Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30

Lithiation-Induced Non-Noble Metal Nanoparticles for Li–O 2 Batteries

Low-cost and highly active electrocatalysts are attractive for Li-O 2 applications. Herein, a 3D interconnected plate architecture consisting of ultrasmall Co-Ni grains embedded in lithium hydroxide nanoplates (Co 2 Ni@LiOH) is designed and prepared by a lithiation strategy at room temperature. This catalyst exhibits a remarkably reduced charge potential of similar to 3.4 V at 50 mu A cm -2 , which leads to the high roundtrip efficiency of similar to 79%, among the best levels reported and a cycle life of up to 40 cycles. The well-aligned network facilitates the oxygen diffusion and the electrolyte match penetration into the electrode. The enhanced electrical conductivity net-work improves the charge transport kinetics and more active sites are exposed, which facilitate the adsorption and dissociation of oxygen during the oxygen reduction reaction and the oxygen evolution reaction. This new catalyst design inspires the development of an effective non-noble metal catalyst for Li-O 2 batteries.

25 ENERGY STORAGE↗

Development of sulfonated carbon-based solid-acid catalysts derived from biorefinery residues and biomass ash for xylan hydrolysis

In this study, biorefinery residues and biomass ash were used to develop sulfonated carbon-based solid-acid catalysts to enhance xylan hydrolysis. Here, metals extracted from the biomass ash were impregnated into a carbon support prepared from biorefinery residues to synthesize sulfonated ash-impregnated carbon-based catalyst. Metals present in the ash most probably are responsible for the increased acid density in the catalyst. Using this catalyst, 11.4 % xylose yield was produced, an increase of 171 % over the yield obtained from a catalyst without ash impregnation. Using a xylan-to-catalyst ratio of 1:2, 72.9 % xylose yield was obtained, comparable to using 0.5 wt% sulfuric acid under the same reaction condition. Moreover, this catalyst significantly inhibited xylose dehydration, only forming 11.3 % furfural compared to that generated using dilute acid. Hence, these results show the potential for using biomass ash as a metal source to increase the number of acid sites in solid-acid catalysts used for biomass pretreatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Enhanced Electro-Kinetics of C-C Bond-Splitting during Ethanol Oxidation Reaction using Pt/Rh/Sn Catalyst with a Partially Oxidized Pt and Rh Core and a SnO2 Shell

Direct ethanol fuel cell (DEFC) is a promising technology for generating electricity via the electro-oxidation of liquid ethanol. Its implementation requires the development of anode catalysts capable of producing CO 2 and yielding 12-electron transfer through breaking C-C bond of ethanol. Here we presented comprehensive studies of electro-kinetics of the CO 2 generation on Pt/Rh/Sn ternary catalysts. Our studies showed that, for the first time, the tri–phase PtRhOx- SnO 2 catalysts with a partially oxidized Pt and Rh core and a SnO 2 shell, validated by X-ray absorption analyses and scanning transmission electron microscope-electron energy loss spectroscopy line scan, coincided with a 2.5-fold increase in the CO 2 generation rate towards ethanol oxidation reaction, compared with the bi-phase PtRh-SnO 2 catalysts with a metallic PtRh alloy core and commercial Pt. These studies provided insight on the design of a new genre of electro-catalysts with a partially oxidized noble metal.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Improved Method for the Production of Tetrahydrofuran From Biomass

Statement of the Problem: Tetrahydrofuran (THF) is a large volume, commodity chemical used as a basic building block for polyurethane stretch fibers (Spandex), other elastomers, solvents for PVC cements, pharmaceuticals, and coatings. Current THF production requires petroleum-based raw materials and significant energy inputs, representing inefficient use of petroleum resources and placing the U.S. at a manufacturing disadvantage compared to chemical manufacturers in other world areas. Pulp and paper manufacture is one of the largest industries in the U.S., representing about 6% of the manufacturing sector of the U.S. GDP. In recent decades, the pulp and paper industry has struggled with a declining market, poor profitability, and competition from other world areas, leading to the shutdown of many U.S. pulp and paper mills, and loss of U.S. employment. The production of chemicals, such as THF from pulp and paper waste hydrolysate, can provide new technologies and products from pulp and paper manufacture which can enhance industry profitability. The iCARD technology will produce and sell THF from selected pulp and paper byproduct hydrolysates without deleterious effect on ongoing pulp production of the mill. Overall Objective: The overall goal of this Small Business Innovation Research Phase II Project was to complete the research, development, and design tasks required to commercialize an innovative technology using catalytic reactive distillation to achieve process intensification for the manufacture of “green” THF from pulp mill waste hydrolysate. The new technology will benefit the U.S. pulp and paper industry by providing new technologies and products from pulp and paper manufacture, which can enhance industry profitability, and increase industry employment. Development of commercially competitive biomass based technologies will reduce consumption of scarce hydrocarbon resources, and improve long term U.S. competitiveness in global markets. Conclusions: The novel catalytic reactive distillation technology successfully demonstrated the technical and economic feasibility of the manufacture of THF production from dilute aqueous biomass solutions. New catalyst compositions were developed with catalytic activity for conversion of furfural to THF which exceed the activity of conventional catalysts by 2 to 3 orders of magnitude. The feasibility of achieving selectivity to the desired THF product approaching 100% was demonstrated. The novel catalysts also demonstrated catalyst stability far superior to conventional furfural decarbonylation catalysts. The novel technology also demonstrated the ability to produce other valuable commercial products such as tetrahydrofurfuryl alcohol, 1,5-pentanediol, 2-methyl furan, and 2-tetrahydromethylfuran as co-products with THF. Based on the use of waste pulp mill hydrolysate as the biomass raw material source, the new technology will produce THF for a total manufacturing cost less than the raw material cost for the hydrocarbon-based feed stocks for conventional THF production. Commercial Applications: Selective catalytic reactive distillation of pulp mill waste hydrolysate will allow commercial production of “green” THF from biomass feedstocks for the production of “green” elastomer fibers, and industrial solvents. The new technology will benefit the U.S. pulp and paper industry by providing new technologies and products from pulp and paper manufacture, which can enhance industry profitability, and increase industry employment. Development of commercially competitive biomass based technologies will reduce consumption of scarce hydrocarbon resources, and improve long term U.S. competitiveness in global markets.

09 BIOMASS FUELS↗

Simulating Catalysis with Realistic Pellet Geometries Using Mesoflow: A Case Study of Catalytic Propane Dehydrogenation

We present a case study of catalytic propane dehydrogenation with our open-source multiphysics solver, Mesoflow. The solver was developed to simulate reactive flow coupled to heterogeneous catalytic reactions and deactivation in the context of complex, mesoscale geometry. The method leverages cartesian block-structured adaptive mesh refinement to capture realistic catalyst microstructural features acquired directly from X-ray computed tomography data. A kinetic model for propane dehydrogenation and catalyst deactivation was developed based on temporal analysis of products (TAP) reactor experiments. The TAP reactor experiments allow for precise characterization of intrinsic kinetic reaction steps which are implemented into Mesoflow simulations to model the spatial and temporal evolution of reactants, products, and catalyst active sites. The short-term and long-term deactivation behavior is studied by using XCT data collected from fresh and aged catalyst pellets, which exhibit different microstructural features. This study employs time-splitting algorithms to connect disparate reaction and flow timescales, enabling the simulations to achieve realistic deactivation timescales on the order of minutes while the flow time-scales for small particles (100 microns) are several milliseconds. We also introduce a flexible automated python script that writes the necessary files to construct a Mesoflow simulation from user-created chemical mechanisms. We will also introduce a few new features that are added to Mesoflow such as higher order schemes, implicit chemistry integrators and the ability to run on AMD and NVIDIA graphics-processing-units.

AMReX↗

Single Ru Atoms Stabilized by Hybrid Amorphous/Crystalline FeCoNi Layered Double Hydroxide for Ultraefficient Oxygen Evolution

Abstract In view of the sluggish kinetics suppressing the oxygen evolution reaction (OER), developing efficient and robust OER catalysts is urgent and essential for developing efficient energy conversion technologies. Herein, hybrid amorphous/crystalline FeCoNi layered double hydroxide (LDH)‐supported single Ru atoms (Ru SAs/AC‐FeCoNi) are developed for enabling a highly efficient electrocatalytic OER. The amorphous outer layer in Ru SAs/AC‐FeCoNi is composed of abundant defect sites and unsaturated coordination sites, which can serve as anchoring sites to stabilize single Ru atoms. The crystalline inner has a highly symmetric rigid structure, thereby strengthening the stability of support for a long‐lasting OER. The synergistic effects endow this hybrid catalyst with extremely low overpotential (205 mV at 10 mA cm −2 ). Density functional theory calculation indicates that single Ru atoms stabilized by hybrid amorphous/crystalline FeCoNi LDH facilitate the formation of Ru–O* (rate‐determining step), thus accelerating the OER process.

Hu, Yidong↗

Mechanistic Insights into the Origins of Selectivity in a Cu-Catalyzed C–H Amidation Reaction

The catalytic transformation of C-H to C-N bonds offers rapid access to fine chemicals and high-performance materials, but achieving high selectivity from undirected aminations of unactivated C(sp 3 )-H bonds remains an outstanding challenge. Here, we report the origins of the reactivity and selectivity of a Cu-catalyzed C-H amidation of simple alkanes. Using a combination of experimental and computational mechanistic studies and energy decomposition techniques, we uncover a switch in mechanism from inner-sphere to outer-sphere coupling between alkyl radicals and the active Cu(II) catalyst with increasing substitution of the alkyl radical. The combination of computational predictions and detailed experimental validation shows that simultaneous minimization of both Cu-C covalency and alkyl radical size increases the rate of reductive elimination and that both strongly electron-donating and electron-withdrawing substituents on the catalyst accelerate the selectivity-determining C-N bond formation process as a result of a change in mechanism. These findings offer design principles for the development of improved catalyst scaffolds for radical C-H functionalization reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fuel Processors for PEM Fuel Cells

Fuel cells are being developed to power cleaner, more fuel efficient automobiles. The fuel cell technology favored by many automobile manufacturers is PEM fuel cells operating with H 2 from liquid fuels like gasoline and diesel. A key challenge to the commercialization of PEM fuel cell based powertrains is the lack of sufficiently small and inexpensive fuel processors. Improving the performance and cost of the fuel processor will require the development of better performing catalysts, new reactor designs and better integration of the various fuel processing components. These components and systems could also find use in natural gas fuel processing for stationary, distributed generation applications. Prototype fuel processors were produced, and evaluated against the Department of Energy technical targets. Significant advances were made by integrating low-cost microreactor systems, high activity catalysts, π-complexation adsorbents, and high efficiency microcombustor/microvaporizers developed at the University of Michigan. The microreactor system allowed (1) more efficient thermal coupling of the fuel processor operations thereby minimizing heat exchanger requirements, (2) improved catalyst performance due to optimal reactor temperature profiles and increased heat and mass transport rates, and (3) better cold-start and transient responses.

08 HYDROGEN↗

Mononuclear ruthenium polypyridine complexes that catalyze water oxidation

Over the past decade, significant advances have been made in the development of molecular water oxidation catalysts (WOCs) in the context of developing a system that would accomplish artificial photosynthesis. Mononuclear ruthenium complexes with polypyridine ligands have drawn considerable attention in this regard, due to their high catalytic activity and relatively simple structure. In this perspective review, we will discuss mononuclear Ru polypyridine WOCs by organizing them into four groups according to their ligand environments. Each group will be discussed with regard to three fundamental questions: first, how does the catalyst initiate O–O bond formation? Second, which step in the catalytic cycle is rate-determining? Third, how efficient is the catalyst according to the specific descriptors such as turnover frequency? All discussion is based on the high-valent ruthenium intermediates that are proposed in the catalytic cycle according to experimental observation and theoretical simulation. Two fundamental mechanisms are set forth. An acid–base mechanism that involves the attack of a water molecule on the oxo of a high valent Ru=O species to form the O–O bond. Subsequent steps lead to dissociation of O 2 and rehydration of the metal center. A second mechanism involves the formation of a Ru–O˙ radical species, two of which then couple to form a Ru–O–O–Ru species that can release O 2 afterwards. The acid–base mechanism appears to be more common and mechanistic differences could result from variation directly related to polypyridine ligand structures. Thus, understanding how electronic, steric, and conformational properties can effect catalyst performance will lead to the rational design of more effective WOCs with not only ruthenium but also other transition metals.

14 SOLAR ENERGY↗

Mechanistic insights into metal, nitrogen doped carbon catalysts for oxygen reduction: progress in computational modeling

We report metal and nitrogen doped carbon materials (denoted as M–N–C) synthesized through high-temperature pyrolysis have been found to exhibit activity for oxygen reduction reaction (ORR) approaching that of Pt and electrochemical stability higher than previous MN 4 -containing macrocyclic molecular catalysts. Tremendous efforts have thus been devoted to the advancement of M–N–C catalysts as an economical alternative to Pt-based catalysts for proton exchange membrane fuel cell cathodes with a focus on simultaneously improving activity and stability. To this end, novel computational modeling techniques have been developed and applied to acquire knowledge crucial for accelerating the pace of M–N–C catalyst development. In this review, recent progress in computational method development, as well as the predictions of chemical structure of active sites, reaction pathways, ORR kinetics, and catalyst stability in electrochemical environments, are critically surveyed. Moreover, the crucial role of computational modeling to elucidate the functional mechanism of M–N–C catalysts for ORR in acid media and enable rational design of M–N–C catalysts is discussed with a visionary outlook for the field.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Mild oxidation of methane to methanol or acetic acid on supported isolated rhodium catalysts

An efficient and direct method of catalytic conversion of methane to liquid methanol and other oxygenates would be of considerable practical value. However, it remains an unsolved problem in catalysis, as typically it involves expensive or corrosive oxidants or reaction media(5-8) that are not amenable to commercialization. Although methane can be directly converted to methanol using molecular oxygen under mild conditions in the gas phase, the process is either stoichiometric (and therefore requires a water extraction step) or is too slow and low-yielding to be practical. Methane could, in principle, also be transformed through direct oxidative carbonylation to acetic acid, which is commercially obtained through methane steam reforming, methanol synthesis, and subsequent methanol carbonylation on homogeneous catalysts. However, an effective catalyst for the direct carbonylation of methane to acetic acid, which might enable the economical small-scale utilization of natural gas that is currently flared or stranded, has not yet been reported. Here we show that mononuclear rhodium species, anchored on a zeolite or titanium dioxide support suspended in aqueous solution, catalyse the direct conversion of methane to methanol and acetic acid, using oxygen and carbon monoxide under mild conditions. Here, we find that the two products form through independent pathways, which allows us to tune the conversion: three-hour-long batch-reactor tests conducted at 150 degrees Celsius, using either the zeolitesupported or the titanium-dioxide-supported catalyst, yield around 22,000 micromoles of acetic acid per gram of catalyst, or around 230 micromoles of methanol per gram of catalyst, respectively, with selectivities of 60-100 per cent. Finally, we anticipate that these unusually high activities, despite still being too low for commercial application, may guide the development of optimized catalysts and practical processes for the direct conversion of methane to methanol, acetic acid and other useful chemicals.

09 BIOMASS FUELS↗

Catalytic Removal of Oxygen and Pollutants in Exhaust Gases from Pressurized Oxy-Combustors

The primary goal of this project was to develop and validate advanced catalytic materials and systems for purifying the flue gas generated from pressurized oxy-combustors in an effort to achieve the purity specifications of carbon dioxide (CO 2 ) streams required by the U.S. Department of Energy (USDOE) for application in enhanced oil recovery. The technology has shown great potential for improving energy efficiency, simplifying process complexity, and lowering costs compared with current state-of-the-art oxy-combustion flue gas purification technologies. Laboratory studies were conducted for the development, characterization, and screening of metal catalysts for residual oxygen (O 2 ) reduction with methane (CH 4 ) and multifunctional carbon catalysts for combined nitrogen oxides (NO x ), sulfur oxides (SO x ), and mercury (Hg) removal. A bench-scale reverse-flow fixed-bed (RFFB) reactor and a trickle-bed direct-contact cooler (DCC) reactor capable of treating 15 standard liters per min of pressurized oxy-combustion flue gas were fabricated and tested with both a simulated flue gas in the laboratory and a slipstream of actual flue gas at a 100 kW th Staged, Pressurized Oxy-Combustion (SPOC) pilot facility. Process simulation and techno-economic studies were performed to evaluate the energy efficiency and cost of the developed catalytic flue gas purification process integrated into a conceptual 550-MWe SPOC power plant. The goal and objectives of the project have been successfully accomplished. A cobalt-manganese (CoMn) oxide catalyst was developed and demonstrated in the bench-scale RFFB reactor in either a reverse-flow or one-direction flow mode of operation that met the success criterion of performance for residual O 2 reduction. A carbon catalyst was developed and demonstrated in the bench-scale DCC reactor that met the success criterion of performance for combined NO x /SO x /Hg removal. Slipstream testing of the integrated DCC-RFFB system at the SPOC pilot facility demonstrated stable operation and verified the superior performance obtained in the laboratory. The techno-economic analysis showed that a 550-MWe SPOC plant integrated with the catalytic flue gas purification process would result in costs of electricity of $\$$96.94/MWh and $\$$80.27/MWh in two assessed cases compared with $\$$91.07/MWh reported for the USDOE’s Current Technology Case, which generated only a partially pure CO 2 stream. On the basis of the results and findings from this project, scale-up studies of materials production and system demonstration and optimization studies of reactors and processes are recommended at the next stage of technology development.

20 FOSSIL-FUELED POWER PLANTS↗

FermiLib v0.1

FermiLib is an open source software package designed to facilitate the development and testing of algorithms for simulations of fermionic systems on quantum computers. Fermionic simulations represent an important application of early quantum devices with a lot of potential high value targets, such as quantum chemistry for the development of new catalysts. This software strives to provide a link between the required domain expertise in specific fermionic applications and quantum computing to enable more users to directly interface with, and develop for, these applications. It is an extensible Python library designed to interface with the high performance quantum simulator, ProjectQ, as well as application specific software such as PSI4 from the domain of quantum chemistry. Such software is key to enabling effective user facilities in quantum computation research.

MCCLEAN, JARROD↗

A Ce-CuZn catalyst with abundant Cu/Zn-OV-Ce active sites for CO 2 hydrogenation to methanol

CO 2 hydrogenation to chemicals and fuels is a significant approach for achieving carbon neutrality. It is essential to rationally design the chemical structure and catalytic active sites towards the development of efficient catalysts. Here we show a Ce-CuZn catalyst with enriched Cu/Zn-OV-Ce active sites fabricated through the atomic-level substitution of Cu and Zn into Ce-MOF precursor. The Ce-CuZn catalyst exhibits a high methanol selectivity of 71.1% and a space-time yield of methanol up to 400.3 g·kg cat -1 ·h -1 with excellent stability for 170 h at 260°C, comparable to that of the state-of-the-art CuZnAl catalysts. Controlled experiments and DFT calculations confirm that the incorporation of Cu and Zn into CeO 2 with abundant oxygen vacancies can facilitate H 2 dissociation energetically and thus improve CO 2 hydrogenation over the Ce-CuZn catalyst via formate intermediates. This work offers an atomic-level design strategy for constructing efficient multi-metal catalysts for methanol synthesis through precise control of active sites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanocatalysis: Size- and Shape-dependent Chemisorption and Catalytic Reactivity

This review article focuses on correlating the catalytic reactivity of NPs and their geometry. It illustrated that chemisorption and catalytic properties such as the onset reaction temperature, the activity, and selectivity of a nanocatalyst may be tuned through controlled synthesis of NPs with well-defined sizes and shapes. It has become clear that detailed information on the physical/chemical properties of supported NP systems must be available for the rational design of the next generation of nanosized catalysts. Such NP systems must be representative of active catalysts, and must be sufficiently well-defined ( e.g., with respect to size and shape) to serve as a basis for theoretical modeling. In addition, a synergistic combination of in situ and in operando characterization techniques working under realistic reaction conditions ( e.g. elevated temperatures and high pressure) must be available, since the working state of a NP catalyst might not be the state in which the catalyst was prepared, but a structural and/or chemical isomer that adapted to the particular reaction conditions. In order to address the complexity of real-world catalysts, a synergistic approach taking advantage of a variety of state-of-the-art experimental and theoretical methods must be undertaken. In this review, we have described some of the impressive developments that have been made in these areas. Many serious challenges still remain in the areas of catalyst characterization and design. One such challenge is to design highly active metal NP catalysts using abundant, inexpensive metals which can replace precious metal catalysts. Additionally, there is an increasingly pressing need for catalyst development for energy production applications, such as in fuel cells or for the synthesis of chemicals and fuels. Further work is needed to design more active and selective catalysts for these reactions that are viable at an industrial scale. In the coming years, nanocatalysis research must meet these challenges by building on the work described in this report. Further advancements in developing new synthetic methods will allow increased control over NP structure and stability, allowing for new insights into NP structure-reactivity correlations. In addition, the development of higher resolution in situ and in operando measurement techniques capable of probing catalytic reactions at NP surfaces over an extended range of temperatures and pressures and harsh environmental conditions will give unprecedented insight into NP catalysts in their working state. Single-nanoparticle spectroscopic and catalytic characterization must also be further developed. Advancements in computational modeling of more realistic catalysts will also bring us closer to gaining a molecularlevel view of a reaction at a NP surface when used to complement experimental studies. Such progress will bring us closer to realizing the goal of synthesizing highly effective, tailor-made, tunable nanoparticle catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molecular Catalysts with Diphosphine Ligands Containing Pendant Amines

Pendant amines play an invaluable role in chemical reactivity, especially for molecular catalysts based on Earth-abundant metals. As inspired by [FeFe]-hydrogenases, which contain a pendant amine positioned for cooperative bifunctionality, synthetic catalysts have been developed to emulate this multifunctionality through incorporation of a pendant amine in the second coordination sphere. Cyclic diphosphine ligands containing two amines serve as the basis for a class of catalysts that have been extensively studied and used to demonstrate the impact of a pendant base. These 1,5-diaza-3,7-diphosphacyclooctanes, now often referred to as “P 2 N 2 ” ligands, have profound effects on the reactivity of many catalysts. The resulting [Ni(P R 2 N R ´ 2 ) 2 ] 2+ complexes are electrocatalysts for both the oxidation and production of H 2 . Achieving the optimal benefit of the pendant amine requires that it has suitable basicity and is properly positioned relative to the metal center. In addition to the catalytic efficacy demonstrated with [Ni(P R 2 N R ´ 2 )2] 2+ complexes for the oxidation and production of H2, catalysts with diphosphine ligands containing pendant amines have also be demonstrated for a variety of metals for many different reactions, both in solution and immobilized on surfaces. Here, the impact of pendant amines in catalyst design has been demonstrated and continues to expand.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗