Search NASA⌕ Search

SEARCH · Search NASA

Results for “WIND EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Wind-tunnel studies of the effects of stimulated damage on the aerodynamic characteristics of airplanes and missiles

As an aid in assessing the aerodynamic effects of battle damage that might be sustained by military airplanes or missiles, several wind tunnel investigations were performed at the Langley Research Center in which damage was simulated with models by the removal of all or parts of the wing and tails. Results of the investigations indicate that the loss of a major part of the vertical tail will probably result in the loss of an airplane in any speed range. The loss of major parts of the horizontal tail generally results in catastrophic instability in the subsonic range but, at low supersonic speeds, and for some planform configurations at subsonic speeds, may allow stable flight to the extent that the airplane might return to friendly territory before the pilot must eject. The results further indicate that major damage to the wing, up to the point of the complete removal of one wing panel, and major damage to the horizontal tail may be sustained without necessarily causing the loss of the airplane or pilot.

Spearman, M. L.↗
NASA NTRS1979

The effect of erosion on the solar wind stand-off distance at Mercury

Measurements of the effect of dayside magnetic reconnection on the position of the earth's forward magnetopause have been scaled to Mercury in order to predict the mean solar wind stand-off distance for average conditions of solar wind dynamic pressure. It is found that for a significant portion of the time Mercury's magnetopause will be eroded and/or compressed to within 0.2 Mercury radii of the planet's surface. Solar wind stand-off distances and solar wind dynamic pressures are also calculated for the two Mariner 10 encounters with Mercury's magnetosphere. Values of the solar wind stand-off distance range from 1.3 to 2.1 Mercury radii.

Slavin, J. A.↗
NASA NTRS1993

Wind persistence from 2-18 km using a wind profiler

Existing techniques for quantifying the effects of temporal wind variability on launch vehicles employ very limited sets of wind profile pairs derived from rising balloons. Variability due to spatial differences between the drifting balloon and a vehicle trajectory are traditionally ignored. The authors developed a technique to extract high quality wind profiles at frequent time intervals from a Doppler Radar Wind Profiler. This technique was applied to a limited number of data sets gathered from December 1990 through March 1992 at the Kennedy Space Center using the NASA 50 Mhz Wind Profiler. The authors then used these derived wind profiles to demonstrate techniques for quantifying the effects of temporal and spatial variability.

Wilfong, Timothy L.↗
NASA NTRS1994

Response of a two-dimensional dual-Doppler radar wind synthesis

The wind field resulting from a two-dimensional dual-Doppler synthesis algorithms is spectrally modified from the true wind field. The effects of spatial filtering on wind fields from the processes of interpolation, the averaging of pulses, and the effect of the finite radar pulse dimension were assessed. The effect resulting from the use of different interpolation techniques was also evaluated. Of those techniques tested, the best are the Cressman distance-weighted averaging and linear distance-weighted averaging, with the closest neighbor and uniform weighting having more undesirable characteristics. The optimum influence radius is defined as the influence radius at which the ratio of the rms difference between the Fourier and least-squares responses (a measure of the aliasing) and the variance of the filtered wind field is minimized. This seeks to minimize the effect of energy aliased into scales other than the input wavelength. For the Cressman interpolation technique, the optimum influence radius is between 1.85 and 2.25 times the maximum data spacing. The range of acceptable influence radii includes consideration of the filtering by the radar of the data as it is collected, as well as the resolution of the final dataset. The optimum influence radius is dependent upon the largest data separation in the analysis domain. The absolute optimum influence radius is not significantly affected by inclusion of the radar-beam filtering effects.

Given, Terence↗
NASA NTRS1984

The influence of a wind tunnel on helicopter rotational noise: Formulation of analysis

An analytical model is discussed that can be used to examine the effects of wind tunnel walls on helicopter rotational noise. A complete physical model of an acoustic source in a wind tunnel is described and a simplified version is then developed. This simplified model retains the important physical processes involved, yet it is more amenable to analysis. The simplified physical model is then modeled as a mathematical problem. An inhomogeneous partial differential equation with mixed boundary conditions is set up and then transformed into an integral equation. Details of generating a suitable Green's function and integral equation are included and the equation is discussed and also given for a two-dimensional case.

Mosher, M.↗
NASA NTRS1974

Development and modification of a digital program for final approach to landing

The development and implementation of a dynamic digital computer simulator which may be used to evaluate aircraft performance when operating under the control and guidance of various navigation, landing, and flight control systems are discussed. The digital computer program may be used to simulate and evaluate the relationships and interactions between various factors such as the microwave landing system, avionics receivers and onboard processors, aircraft aerodynamics, aircraft automatic control systems, control surfaces, and wind and other external effects. The models used to represent aircraft aerodynamics, control system and control surfaces; weather and wind effects; and the microwave landing system are described. Example results are presented for a simulation of a Boeing 737 using two sample control systems while subjected to various atmospheric conditions and microwave landing system errors. The limitations and performance capabilities of these control systems are discussed in terms of their ability to utilize the microwave landing system signal.

Duff, W. G.↗
NASA NTRS1978

Propulsion-airframe interactions predictability

An illustration of the possible magnitude of the transonic performance prediction problem is shown. These results derived from a careful and systematic set of tests run on a jet effects model, an aerodynamic and force model, and a pressure model, evaluated test techniques and wind tunnel effects. The results were then carefully compared with flight test data where significant discrepancies in zero-lift drag were observed. A vigorous review of the test techniques identified a number of potential error sources. Some of these were thought to be aircraft roughness and protuberances, tunnel anomalies, sting/model support corrections, and hot gas effects. In addition, there were questions on model metric splitline location and magnitude of corrections for scale and Reynolds number. Flight test inlet/engine characteristics were thought to differ, also, from those of the calibration settings in the ground facilities.

Smith, R. H.↗
NASA NTRS1978

An interpretation of Mariner 10 helium /584 A/ and hydrogen /1216 A/ interplanetary emission observations

Measurements of the interplanetary emissions of both He(584 A) and H(1216 A) on January 28, 1974, a time of solar minimum, are reported and discussed. An analysis of the Mariner 10 ultraviolet spectrometer data shows that a simultaneous measurement of both emissions results in a self-consistent determination of the physical properties of the interstellar wind. With the aid of a model the number densities of helium and hydrogen outside the solar system were found to be 0.008 + or - 0.003/cu cm and 0.04 (+0.03, -0.02)/cu cm, respectively, which indicates a He/H ratio of 0.20 (+0.30, -0.13). Values characterizing the helium cone, interstellar wind temperature, effective lifetime of hydrogen atoms in the solar system, and downstream direction of the interstellar wind are presented.

Ajello, J. M.↗
NASA NTRS2021

Wind suppression by X-rays in Cygnus X-3

Context: The radiatively driven wind of the primary star in wind-fed X-ray binaries can be suppressed by the X-ray irradiation of the compact secondary star. This causes feedback between the wind and the X-ray luminosity of the compact star. Aims: We aim to estimate how the wind velocity on the face-on side of the donor star depends on the spectral state of the high-mass X-ray binary Cygnus X-3. Methods: We modeled the supersonic part of the wind by computing the line force (force multiplier) with the Castor, Abbott & Klein formalism and XSTAR physics and by solving the mass conservation and momentum balance equations. We computed the line force locally in the wind considering the radiation fields from both the donor and the compact star in each spectral state. We solved the wind equations at different orbital angles from the line joining the stars and took the effect of wind clumping into account. Wind-induced accretion luminosities were estimated using the Bondi-Hoyle-Lyttleton formalism and computed wind velocities at the compact star. We compared them to those obtained from observations. Results: We found that the ionization potentials of the ions contributing the most to the line force fall in the extreme-UV region(100–230 Å). If the flux in this region is high, the line force is weak, and consequently, the wind velocity is low. We found a correlation between the luminosities estimated from the observations for each spectral state of Cyg X-3 and the computed accretion luminosities assuming moderate wind clumping and a low mass of the compact star. For high wind clumping, this correlation disappears. We compared the XSTAR method used here with the comoving frame method and found that they agree reasonably well with each other. Conclusions. We show that soft X-rays in the extreme-UV region from the compact star penetrate the wind from the donor star and diminish the line force and consequently the wind velocity on the face-on side. This increases the computed accretion luminosities qualitatively in a similar manner as observed in the spectral evolution of Cyg X-3 for a moderate clumping volume filling factor and a compact star mass of a few (2–3) solar masses.

O. Vilhu↗
DOE OSTI2024

Agrivoltaic Racking Design Optimization Based on Wind and Snow Loading Finite Element Analysis

The racking structure of photovoltaic (PV) systems plays a critical role in ensuring the PV panels generate power properly as it provides integral structural support and sometimes even solar tracking ability. Distinct applications of PV systems require variations of racking structure designs, which yield different mechanical performances under external loading conditions from the environment, such as heavy wind and snow. Past works, such as Reddy et al. [1], have analyzed the pressure effects of wind and snow loading on the racking structure of conventional rooftop and utility PV systems, but there is little knowledge of how various agrivoltaic racking systems perform, in terms of stress and strain, under the same loading conditions. There is also a knowledge gap in the industry on a set of optimized agrivoltaic racking design standards. This study investigates the mechanical performance of various existing racking systems and proposes novel designs that are optimized for agrivoltaics applications under wind and snow loading.

Liao, Quanhuan↗
NASA NTRS1996

Investigation of Condensation/Clustering Effects on Rayleigh Scattering Measurements in a Hypersonic Wind Tunnel

Rayleigh scattering, a nonintrusive measurement technique for the measurement of density in a hypersonic wind tunnel, is under investigation at Wright Laboratory's Mach 6 wind tunnel. Several adverse effects, i.e., extraneous scatter off walls and windows, hinder Rayleigh scattering measurements. Condensation and clustering of flow constituents also present formidable obstacles. Overcoming some of these difficulties, measurements have been achieved while the Mach 6 test section was pumped down to a vacuum, as well as for actual tunnel operation for various stagnation pressures at fixed stagnation temperatures. Stagnation pressures ranged from 0.69 MPa to 6.9 MPa at fixed stagnation temperatures of 511, 556, and 611 K. Rayleigh scatter results show signal levels much higher than expected for molecular scattering in the wind tunnel. Even with higher than expected signals, scattering measurements have been made in the flowfield of an 8-degree half-angle blunt nose cone with a nose radius of 1.5 cm.

Tyler, Charles↗
NASA NTRS1986

Low-speed wind-tunnel investigation of the effect of strakes and nose machines on lateral-directional stability of a fighter configuration

A series of low-speed static wind-tunnel force tests were conducted on a 0.15-scale model of a modern high-performance fighter aircraft. The tests identified the use of nose chines to enhance stability at high angles of attack. Results of this investigation showed that the strake was the major contributor to directional instability. The destabilizing forces were created by two mechanisms: (1) adverse flow in the region of the vertical tail, and (2) forces generated on the fuselage ahead of the center of gravity. Properly designed nose chines effectively negated the adverse flow near the vertical tail and created stabilizing forces on the forebody in the range of the stall angle of attack.

Brandon, J. M.↗
NASA NTRS1976

Wind-Tunnel Investigation of the Effect of Porous Spoilers on the Wake of a Subsonic Transport Model

Tests were conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel to determine how porosity of wing spoilers on a B-747 airplane would affect the rolling moments imposed on an aircraft following in the wake. It was found that spoilers with 40 percent porosity and hole diameter to thickness ratio of 1.1 were just as effective in reducing the rolling moment imposed on the follower as solid spoilers, for the case of two spoilers per wing panel (6.4 percent semispan each) with a following model whose span was 20 percent of the span of the generator. When a larger following model was tested, whose span was 50 percent of that of the generator, the effectiveness of the two spoilers per wing was substantially reduced.

Corsiglia, V. R.↗
NASA NTRS1990

Aeolian removal of dust from photovoltaic surfaces on Mars

It is well documented that Mars is totally engulfed in huge dust storms nearly each Martian year. Dust elevated in these global dust storms, or in any of the numerous local dust storms could settle on photovoltaic surfaces and seriously hamper photovoltaic power system performance. Using a recently developed technique to uniformly dust simulated photovoltaic surfaces, samples were subjected to Martian-like winds in an attempt to determine whether natural aeolian processes on Mars would sweep off the settled dust. The effects of wind velocity, angle of attack, height off the Martian surface, and surface coating material were investigated. Principles which can help to guide the design of photovoltaic arrays bound for the Martian surface were uncovered. Most importantly, arrays mounted with an angle of attack approaching 45 deg show the most efficient clearing. Although the angular dependence is not sharp, horizontally mounted arrays required significantly higher wind velocities to clear off the dust. From the perspective of dust-clearing it appears that the arrays may be erected quite near the ground, but previous studies have suggested that saltation effects can be expected to cause such arrays to be covered by sand if they are set up less than about a meter from the ground. Providing that the surface chemistry of Martian dusts is comparable to our test dust, the materials used for protective coating may be optimized for other considerations such as transparency, and chemical or abrasion resistance. The static threshold velocity is low enough that there are regions on Mars which experience winds strong enough to clear off a photovoltaic array if it is properly oriented. Turbulence fences proved to be an ineffective strategy to keep dust cleared from the photovoltaic surfaces.

Gaier, James R.↗
NASA NTRS1985

Assessment of wind tunnel corrections for multielement airfoils at transonic speeds

A finite volume formulation of the Euler equations using Cartesian grids is used to calculate the transonic flow over multielement airfoils and to use the resulting solutions to assess wall interference effects in wind tunnels. Available methods and recommendations for evaluating such effects, which are based on shifts in Mach number and angle of attack, are examined and the results are compared with measurements using the flapped supercritical SKF 1.1 airfoil. Based on the calculations, it is concluded that shifts in Mach number and angle of attack cannot by themselves account for viscous and wall effects on multielement airfoils at transonic speeds.

Gaffney, R. L., Jr.↗
DOE OSTI2026

Impact of atmospheric turbulence on performance and loads of wind turbines: knowledge gaps and research challenges

Wind energy harvesting from the atmosphere takes place in the atmospheric boundary layer. The boundary layer shear and buoyancy create three-dimensional turbulent eddies spanning a range of scales that form a continuous forward cascade of kinetic energy to the smallest scales of motion where energy is dissipated. Large-scale atmospheric circulations modulate the boundary layer turbulence, characterized by coherence and intermittency. As wind turbines grow in size and the integrated control of both turbines and wind farms spans greater distances, the relationship between the scales of atmospheric turbulence and the design and operation of wind energy facilities has entered new territory. The boundary layer turbulence impacts both wind turbine power production and turbine loads. Optimizing wind turbine and wind farm performance requires an understanding of how turbulence affects both wind turbine efficiency and reliability. While the characteristics of atmospheric boundary layer turbulence have been observed and studied in detail over the last few decades, there are still significant gaps in our understanding of the impact of turbulence on wind power resources and wind farm operations. This paper outlines the current state of turbulence research relevant to wind energy applications and points to gaps in our knowledge that need to be addressed to effectively utilize wind resources.

Kosović, Branko [Johns Hopkins Univ., Baltimore, M↗