique for the study of oxide volatility, oxide adherence, and breakaway oxidation.

Opila, Elizabeth J.↗

Selection of Environmentally Friendly Solvents for the Extravehicular Mobility Unit Secondary Oxygen Pack Cold Trap Testing

Freon-113(TradeMark) has been used as a chemistry lab sampling solvent at NASA/JSC for EMU (extravehicular Mobility Unit) SOP (Secondary Oxygen Pack) oxygen testing Cold Traps utilized at the USA (United Space Alliance) Houston facility. Similar testing has occurred at the HSWL (Hamilton Sundstrand Windsor Locks) facility. A NASA Executive Order bans the procurement of all ODS (ozone depleting substances), including Freon-113 by the end of 2009. In order to comply with NASA direction, HSWL began evaluating viable solvents to replace Freon-113 . The study and testing effort to find Freon-113 replacements used for Cold Trap sampling is the subject of this paper. Test results have shown HFE-7100 (a 3M fluorinated ether) to be an adequate replacement for Freon-113 as a solvent to remove and measure the non-volatile residue collected in a Cold Trap during oxygen testing. Furthermore, S-316 (a Horiba Instruments Inc. high molecular weight, non-ODS chlorofluorocarbon) was found to be an adequate replacement for Freon-113 as a solvent to reconstitute non-volatile residue removed from a Cold Trap during oxygen testing for subsequent HC (hydrocarbon) analysis via FTIR (Fourier Transform Infrared Spectroscopy).

Steele, John↗

The Sample Analysis at Mars Investigation and Instrument Suite

The Sample Analysis at Mars (SAM) investigation of the Mars Science Laboratory(MSL) addresses the chemical and isotopic composition of the atmosphere and volatilesextracted from solid samples. The SAM investigation is designed to contribute substantiallyto the mission goal of quantitatively assessing the habitability of Mars as an essentialstep in the search for past or present life on Mars. SAM is a 40 kg instrument suite locatedin the interior of MSLs Curiosity rover. The SAM instruments are a quadrupole massspectrometer, a tunable laser spectrometer, and a 6-column gas chromatograph all coupledthrough solid and gas processing systems to provide complementary information on thesame samples. The SAM suite is able to measure a suite of light isotopes and to analyzevolatiles directly from the atmosphere or thermally released from solid samples. In additionto measurements of simple inorganic compounds and noble gases SAM will conducta sensitive search for organic compounds with either thermal or chemical extraction fromsieved samples delivered by the sample processing system on the Curiosity rovers roboticarm.

isotopes↗

The CAESAR New Frontiers Comet Sample Return Mission

The Comet Astrobiology Exploration Sample Return (CAESAR) mission is one of two finalists selected by NASA for Phase A study in the New Frontiers program. CAESAR will acquire a minimum of 80 grams of material from the surface of comet 67P/Churuyumov-Gerasimenko and return it to Earth for laboratory analysis. CAESAR preserves much of the science of a cryogenic sample return by retaining volatiles in a dedicated reservoir securely separated from the solid sample. Comet 67P was selected based on its favorable orbital geometry and the risk reduction and scientific context provided by the ESA (European Space Agency)'s Rosetta mission. CAESAR's objectives are to understand the origins of the Solar System starting materials and how these components came together to form planets and give rise to life. We also seek to resolve the conflicting views of comet origins arising from the Stardust and Rosetta missions. While the greater than 1 micron solids returned by Stardust originated in the hot, inner solar nebula, measurements by Rosetta suggest 67P volatiles formed at cryogenic temperatures and remained unchanged for billions of years. This dichotomy provides the rationale for returning both solid and gaseous samples.

CAESAR New Frontiers↗

TESS and HARPS reveal two sub-Neptunes around TOI 1062

The Transiting Exoplanet Survey Satellite (TESS) mission was designed to perform an all-sky search of planets around bright and nearby stars. Here we report the discovery of two sub-Neptunes orbiting around TOI 1062 (TIC 299799658), a V = 10.25 G9V star observed in the TESS Sectors 1, 13, 27, and 28. We use precise radial velocity observations from HARPS to confirm and characterize these two planets. TOI 1062b has a radius of 2.265(-0.091,+0.096) Rꚛ, a mass of 10.15 ± 0.8 Mꚛ, and an orbital period of 4.1130 ± 0.0015 days. The second planet is not transiting, has a minimum mass of 9.78(−1.18,+1.26) Mꚛ and is near the 2:1 mean motion resonance with the innermost planet with an orbital period of 7.972(−0.024,+0.018) days. We performed a dynamical analysis to explore the proximity of the system to this resonance, and to attempt further constraining the orbital parameters. The transiting planet has a mean density of 4.85(−0.74,+0.84) g/cu. cm and an analysis of its internal structure reveals that it is expected to have a small volatile envelope accounting for 0.35% of the mass at most. The star’s brightness and the proximity of the inner planet to what is know as the radius gap make it an interesting candidate for transmission spectroscopy, which could further constrain the composition and internal structure of TOI 1062b.

J. F. Otegi↗

Kinetics of Separations of Volatile Fluorides from Used Fuel Using NF3

The study of the fluorination of UO2 with various fluorinating agents using thermogravimetric analysis (TGA) is well documented. Additional research has examined the fluorination of other metals and metal oxides. Seeing the possible benefit of using analogous fluorination technologies to affect separations in used nuclear fuel, we have expanded the existing research to an investigation of the reaction of NF3 with UO2 and NpO2. The conversion fractions gathered from experimental results have been compared with those predicted by existing models for various rate-limiting phenomena.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comparison of volatiles evolving from selected highland and mare lunar regolith simulants during vacuum sintering

Volatiles evolving from JSC-1A, NU-LHT-4M and CSM-LHT-1G lunar regolith simulants during in vacuo thermal processing were analyzed using mass spectrometry as a function of temperature. Two high-fidelity simulants, JSC-1A (mare) and NU-LHT-4M (highland), were compared to a newly developed CSM-LHT-1G highland simulant, modified to closely match lunar geochemistry. Large autogenous gas loads were observed for all investigated materials. Mineralogical knowledge was used to identify and attribute individual volatile species to reacting, transforming, or decomposing constituents (hydrates, carbonates, sulfates, sulfides, clays, etc.) of the respective regolith simulant in the self-generated gas environment. Cumulative mass losses for individual simulant components as a function of temperature were quantified using mass spectrometry in conjunction with thermogravimetric analysis. Investigation of the four components of CSM-LHT-1G – anorthosite, basalt, augite, and glass – aided the attribution of volatile species to specific compounds and their respective sources. The results showed significant decomposition of non-lunar phases present in the man-made regolith simulants below the typical glass crystallization temperatures, which paves the way to devising methods for enhancing the fidelity of the simulants. Finally, high gas loads and corrosive gases (HF and HCl) were recognized as potential hazards, pertaining to the development of large testbed facilities.

42 ENGINEERING↗