Search NASA⌕ Search

SEARCH · Search NASA

Results for “acoustically”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Acoustic source location in the secondary mixing region of a jet-blown flap using a cross-correlation technique

An experimental investigation of the acoustic sources in the secondary mixing region of a laboratory-scale jet-flap was made using a causality correlation technique. The processed signal of a hot-film anemometer probe was cross correlated with the output signal of a far-field microphone. Axial acoustic source strength distributions were measured for three far-field microphone locations: plus or minus 45 deg in the flyover plane and 45 deg in the sideline plane. These measurements showed that the acoustic sources in the secondary mixing region are highly directional, radiating much more effectively to the -45 deg-microphone, located below the plane of the flap surface. A relative maximum in the acoustic source strength measured for the microphones in the flyover plane occurred very near the flap trailing edge, which may be due to an edge amplification effect predicted by the theoretical work of Ffowcs Williams and Hall.

Becker, R. S.↗
NASA NTRS1977

Pulse analysis of acoustic emission signals

A method for the signature analysis of pulses in the frequency domain and the time domain is presented. Fourier spectrum, Fourier transfer function, shock spectrum and shock spectrum ratio were examined in the frequency domain analysis and pulse shape deconvolution was developed for use in the time domain analysis. Comparisons of the relative performance of each analysis technique are made for the characterization of acoustic emission pulses recorded by a measuring system. To demonstrate the relative sensitivity of each of the methods to small changes in the pulse shape, signatures of computer modeled systems with analytical pulses are presented. Optimization techniques are developed and used to indicate the best design parameter values for deconvolution of the pulse shape. Several experiments are presented that test the pulse signature analysis methods on different acoustic emission sources. These include acoustic emission associated with (a) crack propagation, (b) ball dropping on a plate, (c) spark discharge, and (d) defective and good ball bearings. Deconvolution of the first few micro-seconds of the pulse train is shown to be the region in which the significant signatures of the acoustic emission event are to be found.

Houghton, J. R.↗
NASA NTRS1976

Acoustic design of the QCSEE propulsion systems

Acoustic design features and techniques employed in the Quiet Clean Short-Haul Experimental Engine (QCSEE) Program are described. The role of jet/flap noise in selecting the engine fan pressure ratio for powered lift propulsion systems is discussed. The QCSEE acoustic design features include a hybrid inlet (near-sonic throat velocity with acoustic treatment); low fan and core pressure ratios; low fan tip speeds; gear-driven fans; high and low frequency stacked core noise treatment; multiple-thickness treatment; bulk absorber treatment; and treatment on the stator vanes. The QCSEE designs represent and anticipated acoustic technology improvement of 12 to 16 PNdb relative to the noise levels of the low-noise engines used on current wide-body commercial jet transport aircraft.

Loeffler, I. J.↗
NASA NTRS1979

Applications of velocity potential function to acoustic duct propagation and radiation from inlets using finite element theory

A finite element velocity potential program was developed to study acoustic wave propagation in complex geometries. For irrotational flows, relatively low sound frequencies, and plane wave input, the finite element solutions showed significant effects of inlet curvature and flow gradients on the attenuation of a given acoustic liner in a realistic variable area turbofan inlet. The velocity potential approach can not be used to estimate the effects of rotational flow on acoustic propagation, since the potential acoustic disturbances propagate at the speed of the media in sheared flow. Approaches are discussed that are being considered for extending the finite element solution to include the far field, as well as the internal portion of the duct. A new matrix partitioning approach is presented that can be incorporated in previously developed programs to allow the finite element calculation to be marched into the far field. The partitioning approach provided a large reduction in computer storage and running times.

Baumeister, K. J.↗
NASA NTRS1979

An acoustic emission study of plastic deformation in polycrystalline aluminium

Acoustic emission experiments were performed on polycrystalline and single crystal 99.99% aluminum while undergoing tensile deformation. It was found that acoustic emission counts as a function of grain size showed a maximum value at a particular grain size. Furthermore, the slip area associated with this particular grain size corresponded to the threshold level of detectability of single dislocation slip events. The rate of decline in acoustic emission activity as grain size is increased beyond the peak value suggests that grain boundary associated dislocation sources are giving rise to the bulk of the detected acoustic emissions.

Bill, R. C.↗
NASA NTRS1979

An experimental investigation of acoustic radiation from a source inside a large turbulent free jet

An experiment has been conducted in NASA Langley's free-jet anechoic facility to assess the effect of a free-jet shear layer on sound radiation from an acoustic source placed inside the jet. The nozzle diameter was 1.22 m and operated at an exit velocity of 35 m/s. Two different types of sources were used; one was a compact source with a nearly uniform radiation pattern, the other was a noncompact source with highly directional radiation pattern. The acoustic source was driven by pure tone and 1/3-octave band white noise. Acoustic measurements were made both inside the jet flow in the potential core region and outside the jet in the acoustic farfield. The effects of mean flow convection and mean shear refraction on sound radiation were determined. The experimental results compared favorably with analytical predictions. The effect of free-jet turbulence on sound scattering was found to be insignificant.

Ozkul, A.↗
NASA NTRS1979

A comparison of linear acoustic theory with experimental noise data for a small-scale hovering rotor

Linear acoustic calculations based on full aerodynamic data as input are presented and compared with measured cases reported by Boxwell et al. (1978). The full aerodynamic data are obtained using three programs giving radial loading, chordwise loading, and chordwise position of transition. It is shown that in the theoretical results the most significant noise source mechanism is due to blade thickness. Thus the conclusions of Boxwell et al. as to the importance of nonlinearities around the blades are upheld. These conclusions concern the width, shape and the level of the acoustic pressure calculated from linear acoustic theory. Some of the approximations involved in the application of acoustic analogy using quadrupole sources are discussed. It is necessary that the near- and far-field problems of rotating blades be treated together as shown for the case of an oscillating sphere.

Farassat, F.↗
NASA NTRS1979

Applications of velocity potential function to acoustic duct propagation and radiation from inlets using finite element theory

A finite element velocity potential program has been developed to study acoustic wave propagation in complex geometries. For irrotational flows, relatively low sound frequencies, and plane wave input, the finite element solutions show significant effects of inlet curvature and flow gradients on the attenuation of a given acoustic liner in a realistic variable area turbofan inlet. In addition, as shown in the paper, the velocity potential approach can not be used to estimate the effects of rotational flow on acoustic propagation since the potential acoustic disturbances propagate at the speed of the media in sheared flow. Approaches are discussed that are being considered for extending the finite element solution to include the far field as well as the internal portion of the duct. A new matrix partitioning approach is presented that can be incorporated in previously developed programs to allow the finite element calculation to be marched into the far field. The partitioning approach provides a large reduction in computer storage and running times.

Baumeister, K. J.↗
NASA NTRS1979

Acoustic energy in ducts - Further observations

The transmission of acoustic energy in uniform ducts carrying uniform flow is investigated with the purpose of clarifying two points of interest. The two commonly used definitions of acoustic 'energy' flux are shown to be related by a Legendre transformation of the Lagrangian density exactly as in deriving the Hamiltonian density in mechanics. In the acoustic case the total energy density and the Hamiltonian density are not the same which accounts for two different 'energy' fluxes. When the duct has acoustically absorptive walls neither of the two flux expressions gives correct results. A reevaluation of the basis of derivation of the energy density and energy flux provides forms which yield consistent results for soft walled ducts.

Eversman, W.↗
NASA NTRS1978

Quiet, Clean, Short-Haul, Experimental Engine (QCSEE) Under-The-Wing (UTW) engine acoustic design

The acoustic considerations involved in the low source noise basic engine design and the design procedures followed in the development of the under-the-wing (UTW) engine boilerplate and composite nacelle acoustic treatment designs are presented. Laboratory experiments, component tests, and scale model and engine tests supporting the UTW engine acoustic design are referenced. Acoustic design features include a near-sonic inlet, low fan and core pressure ratios, low fan tip speed, high and low frequency stacked core treatment, multiple thickness treatment, and fan frame and stator vane treatment.

Sowers, H. D.↗
NASA NTRS1978

Quiet, Clean, Short-Haul Experimental Engine (QCSEE) Over-The-Wing (OTW) engine acoustic design

The acoustic considerations involved in the low source noise basic engine design and the design procedures followed in the development of the over-the-wing (OTW) nacelle acoustic treatment design are presented. Laboratory experiments, component tests, and scale model and engine tests supporting the OTW engine acoustic design are referenced. Acoustic design features include a near-sonic inlet, low fan and core pressure ratios, low fan tip speed, high and low frequency stacked core treatment, multiple thickness treatment, and fan frame and stator vane treatment.

Sowers, H. D.↗
NASA NTRS1980

Acoustic test and analyses of three advanced turboprop models

Results of acoustic tests of three 62.2 cm (24.5 inch) diameter models of the prop-fan (a small diameter, highly loaded. Multi-bladed variable pitch advanced turboprop) are presented. Results show that there is little difference in the noise produced by unswept and slightly swept designs. However, the model designed for noise reduction produces substantially less noise at test conditions simulating 0.8 Mach number cruise speed or at conditions simulating takeoff and landing. In the near field at cruise conditions the acoustically designed. In the far field at takeoff and landing conditions the acoustically designed model is 5 db quieter than unswept or slightly swept designs. Correlation between noise measurement and theoretical predictions as well as comparisons between measured and predicted acoustic pressure pulses generated by the prop-fan blades are discussed. The general characteristics of the pulses are predicted. Shadowgraph measurements were obtained which showed the location of bow and trailing waves.

Brooks, B. M.↗
NASA NTRS1980

Acoustic characteristics of two hybrid inlets at forward speed

A wind tunnel investigation of the acoustic and aerodynamic characteristics of two hybrid inlets installed on a JT15D-1 turbofan engine was performed. The hybrid inlets combined moderate throat Mach number and wall acoustic treatment to suppress the fan inlet noise. Acoustic and aerodynamic data were recorded over a range of flight and engine operating conditions. In a simulated flight environment, the hybrid inlets provided significant levels of suppression at both design and off-design throat Mach numbers with good aerodynamic performance. A comparison of inlet noise at quasi-static and forward-speed conditions in the wind tunnel showed a reduction in the fan tones, demonstrating the flight cleanup effect. High angles of attack produced slight increases in fan noise at the high acoustic directivity angles.

Falarski, M. D.↗
NASA NTRS1979

Shuttle bay acoustics

Acoustic energy generated during Shuttle liftoff will propagate up the orbiter vehicle, transmit through the payload bay structure, and produce an intense acoustic field inside the bay with the potential for damaging relatively fragile payload components. This paper describes three experimental programs aimed at investigating Shuttle bay acoustics. The first two experiments, conducted in July 1976 and January 1977 respectively, were concerned primarily with establishing the noise reduction of the OV101 payload bay structure; the third set of experiments, carried out during April and May 1978, was concerned with the influence of payloads on the bay acoustic levels. Test results are summarized, and comparisons with analytical model predictions are presented.

Piersol, A. G.↗
NASA NTRS1980

Acoustic loading in straight pipes

Based on linear one-dimensional acoustics, a geometrically perfect elastic waveguide would respond to an oscillatory internal pressure only in the presence of path deflectors (elbows and branches). In practice, a significant elasto-acoustic interaction results even in straight conduits as a result of manufacturing tolerances. A theoretical model of the linear acoustic loading in straight pipes is developed that considers the acoustic wave distortion due to perimeter, axial, and wall thickness nonuniformities.

El-Raheb, M.↗
NASA NTRS1980

Some aspects of the comparison between optics and nonlinear acoustics

Some results concerning nonlinear acoustics deduced from a comparison of nonlinear processes in optics and acoustics are discussed. An aspect of nonlinearity in acoustics connected with the dimensionality of the medium of propagation is emphasized and illustrated by the proof of static instability of an ideal linear solid. In addition a phenomenon, which can be called acoustical rectification by analogy with nonlinear optics, is propounded to measure the third order elastic constants. Its experimental consequences are predicted in a particular case.

Perrin, B.↗
NASA NTRS1981

Examination of silicon solar cells by means of the Scanning Laser Acoustic Microscope (SLAM)

The Scanning Laser Acoustic Microscope produces images of internal structure in materials. The acoustic microscope is an imaging system based upon acoustic rather than electromagnetic waves. Variations in the elastic propertis are primarily responsible for structure visualized in acoustic micrographs. The instrument used in these investigations is the SONOMICROSCOPE 100 which can be operated at ultrasonic frequencies of from 30 MHz to 500 MHz. The examination of the silicon solar cells was made at 100 MHz. Data are presented in the form of photomicrographs.

Vorres, C.↗
NASA NTRS1981

Vibrations of three-dimensional pipe systems with acoustic coupling

A general algorithm is developed to calculate the beam-type dynamic response of three dimensional multiplane finite length pipe systems, consisting of elbow and straight ducts with continuous interfaces. Emphasis is on secondary acoustic wave effects giving rise to coupling mechanisms; and the simulation accounts for one-dimensional elastoacoustic coupling from a plane acoustic wave and secondary loads resulting from wave asymmetries. The transfer matrix approach is adopted in modeling the elastodynamics of each duct, with allowance for distribution loads. Secondary loads from plane wave distortion are considered with a solution of the Helmholtz equation in an equivalent rigid waveguide, and effects of path imperfection are introduced as a perturbation from the hypothetical perfectly straight pipe. Computations indicate that the one-dimensional acoustic assumption is valid for frequencies below one-half the first cut-off frequency, and the three-dimensional acoustic effects produce an increase in response levels near and above cut-off.

El-Raheb, M.↗