Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - ASPECT RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

The aerodynamic analysis of the gyroplane rotating-wing system

An aerodynamic analysis of the gyroplane rotating-wing system is presented herein. This system consists of a freely rotating rotor in which opposite blades are rigidly connected and allowed to rotate or feather freely about their span axis. Equations have been derived for the lift, the lift-drag ratio, the angle of attack, the feathering angles, and the rolling and pitching moments of a gyroplane rotor in terms of its basic parameters. Curves of lift-drag ratio against lift coefficient have been calculated for a typical case, showing the effect of varying the pitch angle, the solidarity, and the average blade-section drag coefficient. The analysis expresses satisfactorily the qualitative relations between the rotor characteristics and the rotor parameters. As disclosed by this investigation, the aerodynamic principles of the gyroplane are sound, and further research on this wing system is justified.

Wheatley, John B↗
NASA NTRS2003

Vortex Flows at Supersonic Speeds

A review of research conducted at the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) into high-speed vortex flows during the 1970s, 1980s, and 1990s is presented. The data are for flat plates, cavities, bodies, missiles, wings, and aircraft with Mach numbers of 1.5 to 4.6. Data are presented to show the types of vortex structures that occur at supersonic speeds and the impact of these flow structures on vehicle performance and control. The data show the presence of both small- and large-scale vortex structures for a variety of vehicles, from missiles to transports. For cavities, the data show very complex multiple vortex structures exist at all combinations of cavity depth to length ratios and Mach number. The data for missiles show the existence of very strong interference effects between body and/or fin vortices. Data are shown that highlight the effect of leading-edge sweep, leading-edge bluntness, wing thickness, location of maximum thickness, and camber on the aerodynamics of and flow over delta wings. Finally, a discussion of a design approach for wings that use vortex flows for improved aerodynamic performance at supersonic speeds is presented.

Wood, Richard M.↗
NASA NTRS1976

Wing shielding of high velocity jet and shock-associated noise with cold and hot flow jets

Jet exhaust noise shielding data are presented for cold and hot flows (ambient to 1,100 K) and pressure ratios from 1.7 to 2.75. A nominal 9.5-cm diameter conical nozzle was used with simple shielding surfaces that were varied in length from 28.8 to 114.3 cm. The nozzle was located 8.8 cm above the surfaces. The acoustic data with the various sheilding lengths are compared to each other and to that for the nozzle alone. In general, short shielding surfaces that provided shielding for subsonic jets did not provide as much shielding for jets with shock noise, however, long shielding surfaces did shield shock noise effectively.

Vonglahn, U.↗
NASA NTRS1976

Wing shielding of high-velocity jet and shock-associated noise with cold and hot flow jets

Jet exhaust noise shielding data are presented for cold and hot flows (ambient to 1100 K) and pressure ratios from 1.7 to 2.75. A nominal 9.5-cm diameter conical nozzle was used with simple shielding surfaces that were varied in length from 28.8 to 114.3 cm. The nozzle was located 8.8 cm above the surfaces. The acoustic data with the various shielding lengths are compared to each other and to that for the nozzle alone. In general, short shielding surfaces that provided shielding for subsonic jets did not provide as much shielding for jets with shock noise; however, long shielding surfaces did shield shock noise effectively.

Von Glahn, U.↗
NASA NTRS1995

Experimental investigation of the inlet detector configuration variation in the flow field at Mach 1.9

In recent years, active research has been conducted to study the technological feasibility of supersonic laminar flow control on the wing of the High Speed Civil Transport (HSCT). For this study, the F-16XL has been chosen due to its highly swept crank wing planform that closely resembles the HSCT configurations. During flights, it is discovered that the shock wave generated from the aircraft inlet introduces disturbances on the wing where the data acquisition is conducted. The flow field about a supersonic inlet is characterized by a complex three dimensional pattern of shock waves generated by the geometrical configuration of a deflector and a cowl lip. Hence, in this study, experimental method is employed to investigate the effects of the variation of deflector configuration on the flow field, and consequently, the possibility of diverting the incoming shock-disturbances away from the test section. In the present experiments, a model composed of a simple circular tube with a triangular deflector is designed to study the deflector length and the deflector base width variation in the flow field. Experimental results indicate that the lowest external pressure ratio is observed at the junction where the deflector lip and the inlet cowl lip merge. Also, it is noted that the external pressure ratio, the internal pressure ratio, the coefficient of spillage drag, and the shock standoff distance decrease as the deflector length increases. In addition, the Redefined Total Pressure Recovery Ratio (RTPRR) increases with an increase in the deflector length. Results from the study of the effect of the deflector's base width variation on the flow field indicate that the lowest external pressure ratio is observed at the junction between the inlet cowl lip and the deflector lip. As the base width of the deflector increases, the external pressure ratio at 0 rotation increases, whereas the external pressure ratio at 180 rotation decreases. In addition, the internal pressure ratio and the coefficient of spillage drag decrease as the base width of the deflector increases. However, RTPRR and shock standoff distance increase as the base width increases. In conclusion, as deflector dimensions vary, distinctive patterns in the pressure variation around the inlet deflector are observed. With an increase in the deflector length and base width, the magnitude of shock-disturbances are weakened due to a decrease in the external pressure ratio. Also, as the deflector length and base width increase, a smaller bow shock angle is formed. Therefore, the inlet shock wave formation would be significantly altered, and consequently, shock disturbances on the wing test section can be avoided through appropriately designing the deflector.

Hwang, Kyu C.↗
NASA NTRS1961

Effects of Various Arrangements of Slotted and Round Jet Exits on the Lift and Pitching-Moment Characteristics of a Rectangular-Base Model at Zero Forward Speed

An investigation was made to determine some of the effects of various arrangements of slotted and round jet exits on the lift and pitching-moment characteristics of a rectangular-base model at zero forward speed. Jet-exit slots near the perimeter of the model usually gave larger lift-thrust ratios than slots nearer the center line when the model was near the ground, but away from the ground perimeter jets forming almost a closed jet curtain induced negative pressures on the bottom of the model and resulted in less lift than that obtained with more centrally located jets or jets with large gaps in the jet curtain. Most models with jet slots symmetrical about the pitch axis gave approximately zero pitching moments through the range of ground-board distances, but under some conditions unstable flow direction caused positive or negative pitching moments to occur. With wings attached to the models, the lift close to the ground was 10 to 20 percent less than the lift away from the ground for various configurations. The round jets gave poorer lift-thrust ratios than the slotted jets in the region of ground effect. Out of the region of ground effect the round jets gave the greatest lift-thrust ratio per unit of weight rate of flow of air, for equal jet-exit areas, and the thinnest slotted jet gave the least.

Vogler, Raymond D.↗
NASA NTRS1980

Dynamic response of a forward-swept-wing model at angles of attack up to 15 deg at a Mach number of 0.8

Root mean square (rms) bending moments for a dynamically scaled, aeroelastic wing of a proposed forward swept wing, flight demonstrator airplane are presented for angles of attack up to 15 deg at a Mach number of 0.8 The 0.6 size semispan model had a leading edge forward sweep of 44 deg and was constructed of composite material. In addition to broad band responses, individual rms responses and total damping ratios are presented for the first two natural modes. The results show that the rms response increases with angle of attack and has a peak value at an angle of attack near 13 deg. In general, the response was characteristic of buffeting and similar to results often observed for aft swept wings. At an angle of attack near 13 deg, however, the response had characteristics associated with approaching a dynamic instability, although no instability was observed over the range of parameters investigated.

Doggett, R. V., Jr.↗
NASA NTRS1999

A Performance Assessment of Eight Low-Boom High-Speed Civil Transport Concepts

A performance assessment of eight low-boom high speed civil transport (HSCT) configurations and a reference HSCT configuration has been performed. Although each of the configurations was designed with different engine concepts, for consistency, a year 2005 technology, 0.4 bypass ratio mixed-flow turbofan (MFTF) engine was used for all of the performance assessments. Therefore, all original configuration nacelles were replaced by a year 2005 MFRF nacelle design which corresponds to the engine deck utilized. The engine thrust level was optimized to minimize vehicle takeoff gross weight. To preserve the configuration's sonic-boom shaping, wing area was not optimized or altered from its original design value. Performance sizings were completed when possible for takeoff balanced field lengths of 11,000 ft and 12,000 ft, not considering FAR Part 36 Stage III noise compliance. Additionally, an arbitrary sizing with thrust-to-weight ratio equal to 0.25 was performed, enabling performance levels to be compared independent of takeoff characteristics. The low-boom configurations analyzed included designs from the Boeing Commercial Airplane Group, Douglas Aircraft Company, Ames Research Center, and Langley Research Center. This paper discusses the technology level assumptions, mission profile, analysis methodologies, and the results of the assessment. The results include maximum lift-to-drag ratios, total fuel consumption, number of passengers, optimum engine sizing plots, takeoff performance, mission block time, and takeoff gross weight for all configurations. Results from the low-boom configurations are also compared with a non-low-boom reference configuration. Configuration dependent advantages or deficiencies are discussed as warranted.

Baize, Daniel G.↗
NASA NTRS1996

Application of pneumatic lift and control surface technology to advanced transport aircraft

The application of pneumatic (blown) aerodynamic technology to both the lifting and the control surfaces of advanced transport aircraft can provide revolutionary changes in the performance and operation of these vehicles, ranging in speed regime from Advanced Subsonic Transports to the High Speed Civil Transport, and beyond. This technology, much of it based on the Circulation Control Wing blown concepts, can provide aerodynamic force augmentations of 80 to 100 (i.e., return of 80-100 pounds of force per pound of input momentum from the blowing jet). This can be achieved without use of external mechanical surfaces. Clever application of this technology can provide no-moving-part lifting surfaces (wings/tails) integrated into the control system to greatly simplify aircraft designs while improving their aerodynamic performance. Lift/drag ratio may be pneumatically tailored to fit the current phase of the flight, and takeoff/landing performance can be greatly improved by reducing ground roll distances and liftoff/touchdown speeds. Alternatively, great increases in liftoff weights and payloads are possible, as are great reductions in wing and tail planform size, resulting in optimized cruise wing designs. Furthermore, lift generation independent of angle of attack provides much promise for increased safety of flight in the severe updrafts/downdrafts of microbursts and windshears, which is further augmented by the ability to sustain flight at greatly reduced airspeeds. Load-tailored blown wings can also reduce tip vorticity during highlift operations and the resulting vortex wake hazards near terminal areas. Reduced noise may also be possible as these jets can be made to operate at low pressures. The planned presentation will support the above statements through discussions of recent experimental and numerical (CFD) research and development of these advanced blown aerodynamic surfaces, portions of which have been conducted for NASA. Also to be presented will be predicted performance of advanced transports resulting from these devices. Suggestions will be presented for additional innovative high-payoff research leading to further confirmation of these concepts and their application to advanced efficient commercial transport aircraft.

Englar, Robert J.↗
NASA NTRS1971

Large-scale wind-tunnel investigation of a V/STOL transport model with podded lift fans forward and aft of a low mounted wing

A configuration with outboard pod mounted front fans and rear fans located in the wing trailing-edge and fuselage juncture might have superior induced lift and variation of moment with airspeed. A large scale investigation of this type of configuration was conducted in 40- by 80-foot wind tunnel. The model used was a low wing transport representative of currently operating aircraft. Two lift fans were placed in pods forward of and below the wing with the fan centerline near mid semi-span. Two rear fans were mounted at the wing trailing-edge close to the fuselage with the fan rotor in the wing chord plane. Fan performance was measured statically and with forward speed, and longitudinal aerodynamic characteristics were obtained with the fans operating at various tip-speed ratios.

Hall, L. P.↗
NASA NTRS1981

Experimental and analytical study of the longitudinal aerodynamic characteristics of analytically and empirically designed Strake-wing configurations at subcritical speeds

Sixteen analytically and empirically designed strakes have been tested experimentally on a wing-body at three subcritical speeds in such a way as to isolate the strake-forebody loads from the wing-afterbody loads. Analytical estimates for these longitudinal results are made using the suction analogy and the augmented vortex lift concepts. The synergistic data are reasonably well estimated or bracketed by the high- and low-angle-of-attack vortex lift theories over the Mach number range and up to maximum lift or strake-vortex breakdown over the wing. Also, the strake geometry is very important in the maximum lift value generated and the lift efficiency of a given additional area. Increasing size and slenderness ratios are important is generating lift efficiently, but similar efficiency can also be achieved by designing a strake with approximately half the area of the largest gothic strake tested. These results correlate well with strake-vortex-breakdown observations in the water tunnel.

Lamar, J. E.↗
NASA NTRS1985

Turbulent flow around a wing-fuselage type juncture

The flow over a 58-mm-thick uniform-thickness winglike body having a 1.5:1 elliptical leading edge and joined to a large flat plate (representing an aircraft fuselage) is characterized experimentally at freestream velocity 15 m/s, corresponding to Reynolds number 940,000/m, using hot-wire anemometry. The results are presented graphically, and it is found that the horseshoe vortex formed by the separation of the fuselage boundary layer ahead of the wing leading edge is effective in transporting turbulence and modifying the mean-flow characteristics and the turbulent-stress distribution. It is suggested that the slenderness ratio of the leading edge is the dominant factor affecting the strength and location of the vortex.

Kubendran, L. R.↗
NASA NTRS1985

Optimum configuration of high-lift aeromaneuvering orbital transfer vehicles in viscous flow

The results of an analysis to determine the geometrical configuration of an aeroassisted transfer vehicle with a high lift-to-drag ratio (L/D) are described and the constraints imposed on this type of entry vehicle are considered. The aerodynamic characteristics of three configurations, a flat-plate delta wing, a truncated straight cone, and a truncated bent biconic are compared. The effect of viscosity is included in the analysis which examines the rounding of the sharp leading edges. It is shown that, under the constraints of carrying a given volume in the dead air region, the values of L/D are similar for each configuration and that a small blunt leading edge only slightly affects each vehicle's aerodynamic performance, causing less than a 5 percent drop in L/D. The truncated bent biconic is found to be the only configuration that provides the necessary stabilizing moments.

Davies, C. B.↗
NASA NTRS1993

A study of the accuracy of neutrally buoyant bubbles used as flow tracers in air

Research has been performed to determine the accuracy of neutrally buoyant and near neutrally buoyant bubbles used as flow tracers in air. Theoretical, computational, and experimental results are presented to evaluate the dynamics of bubble trajectories and factors affecting their ability to trace flow-field streamlines. The equation of motion for a single bubble was obtained and evaluated using a computational scheme to determine the factors which affect a bubble's trajectory. A two-dimensional experiment was also conducted to experimentally determine bubble trajectories in the stagnation region of NACA 0012 airfoil at 0 deg angle of attack using a commercially available helium bubble generation system. Physical properties of the experimental bubble trajectories were estimated using the computational scheme. These properties included the density ratio and diameter of the individual bubbles. the helium bubble system was then used to visualize and document the flow field about a 30 deg swept semispan wing with simulated glaze ice. Results were compared to Navier-Stokes calculations and surface oil flow visualization. The theoretical and computational analysis have shown that neutrally buoyant bubbles will trace even the most complex flow patterns. Experimental analysis revealed that the use of bubbles to trace flow patterns should be limited to qualitative measurements unless care is taken to ensure neutral buoyancy. This is due to the difficulty in the production of neutrally buoyant bubbles.

Kerho, Michael F.↗
NASA NTRS2004

Experimental Hypersonic Aerodynamic Characteristics of the Space Shuttle Orbiter for a Range of Damage Scenarios

Aerodynamic tests in support of the Columbia accident investigation were conducted in two hypersonic wind tunnels at the NASA Langley Research Center, the 20-Inch Mach 6 Air Tunnel and the 20-Inch CF4 Tunnel. The primary purpose of these tests was to measure the forces and moments generated by a variety of outer mold line alterations (damage scenarios) using 0.0075-scale models of the Space Shuttle Orbiter. Simultaneously acquired global heat transfer mappings were obtained for a majority of the configurations tested. Test parametrics included angles of attack from 38 to 42 deg, unit Reynolds numbers from 0.3 x 10(exp 6) to 3.0 x 10(exp 6) per foot, and normal shock density ratios of 5 (Mach 6 air) and 12 (CF4). The damage scenarios evaluated included asymmetric boundary layer transition, gouges in the windward surface thermal protection system tiles, wing leading edge damage (partially and fully missing reinforced carbon-carbon (RCC) panels), deformation of the wing windward surface, and main landing gear and/or door deployment. The measured aerodynamic increments for the damage scenarios examined were generally small in magnitude, as were the flight-derived values during most of the entry prior to loss of communication. A progressive damage scenario is presented that qualitatively matches the flight observations for the STS-107 entry.

Brauckmann, Gregory J.↗
NASA NTRS1999

Experimental Investigation of a Point Design Optimized Arrow Wing HSCT Configuration

The M2.4-7A Arrow Wing HSCT configuration was optimized for straight and level cruise at a Mach number of 2.4 and a lift coefficient of 0.10. A quasi-Newton optimization scheme maximized the lift-to-drag ratio (by minimizing drag-to-lift) using Euler solutions from FL067 to estimate the lift and drag forces. A 1.675% wind-tunnel model of the Opt5 HSCT configuration was built to validate the design methodology. Experimental data gathered at the NASA Langley Unitary Plan Wind Tunnel (UPWT) section #2 facility verified CFL3D Euler and Navier-Stokes predictions of the Opt5 performance at the design point. In turn, CFL3D confirmed the improvement in the lift-to-drag ratio obtained during the optimization, thus validating the design procedure. A data base at off-design conditions was obtained during three wind-tunnel tests. The entry into NASA Langley UPWT section #2 obtained data at a free stream Mach number, M(sub infinity), of 2.55 as well as the design Mach number, M(sub infinity)=2.4. Data from a Mach number range of 1.8 to 2.4 was taken at UPWT section #1. Transonic and low supersonic Mach numbers, M(sub infinity)=0.6 to 1.2, was gathered at the NASA Langley 16 ft. Transonic Wind Tunnel (TWT). In addition to good agreement between CFD and experimental data, highlights from the wind-tunnel tests include a trip dot study suggesting a linear relationship between trip dot drag and Mach number, an aeroelastic study that measured the outboard wing deflection and twist, and a flap scheduling study that identifies the possibility of only one leading-edge and trailing-edge flap setting for transonic cruise and another for low supersonic acceleration.

Narducci, Robert P.↗
NASA NTRS1952

Experimental Investigation of a Two-dimensional Split-wing Ram-jet Inlet at Mach Number of 3.85

Performance characteristics of a two-dimensional isentropic diffuser have been experimentally determined at a Mach number of 3.85. At zero angle of attack, a maximum total-pressure recovery of 0.41 was obtained with a supercritical mass-flow ratio of 0.95. As a consequence of the twin-duct arrangement of the diffuser, a large discontinuity in pressure recovery and mass flow with a characteristic hysteresis was encountered between critical and subcritical operation. An asymmetric shock pattern with large-scale separation and flow reversal in one of the passages occurred at reduced mass flows. Pressure and force data presented for an angle-of-attack range from zero to 4 degrees.

DIFFUSERS, SUPERSONIC↗
NASA NTRSDate not supplied

Mass Estimation Relationships for Conceptual Design of Blended-Wing-Body Cabin with Advanced Structures

Blended-Wing-Body (BWB) achieve a higher L/D than conventional tube and wing aircraft due to aerodynamic shaping of the non-circular pressure vessel that is made feasible through advanced composite technologies such as Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS). Due to the relatively new nature of the BWB, sufficient historical data does not exist for conceptual aircraft designers to base their structural weight estimations on, especially for estimating weights of the pressurized cabin center body. This paper describes general parametric Mass Estimation Relationships (MERs) based on high fidelity finite element analysis using PRSEUS for estimating the weight of a BWB pressurized cabin structure that includes cabin area, center body sweep, fineness ratio, and take-off gross weight.

BWB↗