Search NASA⌕ Search

SEARCH · Search NASA

Results for “bedding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Thermochemical reduction modeling in a high-temperature moving-bed reactor for energy storage: 1D model

The design of robust and efficient high-temperature thermochemical reactors and determination of operating conditions are critical steps toward enabling high-efficiency long-duration solar energy storage. This work presents a computational model for the thermal reduction of a metal oxide material (Mg-Mn-O) up to 1450 °C and the coupled complex transport phenomena in a novel tubular thermal reactor design that features the capability for a high extent-of-reduction (high energy storage density) and inherent heat recuperation. A one-dimensional model coupling counter-current gas–solid flow, two-phase heat transfer, thermochemical redox reactions, and species transport in a moving-bed reactor is developed. Simplified versions of the model are validated with published results in the literature for packed beds with both inert and reactive particles; the fully coupled model is also validated with experimental measurements of a moving-bed reactor in terms of local temperatures and oxygen release at the exit. Detailed comparisons on the effects of different boundary conditions in the reaction zone (prescribed wall temperature vs. heat flux conditions) and formulations based on a simple uniform flow assumption vs. plug flow using Ergun equation for gas flow are investigated. The results are compared with experimental measurements, and for all cases, the energy flow components in the reactor system and the thermal to chemical conversion efficiency and overall system efficiency are computed. Finally, the predicted high thermal-to-chemical efficiency ~95% and system efficiency ~30% agree with experimental measurements.

25 ENERGY STORAGE↗

A new model for two-dimensional numerical simulation of pseudo-2D gas-solids fluidized beds

Pseudo-two dimensional (pseudo-2D) fluidized beds, for which the thickness of the system is much smaller than the other two dimensions, is widely used to perform fundamental studies on bubble behavior, solids mixing, or clustering phenomenon in different gas-solids fluidization systems. The abundant data from such experimental systems are very useful for numerical model development and validation. However, it has been reported that two-dimensional (2D) computational fluid dynamic (CFD) simulations of pseudo-2D gas-solids fluidized beds usually predict poor quantitative agreement with the experimental data, especially for the solids velocity field. In this paper, a new model is proposed to improve the 2D numerical simulations of pseudo-2D gas-solids fluidized beds by properly accounting for the frictional effect of the front and back walls. Two previously reported pseudo-2D experimental systems were simulated with this model. Compared to the traditional 2D simulations, significant improvements in the numerical predictions have been observed and the predicted results are in better agreement with the available experimental data.

42 ENGINEERING↗

Chemical redox of lithium-ion solid electroactive material in a packed bed flow reactor

Chemical redox reactions between solid electroactive materials and dissolved electroactive compounds are a necessary component of emerging technologies relevant to renewable energy including high energy density flow batteries and battery material recycling. In this work, an initial investigation of heterogeneous chemical redox for a packed bed reactor configuration between solid electroactive material and dissolved redox shuttles will be described. Experimental conditions including the height of the packed bed, the redox shuttle solution concentration, solution flow rate, and operating temperature were varied and their impact on the molar conversion of the solid electroactive material in the packed bed was quantified using electroanalytical techniques on the reactor effluent. The progression of the reaction and its dependence on the different variables explored will be discussed in the context of the limiting processes for porous packed aggregates of the solid electroactive material undergoing chemical oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling and experimental validation of direct contact crossflow packed beds condenser used in HDH desalination systems

Humidification and dehumidification (HDH) desalination systems are alternatives to reverse osmosis desalination systems, especially for high salinity waters. A HDH system is essentially equipped with a humidifier (also called as evaporator) for air to pick up vapor from saline water, a dehumidifier (also called as condenser) to produce freshwater, and a heating source. HDH systems based on direct contact packed beds heat exchangers have remarkably lower costs than traditional HDH systems due to their inexpensive materials and simple configurations. This paper specifically focuses on direct contact crossflow packed beds condensers, in which cooling water vertically drips through the packed beds, directly contacting the horizontal air-vapor flow. A two-dimensional mathematical model that solves for the enthalpy values of the working fluids is proposed in this paper, and the PDEs are solved using finite differences. To validate the model, an experimental condenser was built and tested. Water temperatures inside the test section at twenty-nine locations were measured, as well as the air vapor temperatures of five locations at the outlet. The measured water and air-vapor temperatures agree with the simulation results with less than 10 % error in most of the compared domain.

42 ENGINEERING↗

Computational fluid dynamic analysis of a novel particle-to-air fluidized-bed heat exchanger for particle-based thermal energy storage applications

Long-duration energy storage technologies are being targeted to enable cost-effective, decarbonized energy systems. Particle-based thermal energy storage systems are one promising technology by storing excess electricity or heat as sensible thermal energy in inexpensive, solid, inert particles. These systems are only possible if an effective and economical particle-to-working fluid heat exchanger exists. This study predicts the performance of a proposed, direct-contact, particle-to-air, pressurized fluidized-bed heat exchanger using computational fluid dynamics. The common Eulerian-Eulerian framework for modeling fluidized beds is first benchmarked to experimental results at a previously untested operating condition and application. Then, the benchmarked model evaluates the performance of a proposed design for a commercial-scale version of the novel particle-to-air heat exchanger. The results show pressure drop and gas-phase approach temperatures are advantageous compared to other proposed designs for particle-to-air heat exchangers in the literature; approach temperatures were less than 5 °C and gas-phase pressure drop across the fluidized bed was 32 kPa. The model also highlights the importance of gas distributor design and representation in the Eulerian-Eulerian framework to control fluidization behavior. In conclusion, the model built and benchmarked in this study can be leveraged to advance the design and analysis of these heat exchangers critical to the deployment of a promising long-duration energy storage technology.

25 ENERGY STORAGE↗

An advanced evaluation of spouted beds scale-up for coating TRISO nuclear fuel particles using Radioactive Particle Tracking (RPT)

A set of dimensionless groups has been proposed in the literature by He et al. (1997) to scale-up gas-solid spouted beds while maintaining their hydrodynamics similarity. The literature reported studies do not provide conclusive assessments about this methodology. Therefore, in this work, we have applied an advanced non-invasive Radioactive Particle Tracking (RPT) technique for the first time to evaluate such scale-up methodology by measuring the local solids velocity, normal and shear stresses and the turbulent kinetic energy. The axial and azimuthal averaged radial profiles of solids velocity, normal stresses, shear stresses, and turbulent kinetic energy illustrate that the similarity of the hydrodynamics has not been attained when the proposed set of dimensionless groups has been matched using two sizes of spouted beds of 0.076 m and 0.152 m and sets of operating conditions. The conclusion is consistent with the recent reported findings by measuring cross sectional distribution and radial profiles of solids and gas holdups along the bed height using gamma-ray computed tomography and by the limited point measurements of solids velocity and holdup using optical fiber probe. It is clear that local measurements of hydrodynamic parameters are essential for detailed assessment of scale-up methodologies. Here, the presented results of our work in terms of the components profiles of the particles radial velocities and turbulent parameters are also valuable for benchmarking computational fluid dynamics codes and models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modeling the impact of bubbling bed hydrodynamics on tar yield and its fluctuations during biomass fast pyrolysis

The impact of bubbling bed hydrodynamics on temporal variations in the exit tar yield for biomass fast pyrolysis was investigated using computational simulations of an experimental laboratory-scale reactor. A multi-fluid computational fluid dynamics model was employed to simulate the differential conservation equations in the reactor, and this was combined with a multi-component, multi-step pyrolysis kinetics scheme for biomass to account for chemical reactions. The predicted mean tar yields at the reactor exit appear to match corresponding experimental observations. Parametric studies predicted that increasing the fluidization velocity should improve the mean tar yield but increase its temporal variations. Increases in the mean tar yield coincide with reducing the diameter of sand particles or increasing the initial sand bed height. However, trends in tar yield variability are more complex than the trends in mean yield. The standard deviation in tar yield reaches a maximum with changes in sand particle size. As a result, the standard deviation in tar yield increases with the increases in initial bed height in freely bubbling state, while reaches a maximum in slugging state.

09 BIOMASS FUELS↗

Isotherm modeling and techno-economic analysis of a TSA moving bed process using a tetraamine-appended MOF for NGCC applications

Tetraamine-appended metal-organic frameworks (MOF) are a new family of amine-functionalized MOF materials that show potential for CO 2 capture from flue gas conditions relevant to natural gas combined cycle (NGCC) power plants. This work presents isotherm modeling of the tetraamine-appended MOF Mg 2 (dobpdc)(3-4-3)(dobpdc 4- =4,4'-dioxidobiphenyl-3,3'dicarboxylate;3-4-3=N,N'bis(3-aminopropyl)-1,4-diaminobutane), process modeling, scale up, and a techno-economic optimization of a moving bed Temperature Swing Adsorption (TSA) process for carbon capture using this sorbent. This MOF exhibits a unique two-step CO 2 adsorption profile in three different pressure ranges. Thus, arctangent-based logistic functions and, quadratic and Langmuir models were employed to represent such isotherm behavior. The results of the isotherm model show good fitting vs the experimental data with an RMSE of 0.41. Here, to model the carbon capture process, the isotherm model was embedded into a moving bed contactor model, and this was used to simulate a TSA CO 2 capture cycle and evaluate cost-optimal designs considering flue gas from a -650 MWe NGCC power plant. The capital cost model consists of CAPEX correlations for reactors, compressors, ducting, etc., while the operating costs include steam, water, chemicals, and electricity (following NETL's quality guidelines for energy systems studies). A techno-economic optimization of the capture system was performed by using NETL's Framework for the Optimization and Quantification of Uncertainty and Surrogates tool (FOQUS). Results suggest that a moving bed carbon capture system with tetraamine-appended MOF can be competitive compared to conventional MEA solvent-based capture processes for NGCC plants, when a heat recovery efficiency of at least 40% is achieved, and MOF materials can be produced at a cost below -$9/kg.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A numerical study of the spectral radiative properties of packed bed with mixed bauxite and silica spheres

Bauxite and silica particles have gained increasing attention for applications in the field of concentrated solar power. In this work, a Monte Carlo ray-tracing simulation is performed to predict the radiative properties (absorptance, reflectance, and transmittance) of packed beds with mixed bauxite and silica spherical particles at wavelengths of 0.5, 2.6, 9.0, and 9.35 µm. These wavelengths are representative for the visible, near-infrared, and the mid-infrared regions that are important for solar and thermal radiation, respectively. A repeating unit-column approach is used to mathematically represent the particle bed. The effects of particle mixing ratio, volume fraction, and wavelength on the predicted radiative properties are examined. The obtained radiative properties are inputted to an inverse method to retrieve the effective absorption and scattering coefficients as well as the scattering albedo, which may be later used in a continuous-scale radiative heat transfer analysis. Furthermore, the independent scattering model is used to obtain the absorption coefficient and scattering albedo based on the absorption and scattering cross sections predicted by a Monte Carlo algorithm for a single particle. It is shown that the independent scattering model underpredicts the scattering coefficient for opaque particles but overpredicts the scattering coefficient for semitransparent particles for sufficiently high particle volume fractions. Here, the radiative properties calculated from the independent scattering model are compared to the full Monte Carlo simulation of the particle bed to examine the influence of particle mixing on dependent scattering.

42 ENGINEERING↗

Particle-wall heat transfer in narrow-channel bubbling fluidized beds for thermal energy storage

Robust metal oxide particles can provide low-cost and stable thermal energy storage (TES) to temperatures up to 1200 °C or higher. The transfer of heat into and out of the particles in cost-effective high-temperature particle heat exchangers remains a principal challenge to implementing particle-based TES. The present work expands on prior studies of particle-wall heat transfer in narrow-channel fluidized beds operated in the bubbling fluidization regime. Batch-mode experiments with various oxide particles over a range of temperatures and airflow rates indicate that particle-wall heat transfer increases with higher bed temperature and decreasing particle size. Measured particle-wall heat transfer coefficients in a 12 mm deep channel are fit to a Nusselt number correlation proportional to a non-monotonic function of excess fluidization velocity. Particle-wall heat transfer coefficients rise rapidly with excess fluidization velocities until reaching a maximum at intermediate air velocities due to a trade-off between enhanced transverse particle mixing and decreasing particle volume fraction with increased fluidization velocity. The heat transfer coefficient reaches a maximum of ≈ 400% of values without fluidization for oxide particles ranging in diameter d p from 159 to 408 μm. For the smallest particles tested, composed of olivine sand, particle-wall heat transfer coefficients peak above 1100 Wm –2 K –1 at 450 °C. 100-h tests at 500 °C and near-optimal heat transfer fluidization velocities indicated minimal wall wear or oxide scaling. Furthermore, high particle-wall heat transfer coefficients suggest narrow channel fluidized beds as a potential pathway for reducing the required surface area and cost of high-temperature particle heat exchangers, as needed in large-scale thermal energy storage applications.

14 SOLAR ENERGY↗

An improved pressure drop correlation for modeling localized effects in a pebble bed reactor

Advances in the development of pebble bed reactors (PBRs) has created a desire for accurate and cost-effective simulation tools for design scoping studies and safety analysis. The current state-of-the-art for these simulations is the use of porous media models, although these models rely on correlations to capture the effects of flow features that are not explicitly modeled. One of the areas where correlation accuracy is currently lacking is in the near-wall region of the bed. In this region, the presence of the wall causes the pebbles to pack more orderly, drastically changing the geometry and flow behavior in this region. This work presents a new generalized pressure drop correlation for PBRs based on the KTA equation. A high-to-low methodology is applied, where large eddy simulation (LES) is performed on two beds of 1568 and 1700 pebbles to generate a high-fidelity dataset. The flow fields are then averaged in time and separated into concentric rings of 0.05 D peb width. Average porosity, velocity, and pressure drop are extracted for each ring and the friction and form losses are calculated. The Reynolds number range for this study is 625–10,000, and thus the form losses are dominant over the friction losses. The form losses across the rings are investigated, and a correction term for the form loss calculation is determined and applied to the KTA equation to drastically improve the capability of modeling localized porosity effects in a porous media code. Finally, the improved correlation reduces near-wall velocity prediction error from over 50% with the KTA correlation to around 5%. Agreement in pressure drop prediction between LES and porous media simulations is also improved.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Sensitivity analysis, surrogate modeling, and optimization of pebble-bed reactors considering normal and accident conditions

This research provides a valuable tool that streamlines the optimization process while significantly increasing its accuracy. This study creates a robust framework for reactor design optimization by incorporating comprehensive modeling using the Comprehensive Reactor Analysis Bundle, or BlueCRAB, within the Multiphysics Object-Oriented Simulation Environment (MOOSE). BlueCRAB is the United States Nuclear Regulatory Commission's code suite for non-light water reactor analysis and includes the Griffin, Pronghorn, and Bison applications. This not only improves the efficiency of the optimization process but also enhances the reliability of the results. Such a tool is essential for advancing the state-of-the-art in pebble-bed reactor technology and is critical for achieving the goals of Generation IV reactors, which aim for safe, sustainable, and economically viable nuclear energy solutions. This work presents and applies this workflow on pebble-bed reactors while considering both normal and off-normal conditions. A representative gas-cooled pebble-bed reactor at equilibrium core conditions serves as the nominal design specification for normal operation and is based on previous research. The depressurized loss-of-forced-cooling accident is deployed for off-normal conditions in this work. After defining design-related parameters and quantities of interest regarding reactor safety and performance, this multiphysics model is sampled using the MOOSE stochastic tools module. The result is a comprehensive dataset of configurations, enabling sensitivity analysis and the generation of surrogate models. Subsequently, the dataset and surrogate models are employed in two optimization studies aimed at maximizing fuel utilization and economic profit while adhering to safety and operational constraints. Performing the optimization process with fuel utilization as the metric leads to an improvement of approximately 10%, compared to engineering-judgment-based nominal conditions. The optimization on economic profit leads to an estimated increase of ~300 million USD over the lifetime of the reactor.

97 MATHEMATICS AND COMPUTING↗

An advanced evaluation of the mechanistic scale-up methodology of gas–solid spouted beds using radioactive particle tracking

For this work, we implemented for the first time our radioactive particle tracking as an advanced noninvasive technique to further evaluate and validate our newly developed mechanistic scale-up methodology based on matching the radial profile of the gas holdup. Two spouted beds with diameters of 0.076 and 0.152 m were used. Three sets of conditions were implemented; i.e., conditions of the reference case, conditions that provided a gas-holdup radial profile similar to that of the reference case, and conditions that provided a gas-holdup radial profile dissimilar to that of the reference case. The results confirm the validation of the scale-up methodology in terms of obtaining closer dimensionless values and radial profiles of components of the particle velocity, normal stress, shear stress, and turbulent kinetic energy. The results further advance the understanding of gas–solids spouted beds, provide deeper insight into the solids dynamics of the beds and present important benchmarking data for validating computational fluid dynamics codes and models.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Silicon Chemical Vapor Deposition on macro and submicron powders in a fluidized bed

Titanium oxide (TiO2) submicron powders have been treated by Chemical Vapor Deposition (CVD) in a vibro-fluidized bed in order to deposit silicon layers of nanometer scale on each individual grain from silane (SiH4). Experimental results show that for the conditions tested, the original granular structure of the powders is preserved for 90% of the initial bed weight while the remaining 10% consisted of agglomerates in millimetre range found near the distributor of the reactor. A comparison between experimental and modelling results using the MFIX code shows that for Geldart's Group B alumina particles (Al2O3), the model represents both the bed hydrodynamics and silane conversion rates quite well. The future objective is to extend the simulation capability to cohesive submicron powders in order to achieve better predictability of the phenomena governing ultrafine particles.

36 MATERIALS SCIENCE↗

Fluidized bed gasification of waste-derived fuels

Five alternative waste-derived fuels obtained from municipal solid waste and different post-consumer packaging were fed in a pilot-scale bubbling fluidized bed gasifier, having a maximum feeding capacity of 100 kg/h. The experimental runs utilized beds of natural olivine, quartz sand or dolomite, fluidized by air, and were carried out under various values of equivalence ratio. The process resulted technically feasible with all the materials tested. The olivine, a neo-silicate of Fe and Mg with an olive-green colour, has proven to be a good candidate to act as a bed catalyst for tar removal during gasification of polyolefin plastic wastes. Thanks to its catalytic activity it is possible to obtain very high fractions of hydrogen in the syngas (between 20% and 30%), even using air as the gasifying agent, i.e. in the most favourable economical conditions and with the simplest plant and reactor configuration. The catalytic activity of olivine was instead reduced or completely inhibited when waste-derived fuels from municipal solid wastes and aggregates of different post-consumer plastic packagings were fed. Anyhow, these materials have given acceptable performance, yielding a syngas of sufficient quality for energy applications after an adequate downstream cleaning.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal valorization of post-consumer film waste in a bubbling bed gasifier

Highlights: • Film waste from packaging is a common waste, a fraction of which is not recyclable. • Gasification can make use of the high energy value of the non-recyclable fraction. • This waste and two reference polymers were gasified in a bubbling bed reactor. • This experimental research proves technical feasibility of the process. • It also analyzes impact of composition and ER on the performance of the plant. - Abstract: The use of plastic bags and film packaging is very frequent in manifold sectors and film waste is usually present in different sources of municipal and industrial wastes. A significant part of it is not suitable for mechanical recycling but could be safely transformed into a valuable gas by means of thermal valorization. In this research, the gasification of film wastes has been experimentally investigated through experiments in a fluidized bed reactor of two reference polymers, polyethylene and polypropylene, and actual post-consumer film waste. After a complete experimental characterization of the three materials, several gasification experiments have been performed to analyze the influence of the fuel and of equivalence ratio on gas production and composition, on tar generation and on efficiency. The experiments prove that film waste and analogue polymer derived wastes can be successfully gasified in a fluidized bed reactor, yielding a gas with a higher heating value in a range from 3.6 to 5.6 MJ/m{sup 3} and cold gas efficiencies up to 60%.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Comparison of ANN (MLP), ANFIS, SVM, and RF models for the online classification of heating value of burning municipal solid waste in circulating fluidized bed incinerators

Highlights: • A rapid, cost-effective, and comparative methodology was proposed to evaluate the HVs of burning MSW online. • Models ranked in descending order of performance are ANFIS, RF, SVM, MLP. • A well trained model is capable of characterizing the variation trend of HVs accurately. - Abstract: The heating values, particularly lower heating values of burning municipal solid waste are critically important parameters in operating circulating fluidized bed incineration systems. However, the heating values change widely and frequently, while there is no reliable real-time instrument to measure heating values in the process of incinerating municipal solid waste. A rapid, cost-effective, and comparative methodology was proposed to evaluate the heating values of burning MSW online based on prior knowledge, expert experience, and data-mining techniques. First, selecting the input variables of the model by analyzing the operational mechanism of circulating fluidized bed incinerators, and the corresponding heating value was classified into one of nine fuzzy expressions according to expert advice. Development of prediction models by employing four different nonlinear models was undertaken, including a multilayer perceptron neural network, a support vector machine, an adaptive neuro-fuzzy inference system, and a random forest; a series of optimization schemes were implemented simultaneously in order to improve the performance of each model. Finally, a comprehensive comparison study was carried out to evaluate the performance of the models. Results indicate that the adaptive neuro-fuzzy inference system model outperforms the other three models, with the random forest model performing second-best, and the multilayer perceptron model performing at the worst level. A model with sufficient accuracy would contribute adequately to the control of circulating fluidized bed incinerator operation and provide reliable heating value signals for an automatic combustion control system.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Simulated Moving Bed Process for CO 2 Capture from Humid Postcombustion Flue Gases Using MUF-16

Simulated moving bed (SMB) designs are increasingly being adapted for the separation of multicomponent gaseous mixtures. In this work, we develop a modified SMB process for capturing CO 2 from humid postcombustion flue gas using MUF-16 (MUF = Massey University Framework). MUF-16 shows excellent selectivity for CO 2 over N 2 , moderate heats of adsorption for CO 2 and H 2 O, and no competitive sorption of CO 2 over water at relative humidities relevant to postcombustion capture. We utilize these characteristics to propose a continuous process that uses N 2 from the feed as the desorbent for the water, eliminating the need for a separate desiccant bed and allowing for localized heating during desorption for H 2 O-saturated MOF beds. Single-component isotherms, single-column breakthrough experiments, and SO 2 stability tests suggest the excellent suitability of MUF-16 to this separation via the proposed SMB design.

CO2 capture from humid flue gas↗